LG Electronics USA LST250 User Manual LST250 User Guide 0711
LG Electronics USA LST250 User Guide 0711
Contents
- 1. Users Manual
- 2. Users Manual per CRN 20753
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 163619 |
| Application ID | mqVSUFznvxyy2h3RsOfI3g== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 24.11kB (301344 bits) |
| Date Submitted | 2001-08-08 00:00:00 |
| Date Available | 2001-12-13 00:00:00 |
| Creation Date | 2001-08-02 12:35:09 |
| Producing Software | Acrobat PDFWriter 5.0 for Windows |
| Document Lastmod | 2001-08-07 18:17:17 |
| Document Title | LST250 User Guide_0711_.doc |
| Document Creator | Microsoft Word |
| Document Author: | melvin |
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
CDMA Fixed Wireless Terminal
User Guide
Model:
LST-250(F) & 2500(F)
FCC RF EXPOSURE INFORMATION
WARNING! Read this information before use
In August 1996 the Federal Communications Commission (FCC) of the United States
with its action in Report and Order FCC 96-326 adopted an updated safety standard
for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC
regulated transmitters. Those guidelines are consistent with the safety standard
previously set by both U.S. and international standards bodies. The design of this
phone complies with the FCC guidelines and these international standards.
To comply with FCC RF exposure requirements, a minimum separation distance of
2.7cm (1 inch) must be maintained between the user/bystander and the back of the
unit, including the antenna.
For more information about RF exposure, please visit the FCC website at www.fcc.gov
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
REVISED HISTORY
DATE
ISSUE
2001.01. 08
ISSUE 1.0
CONTENTS OF CHANGES
REMARK
Initial Release
Please read this manual before you use this product. This manual is based on the production
version of LST-250(F)/2500(F) FWT. Software changes may have occurred after this printing.
LG reserves the right to make changes in technical and product specifications without
prior notice.
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
Blank Page
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
Table of Contents
1.
Before You Start....................................................................................................6
1.1
1.2
1.3
2.
Safety Information.................................................................................................................... 6
Optimal Phone Performance ................................................................................................... 6
Care and Service ..................................................................................................................... 7
Introduction ...........................................................................................................8
2.2
3 LEDs Indicators .................................................................................................................. 10
STEP I. Check Components ............................................................................................... 10
STEP II. Place the Terminal ................................................................................................ 11
STEP III. Connect Components .......................................................................................... 11
STEP IV. Check LED indicators .......................................................................................... 11
STEP V. Install of Wall Mounting......................................................................................... 11
2.4 Installation Steps ................................................................................................................... 13
3.
Basic Operation ..................................................................................................14
3.1 Power On ............................................................................................................................... 14
3.2 Placing a call.......................................................................................................................... 14
3.3 Receiving a call...................................................................................................................... 14
3.4 Ending a call .......................................................................................................................... 14
3.5 Warning Tone after Remote Disconnect ................................................................................ 14
3.6 Dial Delay(Enblock mode only).............................................................................................. 15
3.7 Emergency Call(Enblock mode only) .................................................................................... 15
4.
System Features.................................................................................................16
4.1
4.2
4.3
4.4
4.5
5.
Hook flash .............................................................................................................................. 16
Dial Delay Time(Enblock mode only)..................................................................................... 16
ROH (Receiver Off Hook) ...................................................................................................... 16
Special Cellular Services ....................................................................................................... 16
Applications............................................................................................................................ 17
Programming ......................................................................................................18
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
Speed Dial(Enblock mode only) ............................................................................................ 18
Storing the Speed Dial Number ............................................................................................. 18
Enable or Disable Speed Dial................................................................................................ 19
Operation ............................................................................................................................... 19
Emergency Call(Enblock mode only) .................................................................................... 19
Entering the emergency phone number ................................................................................ 19
Enable or Disable emergency call ......................................................................................... 19
Hot Line(Enblock mode only)................................................................................................. 19
Programming the Hot Line number........................................................................................ 19
Enable the Hot Line Feature.................................................................................................. 20
Disable the Hot Line Feature ................................................................................................. 20
Programming the Hot Line Time............................................................................................ 20
Alarm(Enblock mode only)..................................................................................................... 20
Entering Alarm Time (12-hour Mode) .................................................................................... 20
Entering Alarm Time (24-hour Mode) .................................................................................... 20
Disable Alarm Feature ........................................................................................................... 21
Volume Level ......................................................................................................................... 21
Changing the Volume Level................................................................................................... 21
Outgoing Call Lock(Enblock mode only) ............................................................................... 21
Enable or Disable Outgoing Call Lock ................................................................................... 21
Changing Outgoing LOCK Code ........................................................................................... 21
G3 FAX Mode Setting ............................................................................................................ 22
Enable or Disable G3 FAX mode........................................................................................... 22
Restrict Call Mode Setting ..................................................................................................... 23
Set Restrict Call Level ........................................................................................................... 23
Storing the Permit Dial Number ............................................................................................. 23
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
Storing the Deny Dial Number(Restricted dial number) ........................................................ 24
6. Troubleshooting ..................................................................................................25
7. General Information ............................................................................................26
7.1
7.2
LST-250(F)............................................................................................................................. 26
LST-2500(F)........................................................................................................................... 27
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
1. Before You Start
1.1
Safety Information
Warning
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
Do not use this product near swimming pools or other bodies of water.
