LG Electronics USA DU42PX12XD 42-inch Plasma Monitor User Manual User s Manual H

LG Electronics USA 42-inch Plasma Monitor User s Manual H

UserManual.wiki >

LG Electronics USA >

DU42PX12XD User Manual

Users Manual

PLASMA TVOWNER’S MANUALPlease read this manual carefully and completely beforeoperating your TV. Retain this manual for future reference.Record model number and serial number of the TV in thespaces provided below. See the label attached on the back cover and relate thisinformation to your dealer if you require service.Model Number : Serial Number : MODEL: DU-42PX12XDLG Electronics U.S.A., Inc.

2 Plasma TVWarningWARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user tothe presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficientmagnitude to constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.WARNING:TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION:CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.NOTE TO CABLE/TV INSTALLER:This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall beconnected to the grounding system of the building, as close to the point of the cable entry as practical.REGULATORY INFORMATION:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip-ment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com-munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment. CAUTION:Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod-ification could void the user’s authority to operate this product.COMPLIANCE:The responsible party for this product’s compliance is:LG Electronics U.S.A., Inc1000 Sylvan Avenue, Englewood Cliffs, NJ 076321-800-243-0000http://www.lgusa.comWARNINGRISK OF ELECTRIC SHOCK DO NOT OPEN/CAUTIONWWarningarning

Owner’s Manual 3Safety InstructionsImportant safeguards for you and your new productYour product has been manufactured and tested with your safety in mind. However, improper use can result in electricalshock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observethe following safety points when installing and using your new product, and save them for future reference.Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operationthat are built into your new product.This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.1. Read InstructionsAll the safety and operating instructions should be readbefore the product is operated.2. Follow InstructionsAll operating and use instructions should be followed.3. Retain InstructionsThe safety and operating instructions should be retained forfuture reference.4. Heed WarningsAll warnings on the product and in the operating instructionsshould be adhered to.5. CleaningUnplug this product from the wall outlet before cleaning. Donot use liquid cleaners or aerosol cleaners. Use a dampcloth for cleaning.6. Water and MoistureDo not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet base-ment, or near a swimming pool.7. Accessories, Carts, and StandsDo not place this product on a slippery or tilted surface, or onan unstable cart, stand, tripod, bracket, or table. The productmay slide or fall, causing serious injury to a child or adult,and serious damage to the product. Use only with a cart,stand, tripod, bracket, or table recommended by the manu-facturer, or sold with the product. Any mounting of the prod-uct should follow the manufacturer’s instructions, and shoulduse a mounting accessory recommended by the manufac-turer.8. Transporting ProductA product and cart combination should be moved with care.Quick stops, excessive force, and uneven surfaces maycause the product and cart combination to overturn.9. AttachmentsDo not use attachments not recommended by the productmanufacturer as they may cause hazards.10. VentilationSlots and openings in the cabinet are provided for ventilationand to ensure reliable operation of the product and to protectit from overheating, and these openings must not be blockedor covered. The openings should never be blocked by plac-ing the product on a bed, sofa, rug, or other similar surface.This product should not be placed in a built-in installationsuch as a bookcase or rack unless proper ventilation is pro-vided or the manufacturer’s instructions have been adheredto.11. Power SourcesThis product should be operated only from the type of powersource indicated on the marking label. If you are not sure ofthe type of power supply to your home, consult your productdealer or local power company. For products intended tooperate from battery power, or other sources, refer to theoperating instructions.12. Power-Cord PolarizationThis product is equipped with a three-wire grounding typeplug, a plug having a third (grounding) pin. This plug will onlyfit into the grounding-type power outlet. This is a safety fea-ture. If you are unable to insert the plug into the outlet, con-tact your electrician to replace your obsolete outlet. Do notdefeat the safety purpose of the grounding-type plug.13. Power-Cord ProtectionPower-supply cords should be routed so that they are notlikely to be walked on or pinched by items placed upon oragainst them, paying particular attention to cords at plugs,convenience receptacles, and the point where they exit fromthe product.PORTABLE CART WARNINGSafety InstructionsSafety Instructions

4 Plasma TVSafety InstructionsAntenna Lead in WireAntenna Discharge Unit(NEC Section 810-20)Grounding Conductor(NEC Section 810-21)Ground ClampsPower Service GroundingElectrode System (NECArt 250, Part H)Ground ClampElectric ServiceEquipmentExample of Grounding According to NationalElectrical Code InstructionsNEC - National Electrical Code14. Outdoor Antenna GroundingIf an outside antenna or cable system is connected to theproduct, be sure the antenna or cable system is grounded soas to provide some protection against voltage surges andbuilt-up static charges. Article 810 of the National ElectricalCode (U.S.A.), ANSI/ NFPA 70 provides information withregard to proper grounding of the mast and supporting struc-ture, grounding of the lead-in wire to an antenna dischargeunit, size of grounding conductors, location of antenna-dis-charge unit, connection to grounding electrodes, andrequirements for the grounding electrode. 15. Lightning For added protection for this product (receiver) during a light-ning storm, or when it is left unattended and unused for longperiods of time, unplug it from the wall outlet and disconnectthe antenna or cable system. This will prevent damage to theproduct due to lightning and power-line surges.16. Power LinesAn outside antenna system should not be located in thevicinity of overhead power lines or other electric light orpower circuits, or where it can fall into such power lines orcircuits. When installing an outside antenna system, extremecare should be taken to keep from touching such power linesor circuits as contact with them might be fatal.17. OverloadingDo not overload wall outlets and extension cords as this canresult in a risk of fire or electric shock.18. Object and Liquid EntryNever push objects of any kind into this product throughopenings as they may touch dangerous voltage points orshort-out parts that could result in a fire or electric shock.Never spill liquid of any kind on the product.19. ServicingDo not attempt to service this product yourself as opening orremoving covers may expose you to dangerous voltage orother hazards. Refer all servicing to qualified service per-sonnel.20. Damage Requiring ServiceUnplug this product from the wall outlet and refer servicing toqualified service personnel under the following conditions:a. If the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into theproduct.c. If the product has been exposed to rain or water.d. If the product does not operate normally by following theoperating instructions. Adjust only those controls that arecovered by the operating instructions as an improperadjustment of other controls may result in damage andwill often require extensive work by a qualified technicianto restore the product to its normal operation.e. If the product has been dropped or the cabinet has beendamaged.f. If the product exhibits a distinct change in performance.21. Replacement PartsWhen replacement parts are required, be sure the servicetechnician has used replacement parts specified by the man-ufacturer or have the same characteristics as the originalpart. Unauthorized substitutions may result in fire, electricshock, or other hazards.22. Safety CheckUpon completion of any service or repairs to this product,ask the service technician to perform safety checks to deter-mine that the product is in proper operating condition.23. Wall or Ceiling MountingThe product should be mounted to a wall or ceiling only asrecommended by the manufacturer. The product may slideor fall, causing serious injury to a child or adult, and seriousdamage to the product.24. HeatThe product should be situated away from heat sourcessuch as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat.Safety Instructions continuedSafety Instructions continued

Owner’s Manual 5ContentsAfter reading this manual, keep it handy for future reference.Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4IntroductionControls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Connection Options . . . . . . . . . . . . . . . . . . . . . .8Remote Control Key Functions . . . . . . . . . . . . . .9InstallationInstallation Instruction . . . . . . . . . . . . . . . . . . .10~11External Equipment Connections . . . . . . . . . .12~16Antenna Connection . . . . . . . . . . . . . . . . . . . . .12VCR Setup / Cable TV Setup . . . . . . . . . . . . . .13External A/V Source Setup . . . . . . . . . . . . . . . .14Monitor Out Setup / DVD Setup . . . . . . . . . . . .14HDSTB Setup / Digital Audio Output . . . . . . . . .15PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16OperationScreen Setup for PC mode . . . . . . . . . . . . . . . . . .17Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .18On-screen Menus Language Selection . . . . . . . . .18Setup Menu OptionsEZ Scan (Channel Search) . . . . . . . . . . . . . . . .19Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .19DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .20Channel Label Setup . . . . . . . . . . . . . . . . . . . .20Main Picture Source Selection . . . . . . . . . . . . .20Video Menu OptionsEZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Manual Picture Control (Off Option) . . . . . . . . .21Color Temperature Control . . . . . . . . . . . . . . . .21Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .21Audio Menu OptionsAudio Language . . . . . . . . . . . . . . . . . . . . . . . .22EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .22Manual Sound Control (Off Option) . . . . . . . . . .23Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .23Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .23TV Speakers On/Off Setup . . . . . . . . . . . . . . . .24BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Time Menu OptionsAuto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .25Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .25On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .25Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .26Option Menu FeaturesAspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .27Caption / Caption Mode . . . . . . . . . . . . . . . . . .28Caption Option . . . . . . . . . . . . . . . . . . . . . . . .29Cinema Mode Setup . . . . . . . . . . . . . . . . . . . .29Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .30Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Lock Menu OptionsParental Lock Setup . . . . . . . . . . . . . . . . . . . . .32PIP (Picture-in-Picture)/POP/Twin PictureWatching PIP/POP/Twin Picture . . . . . . . . . . . ..33Selecting an Input Signal Source for PIP/Twin Picture . .33Swapping the PIP/Twin Picture . . . . . . . . . . . . .33TV Program Selection for PIP . . . . . . . . . . . . . .33Moving the PIP sub picture . . . . . . . . . . . . . . . .34Adjusting Main and Sub Picture Sizes for Twin Picture . .34POP (Picture-out-of-Picture: Channel Scan) . . .34External Control Device Setup . . . . . . . . . . . . . . . .35~39IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40~41Programming the Remote . . . . . . . . . . . . . . . . . . . . . .42Programming Codes . . . . . . . . . . . . . . . . . . . . . . .43~44Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .45Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47~48ContentsContentsSetup and Operation ChecklistSetup and Operation ChecklistSetup and Operation Checklist(See pages 11~16 for available connection and operational setup options.)1. Unpack TV and all accessories.2. Connect all external video and audio equipment.see pages 14 ~ 16.3 Install batteries in remote control.See page 9.4. Turn TV on.See page 18.5. Turn video source equipment on.6. Select viewing source for TV.See page 20.7. Fine-tune source image and sound to your personal prefer-ence or as required by source. See pages 21 ~ 24.8. Additional features set upSee Contents above.

