LG Electronics USA 9QKE40250 VCR / DVD/CD/MP3 Player AM/FM Receiver User Manual DT 587M OM Zenith

Download:
Mirror Download [FCC.gov]
Document ID	270384
Application ID	Q2tJN+4wUhxZiO8fDwFbdQ==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	103.57kB (1294585 bits)
Date Submitted	2002-09-13 00:00:00
Date Available	2002-09-13 00:00:00
Creation Date	2002-09-02 12:31:08
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2002-09-12 11:23:05
Document Title	DT-587M_OM_Zenith
Document Creator	QuarkXPressª 4.11: LaserWriter 8 Z1-8.7.1
Document Author:	ytkg4

Installation and Operating Guide | Warranty
Model Number | XBS245 | Combi Home Theater System
© Copyright 2002, Zenith Electronics Corporation
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
WARNING: Do not install this equipment in a confined space
such as a bookcase or similar unit.
NOTE TO CABLE/TV INSTALLER: This reminder is provided to
call the cable TV system installer’s attention to Article 820-40 of
the National Electric Code (U.S.A.). The code provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of the cable entry as practical.
CAUTION:
This DVD+VCR employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference. Should the
unit require maintenance, contact an authorized service
location.
Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the product and
receiver.
 Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician
for help.
FCC COMPLIANCE: The responsible party for this product’s
compliance is: Zenith Electronics Corporation, 2000 Millbrook
Drive, Lincolnshire, IL 60069, USA.
Phone: 1-847-941-8000
NOTES ON COPYRIGHTS:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product features the copy protection function developed
by Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ___________________________________
Serial No. ___________________________________
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.
AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this product near water. – For example:
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement; or near a swimming pool; and
other areas located near water.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been
adhered to.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution
when moving the cart/product combination to
avoid injury from tip-over.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Display Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Connecting Antenna/Cable TV to a DVD+VCR . . 11
Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12
Optional TV Connections . . . . . . . . . . . . . . . . . . 12
Speaker System Connections . . . . . . . . . . . . . . 13
Speaker Positioning . . . . . . . . . . . . . . . . . . . . . . 13
Radio Antenna Connections . . . . . . . . . . . . . . . . 14
Accessory Audio/Video (A/V) Connections to
DVD+VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Degital Device Connections . . . . . . . . . . . . . . . . 14
Before Operation - Amplifier Part . . . . . . . . . . 15-17
Mini Glossary for Sound Mode . . . . . . . . . . . . . . 15
Sound Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Sound Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Test Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Delay Time Setting. . . . . . . . . . . . . . . . . . . . . . . 17
Before Operation - VCR Part . . . . . . . . . . . . . . 18-20
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the On-Screen Display . . . . . . . . . . . . . . 18
Setting the VCR Setup Menu . . . . . . . . . . . . . . . 19
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 20
Before Operation - DVD Part . . . . . . . . . . . . . . 21-23
General Explanation. . . . . . . . . . . . . . . . . . . . . . 21
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 21
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 22-23
 Initial Settings General Operation . . . . . . . . . 22
 Language . . . . . . . . . . . . . . . . . . . . . . . . . . 22
 PBC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
 Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
 Parental Control . . . . . . . . . . . . . . . . . . . . . . 23
Operation with DVD and Video CD - DVD Part . . 30-35
Playing DVD and Video CD . . . . . . . . . . . . . . . . 30
General Features . . . . . . . . . . . . . . . . . . . . . . . . 30
 Moving to another TITLE . . . . . . . . . . . . . . . 30
 Moving to another CHAPTER/TRACK . . . . . 30
 Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 30
 Still Picture and Frame-by-Frame Playback . 31
 Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
 Random. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
 Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
 Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 29
 Time Search . . . . . . . . . . . . . . . . . . . . . . . . 31
 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 31
 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
 Marker Search . . . . . . . . . . . . . . . . . . . . . . . 32
Special DVD Features . . . . . . . . . . . . . . . . . . . . 32
 Checking the contents of DVD Video discs: Menus . 32
 Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 32
 Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 32
 Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 32
 Changing the Audio Language . . . . . . . . . . . 32
 Changing the Audio Channel . . . . . . . . . . . . 32
 Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Operation with Audio CD and MP3 Discs - DVD Part . . 33
Playing an Audio CD and MP3 Discs . . . . . . . . . 33
 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
 Moving to another Track . . . . . . . . . . . . . . . 33
 Repeat Track/ All/ Off. . . . . . . . . . . . . . . . . . 33
 Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
 Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
 Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 33
 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 33
 Changing the Audio Channel . . . . . . . . . . . . 33
Programmed Playback - DVD Part . . . . . . . . . . . . 34
Programmed Playback with Audio CD
and MP3 Discs . . . . . . . . . . . . . . . . . . . . . . . . . 34
Programmed Playback with Video CD . . . . . . . . 34
 Repeat Programmed Tracks . . . . . . . . . . . . 34
 Erasing a Track from Program List . . . . . . . . 34
 Erasing the Complete Program List . . . . . . . 34
Additional Information - DVD Part . . . . . . . . . . . . 35
Last Condition Memory . . . . . . . . . . . . . . . . . . . 35
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Video Mode Setting . . . . . . . . . . . . . . . . . . . . . . 35
Notes on MP3 Discs . . . . . . . . . . . . . . . . . . . . . 35
Operation with Radio . . . . . . . . . . . . . . . . . . . . . . 36
Presetting Radio Stations . . . . . . . . . . . . . . . . . . 36
Listening to the Radio . . . . . . . . . . . . . . . . . . . . 36
Operation
Operation with tape - VCR Part . . . . . . . . . . . . 24-29
Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 24
Special Effect Playbacks . . . . . . . . . . . . . . . . . . 24
 Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
 Still Picture and Frame-by-Frame Playback . 24
 Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 24
 CM SKIP (Commercial Skip) . . . . . . . . . . . . 24
Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 25
Timer Recording . . . . . . . . . . . . . . . . . . . . . . 25-26
Instant Timer Recording . . . . . . . . . . . . . . . . . . . 27
Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 27
Copying from DVD to VCR. . . . . . . . . . . . . . . . . 27
VHS Hi-Fi Stereo System/MTS Broadcast . . . . . 28
Tape Counter Memory Feature. . . . . . . . . . . . . . 29
Additional Information . . . . . . . . . . . . . . . . . . . . 29
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 37-38
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 39
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 40
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 41-42
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . Rear Cover
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
Before Use
Title (DVD only)
The main film content or accompanying feature content
or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
Audio CD
(8 cm/12 cm disc)
In addition, this unit can play a CD-R or CD-RW that
contains audio titles or MP3 files.
Notes
– Depending on the conditions of the recording equipment or the CD-R/RW disc itself, some CD-R/RW
discs cannot be played on the unit.
– The unit cannot play discs that contain data other
than MP3 and CD-DA data.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heartshaped or octagonal). It may result in malfunctions.
Regional code of the DVD+VCR and DVDs
This DVD+VCR is designed and manufactured
for playback of Region 1 encoded DVD software.
The region code on the labels of some DVD discs indicates which type of DVD+VCR can play those discs. This
unit can play only DVD discs labeled 1 or ALL. If you try
to play any other discs, the message “Check Regional
Code” will appear on the TV screen. Some DVD discs
may not have a region code label even though their playback is prohibited by area limits.
Note on DTS-encoded CDs
When playing DTS-encoded CDs, excessive noise may
be exhibited from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy
DTS Digital SurroundTM playback, an external 5.1 channel DTS Digital SurroundTM decoder system must be
connected to the digital output of the unit.
Track (audio CD only)
Sections of a musical piece on an audio CD. Each track
is assigned a track number, enabling you to locate the
track you want.
Remote control battery installation
AAA
Notes on DVDs
Some playback operations of DVDs may be intentionally
fixed by software manufacturers. As this unit plays
DVDs according to disc content designed by the software manufacturer, some playback features of the unit
may not be available or other functions may be added.
Refer also to the instructions supplied with the DVDs.
Some DVDs made for business purposes may not be
played on the unit.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number to
enable you to locate the chapter you want. Depending
on the disc, chapters may not be labelled.
AAA
DVD
(8 cm/12 cm disc)
Detach the battery cover on the rear of the
remote control, and insert two R03 (size
AAA) batteries with
and
aligned
correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
 Distance: About 23 ft (7 m) from the front of the
remote sensor
 Angle: About 30° in each direction of the front of the
remote sensor
IMPORTANT NOTE:
SPENT OR DISCHARGED BATTERIES MUST BE
RECYCLED OR DISPOSED OF IN A SAFE MANNER
IN COMPLIANCE WITH ALL APPLICABLE LAWS.
FOR DETAILED INFORMATION, CONTACT YOUR
LOCAL COUNTY SOLID WASTE AUTHORITY.
INTRODUCTION
Disc-related terms
Playable Discs
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center outward.
Yes
No
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Cleaning the unit
About the
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD+VCR is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature
increase inside the car.
About Symbols
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbols are
applicable only to those discs represented by the symbol.
DVD DVD
CD
Audio CDs.
MP3 MP3 Discs.
Setting the Output Source
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
• If you want to view output from the DVD deck:
Press DVD on the remote or DVD/VCR on the front panel
until DVD indicator on the front panel lights and output from
the DVD deck is viewed on the TV screen.
• If you want to view from the VCR deck:
Press VCR on the remote or DVD/VCR on the front panel
until VCR indicator on the front panel lights and output from
the VCR deck is viewed on the TV screen.
• If you use OUTPUT SELECT button on the remote control to select output source:
Cycles through the 3 main output views: DVD, Tuner and VCR.
DVD: To view the current DVD deck status. (disc playback,
DVD menu or setup menu, etc)
Tuner: To view TV programs through TV tuner.
VCR: To view the current VCR deck status (tape playback,
VCR programming or viewing TV programs through
the VCR tuner, etc).
Front Panel
EJECT
Ejects the tape in the VCR deck.
POWER
Switches the DVD+VCR ON and OFF.
X)
PAUSE/STEP (X
Pause playback or recording
temporarily/press repeatedly for
frame-by-frame playback.
Disc Tray (DVD deck)
Insert a disc here.
v/V
V)
TUNNIING (v
Scans an available channel in
the area.
COPY/MEMORY
Press to copy a DVD
in the DVD deck to a
VCR tape in the VCR
deck.
Memories a frequency of radio.
INTRODUCTION
VOLUME
Adjusts volume of speakers.
VIDEO IN/AUDIO IN (Left/Right)
Connect the audio/video output of an
external source (Audio system, TV/ Monitor,
Another VCR).
x)
STOP (x
Stops playback.
H)
PLAY (H
To play back a recorded tape.
z)
REC/ITR (z
To record normally or
to activate Instant
Timer Recording.
Cassette Compartment
(VCR deck)
Insert a video cassette here.
RADIO
Selects operation
mode to radio.
v/V
V)
CH/PRESET (v
To scan up or down through
memorized channels or radio frequency.
Remote Sensor
Point the DVD+VCR remote control
here.
Display window
Shows the current
status of the
DVD+VCR.
OPEN/CLOSE
Opens or closes
the disc tray.
DVD/VCR
Toggles control
between the DVD deck
and the VCR deck.
>/M
M)
FORWARD (>
DVD: Go to NEXT chapter/track. Press and hold for two seconds for a fast forward search.
VCR: Advances the tape during the STOP mode or for fast forward picture search.
./m
m)
BACKWARD (.
DVD: Go to beginning of current chapter/track or to previous chapter/track.
Press and hold for a fast reverse search.
VCR: Rewinds the tape during the STOP mode or for fast reverse picture search.
Display Window
RAND RANDOM playback active
SP LP EP Displays the recording
and playback speed.
Indicates repeat mode
A cassette is in the VCR deck.
ANGLE active
PROG. Programmed playback active.
Indicates current encoding method of the disc.
HI-FI Indicates the unit is playing back
a tape recorded in Hi-Fi.
OPT Indicates source of DVD+VCR is
DIGITAL AUDIO IN.
COPY DVD to VCR copy is in progress.
Indicates sound mode is
PROLOGIC II.
REC DVD+VCR is Recording.
TIMER DVD+VCR is in timer recording or a timer
recording is programmed.
VCR DVD+VCR functions are available and
channels are selected at DVD+VCR.
Indicates clock, total playing time, elapsed time, remaining time, title number,
chapter/track number, channel, frequency, level, volume, channel or current
deck status (Playback, Pause, etc).
STEREO Indicates a stereo broadcast is being received.
SAP Indicates when a SAP BILINGUAL broadcast is being received.
DVD DVD inserted.
CD Audio CD inserted.
MP3 MP3 disc inserted
Remote Control
POWER
Z)
OPEN/CLOSE, EJECT (Z
Switches DVD+VCR ON and OFF.
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
Selects sound mode.
PLOROGIC II
Selects sound mode of PROLOGIC II.
Select the output source (DVD,VCR, AUX
or RADIO) to view on the TV screen.
BY PASS
Sets PRO LOGIC II mode to Off
LEVEL
CLEAR
Sets the sound leve of each speakerl.
Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
DELAY
Sets the delay time of each speaker.
AUDIO
TEST TONE
Selects an audio language (DVD) or an
audio channel (VCD/CD).
