LG Electronics USA W2343TV LCD Monitor User Manual Lx6WTG Q ENG
LG Electronics USA LCD Monitor Lx6WTG Q ENG
Contents
- 1. User manual 1
- 2. User manual 2
User manual 2
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~15˚ 15 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . NOTE This is a simplified representation of the rear view. A Connect DVI-D Cable This rear view represents a general model; your display may differ from the view as shown. B Connect D-sub Cable (PC) User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product. C Connect D-sub Cable (Mac) Power Cord Signal Cable Varies according to model. Wall-outlet type Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. DVI-D(This feature is not available in all countries.) 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. A6 Connectingthe theDisplay Display Connecting Using the cable holder OPEN Cable holder OPEN OP EN A7 Control Panel Functions Front Panel Controls FUN Button MENU Button Use this button to enter 4:3 IN WIDE,PHOTO EFFECT items, for more information, refer to page A16. Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. A8 Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A15. Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is -W2043T : 1600 x 900 -W2243T/W2343T : 1920 x 1080 Power Button Use this button to turn the display on or off. Power Indicator This Indicator lights up as red when the display is operating normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to flicker. A9 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: MENU AUTO/SET MENU Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A10 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu Reference 4:3 IN WIDE PHOTO EFFECT PICTURE COLOR BRIGHTNESS CONTRAST GAMMA sRGB PRESET 6500K 9300K To adjust the brightness, contrast and gamma of the screen To customize the color of the screen RED GREEN BLUE TRACKING HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS SETUP To adjust the position of the screen To improve the clarity and stability of the screen LANGUAGE OSD To customize the screen status for a user's operating environment HORIZONTAL POSITION VERTICAL WHITE BALANCE POWER INDICATOR FACTORY RESET FLATRON F-ENGINE MOVIE INTERNET USER NORMAL DEMO To select or customize desired image settings : Adjustable A : Analog Input D : Digital Input NOTE The order of icons may differ depending on the model (A11~A17). A11 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu Button Tip Menu Name 100 Icons 70 Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A12 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. 100 70 CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR COLOR PRESET Select the screen color. • sRGB: Set the screen color to fit the SRGB standard color specification. • 6500K: Slightly reddish white. • 9300K: Slightly bluish white. RED Set your own red color levels. GREEN Set your own green color levels. MENU : Exit BLUE : Decrease : Increase SET : Select another sub-menu Set your own blue color levels. A13 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. SHARPNESS To adjust the clearness of the screen. 90 MENU : Exit : Decrease : Increase SET : Select another sub-menu A14 On Screen Display(OSD) Selection and Adjustment Main menu SETUP Sub menu LANGUAGE To choose the language in which the control names are displayed. OSD POSITION To adjust position of the OSD window on the screen. WHITE BALANCE If the output of the video card is different the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image. Activate this function when white and black colors are present in the screen. POWER INDICATOR Use this function to set the power indicator on the front side of the monitor to ON or OFF. If you set OFF, it will go off. If you set ON at any time, the power indicator will automatically be turned on. FACTORY RESET Restore all factory default settings except "LANGUAGE." Press the button to reset immediately. SETUP MENU : Exit : Adjust : Adjust SET : Select another sub-menu Description If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be enabled only when the input signal is an analog signal. A15 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the FUN button on the left bottom of the monitor. Main menu Sub menu 4:3 IN WIDE Description To select the image size of the screen. WIDE 4:3 • WIDE : Switch to full screen mode according to input image signal. • 4 : 3 : Change the image signal ratio into 4:3. PHOTO To select the color of the screen. EFFECT • NORMAL : The PhotoEffect function is disabled. • GAUSSIAN BLUR : This option is to add the effect to the screen that the dark and sharp image becomes brighter and more blurred. NORMAL GAUSSIAN BLUR • SEPIA : This option changes the screen to be Sepia tone. The Sepia tone is brown color tone. • MONOCHROME : This option changed the screen to be Gray tone. The screen image is displayed with just white, black, gray colors. SEPIA MONOCHROME A16 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button on the left side of the monitor. Menu Name Icons Sub-menu Name Main menu Sub menu Description MOVIE This feature lets you easily select the best desired INTERNET image condition optimized to the environment (ambient illumination, image types etc). MOVIE: For animation images in videos or movies INTERNET: For text images (Word processing etc.) USER User You can manually adjust brightness, ACE or RCM. You can save or restore the adjusted value even when using a different environment. ...ACE(Adaptive Clarity Enhancer): Selects the clarity mode. ...RCM(Real Color Management): Selects the color mode. Not applied Green enhance Flesh tone Color Enhance NORMAL This is under normal operating conditions. DEMO This is just for advertising to customer in the shops. It’s setting is same with Movie mode and screen is divided by half. A17 Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? ● Is the power indicator light on? • Press the Power button. ● Is the power indicator amber? • If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC. ● Do you see an "OUT OF • This message appears when the signal from the PC (video card) is out of horizontal or vertical RANGE" message on frequency range of the display. See the the screen? 