LG Electronics USA E2770VV LED LCD Monitor User Manual G User s manual

LG Electronics USA LED LCD Monitor G User s manual

User Manual

Order Number : GETEC-C1-10-215 FCC Part 15 subpart B Test Report Number : GETEC-E3-10-111 Page 1 / 1 EUT Type: LED LCD Monitor FCC ID.: BEJE2770VV APPENDIX G : USER’S MANUAL
OWNER’S MANUALLED LCD MONITOR LED LCD MONITOR MODELSE2370VE2770Vwww.lg.comPlease read this manual carefully before operatingyour set and retain it for future reference.ENGLISH
1Important PrecautionsThis unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, use, and servicing.On SafetyUse only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.The appliance coupler is used as the disconnect device.Please make sure the device is installed near the wall outlet to which it isconnected and that the outlet is easily accessible.Operate the display only from a power source indicated in the specifications of thismanual or listed on the display. If you are not sure what type of power supply youhave in your home, consult with your dealer.Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call yourservice technician for replacement.As long as this unit is connected to the AC wall outlet, it is not disconnected fromthe AC power source even if the unit is turned off.Do not Open the Display:There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.Do not drop an object on or apply impact to the product. Do not throw any toysor objects on the product screen. It can cause injury to human, problem to product and damage the display. To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.When the display is to be left unattended for an extended period of time, unplugit from the wall outlet.In the presence of thunder and lightning, never touch the power cord and signalcable because it can be very dangerous. It can cause electric shock.
2Important PrecautionsOn InstallationDo not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage.Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.Do not press the LCD screen with your finger for a long time as this may causesome afterimages.Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.Leaving a fixed image on the screen for a long time may cause damage to thescreen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity.
Important Precautions3On CleaningUnplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.When cleaning the product, unplug the power cord and scrub gently with a softcloth to prevent scratching. Do not clean with a wet cloth or spray water or otherliquids directly onto the product. An electric shock may occur. (Do not usechemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining. On RepackingDo not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.On Disposal (Only , Hg lamp used LCD Monitor)The fluorescent lamp used in this product contains a small amount of mercury.Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations ofyour local authority.
4AccessoriesOwner's Manual/Cards Power Cord15-pin D-Sub Signal Cable DVI-D Signal Cable(This feature is not available inall countries.)NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferritecores to maintain standard compliance for the product.(Depending on the country)!!! Thank you for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer.Remote controlPrimary Cell Battery, Lithium
Connecting the Display5Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.Connecting the stand 1.Place the monitor face down on the cushion or soft cloth.3.Use a Coin on the bottom of the stand base and turn screw clockwise to tighten.4.Once assembled take the monitor up carefully and face the front side.2.Assemble the Stand Base into the Stand Body in the correct direction as shown in the picture. Stand BaseStand BodyTurn the screwby using a Coin.
6Connecting the DisplayIMPORTANTThis illustration depicts the general model of connection. Your monitor may differ from the itemsshown in the picture.Do not carry the product upside down holding only the stand base. The product may fall and getdamaged or injure your foot.Detach the monitor to the Stand Base by turning thescrew to the left. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. Positioning your displayAdjust the position of the panel in various ways for maximum comfort.Tilt Range : -5˚ to 15˚ 15-5 IMPORTANTIt is recommended that in order to maintain an ergonomic andcomfortable viewing position, the forward tilt angle of the monitorshould not exceed 5 degrees.Do not touch or press the screen when adjusting the angle of the monitor.
7Connecting the DisplayABConnect DVI-D(Digital signal) CableConnect D-sub(Analog signal) Cable Connect HDMI Cable1. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. 2.Connect signal input cable and power cord in order, then tighten the screwof the signal cable. Connecting with the PC 12NOTE This is a simplified representation of the rear view.This rear view represents a general model; your display may differ from the view as shown.CDVI-D (This feature is notavailable in all countries.)Connect the signalinput cable andtighten it up byturning in thedirection of thearrow as shown inthe figure.Mac adapter : For Apple Macintosh use,a separate plug adapter is needed tochange the 15 pin high density (3 row) D-sub VGA connector on the supplied cableto a 15 pin 2 row connector.When using a D-Sub signal input cableconnector for Macintosh AV equipment(Set-Top Box, DVD,Video, Video GameConsole)* HDMI is optimized on the AV equipment.* Not supported PCVaries according to model.Headphone/Earphone outputWall-outlet type
8Connecting the DisplayNOTE‘ Self Image Setting Function’? This function provides the user with optimal displaysettings.When the user connects the monitor for the first time, this function automatically adjuststhe display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screenflicker or tilted screen while using the device or after changing screen resolution, press theAUTO function button to improve resolution. 3. Press the power button on the bottom right of the monitor to turn the power on. Whenmonitor power is turned on, the 'Self Image Setting Function' is executedautomatically. (Only Analog Mode)Power Button
Remote Control Functions 9Remote Control ControlsUse this button to turn the displayon or off.Button Use this button to select the input signal.(D-SUB/DVI-D/HDMI1/HDMI2)Input Button Use this button to select the UserMode. User ModeButton Use Aspect Ratio control.Aspect RatioButton Use Frame-Buffer to prevent picture delay.Thru ModeButton Use Super+ Resolutioncontrol.Super Res.Button Use this button to select the PIPfunction.PIP Button Use this button to switch betweenthe main screen and the PIPscreen.Swap Button To adjust the brightness.BrightnessButton To adjust the volume.(Use for the HDMI input)VolumeButton To select the mute.(Use for the HDMI input)Button Replacing the Remote Control Battery1. Take out the battery cap.2. Replace the battery (CR 2032 3V) with the + side facing up.3. Close the battery cap.* Use a coin to open or close the battery cover.