A hiss noise comes out for 2 seconds
from each speakers.
ZOOM
MUTE
Turn off speaker sound.
Enlarges DVD video image.
ANGLE
Selects a DVD camera angle if
available.
0-9 numerical buttons
Selects numbered options in a menu.
SUBTITLE
PROGRAM
Selects a subtitle language.
TITLE
Accesses or removes Program menu.
Displays the disc’s Title menu, if
available.
MARKER
Marks any point during playback.
DISPLAY, CLK/CNT
SEARCH
Accesses On-Screen display.
Switches among the clock, tape counter
and tape remaining modes on the display.
Displays MARKER SEARCH menu.
INPUT
SETUP, MENU
To select the VCR deck’s source (Tuner,
LINE 1, or LINE 2).
Accesses or removes DVD setup menu
and VCR menu.
b/B/v/V (left/right/up/down)
- Selects an option in the menu
- CH/TRK (v/V): Selects channel of VCR.
Adjusts manually the tape’s picture
onscreen.
OUTPUT SELECT
Cycles through the 3 main output views:
DVD, Tuner and VCR.
VOLUME (+/–)
Adjusts volume of speaker.
DISC MENU
Accesses menu on a DVD disc.
RETURN
TV/VCR
Removes the setup menu.
To view channels selected by the VCR
tuner or by the TV tuner.
x)
STOP (x
Stops playback.
SELECT/ENTER
X)
PAUSE/STEP (X
- Acknowledges menu selection.
- Displays functions on the TV screen.
Pause playback or recording
temporarily/press repeatedly for frameby-frame playback.
>)
FORWARD (>
H)
PLAY (H
Search forward*/go to next chapter or
track (DVD). Advances the tape during
the STOP mode or for fast forward picture search. (VCR)
Starts playback.
z)
REC/ITR (z
Records normally or activates Instant
Timer Recording.
.)
BACKWARD (.
A-B, SPEED
- Repeats sequence.
- Selects recording speed
REPEAT
Repeat chapter, track, title, all.
RANDOM, CM SKIP
- Plays tracks in random order.
- Fast forwards picture search through
30 seconds of recording.
Note
This remote control use the
same buttons for VCR or DVD
functions (ex. PLAY).
When using a VCR, first press
the VCR button.
When using a DVD, first press
the DVD button.
Search backward*/go to beginning of
current chapter or track or go to previous chapter or track (DVD). Rewinds the
tape during the STOP mode or for fast
reverse picture search. (VCR)
* Press and hold button for about two
seconds.
INTRODUCTION
SOUND EFFECT
AUX/DVD/VCR/RADIO
select buttons
Rear Panel
VCR IN LINE 1 (VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external source
(Audio system, TV/Monitor, Another VCR).
RF OUT (DVD/VCR OUT)
Connect to a TV with RF coaxial inputs.
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
COMPONENT VIDEO OUT (Y Pb Pr) (DVD OUT)
Connect to a TV with Y Pb Pr inputs.
ANT.IN
Connect the VHF/UHF/CATV antenna to
this terminal.
AC Power Cord
Plug into the power source.
S-VIDEO OUT (DVD OUT)
Connect to a S-Video Input on TV.
DIGITAL AUDIO IN (OPTICAL)
Connect to a digital audio output on a digital device.
VIDEO OUTPUT Switch
Select either S-VIDEO OUT or COMPONENT VIDEO OUT/PROGRESSIVE
SCAN, depending on how you connected the DVD+VCR to the TV.
AM Antenna Connectors
Connect the AM antenna to this terminal.
Dust Protection Cap
Remove the dust protection cap from the
OPTICAL DIGITAL IN jack and connect the
optical digital cable (not supplied) securely
so that the configurations of both the cable
and the connector match. Keep the dust
protection cap and always reattach the cap
when not using the connector to protect
against dust intrusion.
10
FM Antenna Connector
Connect the FM antenna to this terminal.
SPEAKER Connectors
Connect the FM antenna to this terminal.
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
Connections
Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
DVD+VCR. Use connections described on pages 11-14.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the best
connections.
Caution
If your cable wire is connected to your TV without a converter
or descrambler box, unscrew the wire from your TV and attach
it to the ANT.IN jack on the DVD+VCR. Use the supplied round
coaxial cable to connect between the DVD+VCR’s RF.OUT
jack and the 75 ohm antenna input jack on the TV. With this
connection, you can receive all midband, super band, and
hyperband channels.
With Cable Box
Make sure the DVD+VCR is connected directly to the TV.
Tune the TV to the correct video input channel.
Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT
jack to the phono in jack (record deck) of your audio
system.
Do not connect your DVD+VCR via your VCR. The DVD
image could be distorted by the copy protection system.
Connecting Antenna/Cable TV to
DVD+VCR
Disconnect the antenna leads from the rear of the
TV.
the type of cable from your antenna. If it is
2 Identify
a round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to
If a converter is required in your cable system, follow the
instruction below:
The cable hookup permits both TV and DVD+VCR operation.
To view or record CATV channel
1 Tune the TV to the DVD+VCR output channel (CH 3 or 4).
2 Set the DVD+VCR channel selector to the output channel of
the Cable Converter box by pressing the CH/TRK (v/V) or
number (0-9) of your DVD+VCR. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
Notes
With this connection, you CANNOT record one program
while viewing another.
If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming, (Auto Channel
Search) as indicated on page 19.
the jack marked ANT.IN on your DVD+VCR.
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
Tip
If your antenna lead wire is a flat type antenna cable,
connect it to an Antenna Adaptor (300-ohm to 75-ohm)
(not supplied) and slip the Adaptor onto the ANT.IN
jack. The Adaptor does not screw on to the DVD+VCR,
it just slips over the jack.
Antenna
Antenna
Cable TV
Wall Jack
Flat Wire
(300 ohm)
300/75 ohm
Adaptor
(Not supplied)
OR
OR
Rear of DVD+VCR
Rear of DVD+VCR
11
PREPARATION
Without Cable Box
Tips
Connections (Continued)
Basic TV Connections
Optional TV Connections
Make one of the following connections, depending on
the capabilities of your existing equipment.
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
Note
If you use this connection, tune the TV to the
DVD+VCR’s RF output channel (CH 3 or 4).
How to set the DVD+VCR’s RF output channel
When the DVD+VCR is turned off, press and hold
CHANNEL (v/V) on the front panel for about five
seconds to change the RF output channel (CH 03 or
CH 04). “RF 03” or “RF 04” appears in the display
window.
Audio/Video connection
Connect the DVD/VCR VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using the
video cable supplied (V).
the Left and Right DVD/VCR AUDIO OUT
2 Connect
jacks on the DVD+VCR to the audio left/right in
jacks on the TV (A) using the supplied audio
cables.
Note
If you use this connection, set the TV’s source selector
to VIDEO.
Notes
DVD playback can ONLY be done using the S-VIDEO
OUT and COMPONENT VIDEO OUT/PROGRESSIVE
SCAN connection options below. The tuner and VCR
will still output through the RF.OUT (R) or DVD/VCR
OUT (A, V) jack. (See left)
When using the COMPONENT VIDEO OUT/PROGRESSIVE SCAN jacks, set the VIDEO OUTPUT
switch to COMPONENT/PROGRESSIVE. When
using the S-VIDEO OUT jack, set the VIDEO OUTPUT switch to S-VIDEO.
S-Video connection
the Left and Right AUDIO OUT jacks of the
2 Connect
DVD+VCR to the audio left/right in jacks on the TV
using the supplied audio cables (A).
Component Video (Color Stream®) connection
VIDEO
INPUT
AUDIO INPUT
S-VIDEO
INPUT
COMPONENT VIDEO INPUT
Pr
Pb
Progressive Scan (ColorStream® pro) connection
Connect the COMPONENT VIDEO OUT jacks on
the DVD+VCR to the corresponding in jacks on the
TV using user-supplied Y Pb Pr cables (C).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD+VCR to the audio left/right in jacks on the
TV (A) using the supplied audio cables.
Rear of TV
ANTENNA
INPUT
Connect the S-VIDEO OUT jack on the DVD+VCR
to the S-Video in jack on the TV using the supplied
S-Video cable (S).
If your television is a high-definition or “digital ready”
television, you may take advantage of the
DVD+VCR’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the DVD+VCR.
Connect the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks on the DVD+VCR to
the corresponding in jacks on the TV using an
optional Y Pb Pr cable (C).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD+VCR to the audio left/right in jacks on the
TV (A) using the supplied audio cables.
Notes
– Set the Progressive to “On” on the setup menu for
progressive signal, see page 22.
– Progressive scan does not work with the analog video
connections (yellow VIDEO OUT jack).
Rear of DVD+VCR
12
Speaker System Connections
Speaker Positioning
Connect the speakers using the supplied speaker cords
by matching the colors of the terminals and those of the
cords. To obtain the best possible surround sound,
adjust the speaker parameters (distance, level, etc.).
In the case of normal position use the 6 speakers
(2 front speakers, center speaker, 2 rear speakers and
subwoofer).
If you want to hear deeper bass sound, DTS digital surround or Dolby Digital surround, you should connect an
optional active subwoofer (has its own built-in amplifier).
Note
Be sure to match the speaker cord to the appropriate
terminal on the components: + to + and – to –. If the
cords are reversed, the sound will be distorted and
lack bass.
If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive
volume output to the speakers.
Do not disassemble the front covers of supplied
speakers.
Center speaker
Front speaker
(Left)
Front speaker
(Right)
• Front speakers
According to your listening position set up the speakers for equal distance. And by hearing position set up
the interval between speakers at 45 degree.
• Center speaker
It is ideal that the center speakers and front speakers
are same height. But normally place it above or below
the television as shown below.
• Rear speakers
Place left and right behind the listening area. These
speakers recreate sound motion and atmosphere
required for surround playback. For best results, do
not install the rear speakers too far behind the listening position, install them at or above the level of the
listener’s ears. It is also effective to direct the rear
speakers towards a wall or ceiling to further disperse
the sound.
In the case of a smaller room size, if the audience is
near to the rear wall set the rear speakers opposite
each other, and set the rear speakers 60 - 90 cm
above the listener’s ears.
• Subwoofer
This can be placed in any front position.
Rear of
DVD+VCR
Subwoofer
Center Speaker
Front
Speaker
(Left)
Front
Speaker
(Right)
Rear
Speaker
(Right)
Rear
Speaker
(Left)
Speaker Positioning Example
Rear speaker
(Right surround)
Left speaker
(Left surround)
Subwoofer
13
PREPARATION
Connections (Continued)
Connections (Continued)
Radio Antenna Connections
Digital Device Connections
Connect the supplied FM/AM antennas for listening to
the radio.
Connect the DIGITAL AUDIO IN (OPTICAL) jacks on
the DVD+VCR to the digital audio out (optical) jacks on
your digital device (DVD Player, etc.), using optional
optical audio cables.
To select source of DVD+VCR to OPTICAL IN, press
AUX on the remote control.
the AM loop antenna to the AM antenna
1 Connect
connector.
the FM wire antenna to the FM 300Ω
2 Connector
antenna connector.
Note
To prevent noise pickup, keep the AM loop antenna
away from the DVD Receiver and other components.
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it as horizontal as possible.
ote
If the audio format of the digital output does not
match the capabilities of your DVD+VCR, the
DVD+VCR will produce a strong, distorted sound or
no sound at all.
The Optical input function is available only when the
other unit’s Sampling Frequency is 32 - 48kHz.
AM loop antenna (supplied)
Game Devive
FM wire antenna (supplied)
OR
Rear of DVD+VCR
Accessory Audio/Video (A/V)
Connections to DVD+VCR
Connect the VCR IN LINE1 or LINE2 jacks on the
DVD+VCR to the audio/video out jacks on your
accessory component, using optional audio/video
cables.
Jack panel of Accessory Component
(VCR, Camcorder, etc.)
AUDIO
OUTPUT
VIDEO
OUTPUT
OR
Rear of DVD+VCR
14
Front of DVD+VCR
Rear of DVD+VCR
HDTV Receiver
Before Operation - Amplfier Part
Allows you to enjoy 5.1(or 6) discrete channels of high quality digital audio from DTS program sources bearing the
trademark such as discs, DVD and compact discs, etc. DTS Digital Surround delivers up to 6 channels of transparent audio(which means identical to the original masters) and results in exceptional clarity throughout a true 360
degree sound field. The term DTS is a trademark of DTS Technology, LLC. Manufactured under license from DTS
Technology, LLC.
The Dolby Digital surround format lets you enjoy up to 5.1 channels of digital surround sound from a Dolby Digital
program source. If you play DVDs with “
” mark, you can enjoy even better sound quality, greater spatial
accuracy, and improved dynamic range.
When playing recordings of live music and classic, this mode provides a feeling similar to actually being in a small
concert hall.
When playing recordings of live music and classic, this mode provides a feeling similar to actually being in a large
concert hall.
This mode provides a three dimensional effect similar to that of movie theater.
(II)
Dolby Pro Logic II creates five full-bandwidth output channels from two-channel sources. This is done using an
advanced, high-purity matrix surround decoder that extracts the spatial properties of the original recording without
adding any new sounds or tonal colorations.