IMPORTANT
Before installing or operating this product, read this information..
1.2
Optimal Phone Performance
Do not operate your product when holding the antenna, or when someone is within four
inches (ten centimeters) of the antenna. Holding the antenna affects call quality and may
cause the telephone to operate at a higher power level than needed.
For the best call quality, keep the antenna free from obstructions and point the antenna
straight up.
Do not use the unit with a damaged antenna. Have your antenna replaced by a qualified
technician immediately. Use only a manufacturer-approved antenna. Non-approved
antennas, modifications, or attachments could impair call quality, damage the phone.
RF energy may affect improperly installed or inadequately shielded personal medical
devices such as pace markers, hospital monitor. Consult the manufacturer of any personal
medical devices to determine if they are adequately shielded from external RF energy.
Turn your terminal OFF in health care facilities when any regulations posted in the areas
instruct you to do so. Hospitals or health care facilities may be using equipment that could
be sensitive to external RF energy.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the radio or television and the telephone.
- Connect the equipment into an outlet on a circuit different from that to which the
terminal is connected.
- Consult you Authorized LG Dealer of an experienced radio/TV technician for help.
Use only the battery, antenna and AC power supply provided by LG. Using any other type
will invalidate the warranty.
Only authorized personnel should service the phone and its accessories. Faulty
installation or service any be dangerous and may invalidate the warranty.
Do not use the unit in designated “no cellular phone use” area.
Avoid exposure to high temperature or humidity.
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
Avoid wetting the unit with any liquids. If the unit gets wet, turn the power off immediately
and remove the backup battery and AC power supply. If the unit is inoperable, then return
to the service agent for service.
Avoid shock or impact.
We recommend you to charge the backup battery before initial use. Backup battery may
be discharged during delivery.
1.3
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may
cause undesired operation.
Care and Service
Unplug the Telephone from the wall outlet and remove antenna (or disconnect antenna
cable) before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
If the unit fails for any reason, do not attempt to disassemble; contact the telephone
service provider for assistance.
If any of the following conditions exist: Unplug the unit at the wall plug, remove battery,
and call the service provider.
- The power supply cord is damaged or frayed.
- Liquid has been spilled into the unit.
- The unit has been exposed to rain or water.
- The unit has been dropped or damaged.
- The unit does not work normally by following the operating instructions.
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
2. Introduction
Congratulations on your purchase of the LG Fixed Wireless Terminal that has been designed to
operate on the latest digital mobile communications technology, Code Division Multiple Access
(CDMA). This CDMA digital technology has greatly enhanced voice clarity and can provide
various advanced features. The terminal enables the normal operation and direct connection of
standard telephone equipment into the cellular network.
The standard unit provides:
l Dial tone;
l Touch tone (DTMF) or Pulse Dialing;
l Support Caller ID Telephone;
l Voice-Mail Notification ring-alerts you to new voice-mail messages;
l Ring voltage used to ring the telephone connected to the unit, with a Ringer Equivalence
Number of 4;
l A phone jack to plug in the telephone equipment (RJ-11 Port);
l A phone jack to plug in the G3 FAX equipment (RJ-11 Port);
l DB9 Data Port for service and repair
l AC Power supply with barrel plug connector;
l Three lights (LEDs) to indicate the status of the unit;
l Dipole Antenna;
The LG Fixed Wireless Terminal can operate differently according to the system provider
in the dialing manner. The first one is the “Enblock” mode and the second one is the
“Overlap” mode. Please contact your service provider in which mode the LG Fixed
Wireless Terminal is working.