10INPUT ButtonWhen two input signals at least are connected, you canselect the input signal (D-SUB/DVI-D/HDMI1/HDMI2) youwant. When only one signal is connected, it is automaticallydetected. The default setting is D-Sub. (SOURCE Hot key)Control Panel Functions Front Panel ControlsG-MODE ButtonUse this button to enter USER MODE, THRU MODE, SUPER+RESOLUTION, ASPECT RATIO or AUTO BRIGHT menus. For more information, refer to page 15 to 20.INPUTOKOKINPUTINPUTOKOKINPUTOKINPUTOKINPUTOKD-SUBD-SUBD-SUBD-SUBD-SUBDVI-DDVI-DDVI-DDVI-DDVI-D
11Control Panel FunctionsAUTO ButtonAUTO IMAGE ADJUSTMENTWhen adjusting your display settings, always pressthe AUTO button before entering the On ScreenDisplay(OSD). (Only Analog Mode)This will automatically adjust your display image tothe ideal settings for the current screen resolutionsize (display mode).The best display mode is1920 x 1080 Use this button to turn the display on or off.The power indicator stays red if the display is runningproperly (On Mode). If the display is in Sleep Mode(Energy Saving), the power indicator is blinking red. Power Button &Power IndicatorExit the OSD(On Screen Display).EXIT Button MENU ButtonOSD LOCKED/UNLOCKEDThis function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.You can unlock the OSD controls at any time by pushingthe MENU button for several seconds. The message"OSD UNLOCKED" should appear.Use this button to enter or exit from the On Screen Display.To adjust the headphone/ earphone volume.(Only HDMI Mode)VOLUME Button
12On Screen Display (OSD) Control Adjustment Screen AdjustmentMaking adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The following section is an outline of the availableadjustments and selections you can make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the discretionary button, then the main menu of the OSD appears.(except for the power button)To access a control, use the corresponding buttons.Use the / buttons to adjust the image to the desired level. Use the button to select other sub-menu items.Press the EXIT Button to exit from the OSD. G-MODE USER MODE1MODE 1MODE 1MODE 12MODE 2MODE 2MODE 23MODE 3MODE 3MODE 3G-MODE USER MODENORMALNORMAL MODE 1MODE 1 MODE 2MODE 2 MODE 3MODE 31234
13On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus.: D-SUB(Analog signal) input : DVI-D(Digital signal) input: HDMI signalD-SUBDVI-DHDMIUSER MODETHRU MODESUPER+ RESOLUTIONASPECT RATIOAUTO BRIGHTG-MODEUse this menu to select the User Mode.With the picture improvementtechnology that minimizes thedegradation of picture qualitydue to enlargement (e.g.blurred focus and unsharpedge), resolution is notcompromised even whenimages are enlarged, thusguaranteeing a clear image.Use this menu to adjust theaspect ratio of a picturedisplayed on the screen.Use this menu to adjust thescreen brightnessautomatically.To prevent picture delay, framebuffer (video memory) is notused in this mode.D-SUBDVI-DHDMIMain menu Sub-menu Supported inputDescriptionD-SUBDVI-DHDMI 1HDMI 2INPUTDSUBDVI-DHDMIUse this button to select the inputsignal. (D-SUB/DVI-D/HDMI1/HDMI2)COLOR TEMP GAMMAHUESATURATIONCOLOR RESETCOLOR To customize the color of thescreenDVI-DHDMIREDGREENBLUE(PRESET) (USER)sRGB5000K6500K 7200K8200K 9300KD-SUBBRIGHTNESSCONTRASTSHARPNESSBLACK LEVELPICTURE Use this menu to adjust thescreen brightness, contrast,sharpness and offset level.HDMIDVI-DHDMID-SUBHDMIDVI-DHDMID-SUB
14On Screen Display(OSD) Selection and Adjustment NOTE The order of icons may differ depending on the model (13 to 28).LANGUAGE WHITE BALANCEPOWER INDICATORFACTORY RESETUse this menu to set the userpreferences and the pictureoptions.OTHERSDVI-DHDMIDVI-DHDMID-SUBD-SUBD-SUBPIP ON / OFF PIP INPUTPIP POSITIONPIP SWAPPIP SOUNDPIP VOLUMETo adjust PIP functionPIPDVI-DHDMID-SUBHORIZONTALVERTICALCLOCKPHASEOVERSCANDISPLAY To adjust the position of thescreen To improve the clarity andstability of the screen HDMID-SUBD-SUBUse this menu to allow the pictureto completely fill the screen,removing noise around the edgesof HDMI input video signal.HDMI
15G-MODEG-MODE USER MODEUSER MODE1MODE 1MODE 1MODE 12MODE 2MODE 2MODE 23MODE 3MODE 3MODE 3G-MODEG-MODE USER MODEUSER MODENORMALNORMAL MODE 1MODE 1 MODE 2MODE 2 MODE 3MODE 3On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipPress the G-MODE Button, then the main menu of the OSD appears.Move to the upper menuAdjust (Decrease/Increase)Select another sub-menuExit
16On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionG-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3G-MODEG-MODE USER MODEUSER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODEG-MODE USER MODEUSER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMALNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1MODE 1 MODE 2 MODE 3: Move to the upper menu, : MoveEXIT : ExitNORMALMODE 1/MODE 2/MODE 3This menu allows you to easily customize the settings to your preferences, such asBrightness, SUPER+ RESOLUTION, and screen Aspect Ratio. Once set, you can select theoptimized mode depending on your preferences.The following is the default setting.ASPECT RATIO (Full), SUPER+ RESOLUTION (NORMAL),BRIGHTNESS (100)If you select MODE1 in USER MODE and setASPECT RATIO, SUPER+ RESOLUTION,and BRIGHTNESS for your preferences, thesettings are saved in MODE1. You can saveyour preferences in MODE2 and MODE3 inthe same way.If you set the ASPECT RATIO, SUPER+ RESOLUTION, BRIGHTNESS menus for yourpreferences, such as UCC video viewing, gaming and Internet surfing, you can change thesettings for the three menus at once by simply changing the mode.* The settings in MODE1, MODE2 and MODE3 are not changed even after factory reset unless you change them.* You can save the customized settings in the General mode. However, the settings are changed to the factory default after factory reset.* The table shows the settings available for three menus in each user mode.SUPER+ RESOLUTIONNORMALMODE 1MODE 2MODE 3USER MODE ASPECT RATIO BRIGHT-NESS RemarkFULLFULL/ORIGINAL/1:1FULL/ORIGINAL/1:1FULL/ORIGINAL/1:11000 ~ 1000 ~ 1000 ~ 100NORMALNORMAL/LOW/MEDIUM/HIGHNORMAL/LOW/MEDIUM/HIGHNORMAL/LOW/MEDIUM/HIGHBrightness, SUPER+RESOLUTION, andscreen aspect ratio canbe customized for userpreferences.
On Screen Display(OSD) Selection and Adjustment 17Main menu Sub menu DescriptionONNot use the Frame-Buffer memoryto prevent the picture delay. It canuse in GAME MODE to preventpicture delay.The screen blinks when you setTHRU MODE to ON or OFF.G-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3G-MODE USER MODEUSER MODEG-MODEG-MODETHRU MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODEG-MODE THRU MODETHRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3OFF: Move to the upper menu, : MoveEXIT : ExitFrame buffer (video memory) is used.* Frame buffer must be used for PIP, screen aspect ratio, and HDMI video signal input. (THRU MODE OFF)This function cannot be used with THRU MODE ON.
