| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1128097 |
| Application ID | /RHieG+YZHk7NchOyWnQ6A== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 62.85kB (785579 bits) |
| Date Submitted | 2009-06-23 00:00:00 |
| Date Available | 2009-12-20 00:00:00 |
| Creation Date | 2009-06-05 04:09:49 |
| Producing Software | Acrobat Distiller 8.1.0 (Windows) |
| Document Lastmod | 2009-06-23 14:12:48 |
| Document Title | Microsoft Word - M13 User Manual.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | ddilboy |
M13 Device description
Version 0.1 – APR 7th 2009
Part 15.21 statement
" Change or Modifications that are not expressly approved by the manufacturer could void
the user's authority to operate the equipment. “
Part 15.105 statement
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Part 15 Class B Compliance
This device and its accessories comply with part15 of FCC rules.
Operation is subject to the following two conditions:
(1) This device & its accessories may not cause harmful interference.
(2) This device & its accessories must accept any interference received,
including interference that may cause undesired operation.
1.1 Feature
Copyright
Copyright © 2009 LG Electronics Inc. All Rights Reserved.
Though every care has been taken to ensure the accuracy of this document, LG Electronics Inc. cannot
accept responsibility for any errors or omissions or for any loss occurred to any person, whether legal or
natural, from acting, or refraining from action, as a result of the information contained herein.
Information in this document is subject to change at any time without obligation to notify any person of
such changes.
LG Electronics Inc. may have patents or patent pending applications, trademarks copyrights or other
intellectual property rights covering subject matter in this document. The furnishing of this document
does not give the recipient or reader any license to these patents, trademarks copyrights or other
intellectual property rights.
No part of this document may be communicated, distributed, reproduced or transmitted in any form or
by any means, electronic or mechanical or otherwise, for any purpose, without the prior written
permission of LG Electronics Inc.
The document is subject to revision without further notice.
All brand names and product names mentioned in this document are trademarks or registered
trademarks of their respective owners.
1.1. Feature
Caution
To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm (8
inches) between the equipment and the body must be maintained.
M13
At least 20 cm (8 inches)
1.1. Feature
About This Document
Revision History
Version
Date
0.1
2009-04-07
References
Comment
Initial Draft
Author
Sang Ha Park
1.1. Feature
General Description
1.1 Feature
1.1
Feature
This document describes briefly the board level operations, key features and the
environment of the M13 Platform. The purpose of this platform is the verification of
LG LTE ASIC, namely ‘L1000’, and the evaluation of LG UE system performance. The
further details about the characteristics and functions of L1000 are available on other
documents. M13 consists of a CDMA main board, a LTE sub board.
Specification
LTE only
SW Date
31-May-30
HW
General
Interface Spec.
LTE
USB 2.0 High Speed
CDMA
USB 2.0 Full Speed
External port
Standard(SW ver.)
Band support
Main chipset
Max. Data rate
Transmitter
Remark
Micro USB 1 Port
LTE
3GPP Rel. 8 (Dec. 2008)
CDMA
N/A
LTE
3GPP Band 13
(700 MHz Upper C block)
CDMA
N/A
LTE
L1000 (by LGE)
CDMA
MSM6800A (by QCT)
LTE
DL 50Mbps / UL 25Mbps
(Category2)
CDMA
N/A
GPS
Not Support
Battery
Support
Tx Diversity
LTE
Not support
Max. Tx Power
LTE
23 dBm
Band Width
LTE
10MHz
UE Antenna
Selection will not
be supported
At antenna port
1.1. Feature
Receiver
SW
Interface
Modulation Method
LTE
Up to 16QAM
Rx Diversity
LTE
Support
MIMO
LTE
2x2 MIMO
Band width
LTE
10MHz
Modulation Method
LTE
Up to 64QAM
Interface protocol
LTE
USB Ethernet
CDMA
N/A
LTE
3 Ports (Data, DM, Control)
CDMA
3 Ports (Data, DM, Control)
USB Driver
System
selection
Downloading Tool
Support
Downloading tool
for field upgrade
through USB port
DM (Diagnostic Monitor)
Support
LGE tool for LTE
Prefered system selection
Support 'LTE only' mode
LTE only'
'LTE preferred'
'eHRPD only'
Support System
LTE only
PRL/PLMN List
Authentication User Identity Module
(IMSI)
Identity
Authentication
LTE
Support PLMN
CDMA
N/A
LTE
Device
CDMA
N/A
LTE
Not Support
CDMA
N/A
Numbering & Identities
IP support
Adaptive
switching
between downlink
Transmit Diversity
and SU MIMO
IPv4/6 dual IP stack
DHCP
NAI based upon the IMSI
11digit MDN
LTE
Support for IPv4/6 (need to test
with Network)
CDMA
N/A
LTE
N/A
1.1 Feature
IP Mobility
QoS
IRAT handoff
Mechani
cal
Mechanical
QoS
CDMA
N/A
LTE
Proxy mobile IPv4/6
eHRPD
N/A
LTE
Support
CDMA
N/A
Active handoff
N/A
Non optimized
handover
Idle handoff
N/A
Non optimized
handover
IRAT measurement
N/A
Dimensions (W xD xH)
185 x 133.9 x 22.8 mm
Weight
420g
Antenna
Internal Antenna (MIMO)
2
Mechanical description
2.1 Front / Rear / Side View
2.1
Front / Rear / Side View
2.1. Front / Rear / Side View
2.2 Dimension
2.2
Dimension
M13 Mechanical dimension is 133.9 x 185 x 22.8mm.