Some features can not be supported by service provider’s policy and dialing method.
For instance, the following features may not be supported in Overlap dialing mode;
- Dial Delay and Dial Delay Time
- Speed Dial
- Emergency Call
- Hot Line Call
- Alarm
- Outgoing Call Lock
Other features as determined by your service provider.
Note: Telephones with multiple terminating impedance should be set for 600ohms.
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
2.1 Front View of the Terminal
< Figure 1 >
ITEM
DESCRIPTION
LEDs
Indicate the status of the unit
DC-12V
AC Power Adapter
FAX (RJ-11 Jack)
Connecting Port for G3 FAX Machine
Phone (RJ-11 Jack)
Connecting Port for Single Line Telephone
RS-232C DB 9 Connector
Connecting Port for Data Service to PC
TNC Antenna Connector
Connecting Port for TNC Antenna
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
2.2
3 LEDs Indicators
LED
COLOR
GREEN-solid
POWER LED
SIGNAL LED
ORANGE-solid
DC Power is applied
Battery Power is applied
RED-solid
Low Battery
GREEN-solid
Good Signal
ORANGE-solid
Poor Signal
RED-solid
MODE LED
Operating Condition
GREEN – blink
(0.5sec On / 0.5sec Off)
GREEN – blink
(1 sec On / 1 sec Off)
GREEN-solid
No Service Area
Voice Message is received
Data Service or G3 Fax Service is working
G3 FAX receive mode is enabled
2.3 Installation
You should follow each step carefully as shown below in order to guarantee proper operation of
CDMA Fixed Wireless Telephone.
STEP I.
Check Components
Fixed Wireless Terminal is supplied with the following standard unit and accessories;
1. LST-250(F)/2500(F) Main Unit
-1 EA2. Dipole Antenna
-1 EA3. Backup Battery
-1 EA4. User Guide
-1 EA5. AC/DC Power Adapter
-1 EA6. Power Cord
-1 EA-
Please make sure that these components are present and check for evidence of shipping
before you begin the unit installation. If components are missing or damage is found, contact
your authorized LG distributor immediately.
10
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
STEP II.
Place the Terminal
Place the terminal on the stable flat secure surface area (desk, table, etc.). Avoid direct
exposure to the sun lights and damp area.
Read the Safety Information located at the first part of this document before you place the
terminal.
STEP III.
Connect Components
Connect the antenna to the TNC connector located at the topside of the terminal. (See
Figure 1 to locate the TNC connector.) If you placed the terminal on the flat surface, bend
the antenna up right.
Connect your phone cord to the RJ-11C port located at the left side of the terminal.
Connect the battery cable to the DC battery connector at the back of the main unit.
-. Remove the battery compartment cover.
-. Connect battery to the connector.
-. Replace the battery cover.
Connect the AC power supply cable to the DC input port located at the right side of the
terminal.
If you use Data Service or PC FAX Service, connect your RS-232C cable cord to the DB9
port located at the right side of the terminal.
If you use G3 FAX machine, connect your line cord of G3 FAX to the RJ-11 port located at
the right side of the phone port.
“ Refer to Connection Diagram with external equipment in Figure 2 “
STEP IV.
Check LED indicators
When you followed the installation instruction STEP I to STEP III, please check the LEDs for
normal operation. When DC power is fed at the first time, LEDs will operate as
follows:
1. After few seconds, if receiving signal strength is strong enough, then SIGNAL LED is
GREEN, if not, it is ORANGE or RED. And MODE LED is turned off. Power LED is
GREEN if AC/DC power is applied.
STEP V.
Install of Wall Mounting
To mount terminal on the wall, please follow the procedure to install it correctly.
1. Determine suitable location to mount terminal with mounting template;
2. Mark the two openings and select round or panhead type screw;
3. Drill out the holes with drill bit smaller in diameter than the screws
4. Secure two screws into the wall, leaving about 1/8inch gap between the screw heads
and the wall;
5. Insert the DC power pack into an electrical outlet and attach the telephone line into the
Phone Jack (RJ-11) of the unit.