PROLOGIC mode:
The Pro Logic Emulation mode offers users the same robust surround processing as original Pro Logic, in case
the source content is not of optimum quality, or if there is a desire to hear the program more “as it used to be.”
When this mode is used, it is called Pro Logic, as before. There is no “Pro Logic I” mode. The Pro Logic emulation mode is optional. Dolby does not require PLII products to use the original Pro Logic decoding algorithm.
However, if the DSP contains the original Pro Logic code, and if the product maker would like to use it, this is
quite acceptable and even encouraged. A product must not offer both original Pro Logic and the Pro Logic emulation mode.
MOVIE mode:
The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround. The result
is enhanced soundfield directionality that approaches the quality of discrete 5.1-channel sound.
MUSIC mode:
The Music mode is for use with any stereo music recordings, and provides a wide and deep sound space. The
Music mode includes controls that allow the sound to be tailored to individual listening tastes.
VIRTUAL mode:
The Virtual mode is usually used when Pro Logic II is connected to a virtual process for speaker use. However,
there might be some virtualizers for which this mode does not produce the intended result. For those virtualizers,
Movie mode may give the best surround effect. Virtual mode is designed to be used with the virtual process
developed by Dolby Laboratories. The Pro Logic II mode should be called only “Pro Logic II” so the Virtual name
can be reserved to describe the speaker virtualization process itself.
MATRIX mode:
The Matrix mode is the same as the Music mode except that the directional enhancement logic is turned off. It
may be used to enhance mono signals by making them seem “larger.” The Matrix mode may also find use in auto
systems, where the fluctuations from poor FM stereo reception can otherwise cause disturbing surround signals
from a logic decoder. The ultimate “cure” for poor FM stereo reception may be simply to force the audio to mono.
SURROUND OFF (2CH STEREO)
Outputs the sound from the front left and right speakers and subwoofer. Standard two channel (stereo) sources
completely bypass the sound field processing. This allows you to play any source using only the front left and right
speakers and subwoofer. You can select SURROUND OFF by pressing BY-PASS on the remote control.
15
PREPARATION
Mini Glossary for Sound Mode
Before Operation - Amplfier Part (Continued)
Sound Mode
Note
You can enjoy surround sound simply by selecting one
of the pre-programmed sound fields according to the
program you want to listen to.
Each time you press SOUND EFFECT button, the
sound mode is changed as the following order;
PROLOGIC → HALL 1 → HALL 2 → THEATER
When you play sound tracks with 96kHz sampling frequency,
the output signals will be converted to 48kHz (sampling frequency).
Sound Level
You can set the sound level of the desired channel.
Note
1 Press LEVEL.
2 Press b/BB to select a desired speaker to set.
The level indicator will appear in the display window.
For the DVD, you can select only when PCM indicator is
shown in the display window.
Each time you press the b/B button, it is changed as the
following order;
Each time you press
button, the sound mode of Pro
Logic II is changed as the following order;
FL (Front Left) → C (Center) → FR (Front Right) →
SR (Surround Right) → SL (Surround Left) →
SW (Subwoofer) → FL (Front Left)
• On the 2 channel stereo mode, you can only select
the SW (Subwoofer).
PROLOGIC → MOVIE → MUSIC → VIRTUAL → MATRIX
Tip
You can select SURROUND OFF (2CH STEREO) mode by
pressing BY-PASS button.
When DVD is inserted.
v/V
V to adjust the sound level of the
3 Press
selected channel. (-6dB ~ +6dB)
step 2-3 and adjust the sound level of
4 Repeat
the other channels.
5 If setting is complete, press LEVEL.
You can change the sound mode of DVD (Dolby Digital, DTS,
PRO LOGIC, etc) by pressing the AUDIO button on the remote
during playback.
Although the DVD contents differ from disc to disc, the following explains the basic operation when this feature is used.
Test Tone
Each time you press AUDIO button, the sound mode of DVD is
changed as the following order;
This function allows you can easily adjust the sound
balance of the speakers from the listener's position.
→
→
and
When DVD is inserted and PROLOGIC II
indicator lights.
Each time you press
button, the sound mode of Pro
Logic II is changed as the following order;
PROLOGIC → MOVIE → MUSIC → VIRTUAL → MATRIX
Select the test tone mode by pressing TEST
TONE.
• A hiss noise comes out for 2 seconds from each speakers in the following order;
FL (Front Left) → C (Center) → FR (Front Right) →
SR (Surround Right) → SL (Surround Left) →
SW (Subwoofer) → FL (Front Left)
can adjust the sound level during operating
2 You
the test tone, first press LEVEL then press v/V
buttons, so that all speaker’s sound level is
same from the listener’s position.
Tip
You can set PRO LOGIC II mode to Off (2CH STEREO) by
pressing BY PASS button and the PROLOGIC II indicator disappears.
For your reference
• The DVD Receiver memorizes the last mode settings for each source individually.
• You can identify the encoding format of program
software by looking at its packaging.
- Dolby Digital discs are labeled with the
logo.
- Dolby Surround encoded programs are labeled with
the
logo.
- DTS Digital Surround discs are marked with DTS.
16
• During operating the test tone, if you adjust the sound
level, it will be paused in the current speaker channel.
3 If setting is complete, press TEST TONE.
Delay Time Setting
In Dolby Digital or Dolby Pro Logic mode it is assumed
that the distance from the listener to each of the speakers is equal. If not then setting the delay times of the
center or rear speakers the sound will be heard simultaneously by the listener.
The interval from the speakers to the listener. If the distance from the listener to each speakers is same, in the
Dolby Digital and Dolby Pro Logic mode the delay time
of each speakers is as following.
In Dolby Digital mode
Center delay time : 0ms
Rear delay time: 5ms
In Dolby Pro Logic mode
Center delay time : cannot setting
Rear delay time : 15-30ms
If the rear delay time is set in Dolby Digital mode, in the
Dolby Pro Logic mode the delay time will be automatically set.
The delay time is 1 msec per 30 cm.
If the center and rear speakers are further than the front
speakers from the listener, the delay time will be at minimum.
Ex) If the distance from the front speakers to the listener is 3m and from the center speaker to the listener is
2.4m, the center delay time is 2msec.
3m (DF) - 2.4m (DC) = 60cm (A)
60cm (A) / 30cm = 2msec
Setting the delay time in the Dolby
Digital and Dolby Pro Logic (II) mode
Press DELAY.
The current surround delay time appears in the display window.
You can select center delay time by pressing b/B in
the Dolby Digital mode only.
2 Press v/VV to change the delay time.
3 If setting is complete, press DELAY.
Notes
You can adjust the center delay time only in the Dolby Digital
mode and its delay time appears.
Surround delay time setting
Center Width
If the distance of DS is equal to or longer than the DF in
the left figure, set the Surround Delay Time as 0ms.
Otherwise, change the setting according to the below.
Ex) If the distance from front speakers to the listener is
This control allows center-channel sounds to be positioned between the center speaker and the left/right
speakers over a range of eight steps. Step “3” uses a
combination of all three front speakers to give the best
vocal imaging and most seamless soundstage presentation, and is recommended for most recordings. Step
“0” places all center sound in the center speaker. Step
“7” places all center sound equally in the left/right
speakers, just as in conventional stereo.
(A)
DC
DF
SW
DS
SL
SR
(B)
3 m and from rear speakers from the listener is 1.5 m,
in the Dolby Digital mode the rear delay time is 5 msec.
3m (DF) - 1.5m (DS) = 1.5m (B)
1.5m (B) = 150cm / 30cm = 5msec
In Dolby Pro Logic II (Surround delay time):
PROROGIC: 10 ~ 25msec
 MOVIE: 10 ~ 25msec
 MUSIC: 0 ~ 15msec
 VIRTUAL: cannot setting
 MATRIX: 0 ~ 15msec
Center delay time setting
(Dolby Digital mode only)
DIMENSE
(MUSIC mode of Dolby Pro Logic II only)
(MUSIC mode of Dolby Pro Logic II only)
This control allows the user to gradually adjust the
soundfield either towards the front or the rear. This can
be useful to help achieve the desired balance from all
the speakers with certain recordings that may contain
either too much or too little spatial effect. Step “0” is the
recommended setting, which has no effect on the
sound. Steps 1, 2, and 3 gradually move the sound forward, and steps –1, –2, and –3 move the sound
towards the surrounds.
PANORAMA (MUSIC mode of Dolby Pro Logic II only)
This control extends the front stereo image to include
the surround speakers for an exciting “wraparound”
effect with side-wall imaging. It is particularly effective
for recordings which have strong left- or right-channel
elements in the mix, as these are detected and accentuated by the Panorama process.
If the distance of DF is equal to the distance of DC in
the left figure, set the Center Delay Time as 0ms.
Otherwise, change the setting according to the table
below.
17
PREPARATION
Before Operation (Cont’d)
Before Operation - VCR Part
On-Screen Display (OSD)
Setting the On-Screen Display
Some of these functions will be displayed every time the
VCR is operated.
The SETUP, clock setting, and timer recordings are
accessed conveniently with On-Screen Menu Displays
that lead you through each step. The following pages
describe the On-screen selections to be set.
❶
❷
❸
PLAY HI-FI
SP
❹
❺
CH 4
STEREO
Menu Selection
Your VCR allows remote control adjustment of several
features.
Press MENU and the MAIN menu will appear.
JUL 5 , FRI
Select the desired menu with v/V button and
2 then
press SELECT/ENTER.
2:15 PM
❻
❶ TAPE SPEED DISPLAY
❼
Shows the current tape speed.
❷ FUNCTION DISPLAY
Note
Indicates the function in progress.
Menus remain on-screen for 3 minutes.
❸ HI-FI DISPLAY
Indicates when this unit is playing back tape recorded with
Hi-Fi.
❹ CHANNEL DISPLAY
MONTH : JANUARY
DAY
: 1 TUE
YEAR : 2002
TIME
: 12 : 00 AM
AUTO CLOCK SET: ON
PBS CH. :
TV
Indicates the selected channel (or LINE1, LINE2).
❺ STEREO/SAP DISPLAY (MONO is not displayed)
Shows the type of audio signal received by the VCR tuner.
SELECT
ADJUST
TO EXIT PRESS
❻ DATE DISPLAY
Shows the current date. (Month/Date/Day of the week
format)
SET CLOCK (page 20)
❼ CLOCK/COUNT/REMAIN DISPLAY
PROGRAM 1
MONTH :
DAY
START
STOP
CHANNEL :
SPEED :
REPEAT :
Shows the current time, the tape counter and remaining time
on the tape.
Each press of the SELECT/ENTER changes the TV
screen in the following sequence.
One press
STOP
SP
Two presses
CH 4
STOP
SP
CH 4
Three presses
STOP
SP
CH 4
SELECT
ADJUST
TO EXIT PRESS
MAIN MENU
SET CLOCK
TIMER RECORD
CHANNEL SETUP
JUL 05 , FRI
2:15 PM
After 3 seconds
M 0:35:40
After 3 seconds
REM 1:56
TIMER RECORD (page 25)
AUTO CHANNEL SEARCH
CHANNEL SOURCE:
ADD/DEL CH:
INPUT SLECT:
VCR SETUP
After 3 seconds
SELECT
ENTER
TO EXIT PRESS
2:15 PM
M 0:35:40
REM 1:56
Press
SELECT/ENTER
Press
SELECT/ENTER
Press
SELECT/ENTER
All indicators are turned off.
CHANNEL SETUP (page 19)
SCREEN DISPLAY:
LANGUAGE:
AUDIO MODE:
BROADCAST TYPE:
AUDIO OUTPUT:
ON
SELECT
ADJUST
TO EXIT PRESS
VCR SETUP (page 19)
Notes
The function displays can be seen displayed on the TV
screen for 3 seconds.
The clock (or tape counter, tape remaining) mode will continue until you press SELECT/ENTER.
The tape counter and the remaining tape length indicator
appear only when a cassette is inserted. Also, the remaining
tape length indicator appears after any tape operation.
18
Setting the VCR Setup Menu
Channel Selection
1 Press MENU and the MAIN menu will appear.
v/V
V to select the VCR SETUP menu, then
2 Press
press SELECT/ENTER.
The VCR SETUP menu will appear.
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Preparation:
SET CLOCK
TIMER RECORD
CHANNEL SETUP
VCR SETUP
SELECT
ENTER
TO EXIT PRESS
SCREEN DISPLAY:
LANGUAGE:
AUDIO MODE:
BROADCAST TYPE:
AUDIO OUTPUT:
ON
SELECT
ADJUST
TO EXIT PRESS
v/V
V to choose a desired option on the
3 Press
B to choose a
VCR SETUP menu. Then press b/B
desired setting.
Connect the DVD+VCR to the desired type of antenna or
cable TV system, as shown in Connecting Antenna/Cable TV
to DVD+VCR on page 11.
AUTO CHANNEL PROGRAMMING
1 Press MENU and the MAIN menu will appear.
v/V
V to select the CHANNEL SETUP menu,
2 Press
then press SELECT/ENTER.
The CHANNEL SETUP menu will appear.
SET CLOCK
SCREEN DISPLAY
TIMER RECORD
The on-screen display of this DVD+VCR can be turned on or off.