18On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionG-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3G-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODEG-MODE SUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODEG-MODE SUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODEG-MODE SUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3: Move to the upper menu, : MoveEXIT : Exit* Noise may exist according to SR(SUPER+ RESOLUTION) Mode, so enjoy the clear image by selecting SR(SUPER+ RESOLUTION) Mode according to the Contents.Select this when you want to use theproduct in the most general usingenvironment. In the General mode, theSUPER+ RESOLUTION is turned off.When the user wants a natural videoscreen with soft image, it helps to get theoptimized screen. It is effective for videowith small movement or still image.When the user wants a comfortablevideo screen at the medium levelbetween low and high mode, it helps toget the optimized screen. It is effectivefor UCC and SD level videos.When the user wants a sharp videoscreen with clear images, it helps to getthe optimized screen. It is effective forhigh resolution video screens andgames.NORMALLOWMEDIUMHIGH
On Screen Display(OSD) Selection and Adjustment 19Main menu Sub menu DescriptionG-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3G-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEG-MODEASPECT RATIOASPECTASPECT RA RATIOTIOG-MODEG-MODE ASPECTASPECT RA RATIOTIOG-MODEG-MODE ASPECTASPECT RA RATIOTIOORIGINALFULL ORIGINALORIGINAL 1:11:11:11:1FULLFULL1:1ORIGINALORIGINALFULLFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3: Move to the upper menu, : MoveEXIT : ExitThe picture will be displayed withFull size.The picture will be displayed withinput resolution ratio scaling. If 640 x480 resolution input, the picture willkeep at 4:3 ratio scaling.The picture will be displayeddepends on Input resolution.NoScaling. If 640 x 480 resolutioninput, the picture will just display 640 x 480 size even though the 1920 x 1080 size panel.FULLORIGINAL1:1
20On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionONSelect this to adjust the brightnessautomatically. If it is set to ON, thescreen brightness is automaticallyadjusted using the light sensor.Depending on the ambientbrightness or input data, the screenbrightness is adjusted by adjustingthe backlight to provide the optimalplayback experience.G-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3G-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEG-MODEAUTO BRIGHTAUTAUTO BRIGHTO BRIGHTG-MODE AUTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3OFF: Move to the upper menu, : MoveEXIT : ExitAuto brightness adjustment functionis turned OFF.G-MODE USER MODEUSER MODEG-MODETHRU MODETHRU MODEG-MODE USER MODEG-MODE USER MODEMODE 1MODE 1 MODE 2MODE MODE 3MODE G-MODE THRU MODEG-MODESUPER+ RESOLUTIONSUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODE SUPER+ RESOLUTIONG-MODEASPECT RATIOASPECT RATIOG-MODE ASPECT RATIOG-MODE ASPECT RATIOORIGINALFULL ORIGINAL 1:11:1FULL1:1ORIGINALFULLG-MODEAUTO BRIGHTAUTO BRIGHTG-MODEG-MODE AUTAUTO BRIGHTO BRIGHTNORMAL MODE 1 MODE 2 MODE 3NORMAL MODE 1 MODE 2 MODE 3
On Screen Display(OSD) Selection and Adjustment 21The OSD screen will appear when you press the INPUT button on the front ofthe monitor.Main menu Sub menu DescriptionSub-menu NameMenu NameButton TipINPUTOKOKINPUTINPUTOKOKINPUTOKINPUTOKINPUTOKD-SUBD-SUBD-SUBD-SUBD-SUBDVI-DDVI-DDVI-DDVI-DDVI-D: Move to the upper menu, : MoveOK : Select the menuEXIT : ExitD-SUB This inputs video signals in analogformat.Connect a 15-pin D-Sub cable andselect D-SUB.INPUTOKOKINPUTINPUTOKOKINPUTOKINPUTOKINPUTOKD-SUBD-SUBD-SUBD-SUBD-SUBDVI-DDVI-DDVI-DDVI-DDVI-DDVI-D This inputs video signals in digital format.Connect a DVI-D cable and select DVI-D.INPUTOKOKINPUTOKINPUTINPUTOKOKINPUTOKINPUTOKD-SUBD-SUBD-SUBD-SUBD-SUBDVI-DDVI-DDVI-DDVI-DDVI-DHDMI 1 This inputs video and audio signals indigital format.Connect a HDMI cable and select HDMI.INPUTOKOKINPUTOKINPUTOKINPUTINPUTOKOKINPUTOKD-SUBD-SUBD-SUBD-SUBD-SUBDVI-DDVI-DDVI-DDVI-DDVI-DHDMI 2INPUTOKOKINPUTOKINPUTOKINPUTOKINPUTINPUTOKOKD-SUBD-SUBD-SUBD-SUBD-SUBDVI-DDVI-DDVI-DDVI-DDVI-D
22On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipPress the MENU Button, then the main menu of the OSD appears.Move to the upper menuAdjust (Decrease/Increase)Select another sub-menuExit
On Screen Display(OSD) Selection and Adjustment 23Main menu Sub menu DescriptionBRIGHTNESSCONTRAST SHARPNESSBLACK LEVELTo adjust the brightness of thescreen. To adjust the contrast of the screen.To adjust the clearness of the screen.You can set the offset level. If you select'HIGH', the screen will be bright and ifyou select ‘LOW’, the screen will bedark. (This option is enabled only forHDMI signal input in YUV color format.)* Offset?As the criteria for video signal, it is thedarkest screen the monitor can show.PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMEPIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUME: Move to the upper menu: Decrease: Increase: Select another sub-menuEXIT : Exit D-SUB/DVI-D inputHDMI input
24On Screen Display(OSD) Selection and Adjustment PRESETSelect the screen color. • sRGB: Set the screen color to fit thesRGB standard colorspecification.• You can select different color temperatures: 5000K, 6500K, 7200K, 8200K and 9300K. REDGREENBLUEGAMMA Set your own gamma value. : 0 / 1 / 2On the monitor, high gamma valuesdisplay whitish images and lowgamma values display blackishimages.PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMECOLOR TEMPUSERPIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMEMain menu Sub menu DescriptionPRESET ModeUSER ModeSelect either PRESET or USER toadjust the screen color. : Move to the upper menu: Decrease: Increase: Select another sub-menuEXIT : Exit D-SUB/DVI-D inputHDMI inputHUESATURATIONCOLOR RESETSet your own hue levels.(only for HDMI input)Set your own saturation levels.(only for HDMI input)Use this menu to reset the color tofactory settings.* This option is enabled only for HDMI signal input in YUV color format.The higher the colortemperature gets, thebluer the screenbecomes; the lowerthe color temperaturegets, the bluer thescreen becomes.
25On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionPIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMEPIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMETo move image left and right.To move image up and down.To minimize any vertical bars or stripesvisible on the screen background.The horizontal screen size will alsochange.To adjust the focus of the display. This item allows you to remove anyhorizontal noise and clear or sharpenthe image of characters.Removes noise that may occur at theedges of an image when HDMI isconnected to an external device. WhenON is selected, the image size isreduced to prevent noise. When OFF isselected, the original image size ismaintained regardless of noise. (Only for HDMI input)HORIZONTALVERTICALCLOCKPHASEOVERSCAN: Move to the upper menu: Decrease: Increase: Select another sub-menuEXIT : Exit D-SUB inputHDMI input
26On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionPIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMEPIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUME: Move to the upper menu: Decrease: Increase: Select another sub-menuEXIT : Exit Press the , buttons to resetimmediately.To choose the language in which thecontrol names are displayed.LANGUAGEWHITEBALANCEIf the output of the video card isdifferent the required specifications,the color level may deteriorate dueto video signal distortion. Using thisfunction, the signal level is adjustedto fit into the standard output level ofthe video card in order to provide theoptimal image.Activate this function when whiteand black colors are present in thescreen.Restore all factory default settings except"LANGUAGE." FACTORYRESETPOWERINDICATORUse this menu to set the powerindicator (on the bottom right of themonitor) to ON or OFF.If you set OFF, it will go off. If you set ON at any time, the powerindicator will automatically be turned on.NOTE If this does not improve the screen image, restore the factory default settings. If necessary, execute theWHITE BALANCE function again. This function will be enabled only when the input signal is an analogsignal. D-SUB inputHDMI/DVI-D input
27On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionPIPPIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMENO30PIP ON / OFFPIP INPUTPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMEPIPPIP ON / OFFPIP INPUTPIP INPUTPIP POSITIONPIP POSITIONPIP SWAPPIP SOUND PIP VOLUMEDVI-DNO30PIPPIP ON / OFFPIP INPUTPIP INPUTPIP POSITIONPIP POSITIONPIP SWAPPIP SWAPPIP SOUND PIP SOUND PIP VOLUMEPIP VOLUMEDVI-DNO30: Move to the upper menu: Decrease: Increase: Select another sub-menuEXIT : Exit Select PIP input.PIP ON/OFFPIP INPUTPIP POSITIONTo select PIP on or off.* It supports only for HDMI input in RGB(D-sub analog signal)mode.* The combinations of main screen andsub-screen (PIP) available are as shownbelow: PIP SOUND Use this menu to turn the PIP Soundon or off. (Only for HDMI input)PIP SWAP Use this menu to switch between themain menu and the sub menu.PIP VOLUME Use this menu to adjust the volume ofthe PIP Sound. (Only for HDMI input)Select the PIP display location. Everytime you touch the button, it will movefrom to , , . Every time youpress the button, it will move fromto , , . You can use this menu toselect the PIP display location you want.: Top left: Bottom left: Bottom right: Top rightSelect the PIP display location. Everytime you touch the button, it will movefrom to , , . Every time youpress the button, it will move fromto , , . You can use this menu toselect the PIP display location you want.: Top left: Bottom left: Bottom right: Top right*It operates only when PIP is on.2143123414 3 2D-SUB/DVI-D inputHDMI inputD-SUB DVI HDMI 1 HDMI 2- O O OO - O OO O - XO O X -Main screen Sub-screen (PIP) D-SUBDVIHDMI 1HDMI 2
28On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the VOLUME button on thefront of the monitor.Main menu Sub menu DescriptionSub-menu NameMenu NameButton TipVOLUME To adjust the volume of headphone/Earphone.(Only for HDMI input)HDMI input: Move to the upper menu: Decrease: Increase: MuteEXIT : Exit
29TroubleshootingNo image appearsCheck the following before calling for service.No image appearsDo you see a "OSD LOCKED" message on the screen?●Is the power cord of thedisplay connected?●Is the power indicatorlight on?●Is the power indicatorblinking?●Do you see an "OUT OFRANGE" message onthe screen?●Do you see a "CHECKSIGNAL CABLE"message on thescreen?• Check and see if the power cord is connectedproperly to the power outlet.• Press the Power button.• If the display is in power saving mode, try movingthe mouse or pressing any key on the keyboard tobring up the screen.• Try to turn on the PC.• This message appears when the signal from thePC (video card) is out of horizontal or verticalfrequency range of the display. See the'Specifications' section of this manual andconfigure your display again.• This message appears when the signal cablebetween your PC and your display is notconnected. Check the signal cable and try again.• You can secure the current control settings,so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby pushing the MENU button for severalseconds: the message “OSD UNLOCKED” will appear.●Do you see “OSDLOCKED” when youpush MENU button?