6. Place the terminal over the two screws so that the screw head protrudes out of the
opening;
7. Slide the terminal downward until the screw head is locked at the top of the opening and
the terminal is secure;
8. Tighten the screws the terminal is resting upon;
11
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
RJ-11
RJ-11
PC
TELEPHONE
G3 Analog Fax
[LST-250F]
* Note :
- G3 Fax can not connected to your LST-250 terminal.
- Length between LST-250(F) and Telephone : over 1m.
The adapter type(with power cord) may be different by country adaptation.
12
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
RJ-11
RJ-11
PC
TELEPHONE
G3 Analog Fax
[LST-2500F]
* Note :
- G3 Fax can not connected to your LST-2500 terminal.
- Length between LST-2500(F) and Telephone : over 1m.
< Figure 2. Connection Diagram with External Equipment >
2.4 Installation Steps
Please follow the below procedure to install the unit properly.
Connect the
antenna to the
Bend the
antenna up right.
TNC connector
(Turn right).
Connect your phone
Connect the AC
Cord.
power supply.
13
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
3. Basic Operation
3.1
Power On
1. The POWER LED indicates the presents status;
1)
Using AC Adapter : Solid Green
2)
Using internal battery : Solid ORANGE
3)
Using internal battery and battery is week : Solid Red
2.
If the radio service is not available or radio signal is too weak to detect;
The SIGNAL LED is Red. (No Service status)
3. When the phone is succeeded in getting the service, SIGNAL LED indicates the strength
of the signal.
1)
Lifting handset, dial tone is heard and you can enter a phone number.
(Not entering any key for 15 seconds (In the overlap dial mode, it may take over 15
seconds.) warning tone will be produced)
*) If Hot Line function is enabled, busy tone is not produced and hot line number is
automatically connected.
*) While having maintenance request order or lock order from the main system, neither dial
tone nor busy tone is produced. Instead of them, the lock tone(“pi-pi-pi”) will be heard
one time and there will be no sound and both of MODE LED and POWER LED will be
blinking with GREEN color simultaneously.
3.2
Placing a call
When lifting handset of the connected phone ("off hook"), the terminal determines whether
cellular service is available. If it is available, dial tone is produced and a number can be dialed
normally. If phone service is not available, SIGNAL LED of the terminal will be red and no dial
tone will be heard.
3.3
Receiving a call
The connected telephone rings when an incoming call is detected. Pick up the handset and
begin talking.
3.4
Ending a call
When you have completed the call, place the handset back on hook. Also you can hook flash
more than about 1 second to end a call and place a new call without hanging up the handset.
3.5
Warning Tone after Remote Disconnect
A warning tone may be heard in the telephone after a remote party hangs up from a call,
allowing another call to be initiated after hook-flash.
14
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
3.6
Dial Delay(Enblock mode only)
The terminal waits 5 seconds before transmitting the dialed telephone number into the cellular
network.
3.7
Emergency Call(Enblock mode only)
When emergency call number is connected once, it will not be terminated unless the called party
disconnects the call(Emergency Call Hold Service). Therefore even caller hangs up the phone,
the line will be still connected, so if the caller picks up the phone again, he can continue talking.
If emergency call is connected, cellular service is not supported.
As long as your telephone is registered on a system, you can place a call to emergency number
including 911-even if your telephone is locked* or restricted*.
Please check the available emergency call number with your service provider.
*) “Transmit Lock” or “Transmit Restrict” features have a meaning only in “Enblock” mode.
15
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
4. System Features
4.1
Hook flash
When the terminal receives a hook-flash from the connected telephone device, it will
automatically allow:
1.
For producing dial tone again after a phone number has been dialed without connection.
2.
The use of special cellular services which may be available in your cellular service area.
Note:
4.2
Hook-flash is accomplished in a call through either pressing the dedicated hook-flash
key which is available on some phones or through a rapid single press of the hang-up
mechanism upon which the handset rests when the phone is hung up.
Dial Delay Time(Enblock mode only)
When placing a call, the phone number is sent over the network after last digit is dialed. In order
to insure adequate time for dialing the last digit, a delay of 5 seconds is programmed into the
terminal.
4.3
ROH (Receiver Off Hook)
If the telephone equipment remains “off-hook”, meaning that the handset is left off of its cradle as
it would be when you hang up, with no dialing activity for about 45 seconds, a ROH tone emits
from the receiver for a period of 60 seconds.(In the overlap dial mode, above “45 seconds” or
“60 seconds” may be different according to the system.)
