LG Electronics USA LD803H LCD Monitor User Manual users manaul

LG Electronics USA LCD Monitor users manaul

users manaul

APPENDIX G :FCC ID : BEJLD803HUSER’S MANUAL
Dell™ 1800FP Color Display User's Guide Information in this document is subject to change without notice. © 2001 Dell Computer Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation; Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation; VESA is a registered trademark of Video Electronics Standards Association; IBM is a registered trademark of International Business Machines Corporation; Adobe is a trademark of Adobe Systems Incorporated, which may be registered in certain jurisdictions. As an ENERGY STAR Partner, Dell Computer Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Other trademarks and trade names may be used in this document to refer to either the entitles claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own. Initial release:04/05/2002 Preface Safety Instructions Introduction Setup Using the Display Troubleshooting Specifications Regulatory Notices Warranty Documentation
Back to Contents Page Preface: Dell™ 1800FP Color Display User's Guide About This Guide • Notational Conventions About This Guide This guide is intended for anyone who uses the Dell 1800FP Color Display. It describes the display's features, setup, and operation. The sections are as follows: Safety Instructions lists safety information. Introduction gives an overview of the display’s features and provides an orientation to the display. Setup describes the initial setup process. Using the Display gives an overview of how to use the display. Troubleshooting provides tips and solutions for common problems. Specifications lists the technical specifications of the display. Regulatory lists regulatory certifications and notices. Warranty describes the warranty information for this product. Documentation provides additional documentation that supports this product. Notational Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority. Back to Contents Page NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the
Back to Contents Page Safety Instructions: Dell™ 1800FP Color Display User's Guide Read and follow these instructions when connecting and using your computer display: To help avoid damaging your computer, be sure that the voltage selection switch on the power supply is set to match the alternating current (AC) power available at your location: 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far Eastern countries such as Japan, South Korea, and Taiwan. 230 V/50 Hz in most of Europe, the Middle East, and the Far East Also be sure that your display is electrically rated to operate with the AC power available in your location. Never insert anything metallic into the display openings. Doing so may create the danger of electric shock. To avoid electric shock, never touch the inside of the display. Only a qualified technician should open the display's case. Never use your display if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep the cable away from where people could trip over it. Be sure to hold the plug, not the cable, when disconnecting the display from an electric socket. Openings in the display cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered. Also, avoid using the display on a bed, sofa, rug, or other soft surface. Doing so may block the ventilation openings in the bottom of the cabinet. If you put the display in a bookcase or some other enclosed space, be sure to provide adequate ventilation. Put your display in a location with low humidity and a minimum of dust. Avoid places like damp basement or dusty hallways. Do not expose the display to rain or use it near water (in kitchens, next to swimming pools, etc.). If the display accidentally gets wet, unplug it and contact an authorized dealer immediately. You can clean the display with a damp cloth when necessary, but be sure to unplug the display first. Place the display on a solid surface and treat it carefully. The screen is made of glass and can be damaged if dropped or sharply hit. Locate your display near an easily accessible electric outlet. If your display does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service center. Do not attempt to remove the back cover, as you will be exposed to a shock hazard. The back cover should only be removed by qualified service personnel. High temperatures can cause problems. Don't use your display in direct sunlight, and keep it away from heaters, stoves, fireplaces, and other sources of heat. Unplug the display when it is going to be left unused for an extended period of time. Unplug your display from the electric outlet before any service. Back to Contents Page WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.
Back to Contents Page Introduction: Dell™ 1800FP Color Display User's Guide Overview • Graphics Overview Congratulations on purchasing the Dell 1800FP Flat Panel Color Display. The 1800FP utilizes a 18.1-inch (45.97cm) Active Matrix TFT LCD that displays sharp and brilliant images of text and graphics with a maximum resolution up to 1280 x 1024 pixels. This display is optimal for Microsoft® Windows®, CAD/CAM/CAE, desktop publishing, spreadsheets, multimedia, and any other application that demands large screen size and high resolutions. The Dell 1800FP was designed for a wide variety of users ranging from the home, small office, or corporate environment. Those who require exceptional quality and reliability at an affordable price will appreciate the value that the Dell 1800FP provides. For more details see Specifications Section. Graphics The following links show various views of the display and its components. Front View Back View Bottom View Side View Back to Contents Page
Back to Contents Page Front View: Dell™ 1800FP Color Display User's Guide A. Input selection button Use this button to make Dsub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is Dsub. B. Menu buttons Use this button to enter or exit the On Screen Display. C. Up/down arrow buttons Select between OSD items and activates "Hot key" function for brightness adjustment. D. Left/Right arrow buttons Use these buttons to choose or adjust items in the On Screen Display and activates Hot Key function for contrast adjustment.
Back to Contents Page E. Select/Auto button -! Use this button to enter a selection in the On Screen Display. - Automatically adjust vertical position, horizontal position, pixel clock and phase. F. Power button and LED indicator Turn the display on/off and indicate the status of power management.
