LG Electronics USA LTGEN97LG Cellular/PCS GSM/EDGE Transceiver with Bluetooth User Manual

LG Electronics USA Cellular/PCS GSM/EDGE Transceiver with Bluetooth Users Manual

Users Manual

LG Telematics Test Manual [TG97AABJU] Version 1.0 2011.04.15
LG Telematics Revision History Author Description Date Jongman Park Merged document. Document start April 15, 2011
LG Telematics Contents 1. How to Place a Call 2. ATT Tool for TCU Setting 3. VCP Commander FCC Information
LG Telematics 1. How to Place a Call Fig.1
LG Telematics
LG Telematics 2. ATT Tool for TCU Setting 1) Set COM Port Fig.2 2) Check Connection Status
LG Telematics Fig.3 3) NAD Screen Fig.4
LG Telematics 4) Select Forced band mode and apply it Fig.5 - Click to see the selectable menu for changing - After select the Service mode, click “Control” to apply it.
LG Telematics Fig.6 4) Check result of change. Fig.7
LG Telematics 3. VCP Commander 1) Run “VCP-Commander.exe”. This tool is single executable file. 2) Connect the named “CAIT”-port to Your PC’s serial port. 3) Check the serial baud rate of VCP (Power-up default is 38400bps) 4) select your PC’s COM-port, Press “Connect button” 5) Test the right connection. Press “END”, verify that “Status” is Flipped (“Cmd FAIL” to “Cmd OK”) 6) Select command from drop-down-list And enter “Value 1” or “Value 2” according to each command. 7) Press “SET” button, then status is flipped. 8) Below table are command lists, value 1 and value 2. “Command” “Value 1” “Value 2” Description PREF_AUTOMATIC PREF_CELL_ONLY PREF_PCS_ONLY PREF_CDMA_ONLY PREF_ANALOG_ONLY PREF_HOME_ONLY Don’t care Don’t care Set system selection mode PREF_P_REV_3 PREF_P_REV_4 PREF_P_REV_6 Don’t care Don’t care Set MOB_P_REV temporally A_KEY See example 1 See example 1 Set A-key value
LG Telematics PREF_FOR_RC 1 ~5 Don’t care Set NV_PREF_FOR_RC_I IMSI_MCC 3-digit Decimal ie’ “120” Don’t care Set NV_IMSI_MCC_I IMSI_11_12 2-digit Decimal ie’ “12” Don’t care Set NV_IMSI_11_12_I (MNC) SCM One-byte decimal Don’t care Set NV_SCM_I SLOT_SYCLE_INDEX 0 ~ 7 Don’t care Set NV_SLOT_CYCLE_INDEX_I MOB_TERM_HOME 0 or 1 Don’t care Enable(1) or Disable(0) MOB_TERM_FOR_SID 0 or 1 Don’t care Enable(1) or Disable(0) MOB_TERM_FOR_NID 0 or 1 Don’t care Enable(1) or Disable(0) Dial_SO2_LB, Dial_SO3_EVRC, Dial_SO9_LB13, Dial_SO54 Dial_SO55_LB Dial_SO32768 Dial_SO32798 Dial_SO32799 Don’t care Don’t care Originate call with specified SO. Dial number is fixed to “111” internally. CALL_ANSWER Don’t care Don’t care Answer incoming call CALL_END Don’t care Don’t care End call. Power_Down Don’t care Don’t care Force power-down “Communication Module” only After this command, must do unplug then plug main VCP power to power-up Module. Power_Recycle Don’t care Don’t care Force power-recycle “Communication Module” only
LG Telematics FCC Information FCC part 15.19 This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) this device ma not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Installation This unit should only be installed by qualified personnel by GMOnstar. Address P.O.Box 430627 Pontiac, MI 48343
Part 15.21 statement "Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. “ "In order to comply with RF Exposure requirements the antenna or radiating element of this device must be installed to ensure that it is at least 20cm from end users. The antenna supplied with this device must not exceed a maximum gain of 9.74dBi in the cellular band and 8.25dBi in the PCS band." Part 15.105 statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Part 15 Class B Compliance This device and its accessories comply with part15 of FCC rules. Operation is subject to the following two conditions:

Navigation menu