30TroubleshootingDisplay image is incorrect●Display Position isincorrect.●On the screenbackground, verticalbars or stripes arevisible.●Any horizontal noiseappearing in anyimage or charactersare not clearlyportrayed.• Press the AUTO button to automatically adjustyour display image to the ideal setting. • Press the AUTO button to automatically adjustyour display image to the ideal setting.• Press the AUTO button to automatically adjustyour display image to the ideal setting.• Check Control Panel --> Display --> Settingsand adjust the display to the recommendedresolution or adjust the display image to the idealsetting. Set the color setting higher than 24 bits(true color).IMPORTANTCheck Control Panel --> Display --> Settings and see if the frequency or the resolutionwere changed. If yes, readjust the video card to the recommend resolution.If the recommended resolution (optimal resolution) is not selected, letters may be blurredand the screen may be dimmed, truncated or biased. Make sure to select the recommendresolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer.
31TroubleshootingThe Audio function is not workingDisplay image is incorrect●The screen color ismono or abnormal.●The screen blinks.• Check if the signal cable is properly connectedand use a screwdriver to fasten if necessary.• Make sure the video card is properly inserted inthe slot.• Set the color setting higher than 24 bits (true color)at Control Panel - Settings.• Check if the screen is set to interlace mode and ifyes, change it to the recommend resolution.●Picture OK & No sound.• Check whether volume is "0".• Check sound muted.• HDMI cable installed properly.• Head phone cable installed properly.• Check sound format. Not supply to compressedsound format.Do you see an "Unrecognized monitor, Plug&Play (VESADDC) monitor found" message?●Have you installed thedisplay driver?• Be sure to install the display driver from the displaydriver CD (or diskette) that comes with yourdisplay. Or, you can also download the driver fromour web site: http://www.lg.com.• Make sure to check if the video card supportsPlug&Play function.
32Specifications E2370V58.42 cm (23 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 58.42cm0.265 mm x 0.265 mm (Pixel pitch)DisplaySync InputVideo InputMax VESA 1920 x 1080 @ 60 HzRecommend VESA 1920 x 1080 @ 60 HzResolutionPlug&PlayOn Mode :39 W (Typ.)Sleep Mode ≤1 W Off Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsTilt : -5˚ to 15˚RangeAC 100-240 V~ 50 / 60 Hz 0.7 APower InputAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B (Analog, Digital, HDMI)NOTEInformation in this document is subject to change without notice.Horizontal Freq. Analog,Digital: 30 kHz to 83 kHz HDMI : 30 kHz to 83 kHz Vertical Freq. Analog,Digital : 56 Hz to 75 Hz HDMI : 56 Hz to 61 Hz Input Form Separate Sync., DigitalSignal Input 15 pin D-Sub ConnectorDVI-D connector (Digital)19 pin HDMI ConnectorInput Form Analog (0.7 Vp-p/ 75 ohm), Digital, HDMIWith StandWidth 55.62 cm (21.90 inch) Height 41.27 cm (16.25 inch) Depth 17.78 cm (7 inch)Weight(excl. packing) 4.4 kg (9.70 lb)Dimensions& WeightWithout StandWidth 55.62 cm (21.90 inch) Height 34.51 cm (13.59 inch)Depth 6.04 cm (2.38 inch)
Specifications E2770V3368.6 cm (27 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 68.6cm0.311 mm x 0.311 mm (Pixel pitch)DisplaySync InputVideo InputMax VESA 1920 x 1080 @ 60 HzRecommend VESA 1920 x 1080 @ 60 HzResolutionPlug&PlayOn Mode :41 W (Typ.)Sleep Mode ≤1 W Off Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsTilt : -5˚ to 15˚RangeAC 100-240 V~ 50 / 60 Hz 0.7 APower InputAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B (Analog, Digital, HDMI)NOTEInformation in this document is subject to change without notice.Horizontal Freq. Analog,Digital: 30 kHz to 83 kHz HDMI : 30 kHz to 83 kHz Vertical Freq. Analog,Digital : 56 Hz to 75 Hz HDMI : 56 Hz to 61 Hz Input Form Separate Sync., DigitalSignal Input 15 pin D-Sub ConnectorDVI-D connector (Digital)19 pin HDMI ConnectorInput Form Analog (0.7 Vp-p/ 75 ohm), Digital, HDMIWith StandWidth 65.46 cm (25.77 inch) Height 48.85 cm (19.23 inch) Depth 23.08 cm (9.09 inch)Weight(excl. packing) 5.6 kg (12.35 lb)Dimensions& WeightWithout StandWidth 65.46 cm (25.77 inch) Height 40.45 cm (15.93 inch)Depth 6.04 cm (2.38 inch)
34SpecificationsIndicatorOn ModeSleep ModeOff ModeRedRed BlinkingOffLED ColorMODEPreset Modes (Resolution)Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)12345678910111213*14640 x 350720 x 400640 x 480640 x 480800 x 600800 x 6001024 x 7681024 x 7681152 x 8641280 x 10241280 x 10241680 x 10501680 x 10501920 x 108031.46931.46831.46937.50037.87946.87548.36360.12367.50063.98179.97664.67465.29067.5007070607560756075756075606060*Recommend ModeDSUB/DVI TimingDisplay Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)12345678480P576P720P720P1080i1080i1080P1080P31.5031.2537.5045.0028.1233.7556.2567.506050506050605060HDMI Timing
35Installing the Wall mount plateThis monitor satisfies the specifications of the Wall mount plate or theinterchange device.1.Place the monitor face down on the cushion or soft cloth.3.Check the direction of the Stand Base and pull it from the Stand Body in the direction shown in the figure below. 2.To remove the Stand Base from the Stand Body, turn the screw counterclockwise using a coin. Stand BaseStand Body4.Loosen the screws on the back of the monitor to remove the Stand Body from the monitor. (E2370V)(E2770V)
36Installing the Wall mount plate4.Install the Wall mount plate.Wall mount plate(Separate purchase)This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for more details,which is provided when Wall mount plate ispurchased. Kensington Security SlotConnected to a locking cable thatcan be purchased separately atmost computer stores.<Screw Mounting Interface Dimension>Hole spacing : 100 mm x 100 mm. (E2370V)200 mm x 100 mm. (E2770V)Wall Mount pad
As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).Make sure to read the Important Precautions before using the product.Keep the Owner’s Manual(CD) in an accessible place for future reference.The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.MODELSERIAL