6 Plasma TVIntroductionIntroductionIntroductionWhat is a Plasma Display Panel (PDP)?A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image qualityand large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be alsobe viewed as a series of fluorescent lamps. How does it work?PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue.Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phos-phors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5inches thick. 160° - Wide angle range of visionYour flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display isclear and visible to viewers anywhere in the room who can see the screen. Wide ScreenThe screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.MultimediaConnect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picturefeature allows you to view your PC and video images simultaneously.VersatileThe light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will notfit.The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screenThe PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few celldefects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should beacceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defec-tive. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology mini-mizes these cell defects during the manufacture and operation of this product.

Owner’s Manual 7IntroductionControlsControlsON/OFFTV/VIDEOMENUVOL CH- This is a simplified representation of front panel. Image shown may be somewhat different from your TV.Front Panel ControlsFront Panel ControlsON/OFF ButtonRemote Control Sensor VOLUME (FF,G) ButtonsPower Standby IndicatorIlluminates red in standby mode,Illuminates green when the TV isturned on.CHANNEL (E,D) ButtonsMENU ButtonTV/VIDEO Button

8 Plasma TVIntroductionConnection OptionsConnection OptionsRS-VIDEOVIDEO L / MONO AUDIOA/V 2 REMOTECONTROLRS-232C INPUT(CONTROL/SERVICE)AC INPUTAUDIO INPUTCOMPONENT 2COMPONENT 1RLDIGITAL AUDIO(OPTICAL)DVIINPUTCOMPONENT1INPUTOUTPUTAUDIO INPUTDVI INPUT(PC/DTV INPUT)RGB INPUT(PC/DTV INPUT)VIDEO INPUTDVDDTVINPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEOS-VIDEOAntennaAnalog/DTV.Back Connection PanelBack Connection PanelAntenna 1-2 InputsConnect cable or antenna signals to theTV, either directly or through your cablebox. For DTV use Antenna 2 only.DVI Input/Audio Input/RGBInputConnect the monitor output con-nector from a PC to the appro-priate input port.Digital Audio (DVI: Digital VisualInterface/Component1) Input/Digital Audio OutputConnect digital audio from various typesof equipment. Note: In standby mode, these ports will not work.Audio/Video Input 1Connect audio/video out-put from an externaldevice to these jacks.DVD/DTV Input (Component1-2)Connect a componentvideo/audio device to thesejacks. Monitor OutputConnect a second TV orMonitor.Remote ControlPortConnect your wiredremote control here.S-Video InputConnect S-Video out from anS-VIDEO device to the S-VIDEO input.Power Cord SocketThis TV operates on an AC power. The voltage is indi-cated on the Specifications page. Never attempt to oper-ate the TV on DC power.S-VIDEO InputA connection available to provide betterpicture quality than the video input.VIDEO InputConnects the video signal from a videodevice.AUDIO InputUse to connect to hear stereo soundfrom an external device.RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C porton a PC.

Owner’s Manual 9Installation- When using the remote control, aim it at the remote control sensor on the TV.LIGHTTV/VIDEOMODECOMP/RGB/DVIMUTE SURFVOL CHINFOSAP RATIOCCMENUSOUND VIDEOEXITPLAY PAUSE STOP RECORDPIP PIPCH- PIPCH+ PIPINPUTFREEZEADJUST OKZOOM SIGNAL SWAPREW FF SKIPPOWERTIMERFLASHBKLIGHTIlluminates the remote control buttons.TV/VIDEOSelects: DTV, Analog, Video1-2,Component 1-2, RGB-DTV (or RGB-PC),DVI-DTV (or DVI-PC) input sources.COMP/RGB/DVISelects: Component 1-2, RGB-DTV (or RGB-PC), DVI-DTV (or DVI-PC) input sources.NUMBER buttonsDASHUsed to enter a program number for multipleprogram channels such as 2-1,2-2,etc.MUTESwitches the sound on or off.VCR/DVD BUTTONSControl some video cassette recorders orDVD player ("RECORD" button is not avail-able for DVD player).RATIOChanges the aspect ratio.MODESelects the remote operating mode: TV,VCR, DVD, CABLE, HDSTB or AUDIO.Select other operating modes, for theremote to operate external devices.POWERTurns your TV or any other programmedequipment on or off, depending on mode.TIMERLets you select the amount of time beforeyour TV turns itself off automatically.SURFUse to scroll the Surf channel list.CCSelect a closed caption:Off, EZ Mute, and On.FLASHBKTunes to the last channel viewed.THUMBSTICK (Up/Down/Left/Right/OK)Allows you to navigate the on-screenmenus and adjust the system settings toyour preference.CHANNEL UP/DOWNSelects available channels foundwith EZ scan.EXITClears all on-screen displays and returns toTV viewing from any menu.VIDEOAdjusts the factory preset picture accordingto the room.VOLUME UP/DOWNIncreases/decreases the sound level.SAPSelects MTS sound: Mono, Stereo, and SAP.Change the audio language in DTV mode.MENUBrings up the main menu to the screen.INFOWhen you watch the TV, displays informationon top of the screen. Not available inComponent 1-2, RGB and DVI mode.SOUNDSelects the sound appropriatefor the program's character. PIPSwitches between PIP, POP (Picture-out-of-Picture) and Twin picture modes.PIPCH-/PIPCH+Changes to next higher/lower PIP channel.PIP INPUTSelects the input source for the sub picture.SWAPExchanges the PIP/main images.FREEZEFreezes the currently-viewed picture. Mainpicture is frozen in PIP/Twin picturre mode.ADJUSTAdjusts screen position, clock, andphase in PC mode.ZOOMEnlarges the main picture size.SIGNALDisplays the digital signal strength.Installing Batteries• Open the battery compartment cover on the back side and install the batteriesmatching correct polarity (+ with +, - with -).• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.Replace cover.Remote Control Key FunctionsRemote Control Key Functions

10 Plasma TVInstallationInstallationInstallationOwner’s Manual1.5V1.5VBatteries Power CordLIGHTTV/VIDEOMODECOMP/RGB/DVIMUTE SURFVOL CHINFOSAP RATIOCCMENUSOUND VIDEOEXITPLAY PAUSE STOP RECORDPIP PIPCH- PIPCH+ PIPINPUTFREEZEADJUST OKZOOM SIGNAL SWAPREW FF SKIPPOWERTIMERFLASHBKRemote Control75ΩRound CableEnsure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealerwhere you purchased the product.- Secure the TV assembly by attaching it to a wall for additional support.Attaching the Attaching the TV assembly to the wallTV assembly to the wall• Install the TV brackets on the TV as shown.Insert the 2 bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the product), as shown.Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely.• Secure the TV assembly to the wall with strong strings orwound wire cables, (not supplied with the product), asshown.2-TV brackets2-Wall brackets2-TV bracket bolts

Owner’s Manual 11InstallationInstallation InstructionsInstallation Instructions• The TV can be installed in various ways such as on a wall, or on a desktop etc.• The TV is designed to be mounted horizontally. The speakers shown are optional.GROUNDINGEnsure that you connect the grounding / earth wire to prevent possibleelectric shock. If grounding methods are not possible, have a qualifiedelectrician install a separate circuit breaker. Do not try to ground theunit by connecting it to telephone wires, lightening rods, or gas pipes.PowerSupplyShort-circuitBreaker4 inches4 inches4 inches4 inches2 inchesWWall Mount: Horizontal installationall Mount: Horizontal installationFor proper ventilation, allow a clearance of 4” on eachside and 2” from the wall. Detailed installation instruc-tions are available from your dealer, see the optionalWall Mounting Bracket Installation and Setup Guide.4 inches4 inches2.36 inches4 inches2 inchesDesktop Pedestal InstallationDesktop Pedestal InstallationFor proper ventilation, allow a clearance of 4” on eachside and the top, 2.36” on the bottom, and 2” from thewall. Detailed installation instructions are included inthe optional Desktop Stand Installation and SetupGuide available from your dealer.To Mount on a WallWall mount minimum allowable clearances for ade-quate ventilation.To Install on a DesktopPedestal mount minimum allowable clearances foradequate ventilation.