Back to Contents Page Back View: Dell™ 1800FP Color Display User's Guide 1.Power connector 2.15-pin D-sub input 3.DVI-D digital input 4. Kensington lock Back to Contents Page
Back to Contents Page Bottom View: Dell™ 1800FP Color Display User's Guide The base is attached when the display is shipped and can be removed. Back to Contents Page
Back to Contents Page Side View: Dell™ 1800FP Color Display User's Guide Back to Contents Page
Back to Contents Page Setup: Dell™ 1800FP Color Display User's Guide Tilt/Swivel Base Attaching the Cables Positioning the Display Maintenance Back to Contents Page
Back to Contents Page Tilt/Swivel Base: Dell™ 1800FP Color Display User's Guide Tilt/Swivel Base With the Tilt/ Swivel base, you can tilt and/or swivel the display for the most comfortable viewing angle. CAUTION: The base is attached when the display is shipped and can be removed. Back to Contents Page
Back to Contents Page Attaching the Cables: Dell™ 1800FP Color Display User's Guide Cable Connections On Back of Display and Computer 1. Turn off your computer and unplug its power cable. 2. Connect either the white (digital DVI-D) or the blue (analog D-SUB) display connector cable to the corresponding video port on the back of your computer. Do not use both cables on the same PC. The only case in which both cables can be used is if they are connected to two different PCs with appropriate video systems. (The graphics are for illustration only. System appearance may vary). 3. Connect the power cable for your display to the power port on the back of the display. 4. Plug the power cables of your computer and your display into a nearby outlet. 5. Turn on your display and computer. If your display displays an image, installation is complete. If it does not display an image, see Troubleshooting. Back to Contents Page
Back to Contents Page Positioning the Display: Dell™ 1800FP Color Display User's Guide Consider the following environmental factors when you are deciding how to position the display: If there are any woofer speakers near the display, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks, and telephones that are within 3 feet away of the display. If there were electronic devices removed, perform degauss again. Back to Contents Page
Back to Contents Page Maintenance: Dell™ 1800FP Color Display User's Guide To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. To clean your Midnight Gray display cabinet, avoid using detergent of any kind. Detergent leaves a milky film on plastics; particularly the darker colored ones. It is best to use a lightly dampened warm cloth to clean the cabinet. White powder substance, due to shipping, may appear on the plastic or near bezel edge. If you observe this, simply wipe it off. Darker color plastics may scratch and shows white scuff marks more than lighter-colored display. Handle your Midnight Gray display with care. Back to Contents Page WARNING: To avoid risk of electric shock, do not disassemble the display cabinet. Users cannot service the display. User maintenance is restricted to cleaning. NOTE: Before cleaning the display, unplug it from the electrical outlet.
Back to Contents Page Using the Display: Dell™ 1800FP Color Display User's Guide Setting the Optimal Resolution Controls and Indicators Back to Contents Page
Back to Contents Page Setting the Optimal Resolution: Dell™ 1800FP Color Display User's Guide For optimal display performance while using the Microsoft® Windows® operating systems, set the display resolution to 1280 x 1024 pixels by performing the following steps: 1. Click the Start button, point to Settings, and click Control Panel. 2. Double-click the Display icon in the Control Panel window, and then click the Settings tab. 3. In the Desktop area, move the slidebar to 1280 by 1024 pixels. Then click OK. Back to Contents Page
Back to Contents Page Controls and Indicators: Dell™ 1800FP Color Display User's Guide Overview • On Screen Display (OSD) Menu System • Automatic Save • OSD_Warning_Messages • LED_Indicators Overview Use the control buttons on the front of the display to adjust the characteristics of the image being displayed. As you use these buttons to adjust the controls, an on-screen display (OSD) shows their numeric values as they change. A. Input selection button Use this button to make Dsub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is Dsub. B. Menu button Use this button to enter or exit the On Screen Display. See access the Menu system. C. Up/down arrow buttons Select between OSD items and activates "Hot key" function for brightness adjustment. D. Left/Right arrow buttons Use these buttons to choose or adjust items in the On Screen Display and activates Hot Key function for contrast adjustment.
On Screen Display (OSD) Menu System Direct-Access Functions E. Select/Auto button Automatically adjust vertical position, horizontal position, pixel clock and phase. For best results, use this button when there is a full screen of detailed information, such as fine text, or the shutdown window (without shutting down the system). The following dialog will appear on a black screen as the display self-adjusts to the current input: See Auto adjustment. Note: Auto Adjust will not occur if you press the button while there are no active video input signals, or attached cables. F. Power button and LED indicator Turn the display on/off and indicate the status of power management. The power indicator lights steady green while the display function normally. The LED is steady amber for DPMS. See Power management mode. Function Adjustment Method Auto adjustment: Even though your computer system can recognize your new flat panel display on startup, the 'Auto Adjustment' function will optimize the display settings for use with your particular setup. Auto Adjustment can be accessed through the OSD via the Image Settings submenu pictured at left or, you may use the direct access instructions below: 1.Turn on your computer and display. 2.Push the 'Select/Auto' button (E) to activate the Auto adjustment function. 3.When finished, the pixel clock and phase should be adjusted to their optimal settings.