Regulatory Information cont. FCC Compliance StatementThis equipment has been tested and found to complywithin the limits of a Class B digital device pursuant to Part15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation.This equipment generates, uses, and can radiate radiofrequency energy and if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there isno guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radioor television reception (which can be determined byturning the equipment on and off), the user is encouragedto try to correct the interference by using one or more ofthe following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and the receiver.Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult the dealer or an experienced radio/TVtechnician for help.Caution: Changes or modifications not expressly approvedby the party responsible for compliance could void theuser's (or your) authority to operate the equipment. Onlyperipherals (digital input/output devices, terminals, printers,etc.) certified to comply with the Class B limits may beattached to this monitor. Operation with non-certifiedperipherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used withthis System.Canadian DOC NoticeThis Class B digital apparatus meets all requirements ofthe Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe Brespecte toutes les exigences du Règlement sur lematériel brouilleur du Canada.CE Conformity Notice (for Europe)Products with the “CE” Marking comply with the EMCDirective(89/336/EEC) and LOW VOLTAGE Directive(73/23/EEC) issued by the Commission of the EuropeanCommunity.Compiance with these directives implies conformity to thefollowing European Norms :• EN 55022 ; Radio Frequency Interference• EN 55024 ; Electromagnetic Immunity• EN 61000-3-2 ; Power Line Harmonics• EN 61000-3-3 ; Voltage Fluctuations• EN 60950-1 ; Product SafetyLow Radiation Compliance (MPR II)This monitor meets one of the strictest guidelines availabletoday for low radiation emissions, offering the user extrashielding and an antistatic screen coating. Theseguidelines, set forth by a government agency in Sweden,limit the amount of emission allowed in the Extremely LowFrequency (ELF) and Very Low Frequency (VLF)electromagnetic range.01NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.TCO'99 (TCO'99 applied model only)Congratulations!You have just purchased a TCO’99 approved and labelledproduct! Your choice has provided you with a productdeveloped for professional use. Your purchase has alsocontributed to reducing the burden on the environment andalso to the further development of environmentallyadapted electronics products.
Regulatory Information cont. 02Why do we have environmentally labelled computers?In many countries, environmental labelling has become anestablished method for encouraging the adaptation ofgoods and services to the environment. With the growingmanufacture and usage of electronic equipmentthroughout the world, there is a recognized concern for thematerials and substances used by electronic productswith regards to their eventual recycling and disposal. Byproper selection of these materials and substances, theimpact on the environment can be minimized.There are also other characteristics of a computer, such asenergy consumption levels, that are important from theviewpoints of both the work (internal) and natural (external)environments. Electronic equipment in offices is often leftrunning continuously, resulting in unnecessaryconsumption of large amounts of energy and additionalpower generation. From the standpoint of carbon dioxideemissions alone, it is vital to save energy.What does labelling involve?The product meets the requirements for the TCO’99scheme which provides for international and environmentallabelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of ProfessionalEmployees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) andStatens Energimyndighet (The Swedish NationalEnergy Administration).Approval requirements cover a wide range of issues:ecology, ergonomics, emission of electrical and magneticalfields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence anduse of heavy metals, brominated and chlorinated flameretardants, and other substances. The product must beprepared for recycling and the manufacturing site(s) shallbe certified according to ISO14001 or EMAS registered.Energy requirements include a demand that the systemunit and/or display, after a certain period of inactivity,shall reduce its power consumption to a lower level in oneor more stages. The length of time to reactivate the systemunit shall be reasonable for the user.Labelled products must meet strict environmentaldemands, for example, in respect of the reduction ofelectrical and magnetical fields as well as work load andvisual ergonomics.Below you will find a brief summary of the ecologicalrequirements met by this product. The completeecological criteria document can be found at TCODevelopment’s website http://www.tcodevelopment.comor may be ordered from:TCO DevelopmentSE-114 94 STOCKHOLM, SwedenFax: +46 8 782 92 07Email : development@tco.seInformation regarding TCO’99 approved and labelledproducts may also be obtained athttp://www.tcodevelopment.comEcological requirementsFlame retardantsFlame retardants may be present in printed wiring boardlaminates, cables, and housings. Their purpose is toprevent, or at least to delay the spread of fire. Up to 30%by weight of the plastic in a computer casing can consist offlame retardant substances. Many flame retardantscontain bromine or chlorine, and these flame retardantsare chemically related to PCBs (polychlorinatedbiphenyls). Both the flame retardants containing bromineor chlorine and the PCBs are suspected of giving rise tohealth effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*processes when not disposed of in accordance with strictstandards for disposal.TCO’99 requires that plastic components weighing morethan 25 grams shall not contain flame retardants withorganically bound bromine or chlorine. Flame retardantsare allowed in the printed wiring board laminates due tothe lack of commercially available alternatives.Cadmium**Cadmium is present in rechargeable batteries and in thecolour-generating layers of certain computer displays.TCO’99 requires that batteries, the colour-generatinglayers of display screens, and the electrical or electronicscomponents shall not contain any cadmium.Mercury**Mercury is sometimes found in batteries, relays andswitches. TCO’99 requires that batteries shall not containany mercury. It also demands that mercury is not presentin any of the electrical or electronics componentsassociated with the labelled unit. There is however one
Regulatory Information cont. 03exception. Mercury is, for the time being, permitted in theback light system of flat panel monitors as there today isno commercially available alternative. TCO aims onremoving this exception when a mercury free alternative isavailable.Lead**Lead can be found in picture tubes, display screens,solders and capacitors. TCO’99 permits the use of leaddue to the lack of commercially available alternatives, butin future requirements TCO Development aims atrestricting the use of lead._____________________________________________* Bio-accumulative is defined as substances which accumulate in living organisms.