( This feature may be available or not by country specification.)
4.4 Special Cellular Services
Many cellular systems offer special services such as call waiting, call forwarding, etc. You can
purchase these services from your cellular service provider. There are certain dialing sequences
to be entered, which vary from service provider to service provider. The service provider will
provide the dialing instructions for your system.
Call Forwarding – An incoming call can be delivered to another telephone number programmed.
Please contact your cellular service provider to use this feature.
Call Waiting – You can receive another incoming call during a call. In this case, you will hear
beep tone and then you can connect the second call holding the first call by entering a code
required by cellular service provider. Your cellular service provider may require hook-flash (a
quick, simulated "hang up") to answer the waiting call. Other providers may require entering the
codes involving digits 1-9, *, and # to answer a waiting call.
Three-way Conference Calls - For three-way conference calls, a hook-flash transmits the
SEND command. Please contact your cellular service provider for more information on using this
service.
16
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
F Example
Dial the first number and wait until connected;
When connected, give hook-flash and dial the second number and give one more hook-flash to be
connected;
When the second call is connected, give hook flash to complete a 3-way conference call.
Voice Mail – Use voice mail service in the same manner as you would on a regular telephone. If
you have a new voice-mail message, the WLL-terminal transmits a special Voice-Mail
Notification Ring (1sec On / 6sec Off default) and Mode LED is blinking (0.5sec On/0.5sec Off).
Please contact your cellular service provider for more information on using Voice Mail or to
change Voice-Mail Ring pattern.
Caller ID – LST-250(F)/2500(F) can support Caller ID service if you have a telephone with Caller
ID feature. Please contact your cellular service provider for more information on using this
service.
4.5
Applications
Data Communication - LST-250(F)/2500(F) is capable of transmitting and receiving IS-707 Fax
or modem communications. For data communications, you will need a data communication kit
and a PC Fax software diskette where needed. For further information, please contact our
authorized service dealer.
Multi-extension Installations - For a multi-extension installation, make sure that all the
extensions are on-hook. If one extension is off-hook (not hung up), none of the extensions on
that line will ring when a call is being received.
17
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
5. Programming
LST-250(F)/2500(F) provides various convenient and various features to user. This chapter
describes how to program these features and to use them. The followings are main features can
be used;
Speed Dial(Enblock mode only)
Emergency Call(Enblock mode only)
Hot Line Call(Enblock mode only)
Wake-up Alarm(Enblock mode only)
Conversation Voice Level
Outgoing Call Lock(Enblock mode only)
G3 Fax receive
Restrict Call
1.
2.
3.
4.
5.
Programming Instruction
Lift Handset and press “#” key twice and you will hear the Menu Entering tone.
Enter the field number (1 ~ 8).
Press “#” key and you will hear confirmation tone.
Enter sub-fields and their options.
Press “*” key to save and you will hear confirmation tone.
Note :
- As to the characteristic quality of some telephones, confirm tone or error tone could
not be heard.
5.1
Speed Dial(Enblock mode only)
LST-250(F)/2500(F) has 30 memory locations (1~30:1 or 2 digits) to store frequently used phone
numbers and you can make a call by pressing memory location number only when the speed
dial feature is enabled.
Storing the Speed Dial Number
1.
Press “#” + “#” + “1” continuously to enter speed dial programming mode.
2.
Press “#” and one of memory numbers (1~30).
3.
Press “#” and the phone number (Max. 32 digits).
4.
Press “*” to store.
18
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
Enable or Disable Speed Dial
1.
Press “#” + “#” + “1” continuously to enter speed dial programming mode.
2.
Press “#” and “1” or “2” to enable or disable respectively.
“1” – Speed Dial Enable
“2” – Speed Dial Disable
3.
Press “*” to store.
Operation
1.
Make a speed dial function enable.
2.
Lift handset and dial tone will be heard.
3.
Press speed dial number and wait for dial timeout(5 seconds).
5.2
Emergency Call(Enblock mode only)
LST-250(F)/2500(F) has 3 emergency call numbers (1~3) and max. 32 digits can be stored in
each emergency call number.
Entering the emergency phone number
1.
Press “#”+”#”+”2” continuously to enter emergency call programming mode.
2.
Press “#” and one of the emergency memory location numbers (1~3).
3.
Press “#” and the phone number (Max. 32 digits).
4.
Press “*” to save and enable this function.