 SCREEN DISPLAY can be switched between ON and OFF
by pressing b/B.
CHANNEL SETUP
AUTO CHANNEL SEARCH
CHANNEL SOURCE:
ADD/DEL CH:
INPUT SLECT:
VCR SETUP
SELECT
ENTER
TO EXIT PRESS
LANGUAGE
The on-screen programming of this DVD+VCR can be
displayed in English, Spanish, or French.
 LANGUAGE can be switched among ENGLISH, SPANISH
and FRENCH by pressing b/B.
AUDIO MODE
The DVD+VCR has two separate audio playback systems, the
high quality VHS Hi-Fi system and standard NORMAL mono
system. The same audio is generally recorded on both
systems. The VHS Hi-Fi system plays on separate (left and
right) channels, and the NORMAL system plays monaural
sound. The normal track is always played so the cassette can
be played on a DVD+VCR that does not have VHS Hi-Fi.
 AUDIO MODE can be switched between HI-FI and
NORMAL by pressing b/B.
V to choose the INPUT SELECT option,
3 Press
B to select TUNER.
then press b/B
Press b/B repeatedly to switch among TUNER, LINE1
and LINE2.
v/V
V to choose the AUTO CHANNEL SEARCH
4 Press
B to find channels.
option, then press b/B
The tuner will automatically cycle through all
available channels in the area and place them in
the tuner’s memory.
the AUTO CHANNEL SEARCH PROCEED5 After
ING is complete, make sure the CHANNEL
SOURCE is set appropriately (TV or CATV) by
BROADCAST TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display to
the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is received, the
DVD+VCR automatically selects the corresponding receiving
mode (Stereo or SAP) regardless of the selected position. For
normal operation, the display should be in the STEREO position.
The DVD+VCR will then record a STEREO program when available,
and record a mono program IF the program is NOT IN STEREO.
For weak STEREO and/or SAP broadcasts, changing the display to mono may give clearer sound.
 BROADCAST TYPE can be switched among STEREO, SAP,
and MONO by pressing b/B.
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE (HI-FI/NORMAL) is
in HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RF.OUT.
This display setting should normally be left in the stereo position, so that when a stereo tape is played, the stereo sound will
be heard through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
 AUDIO OUTPUT can be switched among STEREO, LEFT,
and RIGHT by pressing b/B.
V and choosing the correct CHANpressing v/V
NEL SOURCE (TV or CATV) by pressing b/B
using the CHANNEL SETUP menu.
Remember, TV is for the air antenna reception,
CATV is for cable or wireless cable connection.
6 Press MENU to return to the TV screen.
v/V
V) or CHANNEL (v
v/V
V) on the
CH/TRK (v
7 Use
front panel to cycle the DVD+VCR through the
channels in memory.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from
memory manually.
Press V to choose the ADD/DEL CH option on the
CHANNEL SETUP menu. Press b/B to select a
channel to add or erase.
Press SELECT/ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
Press MENU to return to the TV screen.
19
PREPARATION
Before Operation - VCR Part (Continued)
Before Operation - VCR Part (Continued)
Setting the Clock
Manual Clock Set
The DVD+VCR gives you two ways to set the time and
date: the Auto Clock Feature or manually. The Auto
Clock Feature enables the DVD+VCR to set up the clock
when the DVD+VCR is turned off.
Example: July 5, 2002 ; 2:15 AM
Things to know before starting
The clock uses the 12-hour system. (Be sure to set AM
and PM correctly.)
The initial Clock Setting is JANUARY 1, 2002, 12:00 AM.
1 Press MENU and the MAIN menu will appear.
v/V
V to choose the SET CLOCK menu.
2 Press
Press SELECT/ENTER and the SET CLOCK
menu will appear.
SET CLOCK
TIMER RECORD
CHANNEL SETUP
VCR SETUP
Auto Clock Set
SELECT
ENTER
TO EXIT PRESS
The Auto Clock Set feature is set to ON at the factory. In the
ON setting, the DVD+VCR looks for a channel carrying XDS
(Extended Data Services) information. XDS updates the clock
using the Coordinated Universal Time.
The Auto Clock Feature enables the DVD+VCR to set up
the clock when the DVD+VCR is turned off.
Press MENU and the MAIN menu will appear.
v/V
V to choose the SET CLOCK menu.
2 Press
Press SELECT/ENTER and the SET CLOCK
menu will appear.
SET CLOCK
MONTH : JANUARY
DAY
: 1 TUE
YEAR : 2002
TIME
: 12 : 00 AM
AUTO CLOCK SET: ON
PBS CH. :
TV
TIMER RECORD
CHANNEL SETUP
VCR SETUP
SELECT
ENTER
TO EXIT PRESS
SELECT
ADJUST
TO EXIT PRESS
V to choose the AUTO CLOCK SET
3 Press
option.
B to choose ON.
Press b/B
The Auto Clock Set feature is set to ON at the factory. In
the ON setting, the DVD+VCR looks for a channel
carrying XDS (Extended Data Services) information. XDS
updates the clock using the Coordinated Universal Time.
V to choose the PBS CH. option.
4 Press
B to choose channel of PBS
Press b/B
broadcast.
Press MENU when finished.
Note
There are cases where the TV station does not send, or sends
wrong date and/or time information and the DVD+VCR sets the
incorrect time.
If this happens, we recommend that you set the clock manually.
20
MONTH : JANUARY
DAY
: 1 TUE
YEAR : 2002
TIME
: 12 : 00 AM
AUTO CLOCK SET: ON
PBS CH. :
TV
SELECT
ADJUST
TO EXIT PRESS
3 Press b/BB to choose the month.
V to choose the DAY option.
4 Press
B to choose the day.
Use b/B
The day of the week will display automatically.
V to choose the YEAR option.
5 Press
B to choose the year.
Use b/B
to choose the TIME option.
6 Press
B to choose the time.
Use b/B
7 Press MENU when finished.
Note
If setting the clock manually, “AUTO CLOCK SET” must
set to “OFF”.
If set to “ON”, an incorrect date and/or time will be
entered again when the DVD+VCR is turned off.
Before Operation - DVD Part
1 or 2 to change the setting of an item.
3 Press
The number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
press SELECT/ENTER to execute the setting.
Temporary Feedback Field Icons
General Explanation
This manual gives basic instructions for operating the
DVD+VCR. Some DVDs require specific operation or
allow only limited operation during playback. When this
occurs, the symbol
appears on the TV screen, indicating that the operation is not permitted by the
DVD+VCR or is not available on the disc.
TITLE
Repeat Chapter
TRACK
Repeat Track (non-PBC Video CDs only)
ALL
On-Screen Display
OFF
Repeat A-B
Repeat Off
Action prohibited or not available
On-screen display operation
3 or 4 to select an item.
2 Press
The selected item will be highlighted.
Repeat All Tracks (non-PBC Video CDs only)
Resume play from this point
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
Press DISPLAY during playback.
Repeat Title
CHAPT
Notes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
DVD
Items
Title Number
1/3
Chapter Number
Time search
Audio language
and Digital Audio
Output mode
Subtitle language
Angle
0:16:57
1 ENG
6 CH
OFF
1/1
Sound
VCD2.0
1/12
NORM.
Selection Method
Shows the current title number and total number of
titles, and skips to the desired title number.
1 / 2, or
Numbers, SELECT/ENTER
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
1 / 2, or
Numbers , SELECT/ENTER
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
Numbers , SELECT/ENTER
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
1 /2
1 /2
Shows the current angle number and total number of
angles, and changes the angle number.
1 /2
Shows the current sound mode, and
changes the setting.
1 /2
VCD1.1
Items
Track Number
1/4
Time
Audio Channel
Sound
4 to select desired item)
Function (Press 3/4
0:16:57
4 to select desired item)
Function (Press 3/4
Selection Method
Shows the current track number, total number of tracks
and PBC On mode, and skip to the desired track number.
1 / 2, or
Numeric, SELECT/ENTER
Shows the elapsed playing time (Display only)
–
STER.
Shows the audio channel, and
changes the audio channel.
1 /2
NORM.
Shows the current sound mode, and
changes the setting.
1 /2
21
PREPARATION
Caution:
Before using the remote control, press the DVD or TV
button to select the device to be operated.
Before Operation - DVD Part (Continued)
Initial Settings
Disc Audio
Off
Disc Subtitle
On
Disc Menu
You can set your own Personal Preferences on the
player.
Rating
Country Code
TV Aspect
Initial Settings General Operation
Press SETUP.
The setup menu appears.
3/4
4 to select the desired item.
2 Press
The screen will show the current setting for the
selected item, as well as alternate setting(s).
the desired item is selected, press 2, then
3 While
3/4
4 to select the desired setting.
SELECT/ENTER to confirm your selection.
4 Press
Some items require additional steps.
H) to exit the
Press SETUP, RETURN, or PLAY (H
5 setup
menu.
Language
Menu Language
Progressive Scan
PBC
Picture
TV Aspect
DVD
4:3 Letterbox: Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
16:9 Wide: Select when a 16:9 wide TV is connected.
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Rating
Disc Language
Country Code
DVD
TV Aspect
Select a language for the disc’s Menu, Audio, and Subtitle.
Original : The original language set for the disc is selected.
Other : To select another language, press number buttons to
enter the corresponding 4-digit number according to the language code list on page 39. If you enter the wrong language
code, press CLEAR.
Progressive Scan
DVD
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks, but are connecting the
DVD Player to a standard (analog) television, set
Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Country Code
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
PBC
Hungarian
Disc Audio
Off
Russian
Disc Subtitle
On
Other — — — —
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Menu Language
Select a language for the setup menu. This is the menu
you see when you press SETUP.
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Rating
Country Code
TV Aspect
Menu Language
PBC
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to the PBC.
Off: Video CDs with PBC are played the same way as Audio
CDs.
22
Progressive Scan
Notes
– Progressive Scan only works when the VIDEO OUTPUT switch on the rear panel is set to COMPONENT/PROGRESSIVE SCAN.
Caution
Once the setting for progressive scan output is entered,
an image will only be visible on a progressive scan
compatible TV or monitor. If you set Progressive Scan
to On in error, you must reset the unit. Press STOP (x)
to stop any disc that is playing. Next, press STOP (x)
again and hold it for five seconds before releasing it.
The video output will be restored to the standard setting, and a picture will once again be visible on a conventional analog TV or monitor.
Before Operation - DVD Part (Continued)
Parental Control
Country Code
Rating
Enter the code of a country/area whose standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 40.).
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are
country-dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
Disc Audio
Disc Subtitle
Code Set
U S
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Disc Audio
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
Unlock
5.1 Speaker Setup
Change
Others
“Rating” on the Setup menu using the
1 Select
3 and 4 buttons.
2 While “Rating” is selected, press 2.
you have not entered a password yet.
3 When
Enter a 4-digit password using the numbered buttons to create a personal 4-digit security password,
then press SELECT/ENTER. Enter the 4-digit password again and press SELECT/ENTER to verify.
When you have already entered a password;
Enter a 4-digit password using the numbered buttons to confirm the personal 4-digit security password, then press SELECT/ENTER.
If you make a mistake before pressing SELECT/ENTER,
press CLEAR and enter 4-digit security password again.
4 butSelect a rating from 1 to 8 using the 3/4
4 tons.
One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the player, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
SELECT/ENTER to confirm your rating
5 Press
selection, then press SETUP to exit the menu.
Others
4 buttons on
Select Country Code using the 3/4
1 the
setup menu.
2 While Country Code is selected, press 2.
3 Follow step 3 of “Rating” on left.
4 Select the first character using the 3/44 buttons.
the cursor using 1/2 buttons and select
5 Shift
4 buttons.
the second character using 3/4
SELECT/ENTER to confirm your country
6 Press
code selection, then press SETUP to exit the
menu.
Note
Confirmation of the 4-digit password is necessary when
the code is changed (see “Changing the 4-digit code”
below ).
Changing the 4-digit code
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old code, then press SELECT/ENTER.
4 buttons then press
3 Select Change using the 3/4
SELECT/ENTER.
4 Enter the new 4-digit code, then press
SELECT/ENTER.
5 Enter exactly the same code a second time and verify by pressing SELECT/ENTER.
6 Press SETUP to exit the menu.
If you forget your 4-digit code
If you forget your password, to clear the current password, follow the procedure below.
1 Press SETUP to display the setup menu.
2 Use the Number buttons to enter the 6-digit number
“210499”.
The 4-digit password is cleared. “P CLr” appears on the display. The message will appear if the disc tray is closed. It
will be on the display until you try another feature.
3 Enter a new code as shown above to the left (Rating).
23
PREPARATION
DVD
DVD
Operation with tape - VCR Part
Normal Playback
Search
Preparation:
This function lets you quickly and visually search for a
desired tape section in either direction: forward and
reverse.
Turn on the TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Set the Output Source to VCR as shown in Setting the
Output Source on page 6.
The
indicator will light and the DVD+VCR will
power-up automatically.
 Make sure that the TIMER indicator in the display
window is not lighted. If it is, press POWER once.
 If a tape without a safety tab is inserted, the unit will
start playback automatically.
H) once.
Press PLAY (H
PLAY appears on the TV screen .
