LG Innotek REBETZ42B2 Electronic Shelf Label User Manual Users manual

Download:
Mirror Download [FCC.gov]
Document ID	3685920
Application ID	WCwx4j3d8WilsypM43qkdA==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.47kB (405892 bits)
Date Submitted	2017-12-20 00:00:00
Date Available	2018-06-18 00:00:00
Creation Date	2017-11-28 18:12:18
Producing Software	Microsoft® PowerPoint® 2010
Document Lastmod	2017-12-18 15:53:51
Document Title	PowerPoint 프레젠테이션
Document Creator	Microsoft® PowerPoint® 2010
Document Author:	user

4.2” 3-Color Graphic type ESL
User manual
Model : REBE-TZ42B
Copyrightⓒ. 2015. All Rights Reserved.
1. Overview

Remote control device provides customer with several functions as below

Waking Tag up from sleep mode

Updating new purchase image on Tag

Deleting purchase image on Tag

Returning a Tag to be factory settings
Display Area
Profile Hook
Battery Cover
 Remo-con description
 LED : One of any buttons is pushed, red led turns on.
After sending some data to a Tag, red led will turn off.
 Registration : Updating New Purchase Information on Tag
 Release : Deleting Purchase Information on Tag
 Reset : Returning a Tag to be factory settings
 Keep Alive : Waking Tag up from sleep mode
Copyrightⓒ. 2015. All Rights Reserved.
2. Updating new purchase image on Tag
☜
To change purchase information on Tag, perform the following steps :
1.
Put remote controller near center of Tag‟s display
2.
Press and hold „Registration‟ button on remote controller until red LED off
(about 0.5 seconds)
3.
When Tag is successfully received „Registration‟ data from remote controller, Tag‟s
display will be changed to “Connected” for a few minutes. That means Tag hides
purchase image to read Tag‟s IEEE MAC address through the Barcode scanner.
4.
In NMS Client, download new purchase image to the Tag in registration status
5.
When image downloading is finished successfully, Tag‟s display will be changed to new
purchase image
Case1) If image downloading is failed, Tag‟s display will be changed to “Busy”.
After “Alive Time”, this Tag will be download new purchase image again
Copyrightⓒ. 2015. All Rights Reserved.
3. Deleting purchase information on Tag
☜
To release(delete) purchase information on Tag, perform the following steps :
1.
Put remote controller near center of Tag display
2.
Press and hold „Release‟ button until red LED off (about 0.5 seconds)
3.
If Tag was received „Reset‟ command from remote controller, Tag will delete
purchase information and Tag‟s display will be changed to “Ready”
4.
After step.3, Tag goes to deep sleep mode and doesn‟t communicate with gateway
until receiving „Keep Alive‟ or „Registration‟ data from remote controller
Copyrightⓒ. 2015. All Rights Reserved.
4. Waking Tag up
Case 1
Case 2
☜
Case 3
To wake Tag up from sleep mode, perform the following steps :
1.
Put remote controller near center of Tag display
2.
Press and hold „Keep Alive‟ button until red LED off (about 0.5 seconds)
3.
Tag will wake up and goes to next step. It‟s depends on connection information with gateway
case1) If this Tag wasn‟t connected with a gateway before sleep mode, go to 4-1
case2) If this Tag was connected with a gateway before sleep mode, go to 4-2
4-1. Searching gateway and goes to the next step. it‟s depends on searching results
case1) If Tag was successfully connected, Tag‟s display will be changed to “Ready”
case2) If Tag wasn‟t connected, Tag‟s display(may be “Ready”) will be refreshed
4-2. Sending „Keep Alive‟ packet to gateway and Tag will go to sleep mode again
case1) If Tag was received response from gateway, this Tag will go to “sleep mode” until
the specified time in gateway. After “sleep mode”, this Tag will send “Keep Alive” Packet to
gateway again.
case2) If Tag wasn‟t received response from Gateway, this Tag will retry three times. After that,
Tag‟s display will be changed to “Disconnected”. Also this Tag will perform a whole channel scan
every five minutes.
Copyrightⓒ.
. 2015. All Rights Reserved.
5. Returning a Tag to be factory settings
☜
To make a Tag to be factory reset status, perform the following steps :
1.
Put remote controller near center of Tag display
2.
Press and hold „Reset‟ button until Red LED off (about 0.5 seconds)
3.
If Tag was received „Reset‟ command from remote controller, Tag goes back to factory
settings and Tag‟s display will be changed to “Ready”
4.
After step.3, Tag goes to deep sleep mode and doesn‟t communicate with gateway
until receiving „Keep Alive‟ or „Registration‟ data from remote controller
case1) If Tag was received “Keep Alive” or “Registration” command from remote
controller, this Tag will perform a whole channel scan.
case2) If Tag was received “Reset” or “Release” command from remote controller,
Tag‟s display will be changed to “Ready” again
Copyrightⓒ. 2015. All Rights Reserved.
6. Tag status
Deep Sleep Mode
Disconnected with Gateway
Connected with Gateway
Image download Failure(“Busy”)
Battery discharge
(The battery needs to be replaced)
Copyrightⓒ. 2015. All Rights Reserved.
LG Innotek
7. Regulation Information
Confidential
Copyright ⓒ 2015. All Rights Reserved.
LG Innotek
Confidential

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Language                        : ko-KR
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : user
Title                           : PowerPoint 프레젠테이션
Create Date                     : 2017:11:28 18:12:18+09:00
Creator Tool                    : Microsoft® PowerPoint® 2010
Modify Date                     : 2017:12:18 15:53:51+09:00
Metadata Date                   : 2017:12:18 15:53:51+09:00
Producer                        : Microsoft® PowerPoint® 2010
Document ID                     : uuid:8dd5ad5b-721c-4140-8b16-0111dc477ab8
Instance ID                     : uuid:b086fe83-1507-49a4-8c74-43598f83747c
Page Count                      : 8
Author                          : user

EXIF Metadata provided by EXIF.tools