12 Plasma TVInstallation- Antenna or Cable Service without a Cable Box Connections- For optimum picture quality, adjust antenna direction if needed.Antenna ConnectionAntenna ConnectionAnalog and Digital TV signals provided on one antennaNOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches.The TV will let you know when the analog, cable, and digital channel scans are complete.Analog and DTV signals provided on two separate antennas• In a poor signal area to improve picture quality, purchaseand install a signal amplifier.• If the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter” in the connections.• If the antenna is not installed properly, contact your deal-er for assistance.AC INPUTRT1AUDIOR L(MONO)VIDEOS-VIDEOAntennaAnalog/DTVMulti-family Dwellings/Apartments(Connect to wall antenna socket)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)OutdoorAntennaWall AntennaSocketVHF AntennaUHF AntennaRF Coaxial Wire (75 ohm)Copper WireTurn clockwise to tighten.Copper WireBe careful not to bend the Copper wire whenconnecting the antenna.AC INPUTTORPUTVT 1AUDIOR L(MONO)VIDEOS-VIDEOAntennaAnalog/DTVWall AntennaSocket RF Coaxial Wire (75 ohm)Analog AntennaDigital AntennaCopper WireCopper WireTurn clockwise to tighten.Wall AntennaSocket RF Coaxial Wire (75 ohm)External Equipment ConnectionsExternal Equipment ConnectionsAC INPUTAntennaAnalog/DTVSignalAmplifier

Owner’s Manual 13InstallationNOTE: All cables shown are not included with the TV- To avoid picture noise (interference), leave an adequate distance between the VCR and TV- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time.Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen mayremain visible on the screen.Connection Option 1Set VCR output switch to 3 or 4 and then tuneTV to the same channel number.Connection Option 21. Connect the audio and video cables from theVCR's output jacks to the TV input jacks, asshown in the figure. When connecting the TV to VCR, match thejack colors (Video = yellow, Audio Left = white,and Audio Right = red).If you connect an S-VIDEO output from VCR tothe S-VIDEO input, the picture quality isimproved; compared to connecting a regularVCR to the Video input.2. Insert a video tape into the VCR and pressPLAY on the VCR. (Refer to the VCR owner’smanual.)3. Select the input source with using theTV/VIDEO button on the remote control. (Ifconnected to A/V INPUT 1, select Video 1input source)Do not connect to both Video andS-Video at the same time.VCR SetupVCR SetupAC INPUTAUDIO INPUTCOMPONENT 2COMPONENT 1RLPUTAUDIO INPUTDVI INPUT(PC/DTV INPUT)RGB INPUT(PC/DTV INPUT)VIDEO INPUTDVDDTVINPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEOS-VIDEO Antenna Analog/DTVS-VIDEO OUTIN(R) AUDIO (L) VIDEO34OUTPUTSWITCHANT OUTANT IN.- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.- For further information regarding cable TV service, contact your local cable TV service provider(s).Connection Option 11. Select 3 or 4 with channel switch on cablebox.2. Tune the TV channel to the same selectedoutput channel on cable box.3. Select channels at the cable box or with thecable box remote control.Connection Option 21. Connect the audio and video cables from theCable Box's output jacks to the TV input jacks,as shown in the figure. When connecting the TV to a Cable Box,match the jack colors (Video = yellow, AudioLeft = white, and Audio Right = red).2. Select the input source with using theTV/VIDEO button on the remote control. (Ifconnected to A/V INPUT 1, select Video 1input source)3. Select your desired channel with the remotecontrol for cable box.CableCable TV SetupTV SetupAC INPUTAUDIO INPUTCOMPONENT 2COMPONENT 1RLIO INPUTRGB INPUT(PC/DTV INPUT)VIDEO INPUTDVDDTVINPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEOS-VIDEO Antenna Analog/DTVTVVCR RF Cable (R) AUDIO (L) VIDEO34OUTPUTSWITCH.VCRCable Box1212

14 Plasma TVInstallation•Component Input portsTo get better picture quality, connect a DVD player to the compo-nent input ports as shown below.How to connectConnect the audio and video cables from the external equip-ment's output jacks to the TV input jacks, as shown in thefigure.When connecting the TV to external equipment, match thejack colors (Video = yellow, Audio Left = white, and AudioRight = red).How to use1. Select the input source with using the TV/VIDEO button onthe remote control. (If connected to A/V INPUT 1, selectVideo 1 input source).2. Operate the corresponding external equipment. Refer toexternal equipment operating guide.Component ports on the TV YPBPRVideo output ports on DVD playerYYYYPbB-YCbPBPrR-YCrPRHow to connect1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y,PB, PR) INPUT jacks on the TV and connect the DVD audio outputsto the AUDIO INPUT jacks on the TV, as shown in the figure.2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to theAUDIO INPUT jacks on the TV, as shown in the figure.NOTE: If your DVD player does not have component video output, useS-Video.How to use1. Turn on the DVD player, insert a DVD.2. Use the TV/VIDEO or COMP/RGB/DVI button on the remote controlto select Component 1 or Component 2. (If connected to S-VIDEO, select the Video 1 or Video 2 external input source.)3. Refer to the DVD player's manual for operating instructions.ExternalExternal A/V Source SetupA/V Source SetupDVD SetupDVD SetupRLAUDIO VIDEOAC INPUTAUDIO INPUTCOMPONENT 2COMPONENT 1RLNPUTV INPUT)VIDEO INPUTDVDDTVINPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEO Antenna Analog/DTVS-VIDEO.REMOTECONTROLRS-232C INPUT(CONTROL/SERVICE)AUDIO INPUTCOMPONENT 2COMPONENT 1RLDIGITAL AUDIO(OPTICAL)DVIINPUTCOMPONENT1INPUTOUTPUTVIDEO INPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEOAntenna 1Analog/DTVAnte DBR(R) AUDIO (L)DIGITAL AUDIOOPTICAL (R) AUDIO (L)S-VIDEOS-VIDEODVDDTVINPUT.DVDorCamcorderVideo Game SetThe TV has a special signal output capability which allows you tohook up a second TV or monitor.Connect the second TV or monitor to the TV’s MONITOR OUTPUT.See the Operating Manual of the second TV or monitor for furtherdetails regarding that device’s input settings.NOTE• Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV, DTV inputsources cannot be used for Monitor out.NOTES• Digital Audio will not work for Component 2 input source.• Digital Audio operation has priority if Digital Audio and AUDIO L/Rare connected at the same time.AC INPUTAUDIO INPUTCOMPONENT 2COMPONENT 1RLRGB INPUT(PC/DTV INPUT)VIDEO INPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEOS-VIDEO Antenna Analog/DTVS-VIDEO IN(R) AUDIO (L)VIDEODVDDTVINPUT.Monitor Out SetupMonitor Out Setupor

Owner’s Manual 15InstallationSend the TV’s audio to external audio equipment (stereo system) viathe Digital Audio Output Optical port.How to connect1. Connect one end of an optical cable to the TV Digital Audio OpticalOutput port.2. Connect the other end of the optical cable to the digital audio opticalinput on the audio equipment.3. Set the “ TV Speaker option - Off” in the AUDIO menu. Refer topage 23.See the external audio equipment instruction manual for operation.Caution: Do not look into the optical output port.Looking at the laser beam may damageyour vision.DigitalDigital Audio OutputAudio Output- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digitalsignals from a digital set-top box or other digital external device, refer to the figure as shown below.- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) mode.How to connectUse the TV’s COMPONENT (Y, PB, PR) INPUT, RGB or DVI jack forvideo connections, depending on your set-top box connector. Then,make the corresponding audio connections.How to use1. Turn on the digital set-top box. (Refer to the owner’s manual for thedigital set-top box.) 2. Use TV/VIDEO or COMP/RGB/DVI on the remote control to selectComponent 1,Component 2,RGB-DTV, or DVI-DTV source.HDSTB SetupHDSTB SetupREMOTECONTROLRS-232C INPUT(CONTROL/SERVICE)AC INPUTAUDIO INPUTCOMPONENT 2COMPONENT 1RLDIGITAL AUDIO(OPTICAL)DVIINPUTCOMPONENT1INPUTOUTPUTAUDIO INPUTDVI INPUT(PC/DTV INPUT)RGB INPUT(PC/DTV INPUT)VIDEO INPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEO Antenna Analog/DTVR(R) AUDIO (L)RGB-DTV OUTPUTBR(R) AUDIO (L)DIGITAL AUDIOOPTICAL(R) AUDIO (L)DVI-DTV OUTPUTDIGITAL AUDIOOPTICALS-VIDEODVDDTVINPUT.Digital Set-top Boxor oror orREMOTECONTROLRS-232C INPUT(CONTROL/SERVICE)AUDIO INPUTCOMPONENCOMPONENRLDIGITAL AUDIO(OPTICAL)DVIINPUTCOMPONENT1INPUTOUTPUTAUDIO INPUTDVI INPUT(PC/DTV INPUT)RGB INPUT(PC/DTV INPUT)Signal480i480p720p1080iComponent 1/2YesYesYesYesRGB-DTV,DVI-DTVNoYesYesYes

16 Plasma TVInstallationHow to connect1. To get the best picture quality, adjust the PCgraphics card to 1024x768, 60Hz.2. Use the TV’s RGB INPUT or DVI (Digital VisualInterface) INPUT port for video connections,depending on your PC connector. • If the graphic card on the PC does not outputanalog and digital RGB simultaneously, connectonly one of either RGB INPUT or DVI INPUT todisplay the PC on the TV.• If the graphic card on the PC does output analogand digital RGB simultaneously, set the TV toeither RGB or DVI; (the other mode is set to Plugand Play automatically by the TV.)3. Then, make the corresponding audio connections.If using a sound card, adjust the PC sound asrequired.How to use1. Turn on the PC and the TV.2. Turn on the display by pressing the POWER button on the TV's remote control.3. Select RGB-PC or DVI-PC input source in main input option of SETUP menu. (Refer to P.20)4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or bright-ness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to anotherrate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphiccard can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable. • Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become per-manently imprinted on the screen. Use the Orbiter screen saver when possible.• The synchronization input form for Horizontal and Vertical frequencies is separate.PC SetupPC SetupEMOTENTROL AUDIO INPUTCOMPONENT 2COMPONENT 1RLDIGITAL AUDIO(OPTICAL)DVIINPUTCOMPONENT1INPUTOUTPUTAUDIO INPUTDVI INPUT(PC/DTV INPUT)RGB INPUT(PC/DTV INPUT)VIDEO INPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEOAntenna 1Analog/DTVS-VIDEODVDDTVINPUT.- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends config-uration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC)protocol.- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. card, change the screen scanning rate for thegraphic card accordingly.Resolution640x350720x400640x480800x600HorizontalFrequency(KHz)31.46837.86131.46937.92731.46937.86137.50043.26970.0985.0870.0885.0359.9472.8075.0085.0035.15637.87948.07746.87553.67448.36356.47660.02356.2560.3172.1875.0085.0660.0070.0675.02VerticalFrequency(Hz) Resolution HorizontalFrequency(KHz)VerticalFrequency(Hz)1024x768Monitor Display Specifications (RGB-PC / DVI-PC Mode)