**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.TCO’03(TCO’03 applied model only)Congratulations!The display you have just purchased carries the TCO’03Displays label. This means that your display is designed,manufacturedand tested according to some of the strictest quality andenvironmental requirements in the world. This makes for ahigh performance product, designed with the user in focusthat also minimizes the impact on our natural environment.Some of the features of the TCO’03 Display requirements:Ergonomics• Good visual ergonomics and image quality in order toimprove the working environment for the user and toreduce sight and strain problems. Importantparameters are luminance, contrast, resolution,reflectance, colour rendition and image stability.Energy• Energy-saving mode after a certain time – beneficialboth for the user and the environment• Electrical safetyEmissions• Electromagnetic fields• Noise emissionsEcology• The product must be prepared for recycling and themanufacturer must have a certified environmentalmanagement system such as EMAS or ISO 14 001• Restrictions onchlorinated and brominated flame retardants andpolymersheavy metals such as cadmium, mercury and lead.The requirements included in this label have beendeveloped by TCO Development in co-operation withscientists, experts, users as well as manufacturers all overthe world. Since the end of the 1980s TCO has beeninvolved in influencing the development of IT equipment ina more user-friendly direction. Our labelling system startedwith displays in 1992 and is now requested by users andIT-manufacturers all over the world.For more information, please visitwww.tcodevelopment.comInformation for Environmental PreservationLGE. announced the 'LG Declaration for a CleanerEnvironment' in 1994, and this ideal has served as aguiding managerial principle ever since. The Declaration isa foundation that has allowed us to undertakeenvironmentally friendly activities in careful considerationof economic, environmental, and social aspects.We promote activities for environmental preservation, andwe specifically develop our products to embrace theconcept of environment-friendly. We minimize the hazardous materials contained in ourproducts. For example, there is no cadmium to be found inour monitors.Information for recyclingThis monitor may contain parts which could be hazardousto the environment. It is important that this monitor berecycled after use.LGE. handles all waste monitors through anenvironmentally acceptable recycling method. There areseveral take-back and recycling systems currently inEnglish
Regulatory Information cont. 04operation worldwide. Many parts will be reused andrecycled, while harmful substances and heavy metals aretreated by an environmentally friendly method.If you want to find out more information about ourrecycling program, please contact your local LG vendor ora corporate representative of LG. We set our vision and policies on a cleaner world byselecting the issue of the global environment as a task forcorporate improvement. Please visit our website for moreinformation about our ‘green’ policies.http://www.lge.com/about/environment/html/Recycling.jspInformationen zur Erhaltung der UmweltIm Jahr 1994 verkündete LGE die 'LG Declaration for aCleaner Environment' (LG Erklärung für eine sauberereUmwelt). Seitdem dient dieses Ideal als führendes Prinzipdes Unternehmens. Diese Erklärung war die Basis für dieDurchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche,umweltbezogene und soziale Aspekte in die Überlegungen mit einbezogen wurden.Wir fördern Aktivitäten zum Schutz der Umwelt und dieEntwicklung unserer Produkte ist darauf ausgerichtet,unserem Konzept bezüglich Umweltfreundlichkeit gerechtzu werden. Wir sind darauf bedacht, den Anteil der in unserenProdukten enthaltenen schädlichen Materialien zuminimieren. So ist in unseren Monitoren beispielsweisekein Kadmium zu finden.Informationen zum Thema RecyclingDieser Monitor enthält Teile, die umweltschädlich seinkönnen. Es ist unbedingt erforderlich, dass der Monitorrecycelt wird, nachdem er außer Dienst gestellt wurde.Bei LGE. werden alle ausrangierten Monitore in einemunter umweltbezogenen Aspekten geeigneten Verfahrenrecycelt. Augenblicklich sind weltweit mehrereRücknahme- und Recyclingsysteme im Einsatz. VieleTeile werden wieder verwendet und recycelt. SchädlicheSubstanzen und Schwermetalle werden durchumweltverträgliche Verfahren behandelt.Falls Sie mehr über unser Recyclingprogramm erfahrenmöchten, wenden Sie sich bitte an Ihren lokalen LG-Händler oder einen Unternehmensvertreter von LG. Wir richten unsere Firmenpolitik auf eine sauberereUmwelt hin aus, indem wir umweltspezifische Aspekte alswichtigen Punkt in die Weiterentwicklung unseresUnternehmens einfließen lassen. ZusätzlicheInformationen über unsere ‘grüne’ Firmenpolitik erhaltenSie auf unserer Website.http://www.lge.com/about/environment/html/Recycling.jspInformation sur la protection del’environnementLGE. a publié sa 'Déclaration en faveur d’unenvironnement plus propre' en 1994 et celle-ci est restée,depuis lors, un principe directeur de notre entreprise.Cette déclaration a servi de base à notre réflexion et nousa permis de prendre en compte à la fois les aspectséconomiques et sociaux de nos activités, tout enrespectant l’environnement.Nous encourageons les activités en faveur de lapréservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons auminimum les matières dangereuses qui entrent dans leurcomposition et l’on ne trouve pas de cadmium, parexemple, dans nos moniteurs.Information sur le recyclageCe moniteur peut contenir des composants qui présententun risque pour l’environnement. Il est donc important quecelui-ci soit recyclé après usage.LGE. traite les moniteurs en fin de cycle conformément àune méthode de recyclage respectueuse del’environnement. Nous reprenons nos produits et lesrecyclons dans plusieurs sites répartis dans le mondeentier. De nombreux composants sont réutilisés etrecyclés, et les matières dangereuses, ainsi que lesmétaux lourds, sont traités selon un procédé écologique.Si vous souhaitez plus de renseignements sur notreprogramme de recyclage, veuillez contacter votrerevendeur LG ou un l’un de nos représentants. Nous voulons agir pour un monde plus propre et croyonsau rôle de notre entreprise dans l’amélioration del’environnement. Pour plus de renseignements sur notrepolitique “verte”, rendez visite à notre site :http://www.lge.com/about/environment/html/Recycling.jspDeutschFrançais
05Regulatory Information cont. Informazioni per la tutela dell’ambienteLa LGE. ha annunciato nel 1994 la cosiddetta 'LGDeclaration for a Cleaner Environment' (Dichiarazione diLG a favore di un ambiente più pulito), un ideale che daallora funge da principio ispiratore della gestioneaziendale. La dichiarazione rappresenta il fondamento checonsente di intraprendere attività a favore dell'ambientetenendo conto degli aspetti economici, ambientali esociali.Noi della LG, promuoviamo attività a favore dellatutela dell'ambiente sviluppando appositamente i nostriprodotti per cogliere il concetto del rispetto dell’ambienteriducendo i materiali dannosi presenti nei nostri prodotti.Ad esempio nei nostri monitor non è presente il cadmio.Informazioni per il riciclaggioIl monitor può presentare componenti che potrebberorisultare eventualmente dannosi per l'ambiente. Èimportante che il monitor sia riciclato al termine del suoutilizzo.La LGE. gestisce tutti i monitor di rifiuto con un metodo diriciclaggio soddisfacente dal punto di vista ambientale. Intutto il mondo sono attualmente in funzione numerosisistemi di riciclaggio e recupero. I diversi componenti sonoriutilizzati e riciclati, mentre le sostanze dannose e i metallipesanti vengono trattati con un metodo rispettosodell’ambiente.Se si desiderano maggiori informazioni in merito alprogramma di riciclaggio, è consigliabile rivolgersi alproprio rivenditore LG o ad un rappresentante aziendaledella LG. Noi della LG impostiamo la nostra visione e le nostrepolitiche a favore di un mondo più pulito ponendo laquestione dell'ambiente dal punto di vista globale comeuna mansione rivolta al miglioramento della nostraazienda. Vi invitiamo