LG Electronics USA D2542PY Part15 Subpart B-LCD Monitor User Manual BEJD2542PY 1

LG Electronics USA Part15 Subpart B-LCD Monitor BEJD2542PY 1

Contents

BEJD2542PY_User Manual 1

www.lg.comOWNER’S MANUALCINEMA 3D MONITORD2242P D2542PPlease read this manual carefully before operating your set and retain it for future reference.CINEMA 3D MONITOR MODELENGLISH
2ENGENGLISHTABLE OF CONTENTSCONTENTS3 ASSEMBLING AND PREPARING3 Unpacking4 Parts and buttons6 Setting up the Monitor set 6 - Attaching the Stand Base6 - Detaching the Stand Base and Body7 - Mounting on a table8 - Mounting on a wall10 USING THE MONITOR SET10 Connecting to a PC10 - D-SUB connection10 - DVI-D connection10 - HDMI connection12 CUSTOMIZING SETTINGS12 Accessing The Main Menus13 Customizing Settings13 - Menu Settings14 - 3D Settings(Only 3D mode)14 - Volume Settings (Only supported in HDMI)15 - SUPER ENERGY SAVING Settings16 TROUBLESHOOTING18 TROUBLESHOOTING WHEN USING 3D MODE19 SPECIFICATIONS 21 Preset Modes (Resolution)21 HDMI 3D TIMING21 Indicator22 PRECAUTIONS TO TAKE WHEN VIEWING 3D IMAGES23 PROPER POSTURE23 Proper posture for using the Monitor set.23 Precautions to take when viewing 3D im-ages
3ENGENGLISHASSEMBLING AND PREPARINGASSEMBLING AND PREPARINGUnpackingCheck your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories. yDo not use any unapproved accessories to ensure the safety and product life span. yAny damages or injuries by using unapproved accessories are not covered by the warranty. yThe accessories supplied with your product may vary depending on the model. yProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions. yUser should use shielded signal interface cables (RGB cable / DVI-D cable) with ferrite cores to maintain standard compliance for the product.CAUTIONNOTEStand BaseStand BodyPower CordCD(Owner's Manual) / CardTriDef 3D software Program CD / Quick Installation GuideD-SUB Cable(This signal cable may be attached to this product before shipping out.)DVI-D Cable(This cable is not included in all countries.)3D Glasses(Normal type)3D Glasses(Clip-on type)
4ENGENGLISHASSEMBLING AND PREPARINGParts and buttonsHDMID-SUBAC-IN/䔜㹷彺⅌ DVI-DPower Indicator yLighting On: Turned on yLighting Off: Turned offConnection panel (See p.10)Button (See p.12)(Power Button)
5ENGENGLISHASSEMBLING AND PREPARINGButton DescriptionMENU Accesses the main menus.(See p.13)OSD LOCKED/UNLOCKEDThis function allows you to lock the current control settings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear.SUPER ENERGYSAVING ButtonUse this button to enter SUPER ENERGY SAVING menu.For more information.(See p.15)3D 3D display settings.(See p.14)AUTO When adjusting your display settings, always press the AUTO button on the MONITOR SETUP OSD. (Only supported in Analog Mode)The best display mode 1920 x 1080 (D2242P/D2542P)VOLUME (Only HDMI mode) Adjust the volume of the Monitor set.(See p.14)INPUT You can choose the input signal. yWhen two input signals are at least are connected, you can select the input signal (D-SUB/DVI/HDMI) you want. yWhen only one signal is connected, it is automatically detected. The default setting is D-SUB.EXIT Exit the OSD(On Screen Display). (Power Button) Turns the power on or off.Power Indicator The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode, the power indicator blinks blue.