Owner’s Manual 17InstallationOperationOperation- Be sure to select the RGB-PC/RGB-DTV source before operation. (For RGB-DTV input source, Position and Reset are available.)- In DVI-PC and DVI-DTV input source, settings are not adjustable. - You can manually adjust picture position and minimize image shaking for the PC input source.1. Press the ADJUST button and then use D/Ebutton to select POSITION,CLOCK, or PHASE.2. Press OK button and then use D/E/F/Gbuttons to make appropriate adjust-ments.• The PHASE adjustment range is -16 ~ +16.• The CLOCK adjustment range is -30 ~ +30.3. Press OK button.Adjustment for screen Position, Clock, and PhaseAdjustment for screen Position, Clock, and PhaseScreen Setup for PC modeScreen Setup for PC mode1. Press the ADJUST button and then use D/Ebutton to select the RESET option.2. Press OK button and then use F/Gbutton to select Yes.3. Press OK buttonInitializing (Reset to original factory values)Initializing (Reset to original factory values)- To initialize the adjusted valuesClosePOSITION GCLOCKPHASERESETAdjustDFGEClosePOSITIONCLOCKPHASERESET GAdjustInitialize Settings

18 Plasma TVOperationOn-screen Menus Language SelectionOn-screen Menus Language SelectionTTurning the TV Onurning the TV OnTurning on the TV just after installationTurning on the TV (power cord is still connected)1. Connect power cord correctly.2. Press the ON/OFF button on the TV. At this moment, the TV is switched to standby mode.Press the TV/VIDEO,CH (D/E)button on the TV or press the POWER,TV/VIDEO,COMP/RGB/DVI,CH (+,-),Number (0 ~ 9) button on the remote control and then the TV willswitch on.• Press the ON/OFF button on the TV to turn the TV on.1. If the TV was turned off with the ON/OFF button on the TV2. If the TV was turned off with the remote control and then the ON/OFF button on the TV• Press the ON/OFF button on the TV and then press the POWER,TV/VIDEO,COMP/RGB/DVI,CH (+,-),Number (0 ~ 9) button on the remote control to turn the TV on.-The menus can be shown on the screen in the selected language. First select your language.1. Press the MENU button and then use D/Ebutton to select the OPTION menu.2. Press the Gbutton and then use D/Ebutton to select Language.3. Press the Gbutton and then use D/Ebutton to select your desired language.From this point on, the on-screen menus will be shown in the selected language.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.NOTE• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Aspect RatioCaptionCaption ModeCaption OptionLanguage GCinemaDemoISM MethodLow PowerEnglishEspañolFrançaisMENU

Owner’s Manual 19OperationSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Select antenna input,pressMENU- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.- Run EZ Scan again after any Antenna/Cable connection changes.1. Press the MENU button and then use D/Ebutton to select the SETUP menu.2. Press the Gbutton and then use D/Ebutton to select EZ Scan.3. Press the Gbutton and then use D/Ebutton to select antenna input (Based on your connections to antenna 1-2).• Analog/DTV Air: Watching the Over-the-air, cable, and digital over-the-air signals via antenna 1 input port• Analog/DTV Cable: Watching the Over-the-air, cable, and digital cable signals via antenna 1 input port• Analog+DTV Air (ANT2): Watching the Over-the-air, and cable signal via antenna 1 input port and the digital over-the-air signal via antenna 2 input port• Analog/DTV Cable (ANT2): Watching the Over-the-air, and cable signal via antenna 1 input port and the digital cable signal via antenna 2 input port* Cable Service Band Note: Select Std=Standard, HRC=HRC Band, or IRC=IRC Band.(For further band information, contact your cable service provider.)4. Press the OK button to begin the channel search.Allow EZ Scan to complete the channel search cycle for TV, CATV, and DTV/CADTV.EZ Scan (Channel Search)EZ Scan (Channel Search)SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.EZ ScanCh.Edit GDTV SignalCh. LabelMain InputSub InputSET IDSelection ( Gor ) leads youto the channel edit screen.MENU- Create two different types of channel lists in memory: “Custom list” and “Surf"(Favorite) channel list” from the default channel list created from the EZ Scanchannel search. - A custom list can be created by toggling each channel on or off with OK button.Once a channel is highlighted, you will be able to see whether the channel iscurrently added or deleted by referring to the small window at the top-left cornerof the screen. You can create your own Surfchannel list with up to 10 channels.It appears at the bottom-left corner of the screen. Use the SURF button on theremote control when a channel is highlighted, to add or delete the channel fromthe Surf channel list.- You can create your SURF channel list from the channel list memorized fromEZ Scan.- CATV is available for 1-125 channel.1. Press the MENU button and then use D/Ebutton to select the SETUP menu.2. Press the Gbutton and then use D/Ebutton to select Ch. Edit.3. Press the Gbutton. You will now see a screen filled with channel numbers anda preview picture. 4. Use D/E/F/Gbutton to select a channel and then use the OK button to addor delete it. Press SURF to add the channel to the Surf List.5. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.Channel EditChannel EditSetup Menu OptionsSetup Menu OptionsAnalog/DTV AirAnalog/DTV CablePrev.Select antenna input,pressMENUAnalog/DTV AirAnalog/DTV CableEZ ScanCh.EditDTV SignalCh. LabelMain InputSub InputSET IDSelect DTV cable band,press1. STD2. HRC3. IRCAirANT 1CableANT 1

Owner’s Manual 21Operation- Adjust the picture appearance to suit your preference and viewing situations.1. Press the MENU button and then use D/Ebutton to select the VIDEO menu.2. Press the Gbutton and then use D/Ebutton to select the desired picture option(Contrast,Brightness,Color,Sharpness, or Tint).3. Press the Gbutton and then use F/Gbutton to make appropriate adjustments.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.1. Press the VIDEO button repeatedly to select the picture appearance setup option as shown below:Off (your own settings), Day Light,Normal,Night Time,Movie,Video Game, and Sports.• You can also use the VIDEO menu to adjust EZ Picture.2. Press the EXIT button to save and return to TV viewing.EZ PictureEZ PictureManual Picture Control (Manual Picture Control (Off option)option)- Choose one of three automatic color adjustments. Set to warm to enhance hottercolors such as red, or set to cool to see less intense colors with more blue.1. Press the MENU button and then use D/Ebutton to select the VIDEO menu.2. Press the Gbutton and then use D/Ebutton to select Color Temperature .3. Press the Gbutton and then use D/Ebutton to select either Warm,Medium,or Cool.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.ColorColor TTemperature Controlemperature Control- Use to quickly reset all the Video menu options to their original factory presetvalues.1. Press the MENU button and then use D/Ebutton to select the VIDEO menu.2. Press the Gbutton and then use D/Ebutton to select Video Preset .3. Press the Gbutton to reset the Video menu options to original values.VVideo Presetideo Preset- EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on theprogram category.- When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZPicture automatically changes to Off.-Day Light,Normal,Night Time,Movie,Video Game, and Sports settings are preset for optimum picture qualityat the factory and are not adjustable.VVideo Menu Optionsideo Menu OptionsSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.EZ PictureContrastBrightnessColorSharpnessTintColor Temperature GVideo PresetWarmMediumCoolMENUSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.EZ PictureContrastBrightnessColorSharpnessTintColor TemperatureVideo Preset GMENUSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.EZ PictureContrast 85 GBrightness 50Color 50Sharpness 50Tint 0Color TemperatureVideo PresetMENUSelection ( Gor ) presetsthe video configuration.R G

22 Plasma TVOperation- Other languages may be available if a digital signal is provided by the broad-casting station. Audio Menu OptionsAudio Menu Options1. Press the SOUND button repeatedly to select the appropriate sound setup as shown below:Off (your own settings), Normal,Stadium,Theater, and Music.• You can also adjust EZ Sound in the AUDIO menu.2. Press EXIT button to save and return to TV viewing.EZ SoundEZ Sound1. Press the MENU button and then use D/Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D/Ebutton to select Audio Language.3. Press the Gbutton and then use D/Ebutton to select: English, Spanish, orFrench.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.Audio LanguageAudio Language- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate soundoptions based on the program content.- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Off.-Normal,Stadium,Theater, and Music are preset for good sound quality at the factory and are not adjustable.- Scans for changes in sound level during commercials, then adjusts the soundto match the specified audio level. SoundRite makes sure that the volume levelremains consistent whether you are watching a commercial or a regular TVprogram.1. Press the MENU button and then use D/Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D/Ebutton to select EZ SoundRite.3. Press the Gbutton and then use D/Ebutton to select On or Off.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.EZ SoundRiteEZ SoundRiteSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Audio Language GEZ SoundRiteEZ SoundBalanceTrebleBassFront SurroundTV SpeakerBBEEnglishSpanishFrenchMENUSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Audio LanguageEZ SoundRite GEZ SoundBalanceTrebleBassFront SurroundTV SpeakerBBEOffOnMENU