a visitare il nostro sito internet perulteriori informazioni sulla nostra politica “verde”.http://www.lge.com/about/environment/html/Recycling.jspInformación para la conservación medioambientalLGE. presentó la 'Declaración para un entorno más limpiode LG' en 1994 y este ideal ha servido para guiar nuestrosprincipios empresariales desde entonces. La Declaraciónes la base que nos ha permitido llevar a cabo tareas querespetan el medio ambiente siempre teniendo en cuentaaspectos sociales, económicos y medioambientales.Promocionamos actividades orientadas a la conservacióndel medio ambiente y desarrollamos nuestros productosespecíficamente para que se ajusten a la filosofía queprotege el entorno. Reducimos al máximo el uso de materiales de riesgo ennuestros productos. Un ejemplo de ello es la ausenciatotal de cadmio en nuestros monitores.Información para el reciclajeEste monitor puede contener piezas que entrañen riesgosmedioambientales. Es importante reciclar este monitordespués de su utilización.LGE. trata todos los monitores usados siguiendo unmétodo de reciclaje que no daña al entorno. Contamoscon diversos sistemas de recuperación y reciclaje quefuncionan a nivel mundial en la actualidad. Es posiblereciclar y reutilizar muchas de las piezas, mientras que lassustancias dañinas y los metales pesados se tratansiguiendo un método que no perjudique al medioambiente. Si desea obtener más información acerca delprograma de reciclaje, póngase en contacto con suproveedor local de LG o con un representante empresarialde nuestra marca. Basamos nuestra visión y nuestras políticas en un mundomás limpio y para ellos optamos por un entorno globalcomo tarea principal de nuestra evolución como empresa.Visite nuestra página Web para obtener más informaciónsobre nuestras políticas ecológicas.http://www.lge.com/about/environment/html/Recycling.jspInformações relacionadas à preservaçãoambientalA LGE. anunciou a 'LG Declaration for a CleanerEnvironment' (Declaração da LG para um ambiente maislimpo) em 1994 e esse ideal tem servido desde entãocomo um princípio administrativo de orientação. ADeclaração é a base que nos tem permitido realizaratividades favoráveis ao ambiente com consideraçãoatenta aos aspectos econômicos, ambientais e sociais.Promovemos atividades de preservação ambiental edesenvolvemos nossos produtos para englobarItalianoEspanõlPortuguês
06Regulatory Information cont. especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossosprodutos. Por exemplo, não há cádmio em nossosmonitores.Informações relacionadas à reciclagemEste monitor pode conter peças que podem representarriscos ao ambiente. É importante que ele seja recicladoapós o uso.A LGE. cuida de todos os monitores descartados atravésde um método de reciclagem agradável ao ambiente. Hávários sistemas de devolução e reciclagem atualmenteem operação no mundo. Muitas peças serão reutilizadase recicladas e as substâncias nocivas e os metaispesados passarão por tratamento através de um métodofavorável ao ambiente.Para obter mais informações sobre nosso programa dereciclagem, entre em contato com seu fornecedor LGlocal ou com um representante corporativo da LG. Definimos nossa visão e nossas políticas relacionadas aum mundo mais limpo selecionando a questão doambiente global como uma tarefa de aprimoramentocorporativo. Visite nosso site para obter mais informaçõessobre nossas políticas de meio ambiente.http://www.lge.com/about/environment/html/Recycling.jspInformatie met betrekking tot het behoud vanhet milieuLGE. publiceerde in 1994 de 'LG Declaration for a CleanerEnvironment' (de LG-verklaring met betrekking tot eenschoner milieu). Deze verklaring en het ideaal van eenschoner milieu fungeren sindsdien als een bestuurlijkeleidraad voor onze onderneming. Op basis van dezeverklaring ontplooien wij milieuvriendelijke activiteiten,waarbij er zowel met sociale en economische aspecten,als met milieuaspecten zorgvuldig rekening wordtgehouden.Wij ondersteunen activiteiten die zijn gericht op hetbehoud van het milieu en wij houden bij het ontwikkelenonze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen inonze producten. Er wordt bijvoorbeeld geen cadmiumverwerkt in onze monitors.NederlandsInformatie met betrekking tot recyclingDeze monitor bevat materialen die schadelijk zoudenkunnen zijn voor het milieu. Het is belangrijk dat dezemonitor aan het einde van zijn levensduur wordtgerecycled.LGE. verwerkt alle afvalmonitors via een milieuvriendelijkerecyclingmethode. Hiervoor worden er momenteelwereldwijd verscheidene inname- en recyclingsystemengehanteerd. Een groot aantal onderdelen wordt opnieuwgebruikt en gerecycled, waarbij schadelijke stoffen enzware metalen volgens een milieuvriendelijke methodeworden verwerkt.Voor meer informatie over ons recyclingprogramma kunt ucontact opnemen met uw plaatselijke LG-vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonerewereld vloeien voort uit het feit dat wij het milieu hebbenaangemerkt als een onderwerp dat speciale aandachtverdient binnen onze onderneming. Bezoek onze websitevoor meer informatie over ons 'groene' beleid.http://www.lge.com/about/environment/html/Recycling.jsp»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡'ƒÂÍ·‡ˆË˛ LG ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚',ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔË̈ËÔÓÏÛÔ‡‚ÎÂÌˡ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍ·‡ˆËË Ï˚ ÒÏÓ„ÎËÔ‰ÔËÌˇÚ¸ ‰ÂÈÒڂˡ, Ó·ÂÒÔ˜˂‡˛˘Ë ·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÔË ˝ÚÓωÓÎÊÌÓ ‚ÌËχÌË ˝ÍÓÌÓÏ˘ÂÒÍËÏ, ˝ÍÓÎӄ˘ÂÒÍËÏ ËÒӈˇθÌ˚Ï ‡ÒÔÂÍÚ‡Ï.Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂθÌÓÒÚ¸ ÔÓ Óı‡ÌÂÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÓÒÓ·Ó ‚ÌËχÌËÂ‡Á‡·ÓÚÍ ̇¯ÂÈ ÔÓ‰Û͈ËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË ÒÍÓ̈ÂÔˆËÂÈ ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË. Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂʇÌË ÓÔ‡ÒÌ˚ı‚¢ÂÒÚ‚ ‚ ̇¯ÂÈ ÔÓ‰Û͈ËË. Õ‡ÔËÏÂ, ‚ ̇¯ËıÏÓÌËÚÓ‡ı ‚˚ Ì ̇ȉÂÚ ͇‰Ïˡ.»ÌÙÓχˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰Âʇڸ ÍÓÏÔÓÌÂÌÚ˚,ÍÓÚÓ˚ ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛʇ˛˘ÂÈ Ò‰Â.Russian
07Regulatory Information cont. EPA(EPA applied model only)ENERGY STARis a set of power-saving guidelinesissued by the U.S. Environmental ProtectionAgency(EPA).NOM MARK (Mexico only)ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒÎÂËÒÔÓθÁÓ‚‡Ìˡ.KÓÔÓ‡ˆËˇ LGE ÔÂÂ‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚ÂÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„ÓÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍËÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.«‡ ·ÓΠÔÓ‰Ó·ÌÓÈ ËÌÙÓχˆËÂÈ ÔÓ Ì‡¯ÂÈÔÓ„‡ÏÏ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ ÍÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË Ô‰ÒÚ‡‚ËÚÂβ ÍÓÔÓ‡ˆËË LG. Ã˚ ÓËÂÌÚËÛÂÏÒˇ ̇ Ó·ÂÒÔ˜ÂÌË ˝ÍÓÎӄ˘ÂÒÍÓÈ·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ Ò· ˆÂθ˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛÓÍÛʇ˛˘ÂÈ Ò‰˚. ƒÓÔÓÎÌËÚÂθÌÛ˛ ËÌÙÓχˆË˛Ó ̇¯ÂÈ ÔÓÎËÚËÍ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ ‚˚ÏÓÊÂÚ ̇ÈÚË Ì‡ ̇¯ÂÏ Ò‡ÈÚÂ:http://www.lge.com/about/environment/html/Recycling.jspAs an ENERGY STAR Partner LGE U. S.A.,Inc. has determined that this productmeets the ENERGY STAR guidelines forenergy efficiency.