6ENGENGLISHASSEMBLING AND PREPARINGSetting up the Monitor set Attaching the Stand Base1 Place the Monitor set with the screen side down on a flat and cushioned surface.Lay a foam mat or soft protective cloth on the surface to protect the screen from damage. yThis illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. yDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.CAUTIONCAUTIONDetaching the Stand Base and Body1 Place the Monitor set with the screen side down on a flat and cushioned surface.2 Pull out the Stand Base and Stand Body from the Monitor set.3 Attach the Stand Base and then tighten the screw to the right with a Coin.2 Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”.3 Turn the screw to the left with a Coin, and then pull out the Stand Base from the Stand Body.Stand BodyStand BaseHinge Body
7ENGENGLISHASSEMBLING AND PREPARINGMounting on a table1 Lift and tilt the Monitor set into its upright position on a table.Leave a 10 cm (minimum) space from the wall for proper ventilation.2 Connect the Power Cord to a wall outlet.3 Press (Power) button on the front switch panel to turn the power on.10 cm10 cm10 cm10 cmWhen you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.Do not touch or press the screen when adjusting the angle of the monitor.WARNINGUnplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.Tilt from +15 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.CAUTIONNOTEFront Rear15- 5
8ENGENGLISHASSEMBLING AND PREPARINGMounting on a wallFor proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation andSetup Guide.When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.Please use VESA standard as below. y784.8 mm (30.9 inch) and under* Wall Mount Pad Thickness : 2.6 mm* Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm y787.4 mm (31.0 inch) and above* Please use VESA standard wall mount pad and screws.10 cm10 cm10 cm10 cmUsing the Kensington security system The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit http://www.kensington.com.Connect the Kensington security system cable between the Monitor set and a table.The Kensington security system is optional. You can obtain it from most electronics stores.NOTE
9ENGENGLISHASSEMBLING AND PREPARING yDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur. yIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury. yUse only an authorized LG wall mount and contact the local dealer or qualified personnel. y Do not over tighten the screws as this may cause damage to the Monitor set and void your warranty. y Use only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty. yUse the screws that are listed on the VESA standard screw specifications. yThe wall mount kit will include an installation manual and necessary parts. yThe wall mount bracket is optional. You can obtain additional accessories from your local dealer. yThe length of screws may differ depending on the wall mount. Be sure to use the proper length. yFor more information, refer to the instructions supplied with the wall mount.CAUTIONNOTEModel D2242P D2542P VESA (A x B) 75 x 75 100 x 200Standard screw M4 M4Number of screws 4 4Wall mount bracket (optional)RW120 RW120
10ENGENGLISHUSING THE MONITOR SETUSING THE MONITOR SETConnecting to a PC yYour Monitor set supports Plug & Play*. *Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.D-SUB connectionTransmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations. yMac adapterFor Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector. yWhen using a D-Sub signal input cable connector for Macintosh yIf you use HDMI PC, it can cause compatibility problem.NOTENOTEHDMID-SUBDVI-DRGB OUTHDMID-SUBDVI OUTDVI-DHDMID-SUBHDMI OUTDVI-DHDMI OUTDVI-D connectionTransmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.HDMI connectionTransmits the digital video and audio signals from your PC or A/V to the Monitor set. Connect the PC or A/V and the Monitor set with the HDMI cable as shown in the following illustrations.
11ENGENGLISHUSING THE MONITOR SET yWhen you want to use two PC in our Monitor, please connect the signal cable(D-SUB/DVI-D/HDMI) respectively in Monitor set. yIf you turn the Monitor set on while it is cold, the screen may flicker. This is normal. ySome red, green, or blue spots may appear on the screen. This is normal. y"Self Image Setting" Function.This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.(Only supported in Analog Mode) y‘AUTO’ Function.When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution.(Only supported in Analog Mode)NOTE NOTE yConnect the signal input cable and tighten it by turning the screws clockwise. yDo not press the screen with your finger for a long time as this may result in temporary distortion on the screen. yAvoid displaying a fixed image on the screen for a long period of time to prevent image burn. Use a screensaver if possible.CAUTION Self Image Setting FunctionPress the power button on the front panel to turn the power on. When monitor power is turned on, the "Self Image Setting" Function is executed automatically. (Only supported in Analog Mode)