It is not necessary to select the tape speed for playback. It will be automatically selected by the DVD+VCR.
In playback, the TV/VCR selector switches to VCR
mode automatically.
x) to stop playback.
Press STOP (x
STOP appears on the TV screen.
If the tape reaches the end before STOP (x) is
pressed, the DVD+VCR will automatically stop, rewind,
eject, and it will turn itself off.
Tracking Control
Auto Tracking
The automatic tracking function adjusts the picture to
remove snow or streaks.
The AUTO TRACKING function works in the following
cases:
A tape is played back for the first time.
Tape speed (SP, LP, EP) changes.
Streaks or snow appear because of scratches on the tape.
Manual Tracking
If noise appears on the screen during playback, press
v/V
V) on the remote control or
either CH/TRK (v
v/V
V) on the front panel until the noise on
CHANNEL (v
the screen is reduced.
In case of vertical jitter, adjust these controls very carefully.
Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3 seconds.
Special Effect Playbacks
Special effects playback notes
Insert a prerecorded video cassette.
1 Press BACKWARD (.) or FORWARD (>)
during playback.
The DVD+VCR will be activated in the SEARCH
mode.
Horizontal lines (noise bars) will appear on the TV screen. This
is normal.
The audio is automatically muted during special effect modes,
so there is no sound during search.
During the high-speed picture search modes, a short period is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this period.
24
If the DVD+VCR is left in the SEARCH mode for more
than 3 minutes, the DVD+VCR will automatically enter the
PLAY mode, to protect the tape and video heads.
2 To return to playback, press PLAY (H).
Still Picture and Frame-by-Frame Playback
1 Press PAUSE/STEP (X) during playback.
Still picture will appear on the TV screen.
If a still picture vibrates vertically, stabilize it by pressing
CH/TRK (v/V) on the remote control.
If the DVD+VCR is left in the STILL mode for more than 5
minutes, the DVD+VCR will automatically enter the STOP
mode to protect the tape and video heads.
2 Press PAUSE/STEP (X) repeatedly to advance the
video picture one frame at a time while viewing a still
picture.
3 To return to playback, press PLAY (H).
Slow Motion
1 While in still mode, press FORWARD (>).
The tape will be played back at a speed 1/19 times
slower than the normal speed.
During slow playback, use CH/TRK (v/V) on the Remote
Control to minimize noise bands.
If slow motion mode continues for more than 30 seconds,
the DVD+VCR will automatically change to playback
mode.
2 To return to playback, press PLAY (H).
CM SKIP (Commercial Skip)
This is useful for skipping commercials or short program
segments.
1 Press CM SKIP during the playback mode.
The tape will fast forward picture search through 30
seconds of recording.
The skipping time can be extended by pressing CM SKIP.
Subsequent presses result in advancing the fast forward
picture search time by 30-second increments (maximum 2
minutes).
2 When the search is completed, the DVD+VCR will go
into playback mode automatically.
Normal Recording
Timer Recording
Preparation:
This DVD+VCR can be programmed to record up to 8
programs within a period of 1 year. For unattended
recording, the timer needs to know the channels to be
recorded and the starting and ending times.
Turn on the power of both the DVD+VCR and TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to
VIDEO.
Things to know before starting
1 Insert a video cassette that the safety tab intact.
the desired channel by using CH/TRK
2 Select
v/V
V).
(v
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2 by pressing INPUT.
Set the desired recording speed (SP or EP) by
pressing SPEED.
This DVD+VCR is not designed to record in LP mode.
If you try to set the program timer before setting the clock,
PLEASE SET THE CLOCK appears for a moment and
then SET CLOCK menu appears on the TV screen. Set the
time and date before proceeding.
Make sure a tape is in the DVD+VCR and the safety tab is
in place or the tape will be automatically ejected.
Preparation:
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is set to the DVD+VCR output channel (3 or 4).
Make sure the CHANNEL SOURCE in the CHANNEL
SETUP menu is set appropriately (TV or CATV).
4 Set the MTS mode as desired (See page 19, 28). 1 Press MENU and the MAIN menu will appear.
z) once.
Press REC/ITR (z
5 Recording
will start. (The REC indicator will light in
2 Use v/VV to choose the TIMER RECORD menu.
the display window.)
Press SELECT/ENTER to go to the TIMER
RECORD menu.
x) to stop recording.
Press STOP (x
The TIMER RECORD menu will appear.
If a cassette with no safety tab is loaded, the cassette
will be ejected automatically.
If the tape reaches the end before STOP ( ) is pressed,
the DVD+VCR will automatically stop, rewind, eject, and
turn itself off.
If all programs have already been entered, MAX
NUMBER OF EVENTS SCHEDULED message will
appear for a moment and then PROGRAM 1 will
appear on the TV screen.
To pause the recording
1 Press PAUSE/STEP (X) to pause the tape during
recording.
The REC indicator will flash in the display window.
2 When you want to continue recording, press
z).
PAUSE/STEP (X) or press REC/ITR (z
After 5 minutes in pause mode, the tape will be stopped
automatically to protect the tape and the video heads.
To record one TV program while
watching another
1 Press TV/VCR to select the TV mode during recording.
The VCR indicator disappears.
2 Using the TV, select the channel to be viewed.
Tips
Always use PAUSE/STEP (X) for best results when making
changes during recording.
For example: To change channels during recording, first press
PAUSE/STEP (X) to put the unit in pause mode. Then select
the desired channel on the DVD+VCR, and press
PAUSE/STEP (X) again to resume recording.
SET CLOCK
TIMER RECORD
CHANNEL SETUP
VCR SETUP
SELECT
ENTER
TO EXIT PRESS
PROGRAM 1
MONTH :
DAY
START
STOP
CHANNEL :
SPEED :
REPEAT :
SELECT
ADJUST
TO EXIT PRESS
4 Use b/BB to choose the PROGRAM No. (1-8).
V to choose the MONTH option.
5 Use
B to choose the desired month.
Use b/B
Use V to choose the DAY option.
6 Use b/BB to choose the desired day.
V to choose the START option.
7 Use
B to choose the desired start time.
Use b/B
V to choose the STOP option.
8 Use
B to choose the desired stop time.
Use b/B
Use V to choose the CHANNEL option.
9 Use b/BB to choose the desired channel
(Channel, LINE1 or LINE2).
Cable Users: If you have CABLE TV and used Cable Box
in Connecting Antenna/Cable TV to DVD+VCR (page 11),
using a cable box converter, you must set the channel in
this step to match the cable box output channel (usually
CH 3 or 4). Change channels on the cable box instead of
with the DVD+VCR.
25
OPERATION
Operation with tape - VCR Part (Continued)
Operation with tape - VCR Part (Continued)
10
Use V to choose theSPEED option.
B to choose the desired recording
Use b/B
speed (AUTO, SP or EP).
11
AUTO mode determines how much tape is left and
switches speed from SP to EP, if necessary, to complete recording the program. There will be some picture and sound distortion at the point of the speed
change.
Use V to choose the REPEAT option.
B to choose the desired repeat (ONCE,
Use b/B
WEEKLY, or DAILY).
ONCE event....for recording up to 8 programs on a
single day or over the days within a period of 1 year.
WEEKLY event....for recording up to 8 programs on a
certain day of every week.
DAILY event....for recording up to 8 programs at the
same time(s) Monday through Friday.
PROGRAM 1
MONTH :
DAY
START
STOP
CHANNEL :
SPEED :
REPEAT :
JULY
6 SAT
6 : 00 PM
7 : 30 PM
4 TV
SP
ONCE
SELECT
ADJUST
TO EXIT PRESS
Tip
If the input data is wrong, use v to select the data
B.
and correct it using b/B
12
Press MENU, the program will be memorized
at the DVD+VCR.
If the program preset time is past, the EVENT
SCHEDULED IN THE PAST message will appear on
the TV screen. Return to the incorrect program and
program it with the correct time.
If you enter a past date, the timer recording will be
performed on that date of the next year.
Additional programs may be entered by repeating
steps 1-12.
Cable Users: If your cable hookup is via a TV converter box, you can program multiple recordings only on
the converter box output channel. This is because the
converter determines what channel you view through
your DVD+VCR.
13
Turn the DVD+VCR off for timer recording to
take place.
Tip
If you are finished programming and you want to set the
DVD+VCR to record the programs you have entered.
A) MAKE SURE YOU HAVE INSERTED A TAPE INTO THE
DVD+VCR. B) YOU MUST TURN OFF THE DVD+VCR
BEFORE IT WILL RECORD ANY TIMER PROGRAMS.
(TIMER indicator lights). The DVD+VCR is now set to record
the preset programs.
Note
If the power fails or the DVD+VCR is unplugged from the AC
outlet, the correct clock time and timer settings are kept in
memory for approximately 3 seconds. After 3 seconds, the
clock and program timer must be reset when power is
restored. Reset the clock according to instructions.
26
Checking (Erasing) the Timer Program
Programming can be checked whenever the DVD+VCR
is turned on.
1 Press MENU and the MAIN menu will appear.
2 Use v/V to choose the TIMER RECORD menu.
Press SELECT/ENTER and the PROGRAM menu
will appear.
SET CLOCK
TIMER RECORD
CHANNEL SETUP
VCR SETUP
SELECT
ENTER
TO EXIT PRESS
PROGRAM 1
MONTH :
DAY
START
STOP
CHANNEL :
SPEED :
REPEAT :
JULY
6 SAT
6 : 00 PM
7 : 30 PM
4 TV
SP
ONCE
TO ERASE PRESS
TO EXIT PRESS
3 Use b/B to select a program you want to check or
erase. If you want to erase the program, press
CLEAR.
4 Press MENU to return to the TV screen.
Program Priority
If the recording start and end
times of preset programs
overlap on the same day
(see the example and diagram left), program number 2
will not be recorded until program number 1 is finished.
The first part of program number 2 will not be recorded.
The same thing will happen to program number 3.
Instant Timer Recording (One-Touch Record)
Dubbing and Editing
Instant Timer Recording allows you to make a recording
easily of a preset length without using the program
timer.
If you wish to edit or dub your camcorder (or another
VCR) recordings to this DVD+VCR, the rear (or Front)
panel mounted Audio and Video (A/V) input jacks
make the connections quick and easy. These direct
A/V jacks will also provide better picture results than
using the RF jack on the rear panel.
Preparation:
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is tuned to the DVD+VCR output channel (3 or 4).
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
1 Insert a video cassette with the safety tab intact.
the desired channel by using CH/TRK
2 Select
v/V
V) or number (0-9).
(v
The channel number appears on the TV screen.
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2.
Set the desired recording speed (SP or EP) by
pressing SPEED.
The tape speed will appear on the TV screen.
z) twice.
Press REC/ITR (z
z) repeatedly to select the
Press REC/ITR (z
5 recording
time length.
At the end of the recording, the DVD+VCR will stop
The menu as illustrated, will appear on the TV screen.
 Recording will start. (The TIMER indicator will light)
the camcorder’s (or another VCR’s) A/V
1 Connect
outputs to your DVD+VCR as illustrated on page 14.
the input channel “LINE2”. (press INPUT
2 Set
twice to select LINE2.)
the tape in the camcorder (or another
3 Play
VCR). If you have a TV attached to your
DVD+VCR, you can see the video playing.
you desire recording to begin, press
4 When
z) once to start.
DVD+VCR’s REC/ITR (z
Note
Before recording, please confirm the recording start position.
Copying from DVD to VCR
This unit allows you to copy the contents of a DVD to a
VHS tape with a press of the COPY button.
recording and shut off.
During Instant Timer Recording, changing the channel
on the DVD+VCR will not be possible.
You can stop the recording by pressing STOP (x).
INSTANT TIMER RECORD (ONE-TOUCH RECORD) MENU
ONE-TOUCH RECORD
CHANNEL
SPEED
SP
START
LENGTH
NOW
0H30M
0H30M ..... 9H00M ➝ 0H00M
Length Display
(each additional press of
z) increases recording
REC/ITR (z
time 30 minutes)
Checking the Recording Time
Press REC/ITR (z) once to check the recording time.
The recalled setting will automatically return to the TV
screen after 6 seconds.
To extend the Recording Time
The recording time can be extended anytime by pressing REC/ITR (z).
Subsequent presses result in advancing the recording
time by 30-minute increments.
Notes
If you press PAUSE/STEP (X) during instant timer recording, the DVD+VCR will enter the recording pause mode.
Instant timer recording is cancelled.
If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to
normal recording mode.
If you have connected your DVD+VCR to the A/V input
jacks on the rear of DVD+VCR, you should select the
input channel LINE1 by pressing INPUT.
Note
If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc. It is not permitted to copy Macrovision encoded DVDs. “LOCK” is
displayed in the display window.
Insert Disc
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
VHS Tape
2 Insert
Insert a blank VHS video tape into the VCR deck.
the COPY button on the unit front panel.
3 Press
The DVD will go into Play mode and the VCR will
go into Record mode.
If the DVD disc menu appears, you may need to press
PLAY (H) manually to begin copying.
the Copy Process
4 Stop
When the DVD is finished playing, press the VCR
on the remote control and then press STOP (x) to
end the copy.
You must stop the Copy process manually when the
DVD movie ends, or the unit may replay and record
over and over again.