Enable or Disable emergency call
1.
Press “#”+”#”+”2” continuously to enter emergency call programming mode.
2.
Press “#” and Enable code (“1”) or Disable code (“2”).
3.
Press “*” to save.
If Emergency Call is disabled and Emergency Call number has been already programmed,
you can make enable Emergency Call by pressing “#’+”#”+”2”+”#” + ”1”+”*” without
entering a emergency call number again.
5.3
Hot Line(Enblock mode only)
While the Hot line function is enabled, the programmed number will be automatically dialed
when you pick up the handset and wait for the programmed hot line time (2~10sec) without any
key press.
Programming the Hot Line number
1.
Press “#”+”#”+”3” continuously to enter Hot Line programming mode.
2.
Press “#” and Hot Line Enable code “1”.
19
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
3.
Press “#” and Hot Line phone number (Max. 32 digits).
4.
Press “*” to save and enable this function.
Enable the Hot Line Feature
1.
Press “#”+”#”+”3” continuously to enter Hot Line programming mode.
2.
Press “#” and Hot Line Enable code “1”.
3.
Press “*” to save.
Disable the Hot Line Feature
1.
Press “#”+”#”+”3” continuously to enter Hot Line programming mode.
2.
Press “#” and Hot Line Disable code “2”.
3.
Press “*” to save.
Programming the Hot Line Time
1.
Press “#”+”#”+”3” continuously to enter Hot Line programming mode.
2.
Press “#” and Hot Line time code “3”.
3.
Press “#” and enter desired Hot Line time (2~10 seconds).
4.
Press “*” to save.
If Hot Line is disabled and Hot Line number has been already programmed, you can make
enable Hot Line feature by pressing “#’+”#”+”3”+”#”+”1”+”*” without entering a Hot Line
Number again.
5.4
Alarm(Enblock mode only)
If alarm feature is enabled, you will hear ring at the programmed alarm time every day for 3
minutes.
Alarm does not ring on the state of hook off, conversation or no service.
Entering Alarm Time (12-hour Mode)
1.
Press “#”+”#”+”4” continuously to enter alarm time programming mode.
2.
Press “#” and alarm time code “1” for 12-hour mode.
3.
Press “#” and alarm time (HHMM +am(“1”) / pm(“2”)).
4.
In the forenoon, time range is 0000~1159.
5.
In the afternoon, time range is 1200~1259 or 0100 ~1159.
6.
Press “*” to save and enable Alarm Time.
Entering Alarm Time (24-hour Mode)
1.
Press “#”+”#”+”4” continuously to enter alarm time programming mode.
2.
Press “#” and alarm time code “2” for 24-hour mode.
3.
Press “#” and alarm time (HHMM). (0000~2359)
20
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
4.
Press “*” to save and enable Alarm Time.
Disable Alarm Feature
1.
Press “#”+”#”+”4” continuously to enter alarm time programming mode.
2.
Press “#” and alarm disable code “2”.
3.
Press “*” to save.
If Alarm is disabled and time has been already programmed, you can make enable Alarm
feature by pressing “#’+”#”+”4”+”#”+”1”+”*” without entering alarm time again.
5.5
Volume Level
There are three voice volume levels to be controlled by software, and you can set the level to the
adequate conversation volume.
Changing the Volume Level
1.
Press “#”+”#”+”5” continuously to enter Volume Level programming mode.
2.
Press “#” and Volume Level (1~3),.
“1” – LOW Level
“2” – MIDDLE Level
“3” – HIGH Level
3.
Press “*” to save.
Before pressing “*”, you can enter volume level continuously.
5.6
Outgoing Call Lock(Enblock mode only)
If you try to make an outgoing call while outgoing call lock is enabled, then you will hear warning
tone after dial time-out as a indication of entering the LOCK code. You should enter LOCK code
to make an outgoing call. LOCK code is composed of 4 digits and the initial setting is “0000”.
Outgoing Call Lock feature is disabled as a factory setting.
Enable or Disable Outgoing Call Lock
1.
Press “#”+”#”+”6”+ continuously to enter Outgoing Call Lock programming mode
2.
Press “#” and “LOCK code (4 digits)”
3.
Press “#” and Enable (“1”) or Disable (“2”) code.
4.
Press “*” to save.
Changing Outgoing LOCK Code
1.
Press “#”+”#”+”6”+ continuously to enter Outgoing Call Lock programming mode
2.