12ENGENGLISHCUSTOMIZING SETTINGSCUSTOMIZING SETTINGSAccessing The Main Menus1 Press any button on the front of the Monitor set to display the MONITOR SETUP OSD menu.2 Press the desired menu item.3 Change the value of the menu item by pressing the buttons on the front of the Monitor set.To return to the upper menu or set other menu items, use the up arrow ( ) button.4 Select EXIT to leave the OSD menu.Monitor set ButtonsMONITOR SETUPMENU AUTO VOLUME INPUT EXIT3DMENU (See p.13)Sets the screen options.AUTO (See p.5)Optimizes the resolution.EXITExits the OSD menu.INPUTSets the external input.3D (See p.14)Sets the 3D mode.VOLUME (See p.14)Sets the volume.Different menu items are enabled depending on the type of input signal. yD-SUB / DVI Mode: MENU, 3D, AUTO, INPUT, EXIT yHDMI Mode: MENU, 3D, VOLUME, INPUT, EXITNOTE
13ENGENGLISHCUSTOMIZING SETTINGSCustomizing SettingsMenu Settings1 Press any button on the front of the Monitor set to display the MONITOR SETUP OSD menu.2 Press the MENU button to display the options in the OSD menu.3 Set the options by pressing the buttons on the front of the Monitor set.4 Select EXIT to leave the OSD menu.To return to the upper menu or set other menu items, use the up arrow ( ) button.Menu Analog Digital HDMI DescriptionBRIGHTNESS ● ● ● Adjusts the brightness of the screen.ORIGINAL RATIO● ● ●WIDESwitch to full screen mode according to input image signal.ORIGINALChange the input image signal ratio to original.* This function works only if input resolution is lower than Monitor set ratio (16:9).3D COLOR EFFECT ● ● ● The picture quality is optimized at the 3D mode.COLOR TEMP● ● ●PRESETSelect the screen color. yWARM: Set the screen to warm color temperature (more red). yMEDIUM: Set the screen to medium color temperature. yCOOL: Set the screen to cool color temperature (More blue).USER yRED: Set your own red color levels. yGREEN: Set your own green color levels. yBLUE: Set your own blue color levels.CONTRAST ● ● ● Adjusts the contrast of the screen.BLACK LEVEL(Only supported in HDMI mode) ●You can set the offset level. If you select 'HIGH', the screen will be bright and if you select ‘LOW’, the screen will be dark. yOffset: As the criteria for video signal, it is the darkest screen the monitor can show.LANGUAGE ● ● ● Changes the menu language.SUPER ENERGY SAVING ● ● ● Sets the SUPER ENERGY SAVING function.FACTORY ● ● ● Returns the monitor to original factory settings. yAnalog: D-SUB(Analog signal) input. yDigital: DVI-D(Digital signal) input. yHDMI: HDMI(Digital signal) input. MENUEXITBRIGHTNESSORIGINAL RATIO3D COLOR EFFECTCOLOR TEMPPRESETREDGREENBLUECONTRASTBLACK LEVELLANGUAGESUPER ENEYGY SAVINGFACTORY RESETWIDEOFFPRESETWARMHIGHENGLISHNOThe available program settings are described below.10050505070
14ENGENGLISHCUSTOMIZING SETTINGS3D Settings(Only 3D mode)1 Press any button on the front of the Monitor set to display the MONITOR SETUP OSD menu.2 Press the 3D button to display the options in the OSD menu.3 Set the options by pressing the buttons on the front of the Monitor set.4 Select EXIT to leave the OSD menu.To return to the upper menu or set other menu items, use the up arrow ( ) button. Volume Settings (Only supported in HDMI)1 Press any button on the front of the Monitor set to display the MONITOR SETUP OSD menu.2 Press the VOLUME button to display the options in the OSD menu.3 Set the options by pressing the buttons on the front of the Monitor set.4 Select EXIT to leave the OSD menu.To return to the upper menu or set other menu items, use the up arrow ( ) button. The available picture settings are described below.Menu Description3D MODE Select the format of 3D video data. (Enabled only for HDMI VIDEO TIMING)SIDE BY SIDE Left and right pictures are arranged in Side by Side layout. TOP & BOTTOM Left and right pictures are arranged in Top and Bottom layout. LINE INTERLACED Left and right pictures are arranged in line by line.OFF Turns off 3D Mode.3D L/R CHANGE Changes which frame is shown to each eye.R-L Odd lines are Right picture and even lines are Left picture.L-R Odd lines are Left picture and even lines are Right picture.3D - > 2D Converts 3D images into 2D. (Enabled only for HDMI VIDEO TIMING)OFF Displays images in 3D.ON Displays images in 2D. y3D Mode.SIDE BY SIDE TOP & BOTTOM LINE INTERLACED yIf the 3D option selected is incorrect, images may not be displayed properly.NOTE3D3D MODE3D L/R CHANGE3D - > 2DOFF(1/4)R-L(1/2)OFFVOLUMEEXITEXIT50