Accessing the Menu System 1. With the menu off, push the MENU button to open the OSD system and display the main features menu. 2. OSD main menu has 5 sub-menus including “Brightness/Contrast”, “Color”, “Position”, “Tracking” and “Setup”. Push the up and down arrow buttons to move between the function icons. As you move from one icon to another, the Brightness: The Brightness function adjusts the luminance of the flat panel. With the menu off, push the up(or down) arrow button to display the Brightness adjustment menu. Adjust Brightness first, then adjust Contrast only if further adjustment is necessary. increase luminance decrease luminance Contrast: The Contrast function adjusts the degree of difference between darkness and lightness on the display screen. With the menu off, push the left(or right) arrow button to display the Contrast adjustment menu. increase the contrast decrease the contrast Controls Locked/Unlocked : Menu and : This function allows you to secure the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button and !button for 3 seconds: the message “CONTROLS LOCKED” appears. You can unlock the OSD controls at any time by pushing the MENU button and !button for 3 seconds: the message “CONTROLS UNLOCKED” will appear. A Sub-menu icon B Sub-menu name
function name is highlighted to reflect the function or group of functions (sub-menus) represented by that icon. See the table below for a complete list of all the functions available for the display. 3. Push the MENU button once to activate the highlighted function; then use the left and right buttons or the up and down arrow buttons, according to the indicators on the menu, to make your changes. 4. Push the Menu button once to return to the main menu to select another function or push the Menu button two or three times to exit from the OSD. Main Menu Mode Grouped by functions, the OSD offers 5 major functions in Main Menu for making adjustments: “Brightness/Contrast”, “Color”, “Position”, “Tracking” and “Setup”. The following describes the contents of each function and how you can make adjustments. enu Icon Adjustment Brightness: Adjust the brightness of the screen. increase luminance decrease luminance Contrast: Adjust the contrast of the screen. increase the contrast decrease the contrast hen you enter the Color Settings submenu, this page will show p if current input is D-sub or DVI-D. Color temperature is a easure of the 'warmth' of the image colors (red/green/blue). The ailable range is between 6500 to 9300K. You can select one of e 2 Preset Color temperature to see how each range suits your e or utilize the RED/GREEN/BLUE' option to customize the color ttings to your exact choice. 9300K This preset color temperature favors bluesRGB(6500K) This preset color temperature favors red cRED GREEN BLUE User Preset: You can adjust the Red, Green and Blue independently to fit your preference. decrease the brightness of the specific increase the brightness of the specific c Horizontal Position: Adjust the horizontal position of the displa moves the screen left moves the screen right
ositioning moves the viewing area around on the display screen. hen making changes to either the'Horizontal'or'Vertical' Vertical Position: Adjust the vertical position of the display. moves the screen down moves the screen up he Clock and Phase adjustments allow you to more closely just your display to your preference. These settings are cessed through the main OSD menu, by selecting 'Tracking'. satisfactory results are not obtained using the Phase adjustment, e the Clock adjustment and then use Phase again. Note: This function may change the width of the display image. Use the Horizontal function of the Position menu to center the display image on the screen. Clock: This function only applies to D-sub inpusub signal inputs into the display, it will bto a digital signal through a signal samplIt is rare , although possible, that thinterval is not automatically optimized. Iyou might see abnormal image displascreen. You can adjust the samplimanually through Pixel Clock function. decrease the sampling interval increase the sampling interval Phase: Just like Pixel Clock function, you can alssampling phase. decrease phase shift of sampling signa increase phase shift of sampling signal Language: To choose the language in which the control ndisplayed. Image Size: This function displays the image in its original enlarged size so as to fit in the full screen of thpanel. OSD Position: To adjust position of the OSD window on the s Signal: To select DSUB ANALOG, DVI DIGITAL ANALOG / as the active input. This featurwhen two computers are connected to theThe display automatically detects the prowhen only one video source is connected
Automatic Save With the OSD open, if you make an adjustment and then either proceed to another menu or exit the OSD, the display automatically saves any adjustments you have made. If you have made no adjustments, the on-screen menu disappears and the display does not save any new settings. OSD Warning Messages Self-Test Feature Check (STFC) The floating 'Dell - Self Test Feature Check' dialog will appear on-screen (against a black background) under the following conditions: First, if the display is powered on with no signal input attached, with any of the inputs selected. Second, if the signal cable is already attached, display is powered on, display is working properly, then the video cable is detached. This is true for any inputs selected. The display should stay in STFC mode until the input selection button is pressed to select an image source which is active, or the cable is re-attached. For the DB15 analog or DVI-D digital inputs, this case will put the display in power save or DPMS (see next section). In Power Save Mode When the computer system send DPMS signals for display power management, the display will show the message of “Power Saving Mode” for 10 seconds then enter power saving mode. This occurs when the DB15 analog or DVI-D digital input is connected and selected, but the computer source has gone inactive. While the display is in power saving mode, the screen will remain black. You can press any key or move mouse to reactivate the display. Input Signal Out of Range Factory Reset: Return you display settings to those set amanufacturing. Press button to activate
This means that the display cannot synchronize with the signal that it is receiving from the computer. Either the signal is too high or too low frequency for the display to use. See Specifications for the Horizontal and Vertical scan ranges addressible by this display. Sometimes, no warning message appears, but the screen is blank, which could also indicate that the display is not synchronizing with the computer. LED Indicators See Troubleshooting for more information. Back to Contents Page Display State LED stateOn Power management indicator is greenDPMS Power management indicator is amberSelected Input Mode LED stateD-Sub Input LED 1 is steady greenDVI-D Input LED 2 is steady green
Back to Contents Page Troubleshooting: Dell™ 1800FP Color Display User's Guide Display Specific Troubleshooting • Common Problems • Product Specific Problems Display Specific Troubleshooting Self-Test Feature Check (STFC) Your display provides a self-test feature that allows you to check whether your display is functioning properly. If your display and computer are properly connected but the display screen remains dark, run the display self-test by performing the following steps: 1. Turn off both your computer and the display. 2. Unplug the video cable from the back of the computer. 3. Turn on the display. If the display is functioning properly, you will see the STFC pattern. 4. While in self-test mode, the power management indicator remains green and the STFC pattern scroll through the screen. 5. Turn off your display and reconnect the video cable; then turn on both your computer and the display. If your display screen still remains dark after you use the previous procedure, check your video controller and computer system; your display is functioning properly. Power Saving Mode When the computer system is under power saving mode, the display will show the message of “Power Saving Mode”. Then press any key to reactivate the PC system.