Note
When you stop the DVD playback during copying, the recording on VCR is stopped automatically.
27
OPERATION
Operation with tape - VCR Part (Continued)
Operation with tape - VCR Part (Continued)
VHS Hi-Fi Stereo System/
MTS Broadcast
MTS (Multi-Channel TV Sound)
This DVD+VCR is equipped with the VHS Hi-Fi audio
sound system for recording and playback. The information below gives a brief description of Hi-Fi audio and
how to record and play a tape in the Hi-Fi audio mode.
This DVD+VCR will decode MTS stereo and bilingual
(SAP) off-the-air broadcast sound signals. It also
decodes stereo TV sound from local cable companies,
as long as they operate on assigned cable frequencies
and use the EIA-recommended MTS stereo/bilingual TV
sound system.
Playback with Hi-Fi Stereo Audio Sound
Multichannel TV Sound Indicator (MTS)
A stereo TV with AUDIO/VIDEO input jacks or a stereo
audio system is required for true stereo playback. To
experience the full and rich stereo sound available with
Hi-Fi recorded tapes, we recommend the connection of
this unit to a home stereo audio system.
Shows Onscreen as illustrated below when
SELECT/ENTER is pressed.
Set the AUDIO MODE option to HI-FI on the VCR
SETUP menu .
SCREEN DISPLAY:
LANGUAGE:
AUDIO MODE:
BROADCAST TYPE:
AUDIO OUTPUT:
HI-FI
SELECT
ADJUST
TO EXIT PRESS
the AUDIO OUTPUT option to STEREO
2 Set
position.
(STEREO) POSITION: The left channel sound (L) is
heard from the left speaker and the right channel sound
(R) is heard from the right speaker.
(LEFT) POSITION: The left channel sound (L) is heard
from both speakers.
(RIGHT) POSITION: The right channel sound (R) is heard
from both speakers.
SCREEN DISPLAY:
LANGUAGE:
AUDIO MODE:
BROADCAST TYPE:
AUDIO OUTPUT:
STEREO
SELECT
ADJUST
TO EXIT PRESS
H).
Insert a cassette and press PLAY (H
3 Adjust
volume at your stereo system.
One or both of the indicators will light, depending on the
MTS broadcast.
TV screen
CH 4
STEREO/SAP
STEREO
Lights up when a stereo broadcast
is being received.
SAP
Lights up when a SAP BILINGUAL
broadcast is being received.
If only STEREO appears on the TV screen.
The DVD+VCR can record in stereo onto the VHS Hi-Fi audio
tracks when the BROADCAST TYPE option is in the STEREO
position. The DVD+VCR will also record mono audio onto the
mono audio track.
If only SAP appears on the TV screen.
Set the BROADCAST TYPE option to SAP.
If STEREO/SAP appears on the TV screen
Use the BROADCAST TYPE option to select the desired
recording mode (STEREO or SAP).
SAP (Second Audio Program) Recording
Some stations transmit a Second Audio Program, which
is used for a second language or additional information.
When the station broadcasts a Second Audio Program,
follow the procedure below to record the SAP.
Insert a video cassette with the safety tab intact.
the BROADCAST TYPE option to SAP (VCR
2 Set
SETUP menu).
Do this if only the SAP appears on the TV screen or you
know the program will use the SAP.
SCREEN DISPLAY:
LANGUAGE:
AUDIO MODE:
BROADCAST TYPE:
AUDIO OUTPUT:
SAP
SELECT
ADJUST
TO EXIT PRESS
the desired recording speed (SP or EP) by
3 Set
pressing SPEED.
the desired channel. The SAP should
4 Select
appear on the TV screen.
5 Press REC/ITR (zz) once
6 Press STOP (xx) to stop recording.
You are now recording the program you see and hear on the
TV.
28
Tape Counter Memory Feature
Additional Information
Real-Time Counter
In manual recording, Timer recording, Instant Timer
Recording, playback, or fast forward modes, the DVD+VCR
automatically starts rewinding the tape at the end of the
tape. The cassette will stop at the beginning of the tape and
be ejected, and the DVD+VCR will turn itself off.
After you have finished using the DVD+VCR, rewind, eject,
and remove the cassette. Place the cassette in its protective sleeve to protect it from dust. It is not necessary to
rewind the cassette before removing it, but if you do, it will
be ready to play or record the next time you use it.
Be sure the DVD+VCR Channel Selector is on the correct
channel you wish to record. The channel that is being
recorded can always be checked by setting the television
on the DVD+VCR channel (3 or 4) and pressing the
TV/VCR selector to turn the DVD+VCR’s VCR indicator on.
Do not attempt to hook up more than one television set to
the DVD+VCR for either recording or playback.
Shows length of tape run in hours, minutes, and seconds. Press CLK/CNT to select the real-time counter
display.
Every press of CLK/CNT changes the TV screen as
illustrated below.
2:15 AM
CLOCK
M 0:05:25
COUNTER
REM 1:07
REMAINING TIME
Counter changes to “M 0:00:00” when the cassette is
ejected.
The real-time counter does not operate if nothing is recorded on the tape.
The real-time counter will not work unless a tape is
inserted.
Counter Memory Function
This is useful if there is a section of tape you want to
view immediately after recording or if you want to return
to the same point several times.
Begin recording or playing a tape.
CLK/CNT repeatedly to display the real2 Press
time counter on the TV screen.
the point that you want to locate later, reset
3 Atthe
real-time counter to “M 0:00:00” by pressing
CLEAR.
Auto Play System
This DVD+VCR features automatic playback.
Load a cassette (with the safety tab removed).
The power turns on automatically and playback begins.
At the end of the tape, the DVD+VCR stops, then rewinds.
The cassette is ejected after rewinding and the unit turns
itself off automatically.
LOAD
AUTO
AUTO
PLAY
TAPE
AUTO
REWIND
EJECT
AUTO
POWER
OFF
4 Continue to play or record.
x) when recording or playback finPress STOP (x
5 ishes.
.).
BACKWARD (.
6 Press
The tape automatically stops when the tape counter
returns to about “M 0:00:00”.
Tape Remaining
This function allows the time of the remaining tape to be
displayed during recording or playback.
Press CLK/CNT until the REM indicator displays on the
TV screen during recording or playback.
Note
The remaining tape length indicator may not be displayed
correctly depending on the condition of the tape and the kind of
the tape (T-140, T-160, or T-210 etc)
29
OPERATION
Operation with tape - VCR Part (Continued)
Operation with DVD and Video CD
Playing a DVD and Video CD
Playback Setup
DVD
VCD2.0
VCD1.1
Turn on the TV and select the video input source connected to the DVD player.
Audio system: Turn on the audio system
and select the input source connected to the
DVD player.
Press OPEN/CLOSE to open the disc tray.
your chosen disc in the tray, with the label
2 Load
facing up.
When a double-sided DVD is inserted, make sure
the side you want to play is facing up.
OPEN/CLOSE to close the tray.
3 Press
READING appears on the TV screen, and playback
starts automatically. If playback does not start,
press PLAY.
In some cases, the disc menu might appear
instead.
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD or Video CD which contains a menu.
DVD
Use the 1 2 3 4 buttons to select the title/chapter
you want to view, then press SELECT/ENTER to start
playback.
Press TITLE or MENU to return to the menu screen.
VCD2.0
Use the number buttons to select the track you want
to view.
Press RETURN to return to the menu screen.
Menu setting and the exact operating procedures for
using the menu may differ depending on the disc.
Follow the instructions on the each menu screen.
You also may set PBC to Off under setup. See page
22.
Notes
– If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit code must
be entered and/or the disc must be authorized (see
“Parental Control”, on page 23).
– DVDs may have a region code.
– Your player will not play discs that have a region code
different from your player. The region code for this
player is 1 (one).
30
General Features
Note
Unless stated otherwise, all operations
described use the remote control. Some
features may also be available on the Setup menu.
Moving to another TITLE
DVD
1/3
When a disc has more than one title, you can move to
another title as follows:
 Press DISPLAY when playback is stopped, then
press the appropriate numbered button (0-9) to
select a title number.
Moving to another CHAPTER/TRACK
DVD
VCD1.1
1/12
1/3
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
 Press SKIP/SCAN . or > briefly during
playback to select the next chapter/track or to return
to the beginning of the current chapter/track.
 Press . twice briefly to step back to the previous
chapter/track.
 To go directly to any chapter during DVD playback,
4 to select C
press DISPLAY. Then, press 3/4
(chapter) (or for a Video CD, select T for track). Then,
enter the chapter/track number using the numbered
buttons (0-9).
Note
For two-digit numbers, press the buttons in rapid
succession.
Slow Motion
DVD
VCD2.0
VCD1.1
1 Press SLOW t or T during playback.
The player will enter SLOW mode.
2 Use the SLOW t or T to select the required speed:
t 1/16, t 1/8, t 1/4 or t 1/2 (backward), or T
1/16, T 1/8, T 1/4 or T 1/2 (forward).
3 To exit slow motion mode, press PLAY.
Note
Slow motion playback in reverse is not applicable for
Video CD.
Operation with DVD and Video CD - DVD Part
General Features (continued)
Video CDs - Repeat Track/All/Off
1 To repeat the track currently playing, press REPEAT.
Still Picture and Frame-by-frame playback
DVD
VCD2.0
VCD1.1
1 Press PAUSE/STEP (X) during playback.
The player will now go into PAUSE mode.
2 You can advance the picture frame-by-frame by pressing
PAUSE/STEP (X) repeatedly on the remote control.
Search
DVD
VCD2.0
VCD1.1
1 Press and hold BACKWARD (.) or FORWARD
(>) for about two seconds during playback.
The player will now go into SEARCH mode.
2 Press and hold BACKWARD (.) or FORWARD
(>) repeatedly to select the required speed: mX2,
mX4, mX16, mX100 (backward) or MX2,
MX4, MX16, MX100 (forward).
With a Video CD, the Search speed changes: mX2,
mX4, mX8 (backward) or MX2, MX4, MX8
(forward).
3 To exit SEARCH mode, press PLAY (H).
Random
The Repeat All icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Repeat function. See page 22.
Repeat A-B
DVD
VCD2.0
VCD1.1
OFF
To repeat a sequence in a title:
1 Press A-B at your chosen starting point.
A- appears briefly on the TV screen.
2 Press A-B again at your chosen end point.
A-B appears briefly on the TV screen, and the repeat sequence
begins (a-b repeat appears on the player’s display).
VCD1.1
Karaoke DVD
The Repeat Track icon appears on the TV screen.
2 To repeat the disc currently playing, press REPEAT a
second time.
3 To cancel the sequence, press A-B.
1 Press RANDOM during playback or in stop mode.
The unit automatically begins Random Playback and
“RAND.” appears on the display window.
Time Search
2 To return to normal playback, press RANDOM until
“RAND.” disappears on the display window.
The Time Search function allows you to start playing at
any chosen time on the disc.
Tips
By pressing BACKWARD (.) or FORWARD (>)
during Random playback, the unit selects another title
(track) and resumes Random playback.
Note
This function only works with DVD Karaoke discs and
video CD without PBC.
Repeat
CHAPT
DVD
TITLE
VCD2.0
TRACK
0:16:57
-:--:--
1 Press DISPLAY during playback. The on-screen display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
4 to select the Time
2 Within 10 seconds, press 3/4
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
3 Within 10 seconds, use the number buttons to enter
the required start time. Enter hours, minutes, and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
VCD1.1
ALL
DVD
OFF
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
2 To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
4 Within 10 seconds, press SELECT/ENTER to confirm
the start time.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
3D Surround
DVD
NORM.
3D SUR
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press SOUND to select “3D SUR” during playback.
2 To turn off the 3D Surround effect, press SOUND
again to select “NORM”.
31
Operation with DVD and Video CD - DVD Part (Continued)
General Features (continued)
Special DVD Features
Zoom
Checking the contents of DVD Video
discs: Menus
VCD2.0
VCD1.1
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
1 Press ZOOM during playback or still playback to activate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to six times.
2 Use the 1 2 3 4 buttons to move through the
zoomed picture.
3 Press CLEAR to resume normal playback or return to
the paused image.
Note
The zoom function may not work for some DVDs.
The zoom function may not work on multi-angle
scenes.
Marker Search
1/9
DVD
VCD2.0
DVDs may contain menus that allow you to access special features. To use the disc menu, press MENU. Then,
press the appropriate number button to select an option.
Or, use the 1/2/3/4 buttons to highlight your selection,
then press SELECT/ENTER.
Title Menu
DVD
1 Press TITLE.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3 To remove the title menu, press TITLE again.
VCD1.1
MARKER SEARCH
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when
playback reaches the spot that you want to
memorize.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
To Recall a Marked Scene
Disc Menu
DVD
1 Press MENU.
The disc menu is displayed.
2 To remove the disc menu, press MENU again.
Camera Angle
DVD
1/1
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
 Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
Changing the Audio Language
2 Within 10 seconds, press 1/2 to select a Marker number that you want to recall.
3 Press SELECT/ENTER.
Playback will start from the Marked scene.
4 To remove the MARKER SEARCH menu, press
SEARCH.