15ENGENGLISHCUSTOMIZING SETTINGSSUPER ENERGY SAVING Settings1 Press any button on the front of the Monitor set to display the MONITOR SETUP OSD menu.2 Press the MENU button to display the options in the OSD menu.3 Select SUPER ENERGY SAVING by pressing the buttons on the front of the Monitor set and set the options.4 Select EXIT to leave the OSD menu.To return to the upper menu or set other menu items, use the up arrow ( ) button.The available picture settings are described below.Menu DescriptionON Enables SUPER ENERGY SAVING you can save energy with this energy-efficient function.OFF Disables SUPER ENERGY SAVING.RESET Resets the values of total energy consumption reduction and CO2 emission reduction estimates. yTOTAL POWER REDUCTION: How much power is saved while using the monitor. yTOTAL CO2 REDUCTION: Change the TOTAL POWER REDUCTION to CO2. ySAVING DATA(W/h)546 mm(22 inch) 634 mm(25 inch)SUPER SAVING 4 W/h 5 W/hLED SAVING 15 W/h 12 W/h ySaving Data depends on the Panel. So,those values should be different from each panel and panel vendor. yLG calculated these values by using “broadcast video signal”. yLED Saving refers to how much power can be saved using a WLED Panel instead of CCFL panel. ySUPER SAVING refers to how much power can be saved using the SUPER ENERGY SAVING function.NOTEEXITOKON OFF RESETTOTAL POWER REDUCTION: 20 WTOTAL CO2 REDUCTION: 16 gSUPERSAVING : 5 W/hLEDSAVING: 12 W/hSUPER ENERGY SAVING
16ENGENGLISHTROUBLESHOOTING TROUBLESHOOTINGCheck the following before calling for service.No image appearsIs the power cord of the display connected? yCheck and see if the power cord is connected properly to the power outlet.Is the power indicator light on? yPress the Power button.Is the power on and the power indicator blue or green? yAdjust the brightness and the contrast.Is the power indicator flickering? yIf the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. yTry to turn on the PC.Do you see an "OUT OF RANGE" message on the screen? yThis message appears when the signal from the PC (video card) is out of horizontal or vertical frequency range of the display. See the 'Specifications' section of this manual and configure your display again.Do you see a "CHECK SIGNAL CABLE" message on the screen? yThis message appears when the signal cable between your PC and your display is not connected. Check the signal cable and try again.Do you see a "OSD LOCKED" message on the screen?Do you see “OSD LOCKED” when you push MENU button? yYou can secure the current control settings, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message “OSD UNLOCKED” will appear.Display image is incorrectDisplay Position is incorrect. yPress the AUTO button to automatically adjust your display image to the ideal setting.On the screen background, verticalbars or stripes are visible. yPress the AUTO button to automatically adjust your display image to the ideal setting. Any horizontal noise appearing in any image or characters are not clearly portrayed. yPress the AUTO button to automatically adjust your display image to the ideal setting. yCheck Control Panel ► Display ► Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color).
17ENGENGLISHTROUBLESHOOTINGDisplay image is incorrectThe screen color is mono or abnormal. yCheck if the signal cable is properly connected and use a screwdriver to fasten if necessary. yMake sure the video card is properly inserted in the slot. ySet the color setting higher than 24 bits (true color) at Control Panel ► Settings.The screen blinks. yCheck if the screen is set to interlace mode and if yes, change it to the recommend resolution.Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?Have you installed the display driver? yBe sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www.lg.com. yMake sure to check if the video card supports Plug&Play function. yCheck Control Panel ► Display ► Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. yIf the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. yThe setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer.CAUTION