Press “#” and “LOCK code (4 digits)”
3.
Press “#” and “3” to change LOCK code.
4.
Press “#” and “new LOCK code (4 digits)”.
21
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
5.
Press “#” and re-enter “new LOCK code (4 digits)”.
6.
Press “*” to save.
5.7 G3 FAX Mode Setting
To activate a Data Fax call by G3 FAX connected to your LST-250F/2500F terminal from the
other devices (Land or Mobile Data Fax), your service provider should support wireless data
FAX. And the LST-250F/2500F mode should be changed to G3 FAX mode to change data path
from RS-232C to G3 FAX machine. Because the terminal doesn’t recognize the call is for FAX or
voice before being response. Following is the procedure to change data path and default data
path is RS-232C data path.
Once G3 Fax mode is set, if AC power is gone and turned on again, the saved G3 Fax mode
value is restored.
Enable or Disable G3 FAX mode
1.
Press “#”+”#”+”7” continuously to enter G3 FAX programming mode.
2.
Press “#” and Enable (“1”) or Disable (“2”) code.
Enable means that Data call path is changed to G3 FAX.
Disable means that Data call path is changed to RS-232C. (Default mode)
3.
Press “*” to save.
Note 1. How to setup G3 FAX mode more easily
1. Press “#”+”#”+”7” continuously to enter G3 FAX programming mode.
2. Press Enable (“1”) or Disable (“2”) code.
Enable means that Data call path is changed to G3 FAX.
Disable means that Data call path is changed to RS-232C. (Default mode)
Note 2. Sending or receiving some documents by G3 FAX is possible only in AC power mode. If
AC power is gone, you cannot use the G3 Fax machine connected to the LST250F/2500F.
Note 3. The recommended usage for this G3 Fax Mode is like this;
1. Disable G3 Fax Mode for normal usage.
You can make a voice call using the telephone device connected to the “Tel/Fax”
jack of the LST-250F/2500F.
You can fax a document using the G3 Fax machine connected to the “Tel/Fax”
jack of the LST-250F/2500F.
2. To receive or send a document by fax, should be set G3 Fax Mode. After receiving
22
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
the fax document, disable G3 Fax Mode for another voice call.
3. If you want to use the LST-250F/2500F terminal only for G3 Fax sending or receiving
other than the voice call, then keep the terminal in G3 Fax Mode enabled state.
5.8 Restrict Call Mode Setting
While the Restrict Call function is enabled, the specified numbers cannot be called. These
specified numbers start with specific digits. The specific digits are set according to the following
procedure (Storing the Deny dial number).
Among these specified numbers you can permit some numbers by designating start digits by
following procedure (Storing the Permit dial number).
LST-250(F)/2500(F) has 10 Deny dial numbers (1~10) and max. 32 digits can be stored in each
Deny dial number.
LST-250(F)/2500(F) has 10 Permit dial number (1~10) and max. 32 digits can be stored in each
Permit dial number.
If you set Emergency call, the emergency number is not applied to this restrict call.
Set Restrict Call Level
1.
Press “#”+”#”+”8”+ continuously to enter Restrict Call programming mode.
2.
Press “#” and “LOCK code” (4 digits : set in Outgoing call lock / default is 0000).
3.
Press “#” and restrict level (1~4)
“0” – No restriction
“1” – restriction
“2” – Emergency only (All excepting emergency are restricted.)
4.
Press “*” to save
Storing the Permit Dial Number
1.
Press “#”+”#”+”8”+ continuously to enter Restrict Call programming mode.
2.
Press “#” and “LOCK code” (4 digits : set in Outgoing call lock / default is 0000).
3.
Press “#” and “1” to enter Permit Dial Number store step.
4.
Press “#” and one of “Memory number” for permit dial number(1~10).
5.
Press “#” and the “digits” (Max. 32digits).
6.
If you want to store more Permit Dial Numbers continue from step3
If you want to finish at this point, Press “*” to save.
23
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
Storing the Deny Dial Number(Restricted dial number)
1.
Press “#”+”#”+”8”+ continuously to enter Restrict Call programming mode.
2.
Press “#” and “LOCK code” (4 digits : set in Outgoing call lock / default is 0000).
3.
Press “#” and “1” to enter Deny Dial Number store step.
4.
Press “#” and one of “Memory number” for deny dial number(1~10).