Common Problems The following table contains general information about common display problems you might encounter. COMMON SYMPTOMS WHAT YOU SEE POSSIBLE SOLUTIONS No Video/ Power LED off No picture, display’s dead. Check connection integrity Electric outlet verification No Video/ Power LED on No picture or no brightness Increase brightness & contrast controls Perform display self test feature check Check for bent or broken pins on the signal cable Make sure the correct video input source is selected Poor Focus Picture is fuzzy, blurry or ghosting Push Auto key Adjust Phase and Clock controls via OSD Eliminate video extension cables Perform display reset Decrease brightness & contrast controls Lower video resolution or increase font size Shaky/Jittery Video Wavy picture or fine movement Push Auto key Adjust Phase and Clock controls via OSD Perform display reset Missing Pixels LCD screen has spots Cycle power on-off These are some pixels that are permanently offand is normal in LCD technology Stuck-on Pixels LCD screen has bright spots Cycle power on-off These are some pixels that are permanently onand is normal in LCD technology Brightness Problems Picture too dim or too bright Perform display reset Adjust brightness & contrast controls Geometric Distortion Screen not centered correctly Push Auto key Adjust the centering controls Perform display reset Ensure display is in proper video mode Horizontal/Vertical Lines Screen has one or more lines Perform display reset Adjust Phase and Clock controls via OSD Push Auto key Perform display self test feature check Check for bent or broken pins Sync Problems Screen is scrambled or appears torn Adjust Phase and Clock controls via OSD Push Auto key Perform display self test feature check Check for bent or broken pins If using Microsoft® Windows®, boot up in the "safe mode" LCD Scratched Screen has scratches or smudges Turn display off and clean the screen
Product Specific Problems Back to Contents Page Safety Related Issues Visible signs of smoke or sparks Do not perform any troubleshooting steps Display needs to be replaced Intermittent Problems Display malfunctions on & off Ensure display is in proper video mode Ensure video cable connection is secure Perform display reset Perform display self test feature check SPECIFIC SYMPTOMS WHAT YOU SEE POSSIBLE SOLUTIONS Cannot adjust the display with the buttons on the front panel OSD does not appear on the screen Disconnect AC power from the display, wait fiveminutes and then re-connect AC power Screen image is too small Image is centered on screen, but does not fill entire viewing area Adjust the Scaling feature via the OSD and select Fill. This feature is located under Image Settings
Back to Contents Page Specifications: Dell™ 1800FP Color Display User's Guide General • Flat Panel • Resolution • Preset Display Modes • Electrical • Physical Characteristics • Environmental • Power Management Modes • Pin_Assignments • Plug_and_Play_Capability General Model number 1800FP Flat Panel Screen type Active matrix - TFT LCD Screen dimensions Diagonal 18.1 inches (459.7 mm) Horizontal 14.14 inches (359.04 mm) Vertical 11.31 inches (287.23 mm) Pixel pitch 0.2805 mm Viewing angle +/- 80° (vertical) typical, +/- 80° (horizontal) typical Luminance output 250 CD/m2 typical, 200 CD/m2 minimum Contrast ratio 350 to 1 typical, 200 to 1 minimum LCD surface coating Hardness 3H, antiglare treatment Backlight 6 CCFL type Resolution Horizontal scan range Analog: 31 - 80 kHz (automatic) Digital: 31 – 70kHz (automatic) Vertical scan range 55 Hz to 85 Hz (automatic) Optimal preset resolution 1280 x 1024 at 60 Hz Highest preset resolution 1280 x 1024 at 75 Hz Dell guarantees image size and centering for all preset modes listed in the following table. Preset Display Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal / Vertical) VGA, 640 x350 31.469 70 25.175 + VGA, 720 x 400 31.468 70 28.321 - VGA, 640x480 31.469 60 25.175 - VESA, 640 x 480 37.500 75 31.5 - VESA, 640 x 480 43.269 85 36.0 -
VESA, 800 x 600 37.879 60 40.0 + VESA, 800 x 600 46.875 75 49.5 + VESA, 800 x 600 53.674 85 56.25 + MAC, 832 x 624 49.725 75 57.283 +/- VESA, 1024 x 768 48.363 60 65.0 - VESA, 1024 x 768 60.123 75 78.75 - VESA, 1024 x 768 68.677 85 94.5 + MAC, 1152 x 864 67.5 75 108.0 +/- VESA, 1152 x 900 61.805 65 92.978 +/- VESA, 1280 x 1024 63.981 60 108.0 + VESA, 1280 x 1024 79.976 75 135.0 + Electrical Video input signals Analog RGB, 0.7 Volts +/-5%, 75 ohm input impedance Digital DVI-D TMDS, 600mV for each differential line, 50 ohm input impedance Synchronization input signals separate horizontal and vertical; 3.3V Cmos or 5V TTL level, positive or negative sync. Sync on Green Compsite Sync AC input voltage / frequency / current 90 ~264 VAC/ 50/60 Hz 1.0 (RMS) max Inrush current at 120 V 30 A max Inrush current at 220 V 50 A max Physical Characteristics Connector type 15-pin D-subminiature; DVI-D Signal cable type Detached to display Dimensions:(with stand) Height 16.97inches (431mm ) Width 15.98inches (406mm ) Depth 8.78inches (223mm ) Weight (display only) 17.19 lb (7.8 kg ) Weight (with packaging) 22.05 lb (10 kg )
Power Management Modes If you have VESA's DPMS compliant display card or software installed in your PC, the display can automatically reduce its power consumption when not in use. If input from keyboard, mouse or other input devices is detected, the display will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving feature: This display is ENERGY STAR®-compliant . * Zero power consumption in OFF mode can only be achieved by disconnecting the mains cable from the display. ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, DELL has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Environmental Temperature: Operating 41° to 95°F (5° to 35 °C ) Nonoperating -4° to 140°F (-20° to 60°C ) Humidity: Operating 10% to 80% (noncondensing) Nonoperating 5% to 95% (noncondensing) Altitude: Operating 3,048 m (12,000 ft) Nonoperating 12,192 m (40,000 ft) Thermal dissipation 213 BTU/hour (maximum) 205 BTU/hour (typical) Power Management Definition VESA's Mode Video H-sync V-sync Power Used Power Saving LED color ON Active Yes Yes maximum 55W normal 50W 0% Green Stand-by Blanked No Yes <=3W >80% Amber Suspend Blanked Yes No <=3W >80% Amber Active-OFF* Blanked No No <=1W >80% Amber
Pin Assignments 15-pin D-sub connector 24 pin DVI-D connector Pin Number 15-Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 GND 5 Self-test 6 GND-R 7 GND-G 8 GND-B 9 +5V Supply 10 GND-sync 11 GND 12 SDA 13 H-sync 14 V-sync 15 SCL Pin Number 24-Pin Side of the Signal Cable 1 TMDS Data2- 2 TMDS Data2+
Plug and Play Capability You can install the display in any Plug and Play-compatible system. The display automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the display settings. If desired, the user can select different settings, but in most cases display installation is automatic. Back to Contents Page 3 TMDS Data 2/4 Shield 4 TMDS Data4- 5 TMDS Data4+ 6 DDC Clock 7 DDC Data 8 Analog Vertical Sync 9 TMDS Data1- 10 TMDS Data1+ 11 TMDS Data 1/3 Shield 12 TMDS Data3- 13 TMDS Data3+ 14 +5V Power 15 Ground(Return for +5V, H sync and V sync) 16 Hot Plug Detect 17 TMDS Data 0- 18 TMDS Data0+ 19 TMDS Data 0/5 Shield 20 TMDS Data 5- 21 TMDS Data5+ 22 TMDS Clock Shield 23 TMDS Clock+ 24 TMDS Clock-
Back to Contents Page Regulatory: Dell™ 1800FP Color Display User's Guide Electric and Magnetic Fields • Energy Efficiency • Federal Communications Commission (FCC) Notice (U.S. Only) • FCC Declaration of Conformity • CE Declaration of Conformity • Canadian Regulatory Information (Canada Only) • EN 55022 Compliance (Czech Republic Only) • VCCI Class 2 Notice (Japan Only) • MIC Notice (South Korea Only) • Polish Center for Testing and Certification Notice • NOM Information (Mexico Only) • BSMI Notice • Ergonomics Notice (Germany Only) Dell Computer Corporation's Environmental Program • Regulatory Listing Electric and Magnetic Fields Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labeled computers? In many countries, environmental labeling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy. What does labeling involve? This product meets the requirements for the TCO'95 scheme which provides for international and environmental labeling of personal computers. The labeling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety. The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labeled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability.