18ENGENGLISHTROUBLESHOOTING WHEN USING 3D MODETROUBLESHOOTING WHEN USING 3D MODEI can see a swirling oil-like pattern on the monitor when the monitor is turned off. yThis is caused by the interference of external light in the air layer between the LCD surface and 3D filter. The pattern becomes almost invisible when you turn on the power again.I cannot see 3D image properlyIf you are not using the glasses provided with the monitor, yWhen you view 3D images with this monitor, it is very important that you use the glasses provided with the monitor. The glasses are designed to compensate optically for the 3D filter attached to the surface of the monitor. If you wear third-party glasses, you may not see 3D images properly on the monitor.If you view 3D images outside the optimal viewing angle or distance, yThe optimal viewing angle of the monitor is 12° in vertical direction while 80° in horizontal direction; the optimal viewing distance is between 50 cm to 90 cm from the monitor. When you view 3D images outside the optimal viewing angle or viewing distance, the images may look overlapped or not be displayed properly in 3D.If you have not set the resolution, yPlease set the resolution of the monitor to the maximum (1920 x 1080 @ 60 Hz) in the display settings. The 3D software may not work properly if the resolution is not set to the maximum.If the images that your left and right eyes see are reversed, yThe stripe images in the odd-numbered lines are the ones that your right eye sees on the monitor. If you only see the stripe images, not 3D images, set the images for your right eye to be displayed in the odd-numbered lines by changing the player or viewer option of the 3D software.I cannot see 3D but only 2D images. yThis monitor works both in 2D and 3D mode. You can view a video in 3D if it is made in 3D. If you try to view 2D images in 3D, they might not be displayed properly or you may experience poor picture quality.If the ‘TriDef 3D’ couldn’t work properly yThe minimum system requirements on PC to run the ‘TriDef 3D’ : »Intel® Core 2 Duo or AMD Athlon™ 64 X2 Dual-Core CPU or better »1GB RAM »NVIDIA® GeForce® 8600 GT or ATI X1650 XT »500MB free disk space »Windows® XP (SP2) (32 bit only), Windows® Vista (32 bit only) or Windows® 7 (32 or 64 bit) »DirectX 9.0c compatible sound card »Internet connection »DVD-ROM drive »Network card »DirectX 9.0c
19ENGENGLISHSPECIFICATIONSSPECIFICATIONS D2242PDisplay Screen Type 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 54.6 cmPixel Pitch 0.248 mm x 0.248 mm (Pixel Pitch)Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)Vertical Frequency 56Hz to 75Hz (D-SUB, DVI-D)56Hz to 61Hz (HDMI)Input Form Separate Sync. DigitalVideo Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)HDMI ConnectorInput Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalResolution Max D-SUB(Analog) : 1920 x 1080 @ 60 HzDVI / HDMI (Digital) : 1920 x 1080 @ 60 HzRecommend VESA 1920 x 1080 @ 60 HzPlug & Play DDC 2B(Analog,Digital,HDMI)Power Consumption On Mode : 34 W(Typ.)Sleep Mode ≤ 0.5 W Off Mode ≤ 0.5 W Power Input AC 100-240 V~ 50 / 60 Hz 1.0 ADimensions(Width x Height x Depth)With Stand 50.9 cm x 38.8 cm x 16.6 cmWithout Stand 50.9 cm x 32.2 cm x 5.8 cmWeight 3.0 kgTilt Range -5° to 15°EnvironmentalconditionsOperating TemperatureOperating Humidity10°C to 35 °C20 % to 80 % Storage TemperatureStorage Humidity-10°C to 60 °C 5 % to 90 % non-CondensingStand Base Attached ( ), Detached (O)Power cord Wall-outlet typeProduct specifications shown above may be changed without prior notice due to upgrade of product functions.
20ENGENGLISHSPECIFICATIONSSPECIFICATIONS D2542PDisplay Screen Type 63.4 cm (25 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 63.4 cmPixel Pitch 0.288 mm x 0.288 mm (Pixel Pitch)Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)Vertical Frequency 56Hz to 75Hz (D-SUB, DVI-D)56Hz to 61Hz (HDMI)Input Form Separate Sync. DigitalVideo Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)HDMI ConnectorInput Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalResolution Max D-SUB(Analog) : 1920 x 1080 @ 60 HzDVI / HDMI (Digital) : 1920 x 1080 @ 60 HzRecommend VESA 1920 x 1080 @ 60 HzPlug & Play DDC 2B(Analog,Digital,HDMI)Power Consumption On Mode : 39 W(Typ.)Sleep Mode ≤ 0.5 W Off Mode ≤ 0.5 W Power Input AC 100-240 V~ 50 / 60 Hz 1.2 ADimensions(Width x Height x Depth)With Stand 59.4 cm x 43.3 cm x 17.9 cmWithout Stand 59.4 cm x 37.1 cm x 6.1 cmWeight 4.4 kgTilt Range -5° to 15°EnvironmentalconditionsOperating TemperatureOperating Humidity10°C to 35 °C20 % to 80 % Storage TemperatureStorage Humidity-10°C to 60 °C 5 % to 90 % non-CondensingStand Base Attached ( ), Detached (O)Power cord Wall-outlet typeProduct specifications shown above may be changed without prior notice due to upgrade of product functions.