5.
Press “#” and the “digits” (Max. 32digits).
6.
If you want to store more Deny Dial Numbers continue from step3
If you want to finish at this point, Press “*” to save.
24
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
6. Troubleshooting
In the event you are unable to place or receive telephone calls, first check the appropriate power
indication on the LED. In case of no power, check the wiring connections between the power
outlet and the terminal. Check for the appropriate service indication on the LED. If an adequate
signal is not present, try different locations for the better signal reception.
This will verify the condition of the telephone equipment and the internal wiring of the telephone
service to verity that it is working properly. If the telephone system of wiring is not working
properly, replace or repair the equipment as required. The unit will not function with equipment
that requires data transmission.
Contact your service provider if either of the following condition is true:
The terminal does not work and the LED indicates “No Service” and if changing the
locations does not resolve the problem.
The terminal does not work and the LED indicates “In Service”.
Power Supply – If the unit does not respond once plugged into a power supply;
²
Check that the AC power source.
²
Check that the Barrel Plug of the Power Supply is properly inserted into the
terminal.
²
Check that the terminal Power Supply is properly plugged into the electrical outlet
or power source.
Warning! Only Authorized Service Personnel should remove the cover of the fixed
wireless terminal for additional service. The contents of the terminal contain components
that present an Electric Shock Hazard if handled improperly.
For further assistance, contact your Authorized LG Distributor for service and
assistance. Please keep your Model number and Serial number ready for quicker
service.
25
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
7. General Information
7.1 LST-250(F)
Main Unit
Item
Description
Tx Frequency
Digital : 824 ~ 849 MHz
Rx Frequency
Digital : 869 ~ 894 MHz
Channel Bandwidth
1.25 MHz
Frequency Stability
Digital :
Tx Power
Digital : Max. 0.2W
Rx Power Level
-104 ~ -25 dBm
Size
210 x 147 x 63 mm
Weight(g)
610g ( w/o battery ) / 800g ( w/ battery )
300 Hz
AC/DC Adapter
Item
Description
Input Voltage
100V ~ 250V AC
Input Current
0.6A
Input Frequency
50 / 60 Hz
Output Voltage
12V(DC) / 2A
Internal Back-up Battery
Item
Description
Capacity
8.4V NiMH
Talk duration time
2 Hours
Standby duration time
24 Hours
Charging duration time
Trickle, 24 Hours
26
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
7.2
LST-2500(F)
Main Unit
Item
Description
Tx Frequency
Digital : 1850 ~ 1910 MHz
Rx Frequency
Digital : 1930 ~ 1990 MHz
Channel Bandwidth
1.25 MHz
Frequency Stability
Digital :
Tx Power
Digital : Max. 0.2W
Rx Power Level
-104 ~ -25 dBm
Size
210 x 147 x 63 mm
Weight(g)
610g ( w/o battery ) / 800g ( w/ battery )
150 Hz
AC/DC Adapter
Item
Description
Input Voltage
100V ~ 250V AC
Input Current
0.6A
Input Frequency
50 / 60 Hz
Output Voltage
12V(DC) / 2A
Internal Back-up Battery(A)
Item
Description
Capacity
8.4V NiMH
Talk duration time
2 Hours
Standby duration time
24 Hours
Charging duration time
Trickle, 24 Hours
Internal Back-up Battery(B)
Item
Description
Capacity
8.4V NiMH
Talk duration time
1 Hour
Standby duration time
12 Hours
Charging duration time
Trickle, 24 Hours
27
LG CDMA Fixed Wireless Terminal
LST-250(F)/2500(F)
Licensed by QUALCOMM Incorporated under one or more of the following Patents:
U.S, Patent No. 4,901,307 U.S, Patent No. 5,056,109 U.S, Patent No. 5,099,204
U.S, Patent No. 5,101,501 U.S, Patent No. 5,103,459 U.S, Patent No. 5,107,225
28
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2001:08:02 12:35:09Z Modify Date : 2001:08:07 18:17:17-03:00 Page Count : 29 Creation Date : 2001:08:02 12:35:09Z Author : melvin Producer : Acrobat PDFWriter 5.0 for Windows Mod Date : 2001:08:07 18:17:17-03:00 Metadata Date : 2001:08:07 18:17:17-03:00 Title : LST250 User Guide_0711_.doc Creator : melvinEXIF Metadata provided by EXIF.tools