Energy Efficiency Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'95 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'95 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'95 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'95 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO'95 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed. _____________________________ * Bio-accumulative is defined as substances which accumulate within living organisms ** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
Federal Communications Commission (FCC) Notice (U.S. Only) WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. Instructions to Users: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that following conditions are met. 1. Power cable: Shielded power cable must be used. 2. Video inputs: The input signal amplitude must not exceed the specified level. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The proper operation of the function requires a computer with VESA DPMS power management capabilities. When used with a computer equipped with VESA DPMS, the display is ENERGY STAR-compliant. As an ENERGY STAR Partner, Dell Computer Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. FCC Declaration of Conformity According to 47 CFR, Part 15 of the FCC Rules * For the following named product:COLOR DISPLAY (Category Name) 2000FP / DELL FP2036 (Model No / Brand Name) (Basic Model) * Manufactured at: Acer Communications & Multimedia Inc. 157 Shanying Road, Gueishan, Taoyuan 333, Taiwan, R.O.C. We hereby declare that this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. * FCC Rules: Tested to comply with FCC part 15, class B* Test site at: Compliance Engineering Services, Sunnyvale, CA, USA* Responsible Party for Product Compliance: Acer Communications & Multimedia Inc.157, Shan-Ying Road, Gueishan, Taoyuan 333, Taiwan, R.O.C. Tel) 886-3-3598800 Fax) 886-3-3599000 * Manufacturer Information: Acer Communications & Multimedia Inc. 157, Shan-Ying Road, Gueishan, Taoyuan 333 2001-4-26 Ray Huang / Products Regulatory Manager (Place and date of issue) (Name and signature of authorized person)CE DECLARATION OF CONFORMITYFOR A CLASS B DIGITAL DEVICE Directives to which conformity is declared EMC Directives 89/336/EEC and amending directive 92/31/EEC And Low Voltage Directive 73/23/EEC Standards to which conformity is declared EN55022: 1998; EN55024: 1998; EN60950 +A1+A2+A3+A4: 1992; EN61000-3-2: 1995; EN61000-3-3: 1995 Manufacturer's Name: Acer Communications&Multimedia Inc. Manufacturer's Address: 157, Shan-Ying Road, Gueishan, Taoyuan 333, Taiwan, R.O.C. Importer's Address: Type of Equipment: Display Model Number(s): 2000FP Reference Report Number: Previously Declared Models: I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and standards. Place: Acer Communications&Multimedia Inc. 157, Shan-Ying Road, Gueishan, Taoyuan 333, Taiwan, R.O.C. Signature Date: 2001-4-27 Full Printed Name RayHuang ProductsRegulatory
Canadian Regulatory Information (Canada Only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by Dell Computer Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. EN 55022 Compliance (Czech Republic Only) VCCI Class 2 Notice (Japan Only) This equipment complies with the limits for a Class 2 digital device (devices used in or adjacent to a residential environment) and conforms to the standards for information technology equipment that are set by the Voluntary Control Council for Interference for preventing radio frequency interference in residential areas. Class B ITE MIC Notice (South Korea Only) B Class Device ManagerPosition/Title
Please note that this device has been approved for nonbusiness purposes and may be used in any environment, including residential areas. Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible. A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251. NOM Information (Mexico Only) The following information is provided on the device(s) described in this document in compliance with the requirements of the official Mexican standards (NOM) Dell Computer Corporation
Información para NOM (únicamente para México) La información siguiente se proporciona en el dispositivo o en los dispositivos descritos en este documento, en cumplimiento con los requisitos de la Norma Oficial Mexicana (NOM): BSMI Notice (Taiwan Only) Ergonomics Notice (Germany Only) Under the requirements of German ergonomics standard EK1/59-98, EK1-60-98, ISO 9241-3/8, graphics or characters: 1. Blue graphics or characters in dark background are not recommended. (This combination may increase eye fatigue due to poor visibility caused by low contrast.) 2. Graphics controller and monitor are recommended to be used in the following conditions: Vertical frequency: 70 Hz or higher. Display mode: Dark characters in bright background. Ergonomie Hinweis (nur Deutschland) Um den Anforderungen der deutschen Ergonomie-Norm EK1/59-98, EK1-60-98, ISO 9241-3/8 zu antsprechen. Exporter: One Dell Way Round Rock, TX 78682 Importer: Dell Computer de México, Paseo de la Reforma 2620, 11th Floor Col. Lomas Altas Mexcio DF CP 11950 Ship to: Dell Computer de Mexico, S.A. de C.V. al Cuidado de Kuehne & de México S. de R.I., Avenida Soles No. 55Col. Peñn de los BaÑs, 15520 Mexico, D.F.Supply voltage: > 100/240 VAC Frequency: 50/60 Hz Current 1.2 A Exporter: Dell Computer Corporation One Dell Way Round Rock, TX 78682 Importador: Dell Computer de México, Paseo de la Reforma 2620, 11th Floor Col. Lomas Altas Mexcio DF CP 11950 Embarcar a: Dell Computer de México, S.A. de C.V. al Cuidado de Kuehne & Nagel de M?ico S. de R.I., Avenida Soles No. 55 Col. Peñon de los Baños, 15520 México, Tensión alimentación: 100/240 VACFrecuencia: 50/60 Hz Consumo de 1.2 A