Owner’s Manual 23OperationSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Audio LanguageEZ SoundRiteEZ SoundBalanceTrebleBassFront Surround GTV SpeakerBBEOff3D EchoSound SystemSRS TruSurround XTMENU1. Press the MENU button and then use D/Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D/Ebutton to select Front Surround.3. Press the Gbutton and then use D/Ebutton to select Off,3D EchoSoundSystem or SRS (Sound Retrieval System) TruSurround XT..•SRS TruSurround XTTakes advantage of any multi-channel format without needing to add extraspeakers or equipment. Dialog clarity, bass enrichment, and the addition ofstereo audio enhancement that produces an immersive sound experience fromstandard stereo material. •3D EchoSound SystemCreates a stunning simulated stereo effects from any mono sound and a real-istic three-dimensional sound with a very wide and deep sound stage intostereo sound.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.Front SurroundFront Surround1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono,Stereo, or SAP appear in turn. • If other languages available on the digital signal, select them with the SAP button.2. Press EXIT button to save and return to TV viewing.Stereo/SAPStereo/SAP Broadcasts SetupBroadcasts Setup- This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; ifthe station transmits an additional sound signal as well as the original one.- Stereo or SAP can be received only when the TV station transmits those signals even though you have selected Stereo orSAP.- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.- Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting. - is a trademark of SRS Labs, Inc.- TruSurround XT technology is incorporated under license from SRS Labs, Inc.- Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. 1. Press the MENU button and then use D/Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D/Ebutton to select the desired sound option(Balance,Treble, or Bass).3. Press the Gbutton and then use F/Gbutton to make appropriate adjustments.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.Manual Sound Control (Manual Sound Control (Off option)option)SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Audio LanguageEZ SoundRiteEZ SoundBalance 0 GTreble 50Bass 50Front SurroundTV SpeakerBBEMENUL R- Adjust the sound to suit your taste and room situations. Audio Menu Options continuedAudio Menu Options continued

24 Plasma TVOperationSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Audio LanguageEZ SoundRiteEZ SoundBalanceTrebleBassFront SurroundTV Speaker GBBEOffOnMENU1. Press the MENU button and then use D/Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D/Ebutton to select TV Speaker.3. Press the Gbutton and then use D/Ebutton to select On or Off.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.TV Speakers On/OfTV Speakers On/Off Setupf Setup- Turn TV speakers off if using external audio equipment. Feature turns the TVSpeakers option On or Off.SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Audio LanguageEZ SoundRiteEZ SoundBalanceTrebleBassFront SurroundTV SpeakerBBE GMENU1.Press the MENU button and then use D/Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D/Ebutton to select BBE.3. Press the Gbutton and then use D/Ebutton to select On or Off.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.BBEBBE- BBE High Definition Sound restores clarity and presence for better speechintelligibility and music realism.OffOn

Owner’s Manual 25OperationTTime Menu Optionsime Menu OptionsSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Auto Clock GManual ClockOff TimerOn TimerSleep TimerAuto OffOffOnTime Zone EasternMENUSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Auto ClockManual ClockOff TimerOn Timer GSleep TimerAuto OffOffOnTime 6 : 30 AMCh. TV 2-0Vol 17MENUSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Auto ClockManual Clock GOff TimerOn TimerSleep TimerAuto OffYear - - - -Date - - / - -Time - - : - - - - MENU- Timer function operates only if current time has been set.- Off-Timer function overrides On-Timer function if they are set both set to the same time.- The TV must be in standby mode for the On-Timer to work.- If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert tostandby mode.On/OfOn/OfffTTimer Setupimer Setup1. Press the MENU button and then use D/Ebutton to select the TIME menu.2. Press the Gbutton and then use D/Ebutton to select Off Timer or On Timer.3. Press the Gbutton and then use D/Ebutton to select On.• To cancel On/Off timer function, select Off.4. Press the Gbutton and then use D/Ebutton to set the hour.5. Press the Gbutton and then use D/Ebutton to set the minutes.6. For only On timer functionPress the Gbutton and then use D/Ebutton to select the channel at turn-on.Press the Gbutton and then use D/Ebutton to set the sound level at turn-on.7. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.Auto Clock SetupAuto Clock Setup- The time is set automatically from a digital channel signal. - The digital channel signal includes information for the current time provided by the broadcasting station.- Set the clock manually, if the current time is set incorrectly by the auto clock function.1. Press the MENU button and then use D/Ebutton to select the TIME menu.2. Press the Gbutton and then use D/Ebutton to select Auto Clock.3. Press the Gbutton and then use D/Ebutton to select On.4. Press the Gbutton and then use D/Ebutton to select your viewing area timezone: Eastern,Central,Mountain,Pacific,Alaska, or Hawaii.5. Press EXIT button to return to TV viewing or press MENU button to return tothe previous menu.Manual Clock SetupManual Clock Setup- If current time setting is wrong, reset the clock manually.1. Press the MENU button and then use D/Ebutton to select the TIME menu.2. Press the Gbutton and then use D/Ebutton to select Manual Clock.3. Press the Gbutton and then use F/Gbutton to select either the year, date, ortime option. Once selected, use the D/Ebutton to set the year, date, and timeoptions.4. Press EXIT button to return to TV viewing or press MENU button to return tothe previous menu.

26 Plasma TVOperationAuto OfAuto Offf- If set to on and there is no input signal, the TV turns off vertically after 10 min-utes.1. Press the MENU button and then use D/Ebutton to select the TIME menu.2. Press the Gbutton and then use D/Ebutton to select Auto Off.3. Press the Gbutton and then use D/Ebutton to select On or Off.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.SleepSleep TTimerimer- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.- You can also set up the Sleep Timer in the TIME menu.1. Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen,followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to countdown from the number of minutes selected.3. To check the remaining minutes before the TV turns off, press the TIMER button once.4. To cancel the Sleep Timer, press the TIMER button repeatedly to select Off.SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Auto ClockManual ClockOff TimerOn TimerSleep TimerAuto Off GOffOnMENU

Owner’s Manual 27OperationOption Menu FeaturesOption Menu FeaturesAspect Ratio ControlAspect Ratio Control- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format.When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be dis-played.- If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option.- Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/DVI-DTV (720p/1080i)/DTV(720p/1080i)input source.- RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.-Note: If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen andremain visible.•Set By ProgramSelects the proper picture proportion to match the source’s image. (4:3 →4:3, 16:9 → 16:9)•4:3Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at boththe left and right sides.•16:9Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.•HorizonChoose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at bothsides, to create a spectacular view.•Zoom 1Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portionsof the picture will be cropped.•Zoom 2Choose Zoom 2 when you want the picture to be altered, both horizontally extended and vertically cropped. Thepicture taking a halfway trade off between alteration and screen coverage.•Cinema ZoomChoose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging orreducing the picture, the image may become distorted. You can adjust the enlarge proportion of Cinema Zoom using D/Ebutton. The adjustment range is 1~16.1. Press the RATIO button repeatedly to select the desired picture format. You can also adjust Aspect Ratio in the OPTION menu.

28 Plasma TVOperationCaption ModeCaption ModeAnalog Broadcasting System Captions- Select a caption mode for displaying captioning information if provided on a program.- Analog caption displays information at any position on the screen usually the program's dialog.- Text displays information, usually at the bottom position and is used for a data service, generally not program related.- Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna 1 source.- This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off.SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Aspect RatioCaptionCaption Mode GCaption OptionLanguageCinemaDemoISM MethodLow PowerMENUCC 1CC 2CC 3CC 4Text 1Text 2Text 3Text 4SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Aspect RatioCaptionCaption Mode GCaption OptionLanguageCinemaDemoISM MethodLow PowerMENUEnglishSpanishFrenchDigital Broadcasting System Captions- Choose the language you want the DTV/CADTV Captions to appear in.- Languages can be chosen for digital sources only if they are included on the program.1. Press the MENU button and then use D/Ebutton to select the OPTION menu.2. Press the Gbutton and then use D/Ebutton to select Caption Mode.3. Press the Gbutton and then use D/Ebutton to select caption: CC1,CC2,CC3,CC4,Text1,Text2,Text3, or Text4.•CAPTIONThe term for the words that scroll across the bottom of the TV screen; usuallythe audio portion of the program provided for the hearing impaired. •TEXTThe term for the words that appear in a large black frame and almost coverthe entire screen; usually messages provided by the broadcaster.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.1. Press the MENU button and then use D/Ebutton to select the OPTION menu.2. Press the Gbutton and then use D/Ebutton to select Caption Mode.3. Press the Gbutton and then use D/Ebutton to select available caption lan-guages: English,Spanish, or French.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.CaptionCaption1. Use the CC button repeatedly to select Caption Off,EZ Mute, or On.•EZ Mute shows the selected captions option (if available on program) when the TV sound is muted.. • You can also use the OPTION menu to select Caption.2. Press EXIT button to save and return to TV viewing.