21ENGENGLISHSPECIFICATIONSPreset Modes (Resolution)Display Modes (Resolution) Horizontal Frequency(kHz)Vertical Frequency(Hz) Polarity(H/V)720 x 400 31.468 70 -/+640 x 480 31.469 60 -/-640 x 480 37.500 75 -/-800 x 600 37.879 60 +/+800 x 600 46.875 75 +/+1024 x 768 48.363 60 -/-1024 x 768 60.123 75 +/+1152 x 864 67.500 75 +/+1280 x 1024 63.981 60 +/+1680 x 1050 65.290 60 -/+1920 x 1080 67.500 60 +/+ Recommend ModeHDMI 3D TIMING3D Format Resolution Refresh Rate LimitationFrame Packing 1080 p 24 HzFrame Packing 720 p 50/60 HzSide-by-Side(Half) 1080 p 50/60 HzSide-by-Side(Half) 1080 i 50/60 HzSide-by-Side(Half) 720 p 50/60 HzTop-and-Bottom 1080 p 50/60 HzTop-and-Bottom 1080 p 24 HzTop-and-Bottom 720 p 50/60 HzIndicatorMode LED ColorOn Mode BlueSleep Mode Blinking BlueOff Mode Off
22ENGENGLISHPRECAUTIONS TO TAKE WHEN VIEWING 3D IMAGESPRECAUTIONS TO TAKE WHEN VIEWING 3D IMAGES1 If you view images in the 3D mode for a long period of time (playing games, watching movies etc.), you may feel dizzy. We strongly recommend you to take a rest after one hour of viewing 3D. (The time of experiencing dizziness varies depending on the individual.)2 Please view 3D images at the optimal viewing angle and at the recommended distance from the product. Otherwise, 3D images may appear to be overlapped or may not be displayed properly.3 If you view 3D images too closely for a long period of time, this may result in dizziness or blurred vision. Please use the device at the recommended distance.4 If you are pregnant, elderly or have heart problems, we recommend that you do not view 3D images. This is because the 3D images can cause disorientation and confusion.5 3D images can also cause nausea or vomiting for users under the influence of alcohol. In this situation, please do not view 3D images.6 Parents/guardians should monitor children’s viewing of 3D images because they may not be used to the 3D viewing experience and lack knowledge on how to handle potential risks.7 Do not use the 3D glasses as regular glasses, sunglasses or goggles. This may cause your vision to worsen.8 Do not keep the 3D glasses in an extremely hot or cold place. This may the shape of the glasses to change and become damaged. Do not use the 3D glasses if they are damaged because this may cause your vision to worsen, or you may experience dizzin.9 The lenses of the 3D glasses (polarizing film) are easily scratched. Use a soft clean cloth when cleaning them. Do not use any chemical cleaning products on the glasse. CAUTIONWarning about photosensitivity seizures ySome users may have a seizure or other abnormal symptoms when they are exposed to a flashing light or particular pattern in a video game or movie. If anyone in your family has a history of epilepsy or has ever experienced any kind of seizure, please consult with your doctor before viewing 3D images. If you exhibit any of the symptoms listed below when viewing 3D images, please stop viewing immediately and consult with your doctor even if you do not have previous medical problems of this nature.Symptoms yDizziness, blurred vision or facial tics, involuntary movements, twitching, blackouts, confusion, disorientation and wrong state.To prevent a photosensitivity seizure, please follow the instructions below. yDo not view 3D images when you are tired or ill. yDo not view 3D images for a long period of time. yReduce the depth of the 3D image.
23ENGENGLISHPROPER POSTUREProper posture for using the Monitor set.PROPER POSTUREMode Size(Inch) Optimal viewing distance (L) Optimal viewing angle (D)When viewing 3D images 54.6 cm/63.4 cm 50 cm to 90 cm 12°Precautions to take when viewing 3D images yWear the 3D glasses provided with the Monitor set. yWatch your posture. yRemain at the optimal distance and angle when viewing 3D images.(Viewing 3D images too closely may cause your vision to worsen, or you may experience dizziness.)50 cm to 90 cmAdjust the Monitor set and your posture to allow you to view images at the optimal viewing angle (D).Place your hands gently on the keyboard, keeping your arms bent at the elbows and horizontally outright.Adjust your distance from the Monitor set to allow you to view images from the optimal distance (L).Adjust the location of the Monitor set to avoid it reflecting light.
Make sure to read the Safety Precautions before using the product.Keep the Owner’s Manual (CD) in an accessible place for future reference.The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service. As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a set of power-savingguidelines issued by the U.S.EnvironmentalProtection Agency(EPA).MODELSERIAL

Navigation menu