LG Electronics USA M173WAB 17" LCD TV/MONITOR User Manual User s Manual H

LG Electronics USA 17" LCD TV/MONITOR User s Manual H

Contents

USERS MANUAL 1

EUT Type: 17” LCD TV/Monitor FCC ID: BEJM173WAB Test Report No.: GETEC-E3-05-001 FCC Class B Certification APPENDIX H : USER’S MANUAL
WARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user tothe presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-cient magnitude to constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presence ofimportant operating and maintenance (servicing) instructions in the literature accompanying the appli-ance.WARNING:TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.NOTE TO CABLE/TV INSTALLER:This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National ElectricCode (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cableground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac-tical.REGULATORY INFORMATIONThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Any changes or modifications not expressly approved by the party responsible for compliance could void theuser’s authority to operate the equipment. CAUTION:Do not attempt to modify this product in any way without written authorization from Mitsubishi Digital ElectronicsAmerica. Unauthorized modification could void the user’s authority to operate this product.COMPLIANCE:The responsible party for this product’s compliance is:Mitsubishi Digital Electronics America9351 Jeronimo RoadIrvine, CA 92618Phone: (949) 465-6000CAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENWWarningarning
Please read these safety precautions carefully before using the product.Precautions in installing the ProductIf you ignore the caution message, you may be slightly injured or the product may be damagedIf you ignore the warning message, you may be seriously injured or there is a possibility ofaccident or death.Keep away from heat sources like electrical heaters.- Electrical shock, fire, malfunction or deformation may occur.Keep the packing anti-moisture material or vinyl packing out of the reach of children.- Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit thenearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.Do not put heavy objects on the product or sit upon it. - If the product collapses or is dropped, you may be injured. Children must pay particular attention.Do not leave the power or signal cable unattended on the pathway.- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.Install the product in a neat and dry place.- Dust or moisture can cause electrical shock, fire or product damage. If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact theservice center. - If you continue to use without taking proper measures, electrical shock or fire can occur.If you dropped the product or the case is broken, turn off the product and unplug the power cord. - If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the servicecenter.Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or inflammableobjects such as paper and matches. Children must pay particular attention.- Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord andcontact the service center.Make sure the product ventilation hole is not blocked. Install the product in a suitably wide place (morethan 10cm from the wall)- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat.Do not block the ventilation hole of the product by a tablecloth or curtain.- The product can be deformed or fire can break out due to overheating inside the product.Install the product on a flat and stable place that has no risk of dropping the product.- If the product is dropped, you may be injured or the product may be broken.Install the product where no EMI occurs.Keep the product away from direct sunlight.- The product can be damaged.Safety PrecautionsWarningWarningCautionCaution
Electrical Power Related PrecautionsMake sure to connect the power cable to the grounded current.- You may be electrocuted or injured.Use the rated voltage only.- The product can be damaged, or you may be electrocuted.During a thunder or lightning storm, unplug the power cable or signal cable.- You may be electrocuted or a fire can break out.Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet. Use apower bar with a grounding terminal designed for exclusive use with the computer.- A fire can break out due to overheating.Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, drythe power plug completely or wipe dust off.- You may be electrocuted due to excess moisture.If you don’t intend to use the product for a long time, unplug the power cable from the product.- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.Fix the power cable completely.- If the power cable is not fixed completely, a fire can break out.Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or putheavy objects on the power cord.- The power line can be damaged, which may cause electric shock or fire.Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end isconnected to the input terminal on the wall. Additionally, do not touch the power cable right afterplugging into the wall input terminal.- You may be electrocuted.Do not unplug the power cord while the product is in use.- Electrical shock can damage the product.WarningCautionENGLISHPrecautions in Moving the ProductWarningMake sure to turn off the product.- You may be electrocuted or the product can be damaged.Make sure to remove all cables before moving the product.- You may be electrocuted or the product can be damaged.
Remote Control/Batteries (AAA x 2)Power CordAudio Cable (PC)Please check the accessories in the product package.* The product and the accessories can be different from the figures shown here.D-Sub Signal Cable DVI-D Signal CableENGLISHAccessoriesCable CapUser's Guide / Drive CDUSB Cable(only applies to the20.1 inch product)1. Take out the battery cap.2. Insert the battery with correct polarity (+/-).3. Close the battery cap.• You can use a remote controller 7 meter distanceand 30 degree (left/right) within the receiving unitscope.• Dispose of used batteries in the recycle bin toprevent environmental pollution.Inserting batteries into remote control.Speaker Cover (2ea)/Cover Picker
ENGLISHRear ViewDVI Signal ConnectorDSUB Analogue Signal ConnectorAudio Jack :Connect to the jack in the PC sound card.HDTV Input/Output Terminal : Connect the HDTV CABLETV Tuner Jack: Connect the antenna.Power Cord Connector : Connect the power cord.Theft prevention locking device20.1 inch17 inchFirst, pull out the back cap attached to the rear of the product to detach, as shown.Back Cap- Open the back cap beforeyou install the product.20.1 inch 17 inchName and Function of the Parts
ENGLISHRear ViewHeadphone/Earphone Connection TerminalS-Video Input TerminalAV(CVBS) Input Terminal (Audio)Video(CVBS) Input TerminalUSB downstream PortUSB upstream PortCard ReaderS-VideoS-VideoS-VideoSide View (Optional-20.1 inch)20.1 inch17 inch
PC Audio Input Terminal- Connect the audio cable to the LINE OUT jack in the PC sound card.½Make sure to check the sound card connection terminal in the PC before connecting to the product.If the PC sound card supports both Speaker Out and Line Out, change it to Line Out by setting the jumperor the PC application. (For more details, refer to the sound card user’s manual.)-Speaker Out : The terminal connected to the speaker that is not equipped with an amplifier.- *Line Out : The terminal connected to the speaker equipped with an amplifier.If Audio Out in the PC sound card has only Speaker Out, reduce the PC volume. This product is integratedwith an amplifier.Connecting the sound card output terminalSound card Connection Terminal / HDTV Input TerminalHDTV Input TerminalName and Function of the Parts
ENGLISHConnecting to External DevicesS-VideoS-VideoWhen Connecting to your PCFirst of all, see if the computer, product and the peripherals are turned off. Then,connect the signal input cable and Audio cable.When connecting with the DVI signal input cable.When connecting with the DSUB signal input cable. (IBM compatible PC)When connecting with the DSUB signal input cable. (Macintosh)PCRear side of the product.BABAMACMacintosh Adapter (Optional)Use the standard Macintosh adapter since an incompatibleadaptor is available in the market. (Different signaling system)CC20.1 inch17 inchAudio cable
ENGLISHTVVideoS-VideoComponentRGBDVI Card ReaderI/IITV/AV*/SSMCHVOLVOLCHSETSETWhen connecting with a DVI signal input cable.• Select DVI : DVI digital signal.When connecting with a DSUB signal input cable.• Select RGB: DSUBanalog signalTurn on power by pressing the power button on the product.Turn on the PC. Select an input signal.Press the SOURCE button on the remote controller to select the input signal. Or, press the SOURCE button at the front side of the product.BACHPower button(SELECT)½How to connect to two computers.Connect the signal cables (DVI and RGB) to each computer.Press the SOURCE button in a remote controller to select the computer to use.½Directly connect to a grounded power outlet on the wall or a power bar with a groundwire.Note* Card Reader : Optional*

Navigation menu