08Regulatory Information cont. 1.When this crossed-out wheeled bin symbol is attachedto a product it means the product is covered by theEuropean Directive 2002/96/EC. 2.All electrical and electronic products should bedisposed of separately from the municipal wastestream via designated collection facilities appointed bythe government or the local authorities. 3.The correct disposal of your old appliance will helpprevent potential negative consequences for theenvironment and human health.4.For more detailed information about disposal of yourold appliance, please contact your city office, wastedisposal service or the shop where you purchased theproduct.Disposal of your old appliance1.Quando su un prodotto è riportato il simbolo di1.När den här symbolen med en överkryssadsoptunna på hjul sitter på en produkt innebär detatt den regleras av European Directive2002/96/EC.2.Alla elektriska och elektroniska produkter börkasseras via andra vägar än de som finns förhushållsavfall, helst via för ändamålet avseddauppsamlingsanläggningar som myndigheternautser.3.Om du kasserar din gamla apparat på rätt sättså bidrar du till att förhindra negativakonsekvenser för miljön och människors hälsa.4.Mer detaljerad information om kassering av dingamla apparat kan får av kommunen,renhållningsverket eller den butik där du köpteprodukten.1.Als het symbool met de doorgekruiste verrijdbareafvalbak op een product staat, betekent dit dathet product valt onder de Europese Richtlijn2002/96/EC.2.Elektrische en elektronische producten mogenniet worden meegegeven met het huishoudelijkafval, maar moeten worden ingeleverd bijspeciale inzamelingspunten die door de lokale oflandelijke overheid zijn aangewezen.3.De correcte verwijdering van uw oude toestelhelpt negatieve gevolgen voor het milieu en demenselijke gezondheid voorkomen.Smaltimento delle apparecchiature obsoleteKassering av din gamla apparatUw oude toestel wegdoen1.Ce symbole, représentant une poubelle surroulettes barrée d'une croix, signifie que leproduit est couvert par la directive européenne2002/96/EC.2.Les éléments électriques et électroniquesdoivent être jetés séparément, dans les vide-ordures prévus à cet effet par votre municipalité. 3.Une élimination conforme aux instructions aideraà réduire les conséquences négatives et risqueséventuels pour l'environnement et la santéhumaine.4.Pour plus d'information concernant l'éliminationde votre ancien appareil, veuillez contacter votremairie, le service des ordures ménagères ouencore la magasin où vous avez acheté ceproduit.Élimination de votre ancien appareilun bidone della spazzatura barrato da una crocesignifica che il prodotto è coperto dalla direttivaeuropea 2002/96/EC.2.Tutti i prodotti elettrici ed elettronici dovrebberoessere smaltiti separatamente rispetto allaraccolta differenziata municipale, medianteimpianti di raccolta specifici designati dalgoverno o dalle autorità locali.3.Il corretto smaltimento delle apparecchiatureobsolete contribuisce a prevenire possibiliconseguenze negative sulla salute umana esull'ambiente.4.Per informazioni più dettagliate sullo smaltimentodelle apparecchiature obsolete, contattare ilcomune, il servizio di smaltimento rifiuti o ilnegozio in cui è stato acquistato il prodotto. EnglishFrenchItalianSwedishDutchWEEE (for Europe )
Regulatory Information cont. 091.Wenn dieses Symbol eines durchgestrichenenAbfalleimers auf einem Produkt angebracht ist,unterliegt dieses Produkt der europäischenRichtlinie 2002/96/EC.2.Alle Elektro- und Elektronik-Altgeräte müssengetrennt vom Hausmüll über dafür staatlichvorgesehenen Stellen entsorgt werden.3.Mit der ordnungsgemäßen Entsorgung des altenGeräts vermeiden Sie Umweltschäden und eineGefährdung der persönlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des altenGeräts erhalten Sie bei der Stadtverwaltung,beim Entsorgungsamt oder in dem Geschäft, woSie das Produkt erworben haben. 1.ŸÙ·Ó ¤Ó· ÚÔ˚fiÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓfi˜‰È·ÁÚ·Ì̤ÓÔ˘ οϷıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙfiÙ ÙÔ ÚÔ˚fiÓηχÙÂÙ·È ·fi ÙËÓ E˘Úˆ·˚΋ O‰ËÁ›· 2002/96/EOK.2.H ·fiÚÚÈ„Ë fiÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓÚÔ˚fiÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿ ·fi Ù· ÁÂÓÈοÔÈÎȷο ·ÔÚÚ›ÌÌ·Ù· ̤ۈ ηıÔÚÈṲ̂ӈÓÂÁηٷÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ Ôԛ˜¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËı› ›Ù ·fi ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·fi ÙȘÙÔÈΤ˜ ·Ú¯¤˜.3.H ÛˆÛÙ‹ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ ı·‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘Á›· ÙÔ˘ ·ÓıÚÒÔ˘.4.°È· ÈÔ ÏÂÙÔÌÂÚ›˜ ÏËÚÔÊÔڛ˜ Û¯ÂÙÈο Ì ÙËÓ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙ ÌÂÙÔ ·ÚÌfi‰›Ô ÙÔÈÎfi ÁÚ·Ê›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛ˘ ÔÈÎÈ·ÎÒÓ·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·fi ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·Ù ÙÔÚÔ˚fiÓ.1.Tämä merkki tuotteessa tarkoittaa, että tuotekuuluu sähkö- ja elektroniikkalaiteromustaannetun EU-direktiivin 2002/96/EYsoveltamisalaan.2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseenkeräyspisteeseen.3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia.4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin,kierrätyskeskukseen tai myymälään, josta ostit laitteen.1.Når der er et tegn med et kryds over enskraldespand, betyder det, at produktet eromfattet af EU-direktiv 2002/96/EC.2.Alle elektriske og elektroniske produkter skalsmides ud et andet sted end gennem denkommunale affaldsordning ved hjælp af specielleindsamlingsfaciliteter, der er organiseret af staten1.Si en un producto aparece el símbolo de un contenedorde basura tachado, significa que éste se acoge a laDirectiva 2002/96/CE.2.Todos los aparatos eléctricos o electrónicos se debendesechar de forma distinta del servicio municipal derecogida de basura, a través de puntos de recogidadesignados por el gobierno o las autoridades locales.3.La correcta recogida y tratamiento de los dispositivosinservibles contribuye a evitar riesgos potenciales para elmedio ambiente y la salud pública.4.Para obtener más información sobre cómo deshacerse desus aparatos eléctricos y electrónicos viejos, póngase encontacto con su ayuntamiento, el servicio de recogida debasuras o el establecimiento donde adquirió el producto. Vanhojen laitteiden hävittäminenEntsorgung von AltgerätenSådan smider du dit gamle apparat ud∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜Cómo deshacerse de aparatos eléctricos yelectrónicos viejoseller de lokale myndigheder.3.Korrekt bortskaffelse af dit gamle apparat er medtil at forhindre mulige skadevirkninger på miljøetog menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse afdit gamle apparat kan fås ved at kontakte ditlokale kommunekontor, renovationsselskab ellerden butik, hvor du købte produktet. FinnishGermanDanishGreekSpanish4.Wilt u meer informatie over de verwijdering vanuw oude toestel? Neem dan contact op met uwgemeente, de afvalophaaldienst of de winkelwaar u het product hebt gekocht.
Regulatory Information cont. 10 PortugueseSlovakCzechCroatianHungarianPolish
Regulatory Information cont. 11EstonianLatvianLithuanian

Navigation menu