2.2. Dimension
Functional description
3.1 Functional Key description
3.1
Functional Key description
LTE trial device picture is below.
This product has some key to operate LTE trial device.
Send key
Clear key
End key
: This key is used to call.
: This key is used to erase character or number.
: This key is used to disconnect a call and stop to function.
3.2. External connector description
3.2
External connector description
Our LTE Trail device has several external connectors.
DC input jack connector: External Power source, 5V TA
USB connector: USB Connect to Host (PC)
SIM socket: for LTE Authentification
24Pin connector: For debug LTE Sub board
HW Reset key
DC input Jack
USB cap
SIM socket cap
24Pin connector for LTE Sub board debugging
Earphone jack connector
3.3 External RF connector description
3.3
External RF connector description
LTE MIMO ANT mobile SW
LTE Main ANT mobile SW
GPS ANT mobile SW
CDMA ANT Mobile SW
LTE Trial device has 4 external RF connectors in order to measure wired RF
performance characteristic.
It is configured that LTE ant part is two external ANT port; LTE main ANT mobile
switch and LTE MIMO ANT mobile switch, and CDMA ANT mobile.
If you want to test LTE RF performance, you can use this external ANT port.
3.4. Antenna description (LTE & CDMA)
3.4
Antenna description (LTE & CDMA)
3.4.1
CDMA Antenna description
M13 Device LTE Antenna: Dual band, Single Feeding Antenna
Type: Carrier & PIFA
Directive: Omni-directiona
Ant. : 1TX and 1RX
CDMA 3D Gain: TX:--5.9dB, RX: -3.7dB
USPCS 3D Gain: TX: -6.1dB, RX: -5.1dB
Max Power: 2W (Maximum)
Band Support
3.4.2
LTE Antenna description
M13 Device LTE Antenna: MIMO Antenna
Type: Carrier & PIFA
Directive: Omni-directional
LTE Band 13 Support: UL; 777~787(MHz), DL;746~768(MHz)
Antenna Band: 740 ~ 800 (MHz)
Max power: 2W(Maximum)
Primary Ant. : 1TX and 1RX
Secondary Ant.: 1RX
3D Primary Antenna Gain: -1.32dB(Average)
3D Secondary Antenna Gain: -1.34(Average)
3.5 External Power description
3.5
External Power description
To operate and charge the battery, plug the AC Adapter into a standard wall outlet
and connect it to the LTE trial device via the DC input jack Connector.
External power supply is DC input jack or TA. This power supply specification is
below.
Input Voltage & Current
Output Voltage & Current
3.6 Battery description
3.6
Battery description
Our LTE Trial device has a two Battery. One is used for operating CDMA modem part,
and another is used for operating LTE modem part.
Battery Capacity for used in CDMA part is 1100mAh.
But in order to operating fully LTE performance, it is need to larger battery capacity.
And then we selected 2400mAh cylindrical battery.
Total Battery capacity is 3600mAh
If the battery’s charge is completely run down, it takes 6 to 7 hours to fully recharge.
But this battery capacity is not enough to operate LTE capability; you should external
power supply, which is TA (Travel Adaptor). The mandatory power supply of the LTE
UE is supplied by TA which is distributed by the LGE.
M13
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.6
Linearized : No
Encryption : Standard V2.3 (128-bit)
User Access : Print, Extract, Print high-res
XMP Toolkit : 3.1-702
About : uuid:f4ad7d75-b1db-49df-b687-6d98f31f6b9b
Producer : Acrobat Distiller 8.1.0 (Windows)
Creator Tool : PScript5.dll Version 5.2
Modify Date : 2009:06:23 14:12:48-04:00
Create Date : 2009:06:05 04:09:49+01:00
Metadata Date : 2009:06:23 14:12:48-04:00
Document ID : uuid:8c166b3f-b97d-4f92-b3fa-5bebb303dd64
Instance ID : uuid:26f7cc84-ebec-4618-a2eb-04ba63a33f00
Format : application/pdf
Title : Microsoft Word - M13 User Manual.doc
Creator : ddilboy
Has XFA : No
Page Count : 21
Author : ddilboy
EXIF Metadata provided by EXIF.tools