LG Electronics USA US100 5-Port USB Hub User Manual Manual

LG Electronics USA 5-Port USB Hub Manual

Users Manual

USB Self-Powered Tilt/SwivelStandInstallation GuideDigital Equipment Corporation
2May 1998The information in this document is subject to change without notice and should not be construed as a commitment byDigital Equipment Corporation. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject torestrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause atDFARS 252.227-7013.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. Any changes or modification made to this equipment may void the user’s authority to operatethis equipment.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio and television reception; however, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one of the following measures:• Re-orient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.DO NOT attempt to modify this equipment. If modified, the FCC may void your authority to operate this equipment.VCCI Class 2 - JapanCanadian Department of Communications StatementThis Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.DEC and the DIGITAL logo are trademarks of Digital Equipment Corporation. 1998 Digital Equipment Corporation.All Rights Reserved.
iiiContentsIntroduction......................................................................................... 1Tilt/Swivel Stand Installation.............................................................. 1Removing a Previously Installed Tilt/Swivel Stand........................................................ 1Installing the USB Tilt/Swivel Stand.............................................................................. 1USB Tilt/Swivel Stand Specifications................................................ 2AudienceThis guide is intended for user’s who wish to install a USB tilt/swivel stand on their monitor.
iv
1IntroductionThe USB Tilt/Swivel Stand is an optional tilt/swivel stand for your monitor. It is self-powered having its own power supply and needs an external AC power source. The USBtilt/swivel stand provides up to seven downstream ports of you to connect USB compliantoptions. All downstream ports support both full- and low-speed operations.You install the USB tilt/swivel stand instead of the normal tilt/swivel stand that comes withyour monitor. If your monitor already has a stand installed on it, you will need to removethis stand first, before installing the USB tilt/swivel stand.Tilt/Swivel Stand InstallationRemoving a Previously Installed Tilt/Swivel StandTo remove the stand already installed on your monitor, pull on the latch or other mechanism toremove the stand. Refer to your monitor installation guide for specific instructions.Installing the USB Tilt/Swivel StandTo install the tilt/swivel stand: Insert the hooks on the stand into the bottom of the monitor. Apply pressure near the back of the bash so it slides forward and become secure. Set the monitor on the stand. Connect the power unit to back of the tilt/swivel stand and to the power source.
2Figure 1. USB Tilt/Swivel Stand Installation on Typical MonitorUSB Tilt/Swivel Stand Specifications• Fully compliant with USB Specification 1.0• Maximum of 7 down-stream ports available• Full Speed and Low Speed Operation• Individual or Global over current protection• Fully compliant with both UHCI and OHCI• One internal down-stream port for monitor if desired• Weight: 5.5 Kg (12.1 lbs)• Height: 8.6 cm (3.37 in)• Width: 27.9 cm (11.0 in)• Depth: 28.6 cm (11.25 in)

Navigation menu