'Specifications' section of this manual and configure your display again. ● Do you see a "CHECK SIGNAL CABLE" message on the screen? • This message appears when the signal cable between your PC and your display is not connected. Check the signal cable and try again. Do you see a "OSD LOCKED" message on the screen? ● Do you see “OSD LOCKED” when you push MENU button? • You can secure the current control settings, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message “OSD UNLOCKED” will appear. A18 Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. • Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color). Important Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. A19 Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. ● The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Have you installed the display driver? ● Have you installed the display driver? • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www.lge.com. ● Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? • Make sure to check if the video card supports Plug&Play function. A20 Specifications Display Sync Input Video Input Resolution W2043T 20.0 inches (50.8 cm) Flat Panel Active matrix-TFT LCD AntiGlare coating Visible diagonal size: 50.8 cm 0.2766*0.2766 mm pixel pitch Horizontal Freq. Analog : 30 - 83 kHz (Automatic) Digital : 30 - 83 kHz (Automatic) Vertical Freq. 56 - 75 Hz (Automatic) Input Form Separate TTL, Positive/Negative SOG (Sync On Green), Digital (HDCP) Signal Input 15 pin D-Sub Connector DVI - D connector (Digital) Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital Max Recommend Plug&Play DDC 2B Power Consumption On Mode Sleep Mode Off Mode Dimensions & Weight Width Height Depth Net Analog : VESA 1600 x 900 @60 Hz Digital : VESA 1600 x 900 @60 Hz VESA 1600 x 900 @60 Hz ≤ ≤ 40 W(Typ.) 1W 1W With Stand Without Stand 48.36 cm / 19.04 inches 48.36 cm / 19.04 inches 37.68 cm / 14.83 inches 31.40 cm / 12.36 inches 18.30 cm / 7.20 inches 6.30 cm / 2.48 inches 3.2 kg (7.11 lbs) -5˚~ 15˚ Tilt Range Tilt Power Input AC 100-240V~ 50/60Hz 1.0A Environmental Conditions Operating Conditions Temperature 10˚C to 35 ˚C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20˚C to 60 ˚C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type or PC-outlet type NOTE Information in this document is subject to change without notice. A21 Specifications W2243T Display 21.5 inches (54.6 cm) Flat Panel Active matrix-TFT LCD, AntiGlare coating Visible diagonal size: 54.6 cm 0.248*0.248 mm pixel pitch Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Input Form Resolution Max Recommend Plug&Play DDC 2B Power Consumption On Mode Sleep Mode Off Mode Dimensions & Weight Width Height Depth Net Analog : 30 - 83 kHz (Automatic) Digital : 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate TTL, Positive/Negative SOG (Sync On Green), Digital (HDCP) 15 pin D-Sub Connector DVI - D connector (Digital) RGB Analog (0.7 Vp-p/ 75 ohm), Digital Analog : VESA 1920 x 1080 @60 Hz Digital : VESA 1920 x 1080 @60 Hz VESA 1920 x 1080 @60 Hz ≤ ≤ 40 W(Typ.) 1W 1W With Stand Without Stand 51.64 cm / 20.33 inches 51.64 cm / 20.33 inches 39.60 cm / 15.59 inches 33.27 cm / 13.10 inches 19.80 cm / 7.80 inches 6.20 cm / 2.44 inches 3.82 kg (8.49 lbs) -5˚~ 15˚ Tilt Range Tilt Power Input AC 100-240V~ 50/60Hz 1.0A Environmental Conditions Operating Conditions Temperature 10˚C to 35 ˚C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20˚C to 60 ˚C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type or PC-outlet type NOTE Information in this document is subject to change without notice. A22 Specifications W2343T Display 23 inches (58.4 cm) Flat Panel Active matrix-TFT LCD, AntiGlare coating Visible diagonal size: 58.4 cm 0.266*0.266 mm pixel pitch Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Input Form Resolution Max Recommend Plug&Play DDC 2B Power Consumption On Mode Sleep Mode Off Mode Dimensions & Weight Width Height Depth Net Analog : 30 - 83 kHz (Automatic) Digital : 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate TTL, Positive/Negative SOG (Sync On Green), Digital (HDCP) 15 pin D-Sub Connector DVI - D connector (Digital) RGB Analog (0.7 Vp-p/ 75 ohm), Digital Analog : VESA 1920 x 1080 @60 Hz Digital : VESA 1920 x 1080 @60 Hz VESA 1920 x 1080 @60 Hz ≤ ≤ 45 W(Typ.) 1W 1W With Stand Without Stand 55.52 cm / 21.86 inches 55.52 cm / 21.86 inches 41.85 cm / 16.48 inches 35.77 cm / 14.08 inches 19.80 cm / 7.80 inches 6.30 cm / 2.48 inches 4.42 kg (9.82 lbs) -5˚~ 15˚ Tilt Range Tilt Power Input AC 100-240V~ 50/60Hz 1.0A Environmental Conditions Operating Conditions Temperature 10˚C to 35 ˚C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20˚C to 60 ˚C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type or PC-outlet type NOTE Information in this document is subject to change without notice. A23 Specifications Preset Modes (Resolution) W2043T Display Modes (Resolution) Horizontal Freq. (kHz) 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1600 x 900 10 *11 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.981 79.976 60.000 Vertical Freq. (Hz) 70 60 75 60 75 60 75 75 60 75 60 *Recommend Mode W2243T/W2343T Display Modes (Resolution) 10 11 *12 Horizontal Freq. (kHz) 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.981 79.976 65.290 67.500 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1920 x 1080 Vertical Freq. (Hz) 70 60 75 60 75 60 75 75 60 75 60 60 * Recommend Mode Indicator MODE On Mode Sleep Mode Off Mode LED Color Red Flicker Off A24 Digitally yours
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : No Page Mode : UseOutlines XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 4.0 for Macintosh Modify Date : 2009:01:09 17:06:31+08:00 Create Date : 2007:01:17 10:13:56Z Creator Tool : QuarkXPress¢â: LaserWriter 8 KH-8.7.1 Metadata Date : 2009:01:09 17:06:31+08:00 Document ID : uuid:1dd76729-f3c4-428a-899a-2c471acd9de0 Instance ID : uuid:353ebbb0-37b2-4bf0-b6e4-de180bec401a Format : application/pdf Title : Lx6WTG_Q-ENG Creator : kjy Has XFA : No Page Count : 21 Page Layout : SinglePage Author : kjyEXIF Metadata provided by EXIF.tools