LG Electronics USA LGHAWWW1301 WLAN module User Manual EMISSION TEST REPORT

LG Electronics USA WLAN module EMISSION TEST REPORT

Updated Manual

Order Number : GETEC-C1-13-029 CANADA IC Test Report Number : GETEC-E4-13-019 Page 1 / 1 EUT Type: WLAN module IC: 2703N-LGHAWWW1301 APPENDIX G : USER’S MANUAL
LGHA-WWW1301 WLAN Dongle User Manual
HB-RND-xxA 2 페이지 2013-03-13 - 2 -박병만 2 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 2/13 Pages 1 Information 1.1 Feature LGHA-WWW1301 is WLAN Dongle support USB2.0 A type Interface. Because It support USB2.0 interface, Therefore you can connect to the host system it easily LGHA-WWW1301 use MURATA MODUEL(PARTNAME:LBWA17XQXZ-450) MURATA MODULE use BCM4319(BroadCom) LGHA-WWW1301 support IEEE802.11b/g/n and data rate 65Mbps 1.2 Module Summary ㆍ 2.4GHz IEEE 802.11b/g/n Radio Technology ㆍ On-board Antenna ㆍ Transmit power : +18dBm @ 11b/11Mbps ㆍ Max Receive Sensitivity : -92dBm ㆍ MURATA Module applied ( RF CHIPSET : BCM4319 ) ㆍ USB2.0 A Type Interface ㆍ Operating Temperature Range : -20°C to 70°C ㆍ ROHS compliant 1.3 Block Diagram Fig.1 System Block Diagram
HB-RND-xxA 3 페이지 2013-03-13 - 3 -박병만 3 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 3/13 Pages 2 Module Outline 2.1 Module Dimension Fig. 2 LGHA-WWW1301 Dimension (Unit : mm) 2.2 Component Placement Fig.3 LGHA-WWW1301 Component Placement ANCG12G44SAA145RD1 LBWA17XQXZ-450
HB-RND-xxA 4 페이지 2013-03-13 - 4 -박병만 4 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 4/13 Pages 3 MURATA LBWA17XQXZ-450 MURATA's WLAN Module LBWA17XQXZ-450 WLAN chipset, RF Switch, Filter, etc. are included. Broadcom's WLAN chipset bcm4319 was used. SDIO Interface and USB Interface is supported 30MHz external clock operation. Fig.4 LBWA17XQXZ-450 Block Diagram 4 RF Specifications 4.1 RF Specifications Summary Items Contents Support IEEE802.11b/g/n, WLAN compliant Frequency Range 2400 ~ 2483.5 MHz Modulation DSSS, CCK, OFDM Channel 1~11ch (2412 ~ 2462 MHz) Data Rate 802.11b = 1, 2, 5.5, 11 Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11n = 6.5, 13, 19.5, 26, 39, 52, 58.5, 65 Mbps Target Max Output Power(Peak) 802.11b = 18 dBm 802.11g = 19 dBm 802.11n = 17 dBm Antenna On Board SMD Antenna, 50 ohm Table.1 LGHA-WWW1301 RF Specification Summary
HB-RND-xxA 5 페이지 2013-03-13 - 5 -박병만 5 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 5/13 Pages 4.2 IEEE 802.11b Mode Items Contents Specification IEEE802.11b Mode DSSS / CCK Frequency 2400 – 2483.5 MHz Data rate 1, 2, 5.5, 11 Mbps Target Max Output Power 18dBm DC Characteristics Min. Typ. Max. unit 1. DC current 1) Tx mode (1024byte, 20usec interval) 300 mA 2) Rx mode 77 mA Tx Characteristics Min. Typ. Max. unit 2. Power Levels 16 18 20 dBm 3. Spectrum Mask 1) Fc ± 11MHz -40 -30 dBr 2) Fc ± 20MHz -54 -50 dBr 4. RF Carrier Suppression -15 dB 5. Modulation Accuracy(EVM) 17 35 % 6. OBW(Occupied Bandwidth) 20 MHz 7. Outband Spurious Emissions 1) 30Mhz to 1 Ghz(BW=100kHz) tbd dBm 2) 1Ghz to 12.75 Ghz(BW=100kHz) tbd dBm 3) 1.8Ghz to 1.9 Ghz(BW=100kHz) tbd dBm 4) 5.5Ghz to 5.3 Ghz(BW=100kHz) tbd dBm Rx Characteristics Min. Typ. Max. unit 8. Minimum input Level Sensitivity 1) 1Mbps (FER ≤ 8%) -92 -80 dBm 2) 11Mbps (FER ≤ 8%) -85 -76 dBm 9. Maximum Input Level (FER ≤ 8%) -10 dBm 10. Adjacent Channel Rejection (FER ≤ 8%) tbd dB Table.2 IEEE 802.11b Mode Specification