To clear a Marked Scene
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
1 ENG
6 CH
Press AUDIO repeatedly during playback to hear a different audio language or audio track.
Subtitles
DVD
1 ENG
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
2 Press 1/2 to select the Marker number that you want
to erase.
3 Press CLEAR.
DVD
If
Note
appears, the feature is not available on the disc.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
32
OPERATION
DVD
DVD
Operation with Audio CD and MP3 Discs - DVD Part (Continued)
Playing an Audio CD and MP3 discs
Search
The DVD+VCR can play MP3 formatted recordings on
CD-ROM, CD-R, or CD-RW discs.
Before playing MP3 recordings, read the notes on MP3
Recordings on page 35.
1 Press and hold BACKWARD (.) or FORWARD
(>) for about two seconds during playback.
Insert a disc and close the tray.
The menu appears on the TV screen.
CD
Program
MP3
Program
TRACK 1
TRACK 1.MP3
TRACK 2
TRACK 2.MP3
TRACK 3
TRACK 3.MP3
TRACK 4
TRACK 4.MP3
TRACK 5
TRACK 5.MP3
Clear All
TRACK 8
STER.
3 Search speed and direction are indicated on the
menu screen.
Clear All
TRACK 8.MP3
00:00
NORM.
Audio CD menu
2 Press and hold BACKWARD (.) or FORWARD
(>) repeatedly to select the required speed: mX2,
mX4, mX8 (backward) or MX2, MX4, MX8
(forward).
TRACK 7.MP3
TRACK 7
0:56:35
The player will now go into SEARCH mode.
4 To exit SEARCH mode, press PLAY (H).
TRACK 6.MP3
TRACK 6
CD
OFF
Random
CD
MP3 menu
4 to select a track then press
Press 3/4
H).
PLAY (H
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display.
Playback will stop at the end of the disc.
playback at any other time,
3 TopressstopSTOP
x).
(x
1 Press RANDOM during playback or when playback is
stopped.
The unit automatically begins Random Playback and
RANDOM or “RAND.” appears on the display window
and menu screen.
2 To return to normal playback, press RANDOM repeatedly until RANDOM or “RAND.” disappears on the
display window and menu screen.
Repeat A-B
Pause
CD
MP3
1 Press PAUSE/STEP (X) during playback.
2 To return to playback, press PLAY (H) or press
PAUSE/STEP (X) again.
CD
To repeat a sequence.
1 During disc playback, press A-B at your chosen starting point.
The Repeat icon and “A -” appears on the menu screen.
2 Press A-B again at your chosen end point.
Moving to another Track
CD
MP3
Press BACKWARD (.) or FORWARD (>) briefly
during playback to go to the next track or to return to
the beginning of the current track.
Press BACKWARD (.) twice briefly to step back to
the previous track.
In case of audio CD, to go directly to any track, enter
the track number using the numbered buttons (0-9)
during playback.
Repeat Track/All/Off
CD
MP3
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat All icon appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the menu screen.
33
The Repeat icon and “A B” appears on the menu screen,
and the sequence begins to play repeatedly.
3 To exit the sequence and return to normal play, press
A-B again.
The Repeat icon and “OFF” appear on the menu screen.
3D Surround
CD
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press SOUND to select “3D SUR” during playback.
2 To turn off the 3D Surround effect, press SOUND
again to select “NORM”.
Changing the Audio Channel
CD
Press AUDIO repeatedly during playback to hear a different audio channel (STEREO, LEFT, or RIGHT).
CD
MP3
Programmed Playback with Audio CD
and MP3 Discs
Program allows you to store your favorite tracks for a
particular disc in the player memory.
Program can contain 32 tracks (Audio CD) or 60 tracks
(MP3 disc).
1 Insert the disc and close the tray.
PROGRAM during playback or in the stop
2 Press
mode to enter the Program Edit mode.
The menu is displayed on the TV screen.
VCD2.0
VCD1.1
- DVD Part (Continued)
Programmed Playback with Video CD
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Program function. See page 22.
1 Insert Video CD and close the tray.
2 Press PROGRAM while playback is stopped.
The VCD Program menu will appear.
VCD
Program
TRACK 1
TRACK 2
The E mark will appear to the right of the word Program
on the right side of the menu screen.
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
TRACK 8
Note
Press PROGRAM to exit the Program Edit mode;
the E mark will disappear.
3/4
4 to select a track, then press
3 Press
SELECT/ENTER to place the selected track on
the Program list.
step 3 to place additional tracks on the
4 Repeat
Program list.
CD
Program
MP3
Program
TRACK 1
TRACK 12
TRACK 1.MP3
TRACK 8.MP3
TRACK 2
TRACK 8
TRACK 2.MP3
TRACK 2.MP3
TRACK 3
TRACK 10
TRACK 3.MP3
TRACK 4.MP3
TRACK 4
TRACK 3
TRACK 4.MP3
TRACK 3.MP3
TRACK 5
steps 3-7 of “Programmed Playback with
3 Follow
Audio CD and MP3 Disc” on left.
Repeat Programmed Tracks
STER.
Clear All
TRACK 8.MP3
NORM.
Audio CD menu
00:00
To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat All icon appears on the menu screen.
TRACK 7.MP3
Clear All
TRACK 8
To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
TRACK 6.MP3
TRACK 7
OFF
MP3 menu
5 Press 2.
The programmed track you selected last is highlighted on
the program list.
Note
Press RETURN or PROGRAM to exit the Program menu.
TRACK 5.MP3
TRACK 6
0:56:35
Clear All
4 to select the track you want to start
Press 3/4
playing.
Press TITLE to move to the next page.
Press MENU to move to the previous page.
To cancel Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the menu screen.
Erasing a Track from Program List
1 Press PROGRAM during playback or in the stop
mode to enter the Program Edit mode.
The
mark will appear.
2 Press 2 to move to the Program list.
4 to select the track that you wish to erase
3 Use 3/4
from the Program list.
4 Press CLEAR.
The track will be erased from the Program list.
H) to start.
Press PLAY (H
Playback begins in the order in which you programmed
the tracks and “PROG.” appears on the menu screen.
Playback stops after playing the last programmed track on
the program list.
Erasing the Complete Program List
1 Follow steps 1-2 of “Erasing a Track from Program
List” as above.
4 to select “Clear All”, then press
2 Use 3/4
SELECT/ENTER.
The complete Program for the disc will be erased.
The programs are also cleared when the disc is removed.
To resume normal playback from programmed
playback
Press and hold PROGRAM for 3 seconds until “PROG.”
indicator disappears in the display window.
34
OPERATION
Programmed Playback
Additional Information - DVD Part
Last Condition Memory
DVD
CD
Notes on MP3 Discs
VCD1.1
About MP3
This player memorizes the last condition for the last
disc you have watched. Settings remain in memory
even if you remove the disc from the player or switch off
the player. If you load a disc that has its settings memorized, the latest stop position is automatically recalled.
Notes
– Settings are stored in memory for use any time.
– This player does not memorize settings of a disc if
you switch off the player before commencing to play
it.
Screen Saver
The screen saver picture appears when you leave the
DVD+VCR in stop mode for about five minutes.
After the Screen Saver has been engaged for about five
minutes, the DVD+VCR will automatically turn itself off.
Video Mode Setting
DVD
VCD2.0
VCD1.1
With certain discs, the playback picture may be flickering or Dot Crawl is shown on straight lines. That
means Vertical interpolation or De-interlace is not
perfectly matched with the disc. In this case, the
picture quality may be improved by changing the
video mode.
To change the video mode, press and hold DISPLAY
about 3 seconds during disc playback. The new video
mode number selected is displayed on the TV screen.
Check whether the video quality has improved. If not,
repeat the above procedure until picture quality is
improved.
Video mode change sequence:
MODE1 → MODE2 → MODE3 → MODE4 →
MODE5 → MODE1
If you turn off the power, the video mode will be back
to initial state (MODE1).
An MP3 file is audio data compressed by using
MPEG1, the audio layer-3 file-coding scheme. We call
files that have the “.mp3” file extension “MP3 files”.
The player can not read an MP3 file that has a file
extension other than “.mp3”.
The player can not read a fake MP3 file that has a
file extension “.mp3”.
MP3 Disc compatibility with this player is limited as follows:
1.
2.
3.
4.
Sampling Frequency / only at 44.1kHz
Bit rate/ within 32 - 320kbps
CD-R physical format should be “ISO 9660”
If you record MP3 files using the software which
cannot create a FILE SYSTEM, for example “DirectCD” etc., it is impossible to playback MP3 files. We
therefore recommend that you use “Easy-CD
Creator”, which creates an ISO9660 file system.
5. A single session disc requires MP3 files in the first
track. If there is no MP3 file in the 1st track, it cannot playback MP3 files. If you wish to playback MP3
files, format all the data in the disc or use a new
one.
6. We do not recommend using CD-RW discs. Please
use finished CD-R discs only.
7. File names should be named using 8 letters or less
and must incorporate the “.mp3” extension
e.g. “********.MP3”.
8. Do not use special characters such as
“_?!><+*}{`[@ ]:;\/.,” etc.
9. Total number of files on the disc should be less than
200.
10. Use 74 minute CD-R discs (650M), do not use 80
minute CD-R (700M) software.
This DVD+VCR requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 files).
Customers should also note that permission is
required in order to download MP3 files and music
from the Internet. Our company has no right to
grant such permission. Permission should always
be sought from the copyright owner.
35
Presetting Radio Stations
Listening to the Radio
You can preset 30 stations for FM and AM. Before tuning, make sure that you have turned down the volume
to the minimum.
Preset radio stations in the DVD+VCR’s memory first
(see “Presetting radio stations” on the left side).
Press FUNCTION on the front panel repeatedly
or FM/AM on the remote control until FM or AM
appear in the display window.
Press FM/AM until AM or FM appears in the display window.
The last received station is tuned in.
then every time you press FM/AM, FM and
2 And
AM change alternately.
v/V
V) on the front panel
and hold TUNING (v
v/V
V) repeatedly to select a prePress PRESET (v
3 Press
for about two seconds until the frequency indi2
set
station.
cation starts to change, then release.
Scanning stops when the DVD Receiver tunes in a
station. “TUNED” and “STEREO” (for stereo program)
appear in the display window.
Each time you press the button, the DVD+VCR tunes in
one preset station at a time.
the volume by rotating VOLUME on the
3 Adjust
front panel or by pressing VOLUME + or - on the
remote control repeatedly.
ote
“Tuned” only appears when the signal is FM and
stereo.
To turn off the radio
Press MEMORY.
Press POWER to turn the DVD+VCR off or select
another function mode (DVD/CD, VIDEO 1 or VIDEO 2).
v/V
V) on the front panel to select
TUNING (v
5 Press
the preset number.
6 Press MEMORY again.
7 Repeat steps 3 to 6 to store other stations.
A preset number will flash in the display window.
To listen to non-preset radio stations
Use manual or automatic tuning in step 2.
For manual tuning, press TUNING (v/V) on the front
panel repeatedly.
For automatic tuning, press and hold TUNING (v/V)
for about two seconds on the front panel.
The station is stored.
To tune in a station with a weak signal
Press TUNING (v/V) repeatedly in step 3 to tune in the
station manually.
To clear all the memorized stations
Press and hold MEMORY for about three seconds and
“CLEAR ALL” appears in the display window and then
press MEMORY again, the stations are cleared.
For your reference
 If an FM program is noisy
Press MONO/ST. on the front panel so that
“STEREO” disappears in the display window. There
will be no stereo effect, but the reception will
improve. Press the button again to restore the stereo
effect.
To improve reception
Realign the antenna.
ote
If all stations have already been entered, FULL message will appear in the display window for a moment
and then a preset number will flash. To change the preset number, follow the steps 5-6 as above.
36
OPERATION
Operation with Radio
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Symptom
Correction
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD+VCR does not
work.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
No picture.
The TV is not set to receive DVD+VCR
signal output.
Select the appropriate video input mode
on the TV so the picture from the
DVD+VCR appears on the TV screen.
TV/VCR mode for DVD+VCR is set to
TV.
Press the TV/VCR button on the remote
control repeatedly to choose VCR
mode. VCR indicator light appears in
the display window.
The video cable is not connected
securely.
Connect the video cable securely.
The connected TV power is turned off.
Turn on the TV.
The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
The audio cables are not connected
securely.
Connect the audio cable securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The Digital Audio Output is set to the
wrong position.
Set the Digital Audio Output to the
correct position, then turn on the
DVD+VCR again by pressing POWER.
The disc is dirty.
Clean the disc.
Tape heads are dirty.
Clean video heads.
Tape is a rental or was recorded on
another VCR.
Use CH/TRK (v/V) for manual tracking
adjustment while tape is playing.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type, color system, and Regional code.)
The disc is placed upside down.
Place the disc with the playback side down.
The disc is not placed within the guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
The Rating level is set.
Cancel the Rating function or change
the rating level.
The remote control is not pointed at the
remote sensor of the DVD+VCR.
Point the remote control at the remote
sensor of the DVD+VCR.
The remote control is too far from the
DVD+VCR.
Operate the remote control within 23 ft
(7 m).
There is an obstacle in the path of the
remote control and the DVD+VCR.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
This remote control has same buttons
between VCR and DVD (ex. PLAY).