Owner’s Manual 29OperationOption Menu Features continuedOption Menu Features continuedSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Aspect RatioCaptionCaption ModeCaption Option GLanguageCinemaDemoISM MethodLow PowerStyle CustomSize A StandardFont Font 0Text Color WhiteText Opacity Solid Bg Color BlackBg Opacity SolidEdge Type NoneEdge Color BlackMENUCaption OptionCaption Option- Customize the DTV/CADTV captions that appear on your screen.1. Press the MENU button and then use D/Ebutton to select the OPTIONmenu.2. Press the Gbutton and then use D/Ebutton to select Caption Option.3. Press the Gbutton and then use F/Gbutton to select Custom.4. Use D/Ebutton to customize the Style, Font, etc., to your preference. A pre-view icon is provided at the bottom of the screen, use it to see the caption lan-guage.•Size: Set the size the words will appear in.•Font: Select a typeface for the words.•Text Color: Choose a color for the text.•Text Opacity: Specify the opacity for the text color.•Bg (Background) Color: Select a background color.•Bg (Background) Opacity: Select the opacity for the background color.•Edge Type: Select an edge type.•Edge Color: Select a color for the edges.5. Press EXIT button to return to TV viewing or press MENU button to returnto the previous menu.SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.MENUCinema Mode Setup- Set up the TV for the best picture appearance for viewing movies.1. Press the MENU button and then use DD/Ebutton to select the OPTION menu.2. Press the Gbutton and then use D/Ebutton to select Cinema.3. Press the Gbutton and then use D/Ebutton to select On or Off.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.-EZ Demo Use to scan the features and menu options available on your TV.-XD Demo Use to see the difference between XD Demo On and XD Demo Off.1. Press the MENU button and then use D/Ebutton to select the OPTION menu.2. Press the Gbutton and then use D/Ebutton to select Demo.3. Press the Gbutton and then use D/Ebutton to select EZ Demo or XD Demo.4. Press the Gbutton to start EZ Demo or XD Demo. Press EXIT button to stop EZDemo or XD Demo.DemoDemoSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Aspect RatioCaptionCaption ModeCaption OptionLanguageCinemaDemo GISM MethodLow PowerMENUEZ DemoDemoOffOnAspect RatioCaptionCaption ModeCaption OptionLanguageCinema GDemoISM MethodLow Power

30 Plasma TVOperationLow PowerLow Power- Low power reduces the plasma display's power consumption.1. Press the MENU button and then use D/Ebutton to select the OPTION menu.2. Press the Gbutton and then use D/Ebutton to select Low power.3. Press the Gbutton and then use D/Ebutton to select On or Off.• If you select On, the screen darkens.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.SETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Aspect RatioCaptionCaption ModeCaption OptionLanguageCinemaDemoISM Method GLow PowerMENUNormalOrbiterInversionWhite WashSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Aspect RatioCaptionCaption ModeCaption OptionLanguageCinemaDemoISM MethodLow Power GMENUOffOn1. Press the ZOOM button in DTV 720p, or 1080i modes.2. Use the D/E/F/Gbuttons to select the screen split zoom section.3. To return to normal viewing, press the ZOOM button again.Split Zoom (DTV 720p, or 1080i mode only)Split Zoom (DTV 720p, or 1080i mode only)- Enlarges the picture with correct proportions.- When enlarging the picture, the image may become distorted.FFFF- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghostimage remaining; even when you change the image. Avoid allowing any fixed image to remain on the TV's screenfor a long period of time.1. Press the MENU button and then use D/Ebutton to select the OPTION menu.2. Press the Gbutton and then use D/Ebutton to select ISM Method.3. Press the Gbutton and then use D/Ebutton to select either Normal,Orbiter,Inversion, or White Wash.•NormalIf image sticking is never a problem, ISM is not necessary - set to Normal.When image is stopped, screen light automatically get dark to prevent ghostimages, and image is appeared, screen light get bright,automatically.•OrbiterOrbiter may help prevent ghost images. However, it is best not to allow anyfixed image to remain on the screen. To avoid a permanent image on thescreen, the image will move once per minute: Right →Right → Downside →Downside →Left →Left→Upside →Upside.•InversionInversion will automatically invert the plasma display panel color every 30 min-utes.•White WashWhite Wash remove s permanent images from the screen. Note: An excessivepermanent image may be impossible to clear entirely with White Wash. Toreturn to normal viewing, press the any button.4. Press EXIT button to return to TV viewing or press MENU button to return tothe previous menu.ISM (Image Sticking Minimization) MethodISM (Image Sticking Minimization) Method

Owner’s Manual 31OperationLock Menu OptionsLock Menu OptionsParental Control can be used to block specific channels, ratings and other viewing sources.The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station.The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categorieschosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must bedone :1. Set ratings and categories to be blocked.2. Specify a password3. Enablethe lockV-Chip rating and categoriesRating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TVRating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie RatingSystem (MPAA) only.Ratings for Movies previously shown in theaters:Movie Ratings :• Blocking Off (Permits all programs)• G (General audience)• PG (Parental guidance suggested)• PG-13 (Parents strongly cautioned)• R (Restricted)• NC-17 (No one 17 and under admitted)• X (Adult only)If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.Ratings for Television programs including made-for-TV movies :• TV-G (General audience)• TV-PG (Parental guidance suggested)• TV-14 (Parents strongly cautioned)• TV-MA (Mature audience only)• TV-Y (All children)• TV-Y7 (Children 7 years older)TV Rating Children:• Age (applies to TV-Y, TV-Y7)• Fantasy Violence (applies to TV-Y7)TV Rating General:• Age (applies to TV-G, TV-PG, TV-14, TV-MA)• Dialogue - sexual dialogue (applies to TV-PG, TV-14)• Language - adult language (applies to TV-PG, TV-14, TV-MA)• Sex - sexual situations (applies to TV-PG, TV-14, TV-MA)• Violence (applies to TV-PG, TV-14, TV-MA)Aux. Block• Video 1, 2 (On, Off)• Component 1, 2 (On, Off)• RGB, DVI (On, Off)

32 Plasma TVOperationParental Lock SetupParental Lock Setup1. Press the MENU button and then use D/Ebutton to select the LOCK menu.Then, press the Gbutton• If Lock is already set, enter the password as requested.• The TV is set up with the initial password “7-7-7-7”.2. Use the D/Ebutton to choose from the following Lock Menu options. Once theoption is selected, change the settings to your preference.•Lock System: Activates or disables the blocking scheme you set up previ-ously.•Set Password: Change the password by inputting a new password twice. •Movie Rating (MPPA): Blocks movies according to the movie ratings limitsspecified, so children cannot view certain movies. You can set the ratingslimit by blocking out all the movies with the ratings above a specified level.Keep in mind that the movie ratings limit only applies to movies shown onTV, not TV programs, such as soap operas.•TV Rating-Children: Prevents children from watching certain children's TVprograms, according to the ratings limit set. The children rating does notapply to other TV programs. Unless you block certain TV programs intend-ed for mature audiences in the TV Rating - sub menu, your children canview those programs.•TV Rating-General: Based on the ratings, blocks certain TV programs thatyou and your family do not want to view.•Aux. Block: Enables you to select a source to block from the externalsource devices you have hooked up.3. Press EXIT button to return to TV viewing or press MENU button to return tothe previous menu.Note• If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control.- Lets you set up blocking schemes to block specific channels, ratings, and external viewing sources.- A password is required to gain access to this menu if the Lock System is turned onSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.Lock System GSet PasswordBlock Ch.Movie RatingTV Rating-ChildrenTV Rating-GeneralAux. BlockMENUOffOn

Owner’s Manual 33OperationWWatching PIP/POP/Tatching PIP/POP/Twin Picturewin Picture- PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the othersource will show a smaller inset image.- Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Eachsource is given half the screen.- If you set the block/rating for Lock menu options in PIP/Twin Picture mode, “Rating Blocked” doesn’t display on screen.Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below.PIP OffPIP Mode POP Mode Twin Picture ModePIPPIP (Picture-In-Picture) / POP(Picture-In-Picture) / POP / T/ Twin Picturewin PictureTV Program Selection for PIPTV Program Selection for PIP1. Press the PIP button.2. Select the Analog or DTV option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+ /PIPCH- button to select a channel for the sub picture.Swapping the PIPSwapping the PIP/T/Twin Picturewin PictureUse the SWAP button to switch the main and sub pictures.• Component 1, Component 2, RGB-PC (or RGB-DTV), DVI-DTV (or DVI-PC) input sources for the main picture can’tbe used to swap the main and sub pictures.Selecting an Input Signal Source for PIP/TSelecting an Input Signal Source for PIP/Twin Picturewin PictureUse the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changesthe PIP source. You can also select sources for the Sub Input in the SETUP menu.Main Picture Source Available Sub Picture SourcesDTV SignalAnalog SignalAnalog, Video 1, and Video 2DTV, Analog, Video 1, and Video 2Main Picture Sub Picture Main Picture Sub PictureFTV 2-0TV 4-0TV 6-0ED

34 Plasma TVOperationMoving the PIPMoving the PIP sub picturesub pictureIn PIP mode, press the D/E/F/Gbutton to move the sub picture to a different location on thescreen.Adjusting Main and Sub Picture Sizes for Adjusting Main and Sub Picture Sizes for TTwin Picturewin PictureUse the D/E/F/Gbutton to change main and sub picture sizes in Twin Picture mode.If the maximal adjustedscreen is 4:3, the largescreen is filled with entirescreen vertically as shown.If the maximal adjustedscreen is 16:9, the largescreen appears the graypart at both the up anddown sides.i.e)1. Press the PIP button to activate the POP mode while in PIP mode. •Channel selection: Use Fbutton to enlarge the selected channel being searched on the PIPscreen to shift it for viewing on the Main screen. •PIP selection: Use D/Ebutton to select one of 3 PIP screen pictures in POP mode.•Input source selection for PIP: Use PIP INPUT button or Sub Input option on the SETUPmenu to select an input source for the sub picture (You can’t select DTV for main and sub pic-ture simultaneously). You can only select the Analog and DTV signal for sub input source inPOP mode.2. Press the EXIT button to cancel POP mode.POPPOP (Picture-out-of-Picture: Channel Scan)(Picture-out-of-Picture: Channel Scan)- Use POP to search the programs of all the memorized channels one-by-one on the 3 PIP screen display,(while the main picture source remains the current channel). The pictures of all the programmed channelsare searched with the 3 POP screen.- Note: Run EZ Scan channel search before using POP mode.FTV 2-0TV 4-0TV 6-0ED