HB-RND-xxA 6 페이지 2013-03-13 - 6 -박병만 6 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 6/13 Pages 4.3 IEEE 802.11g Mode Items Contents Specification IEEE802.11g Mode OFDM Frequency 2400 – 2483.5 MHz Data rate 6, 9, 12, 18, 24, 36, 48, 54 Mbps Target Max Output Power 19dBm DC Characteristics Min. Typ. Max. unit 1. DC current 1) Tx mode (1024byte, 20usec interval) 237 mA 2) Rx mode 77 mA Tx Characteristics Min. Typ. Max. unit 2. Power Levels 17 19 21 dBm 3. Spectrum Mask 1) Fc ± 11MHz -34 -20 dBr 2) Fc ± 20MHz -50 -28 dBr 3) Fc ± 30MHz -58 -40 dBr 4. Constellation Error (EVM) 1) 6 Mbps -30 -5 dB 2) 24 Mbps -30 -16 dB 3) 54 Mbps -30 -25 dB 5. Modulation Accuracy(EVM) 17 35 % 6. OBW(Occupied Bandwidth) 20 MHz 7. Outband Spurious Emissions 1) 30Mhz to 1 Ghz(BW=100kHz) tbd dBm 2) 1Ghz to 12.75 Ghz(BW=100kHz) tbd dBm 3) 1.8Ghz to 1.9 Ghz(BW=100kHz) tbd dBm 4) 5.5Ghz to 5.3 Ghz(BW=100kHz) tbd dBm Rx Characteristics Min. Typ. Max. unit 8. Minimum input Level Sensitivity 1) 6Mbps (FER ≤ 10%) -85 -82 dBm 2) 24Mbps (FER ≤ 10%) -82 -74 dBm 3) 54Mbps (FER ≤ 10%) -72 -65 9. Maximum Input Level (FER ≤ 10%) -10 dBm 10. Adjacent Channel Rejection (FER ≤8%) dB Table.3 IEEE 802.11g Mode Specification
HB-RND-xxA 7 페이지 2013-03-13 - 7 -박병만 7 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 7/13 Pages 4.4 IEEE 802.11n Mode Items Contents Specification IEEE802.11n Mode OFDM Frequency 2400 – 2483.5 MHz Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65 Mbps Target Max Output Power 17dBm DC Characteristics Min. Typ. Max. unit 1. DC current 1) Tx mode (1024byte, 20usec interval) 227 mA 2) Rx mode 80 mA Tx Characteristics Min. Typ. Max. unit 2. Power Levels 15 17 19 dBm 3. Spectrum Mask 1) Fc ± 11MHz -34 -20 dBr 2) Fc ± 20MHz -50 -28 dBr 3) Fc ± 30MHz -58 -45 dBr 4. Constellation Error (EVM) 1) MCS0 (6.5Mbps) -29 -5 dB 2) MCS4 (39Mbps) -31 -19 dB 3) MCS7 (65Mbps) -31 -28 dB 5. OBW(Occupied Bandwidth) 20 MHz 6. Center Frequency Tolerance -25 -4.5 25 ppm 7. Symbol clk freq Tolerance -25 -4.7 25 ppm 8. Outband Spurious Emissions 1) 30Mhz to 1 Ghz(BW=100kHz) tbd dBm 2) 1Ghz to 12.75 Ghz(BW=100kHz) tbd dBm 3) 1.8Ghz to 1.9 Ghz(BW=100kHz) tbd dBm 4) 5.5Ghz to 5.3 Ghz(BW=100kHz) tbd dBm Rx Characteristics Min. Typ. Max. unit 9. Minimum input Level Sensitivity 1) 6.5Mbps (FER ≤ 10%) -87 -82 dBm 2) 39Mbps (FER ≤ 10%) -79 -70 dBm 3) 62Mbps (FER ≤ 10%) -70 -64 10. Maximum Input Level (FER ≤ 10%) -20 dBm 11. Adjacent Channel Rejection (FER ≤ 8%) tbd dB Table.4 IEEE 802.11n Mode Specification
HB-RND-xxA 8 페이지 2013-03-13 - 8 -박병만 8 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 8/13 Pages 5 Antenna LGHA-WWW1301 with omni directional characteristics in the 2.4GHz band, MURATA SMD's dielectric Antenna ANCG12G44SAA145 is applied. Fig.5 ANCG12G44SAA145 Radiation Pattern 6 Electrical Characteristics Parameter min typ max Unit Operation Temperature -20 +25 +70 Deg.C Operation Humidity 0 80 % Supply Voltage 4.75 5 5.25 V Table.5 LGHA-WWW1301 Electrical Characteristics 7 User installation This manual explains to set-up the WLAN MODULE (USB DONGLE TYPE) to the Smart Pad installed in the refrigerator only. The WLAN MODULE is not available for regular laptops or any other portable devices. 7.1 USB WLAN installation requirements (1)PC(WINDOWS XP, USB1.1/USB2.0 Support) 1EA (2) Wireless AP(802.11/b/g/n) : 1EA (3) USB WLAN DONGLE XP Driver