When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
No sound.
The playback picture is
poor.
The DVD+VCR does
not start playback.
The remote control
does not work properly.
37
Troubleshooting (Continued)
Cause
Correction
Some channels are
skipped over when
using CH/TRK (v/V)
Those channels were deleted with the
ADD/DEL CH. option.
Use ADD/DEL CH. to restore channels.
See “Channel Selection” on page 19.
Picture and sound of
broadcasting channel
are weak or missing.
Antenna or cables are loose.
Tighten connections or replace cable.
Wrong CHANNEL SOURCE option is
being used.
Try all CHANNEL SOURCE options.
See “Channel Selection” on page 19 for
details.
Camcorder image is not
shown.
Camcorder is off.
Turn camcorder on and operate
properly.
Camcorder image via
A/V input to DVD+VCR
is not shown on TV
screen.
DVD+VCR INPUT SELECT is not set to
LINE1 or LINE2.
Press INPUT to select LINE input channel (LINE1 or LINE2).
Timer recording is not
possible.
Clock in DVD+VCR is not set to correct
time.
Set clock to correct time. See “Setting
the Clock” on page 20.
DVD+VCR is on which disables timer.
Turn DVD+VCR off to enable timer.
TIMER indicator light appears in the
display window.
Timer has been programmed
incorrectly.
Reprogram Timer. See “Timer
Recording” on pages 25 and 26.
TIMER indicator light does not appear
after programming timer.
Reprogram Timer and turn DVD+VCR
off to enable timer.
TIMER indicator light
appears after DVD+VCR
is turned off.
DVD+VCR is in Timer Recording mode.
This is the normal indication that the
DVD+VCR is in TIMER mode.
Stereo Audio Record
and/or Playback is not
present.
TV is not Stereo-compatible.
No action is possible.
Broadcast program is not in stereo format.
No action is possible.
DVD+VCR A/V Out jacks are not connected to TV A/V In jacks.
Make A/V connections. Stereo is
available only via A/V output from
DVD+VCR.
DVD+VCR Audio/Video Out is not
selected for viewing at the TV.
Select AUX or A/V source as TV input.
DVD+VCR BROADCAST TYPE mode is
set to SAP or MONO.
Set BROADCAST TYPE mode to
STEREO. See “Setting the VCR Setup
Menu” on page 19.
Moisture Condensation
Moisture condensation can occur:
In locations where moisture condensation may occur:
• When the DVD+VCR is moved from a cold place to a
warm place.
• Keep the DVD+VCR plugged into an AC power outlet
with POWER On. This will help prevent condensation.
• Under extremely humid conditions.
• When condensation has occurred, wait a few hours
for the DVD+VCR to dry before using it.
38
REFERENCE
Symptom
Language Code List
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 22).
Code
Language
Code
Language
Code
Language
Code
Language
6566
Abkhazian
7074
Fiji
7678
Lingala
8373
Singhalese
6565
Afar
7073
Finnish
7684
Lithuanian
8375
Slovak
6570
Afrikaans
7082
French
7775
Macedonian
8376
Slovenian
8381
Albanian
7089
Frisian
7771
Malagasy
8379
Somali
6577
Amharic
7176
Galician
7783
Malay
6983
Spanish
6582
Arabic
7565
Georgian
7776
Malayalam
8385
Sudanese
7289
Armenian
6869
German
7784
Maltese
8387
Swahili
6583
Assamese
6976
Greek
7773
Maori
8386
Swedish
6588
Aymara
7576
Greenlandic
7782
Marathi
8476
Tagalog
6590
Azerbaijani
7178
Guarani
7779
Moldavian
8471
Tajik
6665
Bashkir
7185
Gujarati
7778
Mongolian
8465
Tamil
6985
Basque
7265
Hausa
7865
Nauru
8484
Tatar
6678
Bengali; Bangla
7387
Hebrew
7869
Nepali
8469
Telugu
6890
Bhutani
7273
Hindi
7879
Norwegian
8472
Thai
6672
Bihari
7285
Hungarian
7982
Oriya
6679
Tibetan
6682
Breton
7383
Icelandic
8065
Panjabi
8473
Tigrinya
6671
Bulgarian
7378
Indonesian
8083
Pashto, Pushto
8479
Tonga
7789
Burmese
7365
Interlingua
7065
Persian
8482
Turkish
6669
Byelorussian
7165
Irish
8076
Polish
8475
Turkmen
7577
Cambodian
7384
Italian
8084
Portuguese
8487
Twi
6765
Catalan
7465
Japanese
8185
Quechua
8575
Ukrainian
9072
Chinese
7487
Javanese
8277
Rhaeto-Romance
8582
Urdu
6779
Corsican
7578
Kannada
8279
Romanian
8590
Uzbek
7282
Croatian
7583
Kashmiri
8285
Russian
8673
Vietnamese
6783
Czech
7575
Kazakh
8377
Samoan
8679
Volapük
6865
Danish
7589
Kirghiz
8365
Sanskrit
6789
Welsh
7876
Dutch
7579
Korean
7168
Scots Gaelic
8779
Wolof
6978
English
7585
Kurdish
8382
Serbian
8872
Xhosa
6979
Esperanto
7679
Laothian
8372
Serbo-Croatian
7473
Yiddish
6984
Estonian
7665
Latin
8378
Shona
8979
Yoruba
7079
Faeroese
7686
Latvian, Lettish
8368
Sindhi
9085
Zulu
39
Country Code List
Code
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CS
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
Country
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaidjan
Bosnia-Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Ivory Coast
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Former Czechoslovakia
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Code
ER
ES
ET
FI
FJ
FK
FM
FO
FR
FX
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Country
Eritrea
Spain
Ethiopia
Finland
Fiji
Falkland Islands
Micronesia
Faroe Islands
France
France (European
Territory)
Gabon
Great Britain
Grenada
Georgia
French Guyana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe (French)
Equatorial Guinea
Greece
S. Georgia & S. Sandwich
Isls.
Guatemala
Guam (USA)
Guinea Bissau
Guyana
Hong Kong
Heard and McDonald
Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia6
Kiribati
Comoros
Saint Kitts & Nevis Anguilla
North Korea
South Korea
Kuwait
Cayman Islands
Kazakhstan
Laos
Lebanon
Code
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
Country
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libya
Morocco
Monaco
Moldavia
Madagascar
Marshall Islands
Macedonia
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique (French)
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia (French)
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
Polynesia (French)
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and Miquelon
Pitcairn Island
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
Saudi Arabia
Solomon Islands
Code
SC
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SU
SV
SY
SZ
TC
TD
TF
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UK
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Country
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Islands
Slovak Republic
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Saint Tome and Principe
Former USSR
El Salvador
Syria
Swaziland
Turks and Caicos Islands
Chad
French Southern
Territories
Togo
Thailand
Tadjikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania
Ukraine
Uganda
United Kingdom
USA Minor Outlying
Islands
United States
Uruguay
Uzbekistan
Vatican City State
Saint Vincent &
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (USA)
Vietnam
Vanuatu
Wallis and Futuna Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
40
REFERENCE
Enter the appropriate code number for the initial setting “Country Code” (See page 23).
Specifications
General
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Signal system
AC 120V, 60 Hz
80W
430 X 97.5 X 360 mm (16.9 x 3.9 x 14.2 inches) (w x h x d)
7 kg (15.4 lbs)
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
NTSC
Inputs
ANTENNA IN
VCR VIDEO IN
VCR AUDIO IN
FM ANTENNA IN
AM ANTENNA IN
DIIGTAL AUDIO IN
Antenna or CATV input, 75 ohms
1 Vp-p 75 ohms, sync negative, RCA jack x 1
-6.0 dBm more than 47 kohms, RCA jack (L, R) x 1
FM antenna input, 300 ohms
AM antenna input, 300 ohms
5 V (p-p), 75 Ω, Optical connector x 1
Outputs
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (analog audio)
RF OUT
1 Vp-p 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 ohms
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
2.0 Vrms (1 KHz, 0 dB), 330 ohms, RCA jack (L, R) x 1
Channel 3 or 4 (Switchable)
VCR Specifications
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Antenna
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
Four head helical scan azimuth system
12-hour display type with AM, FM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, EP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), EP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
75 ohms (VHF/UHF)
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
20Hz to 20kHz
More than 43dB
More than 83 dB
More than 55 dB
DVD Specifications
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
DVD (PCM 48 kHz): 8 Hz to 22 kHz, CD: 8 Hz to 20 kHz
More than 100dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB
41
Specifications (Continued)
Radio Tuner
87.5 - 108 MHz
10.7 MHz
60 dB
150 - 10,000 Hz
530 - 1,720 kHz
450 kHz
REFERENCE
Tuning Range
Intermediate Frequency
Signal-to Noise Ratio
Frequency Response
Tuning Range
Intermediate Frequency
Amplifier
Stereo mode
Surround mode
50W + 50W (8 Ω at 1 kHz, THD 10 %)
Front: 50W + 50W (THD 10 %)
Center*: 50W
Surround*: 50W + 50W (8Ω at 1 kHz, THD 10 %)
Subwoofer*: 80W (4Ω at 30 Hz, THD 10 %)
*Depending on the sound mode settings and the source, there may be no sound output.
Inputs
LINE 1, LINE 2, OPTICAL AUDIO
Speakers
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max. Input Power
Net Dimensions (W x H x D)
Net Weight
Satellite Speaker
2 Way 2 Speaker
8Ω
110 - 40,000 Hz
83 dB/W (1m)
50W
100 W
100 x 147 x 127.5 mm
0.92 kg
Passive Subwoofer
1 Way 1 Speaker
4Ω
40 - 1,500 Hz
82 dB/W (1m)
100 W
200 W
200 x 425 x 381 mm
7.06kg
Accessory:
S-Video cable . . . . . . . . . . . . . .1
Video cable . . . . . . . . . . . . . . .1
Audio cable . . . . . . . . . . . . . . .1
RF 75-ohm Coaxial Cable . . . .1
Speakers . . . . . . . . . . . . . . . . .6
Speaker cables . . . . . . . . . . . .5
AM loop antenna . . . . . . . . . . .1
FM antenna . . . . . . . . . . . . . . .1
Remote control . . . . . . . . . . . . .1
Batteries . . . . . . . . . . . . . . . . . .2
Design and specifications are subject to change without notice.
Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. Copyright
1992-1997 Dolby Laboratories. All rights reserved.
DTS and DTS Digital Surround are registered trademarks of
Digital Theater Systems, Inc.
42
ZENITH ELECTRONICS CORPORATION
LIMITED WARRANTY (USA)
Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or
workmanship under normal use during the warranty period listed below from the date of original
consumer purchase. This warranty is good only to the original purchaser of the product during the
warranty period as long as it is in the United States, excluding US Territories.
WARRANTY PERIOD
WARRANTY PERIOD
Labor:
90 Days from date of purchase
Parts:
One Year from the date of purchase
HOW SERVICE IS HANDLED
Carry-in service. Please retain your bill of sale for proof of
warranty.
Please call 1-877-9ZENITH (1-877-993-6484) to locate
your nearest Zenith Authorized Service Center. Please
see below for further information.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,
INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS
REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESSED WARRANTY
PERIOD ABOVE. ZENITH WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING
WITHOUT LIMITATION LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA,
OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on
how long an implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other rights that vary from state to state.
THE ABOVE WARRANTY DOES NOT APPLY TO:
1. To damages or problems that result from shipping, installation, calibration, maintenance, or separate
system components.
2. To damages or problems that result from misuse, abuse, operation outside environmental specifications or contrary to the requirements and precautions in the Operating Guide, accident, lightning
strikes or other natural causes, modification or alteration, incorrect electrical current or voltage, signal
reception or input, software not licensed directly by Zenith, software errors that do not disable functionality, operating and software protocols adopted after date of manufacturer or for outside the US,
or institutional or commercial use.
Therefore, the cost of repair or replacement is borne by the customer.
CUSTOMER ASSISTANCE NUMBERS:
To Prove Warranty Coverage:
To Obtain Where-To-Buy, nearest
Authorized Service Center, Product
Assistance, or Customer Assistance:
ZENITH ELECTRONICS CORPORATION
2000 MILLBROOK DRIVE
LINCOLNSHIRE, IL 60069
→
→
Retain your Sales Receipt to prove date of purchase.
A copy of your Sales Receipt must be submitted at the time
warranty service is provided.
Call 1-877-9ZENITH (1-877-993-6484) and choose the
appropriate prompt.
(Mon. ~ Fri. 7 a.m. ~ 8 p.m. and Sat. 8 a.m. to 5:00 p.m. CT)
or visit our website at
http://www.zenithservice.com
Zenith Part No. 206-3792
GS# 3835RM0053J
Printed in China
Issue O

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:09:02 12:31:08
Producer                        : Acrobat Distiller 4.0 for Macintosh
Author                          : ytkg4
Creator                         : QuarkXPressª 4.11: LaserWriter 8 Z1-8.7.1
Title                           : DT-587M_OM_Zenith
Modify Date                     : 2002:09:12 11:23:05-04:00
Page Count                      : 43

EXIF Metadata provided by EXIF.tools