Owner’s Manual 35External Control Device SetupNo. Pin Name1 No connection2 RXD (Receive data)3 TXD (Transmit data)4 DTR (DTE side ready)5 GND6 DSR (DCE side ready)7 RTS (Ready to send)8 CTS (Clear to send)9 No Connection15692354678RXDTXDGNDDTRDSRRTSCTSTXDRXDGNDDSRDTRCTSRTSPC7-Wire Configurations(Standard RS-232C cable)D-Sub 93256487PDPD-Sub 92354678RXDTXDGNDDTRDSRRTSCTSTXDRXDGNDDTRDSRRTSCTSPC3-Wire Configurations(Not standard)D-Sub 93254678PDPD-Sub 9- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)and control the Monitor’s functions externally.- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.- RS-232C connection cables are not supplied with the Monitor.TType of Connector; D-Sub 9-Pin Maleype of Connector; D-Sub 9-Pin MaleRS-232C ConfigurationsRS-232C ConfigurationsExternal Control Device SetupExternal Control Device SetupRS-232C SetupRS-232C SetupREMOTECONTROLRS-232C INPUT(CONTROL/SERVICE)AC INPUTAUDIO INPUTCOMPONENT 2COMPONENT 1RLDIGITAL AUDIO(OPTICAL)DVIINPUTCOMPONENT1INPUTOUTPUTAUDIO INPUTDVI INPUT(PC/DTV INPUT)RGB INPUT(PC/DTV INPUT)VIDEO INPUTMONITOROUTPUTA/VINPUT 1AUDIOR L(MONO)VIDEOAntenna 1Analog/DTVAntenna 2 DTVS-VIDEODVDDTVINPUT.PC

36 Plasma TVExternal Control Device SetupSet IDSet IDUse this function to specify a monitor ID number. Refer to ‘Real Data Mapping’. See page 37.• Baud rate : 9600 bps (UART)• Data length : 8 bits• Parity : None* Use a crossed (reverse) cable.• Stop bit : 1 bit• Communication code : ASCII codeCommunication ParametersCommunication Parameters1. Press the MENU button and then use D/Ebutton to select the SETUP menu.2. Press the Gbutton and then use D/Ebutton to select SET ID.3. Press the Gbutton and then use D/Ebutton to adjust SET ID to choose thedesired monitor ID number. The adjustment range of SET ID is 1 ~ 99.4. Press EXIT button to return to TV viewing or press MENU button to return to theprevious menu.Transmission*[Command 1]: First command to control the set. (j or k)*[Command 2]: Second command to control the set.*[Set ID]: You can adjust the set ID to choose desired monitorID number in Setup menu. Adjustment range is 1~ 99. When selecting Set ID ‘0’, every connectedthe TV is controlled. Set ID is indicated as decimal(1~99) on menu and as Hexa decimal (0x0~0x63)on transmission/receiving protocol.*[DATA]: To transmit command data.Transmit ‘FF’ data to read status of command.*[Cr]: Carriage ReturnASCII code ‘0x0D’*[ ]: ASCII code ‘space (0x20)’[Command1][Command2][ ][Set ID][ ][Data][Cr]TTransmission / Receiving Protocolransmission / Receiving ProtocolOK Acknowledgement* The Monitor transmits ACK (acknowledgement) based onthis format when receiving normal data. At this time, if thedata is data read mode, it indicates present status data. Ifthe data is data write mode, it returns the data of the PCcomputer.[Command2][ ][Set ID][ ][OK][Data][x]Error Acknowledgement* The Monitor transmits ACK (acknowledgement) based onthis format when receiving abnormal data from non-viablefunctions or communication errors.[Command2][ ][Set ID][ ][NG][Data][x]Data 1: Illegal Code2: Not supported function3: Wait more time01. Power k a 0 ~ 102. Input Select k b 0 ~ 903. Aspect Ratio k c 0 ~ 1504. Screen Mute k d 0 ~ 105. Volume Mute k e 0 ~ 106. Volume Control k f 0 ~ 6407. Contrast k g 0 ~ 6408. Brightness k h 0 ~ 6409. Color k i 0 ~ 6410. Tint k j 0 ~ 6411. Sharpness k k 0 ~ 6412. OSD Select k l 0 ~ 113.Key Lock Mode k m 0 ~ 114. PIP/POP/Twin Picture k n 0 ~ 315. PIP Position k q 0 ~ 316. Treble k r 0 ~ 6417. Bass k s 0 ~ 6418. Balance k t 0 ~ 6419. Color Temperature k u 0 ~ 220. PIP Input Source k y 0 ~ 321. ISM Method j p 0 ~ 222. White Wash j q 0 ~ 123. Orbiter Time Setting j r 1 ~ 6424. Orbiter Pixel Setting j s 0 ~ACOMMAND 1 COMMAND 2 DATA(Hexadecimal)25. Channel Tuning m a 01 ~ 87 01 ~ 87 00 ~ FE 00 ~ 1526. Channel Add/Del m b 00 ~ 0127. Key m cCOM-MAND 2COM-MAND 1DATA 0(Hexadecimal)DATA 1(Hexadecimal)DATA 2(Hexadecimal)DATA 3(Hexadecimal)Command Reference ListCommand Reference ListSETUPVIDEOAUDIOTIMEOPTIONLOCK Prev.EZ ScanCh.EditDTV SignalCh. LabelMain InputSub InputSET ID GMENU1

Owner’s Manual 37External Control Device Setup02. Input Select (Command2:b) (Main Picture Input)GTo select input source for the Monitor.TransmissionData 0: DTV1: Analog2: Video 13: Video 24: Component 15: Component 26: RGB-DTV7: RGB-PC8: DVI-DTV9: DVI-PCData 0: Auto (Set by program)1: Normal screen (4:3)2: Wide screen (16:9)3: Horizon4: Zoom 15: Zoom 26: Cinema Zoom (1)15: Cinema Zoom (16)[k][b][ ][Set ID][ ][Data][Cr]Acknowledgement[b][ ][Set ID][ ][OK][Data][x]01. Power (Command2:a)GTo control Power On/Off of the Monitor.TransmissionData 0 : Power Off 1 : Power On[k][a][ ][Set ID][ ][Data][Cr]Acknowledgement[a][ ][Set ID][ ][OK][Data][x]* In a like manner, if other functions transmit ‘FF’ databased on this format, Acknowledgement data feedbackpresents status about each function.*Real data mapping0 : Step 0A : Step 10 (SET ID 10)F : Step 15 (SET ID 15)10 : Step 16 (SET ID 16)64 : Step 10005. Volume Mute (Command2:e)GTo control volume mute on/off.You can also adjust mute using the MUTE button onremote control.TransmissionData 0 : Volume mute off (Volume on)1 : Volume mute on (Volume off)[k][e][ ][Set ID][ ][Data][Cr]Acknowledgement[e][ ][Set ID][ ][OK][Data][x]03. Aspect Ratio (Command2:c) (Main picture format)GTo adjust the screen format.You can also adjust the screen format using the RATIObutton on remote control or in the Option menu.Transmission[k][c][ ][Set ID][ ][Data][Cr]Acknowledgement[c][ ][Set ID][ ][OK][Data][x]04. Screen Mute (Command2:d)GTo select screen mute on/off.TransmissionData 0 : Screen mute off (Picture on)1 : Screen mute on (Picture off)[k][d][ ][Set ID][ ][Data][Cr]Acknowledgement[d][ ][Set ID][ ][OK][Data][x]06. Volume Control (Command2:f)GTo adjust volume.You can also adjust volume with the volume buttonson remote control.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping’ as shown below.[k][f][ ][Set ID][ ][Data][Cr]Acknowledgement[f][ ][Set ID][ ][OK][Data][x]07. Contrast (Command2:g)GTo adjust screen contrast. You can also adjust contrast in the Video menu.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping’ as shown below.[k][g][ ][Set ID][ ][Data][Cr]Acknowledgement[g][ ][Set ID][ ][OK][Data][x]08. Brightness (Command2:h)GTo adjust screen brightness.You can also adjust brightness in the Video menu.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping’ as shown below.[k][h][ ][Set ID][ ][Data][Cr]Acknowledgement[h][ ][Set ID][ ][OK][Data][x]

38 Plasma TVExternal Control Device Setup09. Color (Command2:i)GTo adjust the screen color.You can also adjust color in the Video menu.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping’. See page 37.[k][i][ ][Set ID][ ][Data][Cr]Acknowledgement[i][ ][Set ID][ ][OK][Data][x]10. Tint (Command2:j)GTo adjust the screen tint.You can also adjust tint in the Video menu.TransmissionData Red : 0 ~ Green : 64•Refer to ‘Real data mapping’. See page 37.[k][j][ ][Set ID][ ][Data][Cr]Acknowledgement[j][ ][Set ID][ ][OK][Data][x]13. Remote Control Lock Mode (Command2:m)GTo lock the remote control and the front panel controls onthe set.Transmission[k][m][ ][Set ID][ ][Data][Cr]AcknowledgementData 0: Lock off 1: Lock on[m][ ][Set ID][ ][OK][Data][x]14. PIP / POP / Twin Picture (Command2:n)GTo control the PIP (Picture-in-Picture)/POP/Twin picture.You can also control the PIP/POP/Twin picture using thePIP button on the remote control.TransmissionData 0: PIP off1: PIP2: POP3: Twin Picture[k][n][ ][Set ID][ ][Data][Cr]Acknowledgement[n][ ][Set ID][ ][OK][Data][x]GTo adjust the screen sharpness.You can also adjust sharpness in the Video menu.Transmission11. Sharpness (Command2:k)Data Min: 0 ~ Max: 64•Refer to ‘Real data mapping’. See page 37.[k][k][ ][Set ID][ ][Data][Cr]Acknowledgement[k][ ][Set ID][ ][OK][Data][x]12. OSD Select (Command2:l)GTo select OSD (On Screen Display) on/off.Transmission[k][l][ ][Set ID][ ][Data][Cr]AcknowledgementData 0: OSD off 1: OSD on[l][ ][Set ID][ ][OK][Data][x]15. PIP Position (Command2:q)GTo select sub picture position for PIP.Transmission[k][q][ ][Set ID][ ][Data][Cr]AcknowledgementData 0: Right down on screen1: Right up on screen2: Left up on screen3: Left down on screen[q][ ][Set ID][ ][OK][Data][x]16. Treble (Command2:r)GTo adjust treble.You can also adjust treble in the Audio menu.TransmissionData Min: 0 ~ Max: 64•Refer to ‘Real data mapping’. See page 37.[k][r][ ][Set ID][ ][Data][Cr]Acknowledgement[r][ ][Set ID][ ][OK][Data][x]18. Balance (Command2:t)GTo adjust balance.You can also adjust balance in the Audio menu.TransmissionData Min: 0 ~ Max: 64•Refer to ‘Real data mapping’. See page 37.[k][t][ ][Set ID][ ][Data][Cr]Acknowledgement[t][ ][Set ID][ ][OK][Data][x]17. Bass (Command2:s)GTo adjust bass.You can also adjust bass in the Audio menu.TransmissionData Min: 0 ~ Max: 64•Refer to ‘Real data mapping’. See page 37.[k][s][ ][Set ID][ ][Data][Cr]Acknowledgement[s][ ][Set ID][ ][OK][Data][x]