1. Wird empfahlen, die Grunfarbe Blau nicht auf dunklem Hintergrund zu verwenden (schiechte Erkennbarkeit. Augenbelastung bei zu geringem Zeicheenkontrast). 2. Wird folgende Einstellung des Grafik-Controllers und Monitors empfohlen. Vertikalfrequenz : 70 Hz oder hoher. Ohne Zellensprung. Dell Computer Corporation's Environmental Program Please visit Dell's environmental Web site to learn more about Dell's environmental programs. Back to Contents Page Regulatory Listing Safety Certifications: UL 1950 NOM CE Mark—EN60950: 1992 + A1 + A2 + A3 NEMKO SEMKO DEMKO FIMKO EZU IEC 950 TUV GS PCBC GOST CCIB JEON PSB EMC Certifications: FCC Part 15 Class B CE Mark—EN55022:1998 Class B, EN61003-2:1995, EN61003-3:1995, EN55024:1998 EZU NEMKO SEMKO DEMKO FIMKO PCBC GOST C-Tick VCCI Class B ITE MIC BSMI Ergonomics: ENERGY STAR® TCO 95 GOST Hygienic
Back to Contents Page Warranties: Dell Service and Support Plan Guide, "Total Satisfaction" Return Policy (U.S. and Canada Only) Limited Warranties for Dell Branded Hardware Products • Limited Three-Year Warranty (U.S. Only) • Limited Three-Year Warranty (Canada Only) • One Year Dell Manufacturer End-User Guarantee European Union, Norway and Switzerland • "Total Satisfaction" Return Policy (U.S. and Canada Only) Limited Warranties for Dell Branded Hardware Products DELL-BRANDED HARDWARE PRODUCTS COME WITH A LIMITED WARRANTY. THE LIMITED WARRANTY COVERING YOUR PARTICULAR SYSTEM WILL BE NOTED ON YOUR INVOICE AND INCLUDED IN THE DOCUMENTATION ACCOMPANYING YOUR SYSTEM. DELL-BRANDED MONITORS PURCHASED INDEPENDENT OF A SYSTEM PURCHASE COME WITH THE LIMITED WARRANTY SET OUT BELOW. (For US customers, a copy of Dell's limited warranty statement can be obtained by writing Dell at USA L.P., Attn: Warranties, One Dell Way, Round Rock, TX 78682.) Limited Three-Year Warranty (U.S. Only) Dell Computer Corporation ("Dell") manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry-standard practices. Dell warrants that the hardware products it manufactures will be free from defects in materials and workmanship. The warranty term is three years beginning on the date of invoice, as described in the following text. Damage due to shipping the products to you is covered under this warranty. Otherwise, this warranty does not cover damage due to external causes, including accident, abuse, misuse, problems with electrical power, servicing not authorized by Dell, usage not in accordance with product instructions, failure to perform required preventive maintenance, and problems caused by use of parts and components not supplied by Dell. This warranty does not cover any items that are in one or more of the following categories: software; external devices (except as specifically noted); accessories or parts added to a Dell system after the system is shipped from Dell; accessories or parts added to a Dell system through Dell's system integration department; accessories or parts that are not installed in the Dell factory; or DellWareSM products. Displays, keyboards, and mice that are Dell-branded or that are included on Dell's standard price list are covered under this warranty; all other displays, keyboards, and mice (including those sold through the DellWare program) are not covered. Batteries for portable computers are covered only during the initial one-year period of this warranty.Coverage During Year One During the one-year period beginning on the invoice date, Dell will repair or replace products covered under this limited warranty that are returned to Dell's facility. To request warranty service, you must call Dell's Customer Technical Support within the warranty period. Refer to "Getting Help" in your Installation and Troubleshooting Guide to find the appropriate telephone number for obtaining customer assistance. If warranty service is required, Dell will issue a Return Material Authorization Number. You must ship the products back to Dell in their original or equivalent packaging, prepay shipping charges, and insure the shipment or accept the risk of loss or damage during shipment. Dell will ship the repaired or replacement products to you freight prepaid if you use an address in the continental U.S., where applicable. Shipments to other locations will be made freight collect. Dell owns all parts removed from repaired products. Dell uses new and reconditioned parts made by various manufacturers in performing warranty repairs and building replacement products. If Dell repairs or replaces a product, its warranty term is not extended. Coverage During Years Two and Three During the second and third years of this limited warranty, Dell will provide, on an exchange basis and subject to Dell's NOTE: Before you ship the product(s) to Dell, back up the data on the hard-disk drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as diskettes, CDs, or PC Cards. Dell does not accept liability for lost data or software.