HB-RND-xxA 9 페이지 2013-03-13 - 9 -박병만 9 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 9/13 Pages 7.2 USB WLAN DONGLE Driver installation method (1) copy the 4319USB_4.218.116.42.nvm to the “C:/WINDOWS/system32/drivers” (2) copy the driver to the proper folder of PC (3) Insert USB WLAN DONGLE to PC - Pop up “New Hardware Wizard” - Refer to below picture and click “NEXT” (4) Refer to below picture and click “NEXT”
HB-RND-xxA 10 페이지 2013-03-13 - 10 -박병만 10 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 10/13 Pages (5)Check where is the driver and click “NEXT” (6) Refer to below picture and click “Finish”
HB-RND-xxA 11 페이지 2013-03-13 - 11 -박병만 11 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 11/13 Pages (7)After installation is finished corretly, you can find out “Broadcom 802.11n Wireless USB Adapter 43xx” is activated in the network adaptor (8) Click Start Menu/Network Connection, and then select wireless device Click right button of the mouse, scan AP and connect USB WLAN DONGLE to Target AP
HB-RND-xxA 12 페이지 2013-03-13 - 12 -박병만 12 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 12/13 Pages 8 Notice WARNING The WLAN MODULE (USB DONGLE TYPE) to the Smart Pad installed in the refrigerator only. The WLAN MODULE is not available for regular laptops or any other portable devices. 8.1 FCC(Certification) FCC Notice THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED OPERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio Communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a oircuit difference from that to which the receiver is connected. - Consult the dealer of an experienced radio/TV technician for help. NOTE : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. End product labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and user. The final end product must be labeled in an visible area with the following “Contain FCC ID: BEJ-LGHAWWW1301”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met. IMPORTANT NOTE (1) Warning that this module is not approved to be operated simultaneously with other radios. Further certification requirement may required when installed and operated simultaneously with other radios. (2) Confirming of approved antenna, and advice that used other type of antenna or same type with higher gain will required additional certification.
HB-RND-xxA 13 페이지 2013-03-13 - 13 -박병만 13 페이지 2013-03-13HB-개발-xxA A4(297mmX210mm) LG ELECTRONICS 13/13 Pages 8.2 IC(Certification) This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IC Warning This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This class B digital apparatus complies with CanadianICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZEDMODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

Navigation menu