Owner’s Manual 39External Control Device Setup19. Color Temperature (Command2:u)GTo adjust color temperature.You can also adjust color temperature in the Videomenu.TransmissionData 0: Warm 1: Medium 2: Cool[k][u][ ][Set ID][ ][Data][Cr]Acknowledgement[u][ ][Set ID][ ][OK][Data][x]23. Orbiter Time Setting (Command2:r)GTo adjust orbiter operation time term.TransmissionData Min: 1 ~ Max: 64•Refer to ‘Real data mapping’. See page 37.[j][r][ ][Set ID][ ][Data][Cr]Acknowledgement[r][ ][Set ID][ ][OK][Data][x]24. Orbiter Pixel Setting (Command2:s)GTo adjust pixel number in orbiter function.TransmissionData Min: 0 ~ Max: A[j][s][ ][Set ID][ ][Data][Cr]Acknowledgement[s][ ][Set ID][ ][OK][Data][x]25. Channel Tuning (Command: m a)GTo tune channel to following physical/major/minor numberTransmissionData 0: Physical channel number (Transmit by Hexadecimal code)* NTSC air: 02 ~ 45NTSC cable: 01, 0E ~ 7DATSC air: 01 ~ 45ATSC cable: 01 ~ 871:Major channel number (Transmit by Hexadecimal code)* NTSC air: 02 ~ 45, NTSC cable: 01 ~ 7DATSC air: 01 ~ 63, ATSC cable: 01 ~ 872:Minor channel number (Transmit by Hexadecimal code)* NTSC air: 00 (must be 0), ATSC: 01 ~ FE3: High nibble →Main picture: 0, Sub picture (PIP): 1Low nibble →NTSC air: 0, NTSC cable: 1, ATSC: 2,Example) If you want PIP channel tuned to ATSC cable (stan-dard) 30-5, the command sequence is ma 00 1e 1e 05 12.•Refer to ‘Real data mapping’. See page 37.* To change the channel between ATSC air and ATSC cable,change the antenna setting with EZ Scan.[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][Cr][a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][x][a][ ][Set ID][ ][NG][Data0][x]Acknowledgement26. Channel Add/Del (Command: m b)GTo add and delete the channelsTransmissionData 0: Channel Delete1: Channel Add[m][b][ ][Set ID][ ][Data][Cr][b][ ][Set ID][ ][OK][Data][x][b][ ][Set ID][ ][NG][Data][x]Acknowledgement27. Key (Command: m c)GTo send IR remote key codeTransmissionData Key code: Refer to page 41.* It’s impossible to command the IR Code 0x08 and 0xC4with RS-232C. [m][c][ ][Set ID][ ][Data][ ][Cr][c][ ][Set ID][ ][OK][Data][x]Acknowledgement20. PIP Input Select (Command2:y)GTo select input source for sub picture in PIP/Twin pic-ture mode.TransmissionData 0: DTV1: Analog2: Video 13: Video 2[k][y][ ][Set ID][ ][Data][Cr]Acknowledgement[y][ ][Set ID][ ][OK][Data][x]21. ISM Method (Command2:p)GTo avoid having a fixed image remain on screen.TransmissionData 0: Normal1: Orbiter2: Inversion[j][p][ ][Set ID][ ][Data][Cr]Acknowledgement[p][ ][Set ID][ ][OK][Data][x]22. White Wash (Command2:q)GTo control the white wash function on/off.You can also adjust white wash in Option menu.TransmissionData 0: White Wash off1: White Wash on[j][q][ ][Set ID][ ][Data][Cr]Acknowledgement[q][ ][Set ID][ ][OK][Data][x]

40 Plasma TVIR CodesGConnect your wired remote control to the Remote Control port on the TV. GOutput waveformSingle pulse, modulated with 37.917KHz signal at 455KHzGConfiguration of frameGRepeat codeGLead code•1st frameLowcustom codeLeadcodeHighcustom code Data code Data codeTCTfT1C0Carrier frequencyFCAR = 1/TC= fOSC/12Duty ratio = T1/TC= 1/3•Repeat frameC1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7Repeat code9 ms 4.5 ms0.55 ms9 ms2.25 msGBit descriptionGFrame interval : TfThe waveform is transmitted as long as a key is depressed.•Bit “0”Tf TfTf=108ms @455KHz0.56 ms 0.56 ms1.12 ms•Bit “1”2.24 msHow to ConnectHow to ConnectRemote Control IR CodesRemote Control IR CodesIR CodesIR Codes

Owner’s Manual 41IR Codes0x0B0x080xC40xC50x980x790x0E0x10 ~ 0x190x4C0x1A0x090x020x030x000x010x1E0xAA0x390x400x410x070x060x440x430x520x4D0x5B0x600x720x710x610x630x650x7B0x0A0xCB0xD60x5A0xD00xBF0xD40xD50xD70xC60x760x770xAF0x700x96R/C ButtonR/C ButtonR/C Button (Power On/Off)Discrete IR Code (Only Power On)Discrete IR Code (Only Power Off)R/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonDiscrete IR Code (TV Input Selection)Discrete IR Code (Video1 Input Selection)Discrete IR Code (Video2 Input Selection)Discrete IR Code (Component1 Input Selection)Discrete IR Code (Component2 Input Selection)Discrete IR Code (RGB-PC Input Selection)Discrete IR Code (RGB-DTV Input Selection)Discrete IR Code (DVI-DTV Input Selection)Discrete IR Code (Only 4:3 Mode)Discrete IR Code (Only 16:9 Mode)Discrete IR Code (Only Zoom Mode)Channel SearchR/C ButtonCode (Hexa) Function NoteTV/VIDEOMODEPOWERPOWER ONPOWER OFFCOMP/RGB/DVIRATIOTIMERNumber Key 0~ 9- (Dash)FLASHBKMUTEVOL +VOL -CH +CH -SURFINFOCCDEFGOKMENUSOUNDVIDEOEXITPIPPIPCH -PIPCH +PIP INPUTSWAPFREEZEZOOMSAPADJUSTTVVIDEO 1VIDEO 2COMPONENT 1COMPONENT 2RGB-PCRGB-DTVDVI-DTVRatio 4:3Ratio 16:9Ratio ZoomMULTI PIPSIGNAL

Owner’s Manual 45Troubleshooting ChecklistNo output from one ofthe speakers • Adjust Balance in the AUDIO menu. (Refer to p.23)Unusual sound frominside the TV• A change in ambient humidity or temperature may result in an unusual noisewhen the plasma display is turned on or off and does not indicate a fault withthe TV.No picture &No sound• Check whether the TV is turned on.• Is the power cord inserted into wall power outlet?• Test the wall power outlet, plug another product’s power cord into the outletwhere the TV’s power cord was plugged in.No or poor coloror poor picture• Select Color in the Video menu and press the Gbutton.(Refer to p.21)• Keep a sufficient distance between the TV and the VCR.• Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the screen gets dark.) The remote control doesn’t work• Check to see if there is any object between the TV and the remote controlcausing obstruction.• Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.9) • Correct remote operating mode set: TV, VCR etc.?• Install new batteries. (Refer to p.9)Picture OK &No sound• Press the VOLUME (G) button.• Sound muted? Press MUTE button.Picture appears slowlyafter switching on• This is normal, the image is muted during the TV startup process. Pleasecontact your service center, if the picture has not appeared after five minutes.Horizontal/vertical barsor picture shaking • Check for local interference such as an electrical appliance or power tool.TTroubleshooting Checklistroubleshooting Checklist

46 Plasma TVMaintenance & Specification• The specifications shown above may be changed without prior notice for quality improvement.Product SpecificationsProduct SpecificationsMODELAC100-240V ~ 50/60HzNTSC-M, ATSCVHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125, CADTV 1 ~ 135. DTV 2 ~ 6975 Ω1024 x 768 (Dot) 16,770,000 (256 steps of each R, G and B)32 ~ 104°F (0 ~ 40°C)Less than 80%6561 feet (2000m)41 / 121027.5 / 7013.7 / 9676.1 / 34.6Width (inches / mm)Height (inches / mm)Depth (inches / mm)Weight (pounds / kg)Power requirementTelevision SystemProgram CoverageExternal Antenna ImpedanceResolutionColorOperating Temperature RangeOperating Humidity RangeMaximum ElevationDU-42PX12XD1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water anda little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe thescreen.2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.Please be sure not to use a wet cloth.If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplugthe power cord to protect against possible damage from lightning or power surges.- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have yournew TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.Cleaning the ScreenCleaning the ScreenCleaning the CabinetCleaning the CabinetExtendedExtended AbsenceAbsenceMaintenanceMaintenance