Exchange Policy in effect on the date of the exchange, replacement parts for the Dell hardware product(s) covered under this limited warranty when a part requires replacement. You must report each instance of hardware failure to Dell's Customer Technical Support in advance to obtain Dell's concurrence that a part should be replaced and to have Dell ship the replacement part. Dell will ship parts (freight prepaid) if you use an address in the continental U.S. or Canada, where applicable. Shipments to other locations will be made freight collect. Dell will include a prepaid shipping container with each replacement part for your use in returning the replaced part to Dell. Replacement parts are new or reconditioned. Dell may provide replacement parts made by various manufacturers when supplying parts to you. The warranty term for a replacement part is the remainder of the limited warranty term. You will pay Dell for replacement parts if the replaced part is not returned to Dell. The process for returning replaced parts, and your obligation to pay for replacement parts if you do not return the replaced parts to Dell, will be in accordance with Dell's Exchange Policy in effect on the date of the exchange. You accept full responsibility for your software and data. Dell is not required to advise or remind you of appropriate backup and other procedures. General Provisions THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH VARY FROM STATE TO STATE (OR JURISDICTION TO JURISDICTION). DELL'S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS WARRANTY STATEMENT. ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER SUCH PERIOD. SOME STATES (OR JURISDICTIONS) DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE PRECEDING LIMITATION MAY NOT APPLY TO YOU. DELL DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES SET FORTH IN THIS WARRANTY STATEMENT OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION ANY LIABILITY FOR PRODUCTS NOT BEING AVAILABLE FOR USE OR FOR LOST DATA OR SOFTWARE. SOME STATES (OR JURISDICTIONS) DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE PRECEDING EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. These provisions apply to Dell's limited three-year warranty only. For provisions of any service contract covering your system, refer to your invoice or the separate service contract that you will receive. If Dell elects to exchange a system or component, the exchange will be made in accordance with Dell's Exchange Policy in effect on the date of the exchange. In any instance in which Dell issues a Return Material Authorization Number, Dell must receive the product(s) for repair prior to the expiration of the warranty period in order for the repair(s) to be covered by the warranty. Limited Three-Year Warranty (Canada Only) Dell Computer Corporation ("Dell") manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry-standard practices. Dell warrants that the hardware products it manufactures will be free from defects in materials and workmanship. The warranty term is three years beginning on the date of invoice, as described in the following text. Damage due to shipping the products to you is covered under this warranty. Otherwise, this warranty does not cover damage due to external causes, including accident, abuse, misuse, problems with electrical power, servicing not authorized by Dell, usage not in accordance with product instructions, failure to perform required preventive maintenance, and problems caused by use of parts and components not supplied by Dell. This warranty does not cover any items that are in one or more of the following categories: software; external devices (except as specifically noted); accessories or parts added to a Dell system after the system is shipped from Dell; accessories or parts added to a Dell system through Dell's system integration department; accessories or parts that are not installed in the Dell factory; or DellWareSM products. Displays, keyboards, and mice that are Dell-branded or that are included on Dell's standard price list are covered under this warranty; all other displays, keyboards, and mice (including those sold through the DellWare program) are not covered. Batteries for portable computers are covered only during the initial one-year period of this warranty.Coverage During Year One NOTE: If you chose one of the available warranty and service options in place of the standard limited three-year warranty described in the preceding text, the option you chose will be listed on your invoice.
During the one-year period beginning on the invoice date, Dell will repair or replace products covered under this limited warranty that are returned to Dell's facility. To request warranty service, you must call Dell's Customer Technical Support within the warranty period. Refer to "Getting Help" in your Installation and Troubleshooting Guide to find the appropriate telephone number for obtaining customer assistance. If warranty service is required, Dell will issue a Return Material Authorization Number. You must ship the products back to Dell in their original or equivalent packaging, prepay shipping charges, and insure the shipment or accept the risk of loss or damage during shipment. Dell will ship the repaired or replacement products to you freight prepaid if you use an address in Canada, where applicable. Shipments to other locations will be made freight collect. Dell owns all parts removed from repaired products. Dell uses new and reconditioned parts made by various manufacturers in performing warranty repairs and building replacement products. If Dell repairs or replaces a product, its warranty term is not extended. Coverage During Years Two and Three During the second and third years of this limited warranty, Dell will provide, on an exchange basis and subject to Dell Exchange Policy in effect on the date of the exchange, replacement parts for the Dell hardware product(s) covered under this limited warranty when a part requires replacement. You must report each instance of hardware failure to Dell's Customer Technical Support in advance to obtain Dell's concurrence that a part should be replaced and to have Dell ship the replacement part. Dell will ship parts (freight prepaid) if you use an address in the continental U.S. or Canada, where applicable. Shipments to other locations will be made freight collect. Dell will include a prepaid shipping container with each replacement part for your use in returning the replaced part to Dell. Replacement parts are new or reconditioned. Dell may provide replacement parts made by various manufacturers when supplying parts to you. The warranty term for a replacement part is the remainder of the limited warranty term. You will pay Dell for replacement parts if the replaced part is not returned to Dell. The process for returning replaced parts, and your obligation to pay for replacement parts if you do not return the replaced parts to Dell, will be in accordance with Dell's Exchange Policy in effect on the date of the exchange. You accept full responsibility for your software and data. Dell is not required to advise or remind you of appropriate backup and other procedures. General Provisions DELL MAKES NO EXPRESS WARRANTIES OR CONDITIONS BEYOND THOSE STATED IN THIS WARRANTY STATEMENT. DELL DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SOME STATES (OR JURISDICTIONS) DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES OR CONDITIONS, SO THIS LIMITATION MAY NOT APPLY TO YOU. DELL'S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS WARRANTY STATEMENT. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE (OR JURISDICTION TO JURISDICTION). DELL DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES SET FORTH IN THIS WARRANTY STATEMENT OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION ANY LIABILITY FOR PRODUCTS NOT BEING AVAILABLE FOR USE OR FOR LOST DATA OR SOFTWARE. SOME STATES (OR JURISDICTIONS) DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE PRECEDING EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. These provisions apply to Dell's limited three-year warranty only. For provisions of any service contract covering your system, refer to your invoice or the separate service contract that you will receive. If Dell elects to exchange a system or component, the exchange will be made in accordance with Dell's Exchange Policy in effect on the date of the exchange. In any instance in which Dell issues a Return Material Authorization Number, Dell must receive the product(s) for repair prior to the expiration of the warranty period in order for the repair(s) to be covered by the warranty. NOTE: Before you ship the product(s) to Dell, back up the data on the hard-disk drive(s) and any other storage device(s) in the product(s). Remove any removable media, such as diskettes, CDs, or PC Cards. Dell does not accept liability for lost data or software.NOTE: If you chose one of the available warranty and service options in place of the standard limited three-year warranty described in the preceding text, the option you chose will be listed on your invoice.
One Year Dell Manufacturer End-User Guarantee European Union, Norway and Switzerland Guarantee DELL Products, Raheen Industrial Estate, Limerick, Ireland (DELL) warrants to the end-user in accordance with the following provisions that its branded hardware products, purchased by the end-user from a DELL company or an authorized DELL distributor, in the European Union, Norway or Switzerland, will be free from defects in materials, workmanship and design affecting normal use, for a period of one year as of the original purchase date. Products for which proper claims are made will, at DELL’s option, be repaired or replaced at DELL’s expense. Exclusions This Guarantee does not apply to defects resulting from: improper or inadequate installation, use or maintenance; actions or modifications by unauthorized third parties or the end-user; accidental or wilful damage or normal wear and tear. Making a claim Claims must be made in the European Union, Norway or Switzerland, by contacting the point of sale or any DELL office within the guarantee period. The end-user must always supply proof of purchase, indicating name and address of the seller, date of purchase, model and serial number, name and address of the customer and details of symptoms and configuration at time of malfunction, including peripherals and software used. Otherwise, DELL may refuse the guarantee claim. Upon diagnosis of a warranted defect, DELL will make arrangements, and pay for ground freight and insurance to and from DELL repair/ replacement centre. End-user must ensure defective product is available for collection properly packed in original or equally protective packaging together with details listed above and the return number provided to the end-user by DELL. Limitation and Statutory Rights DELL makes no other warranty, guarantee or like statement other than as explicitly stated above and this Guarantee is given in place of all other guarantees whatsoever, to the fullest extent permitted by law. In the absence of applicable legislation, this Guarantee will be the end-user’s sole and exclusive remedy against DELL or any of its affiliates, and neither DELL nor any of its affiliates shall be liable for loss of profit or contracts, or any other indirect or consequential loss arising from negligence, breach of contract, or howsoever. This Guarantee does not impair or affect mandatory statutory rights of the end-user against and/or any rights resulting from other contracts concluded by the end-user with DELL and/or any other seller. General Provisions DELL MAKES NO EXPRESS WARRANTIES OR CONDITIONS BEYOND THOSE STATED IN THIS WARRANTY STATEMENT. DELL DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SOME STATES (OR JURISDICTIONS) DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES OR CONDITIONS, SO THIS LIMITATION MAY NOT APPLY TO YOU. DELL’S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS WARRANTY STATEMENT. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE (OR JURISDICTION TO JURISDICTION). DELL DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES SET FORTH IN THIS WARRANTY STATEMENT OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION ANY LIABILITY FOR PRODUCTS NOT BEING AVAILABLE FOR USE OR FOR LOST DATA OR SOFTWARE. SOME STATES (OR JURISDICTIONS) DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE PRECEDING EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. These provisions apply to Dell’s limited three-year warranty only. For provisions of any service contract covering your system, refer to your invoice or the separate service contract that you will receive. "Total Satisfaction" Return Policy (U.S. and Canada Only) If you are an end-user customer who bought new products directly from a Dell company, you may return them to Dell within 30 NOTE: If you chose one of the available warranty and service options in place of the standard limited three-year warranty described in the preceding text, the option you chose will be listed on your invoice.
days of the date of invoice for a refund or credit of the product purchase price. If you are an end-user customer who bought reconditioned or refurbished products from a Dell company, you may return them to Dell within 14 days of the date of invoice for a refund or credit of the product purchase price. In either case, the refund or credit will not include any shipping and handling charges shown on your invoice. If you are an organization that bought the products under a written agreement with Dell, the agreement may contain different terms for the return of products than specified by this policy. To return products, you must call Dell Customer Service to receive a Credit Return Authorization Number. Refer to "Getting Help" in your Installation and Troubleshooting Guide to find the appropriate telephone number for obtaining customer assistance. To expedite the processing of your refund or credit, Dell expects you to return the products to Dell in their original packaging within five days of the date that Dell issues the Credit Return Authorization Number. You must also prepay shipping charges and insure the shipment or accept the risk of loss or damage during shipment. You may return software for refund or credit only if the sealed package containing the diskette(s) or CD(s) is unopened. Returned products must be in as-new condition, and all of the manuals, diskette(s), CD(s), power cables, and other items included with a product must be returned with it. For customers who want to return, for refund or credit only, either applications software or an operating system that has been installed by Dell, the whole system must be returned, along with any media and documentation that may have been included in the original shipment. This "Total Satisfaction" Return Policy does not apply to DellWare products, which may be returned under DellWare's then-current return policy. In addition, reconditioned parts purchased through Dell Spare Parts Sales in Canada are nonreturnable. Back to Contents Page .
Back to Contents Page Documentation: Dell™ 1800FP Color Display User's Guide You must right-click the link for a portable document format (PDF) file and save the file to your hard-disk drive. Attempting to link directly to large PDF files causes your system to freeze. To save PDF files (files with an extension of .pdf) to your hard-disk drive, right-click the document title, click Save Target As in Microsoft® Internet Explorer or Save Link As in Netscape Navigator, and specify a location on your hard-disk drive. Right-click only the following link: "Quick Set-up" (.pdf) To view a PDF file, launch Adobe™ Acrobat Reader. Click File —> Open and select the PDF file. Back to Contents Page NOTE: PDF files require Adobe Acrobat Reader, which can be downloaded from the Adobe World Wide Web site.

Navigation menu