LG LDF6810BB User Manual DISHWASHER Manuals And Guides L0706335

LG Dishwasher Manual L0706335 LG Dishwasher Owner's Manual, LG Dishwasher installation guides

User Manual: LG LDF6810BB LDF6810BB LG DISHWASHER - Manuals and Guides View the owners manual for your LG DISHWASHER #LDF6810BB. Home:Kitchen Appliance Parts:LG Parts:LG DISHWASHER Manual

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

III IRL
_/°

III"°

Dishwasher
MODEL : LDF7810WW/ LDF7810BB / LDF7810ST
LDF7811WW/LDF7811BB / LDF7811ST
LDS5811WW/ LDS5811BB/ LDS5811ST
LDF6810WW/LDF6810BB / LDF6810ST

Please read this manual carefully.
Retain for future reference.

If you have questions, call 1-800-243-0000
or visit our website at: http://www.lgservice.com
or http://us.lgservice.com

PART 1. SAFETY

AND CAUTION

PART 2. DISHWASHER
PART 3. TOOLS

SPECIFICATIONS

AND MATERIALS

PART 4. INSTALLATION

...............................................................................................

IMPORTANT

When installing
following:
• Disconnect
• All electrical
codes.

.................................................................................

.............................................................................

NEEDED

INSTRUCTIONS

............................................................................

SAFETY

and using your dishwasher,

5~11

INSTRUCTIONS

follow basic precautions,

including

the

electrical power before you start !
wiring and grounding

should be done in accordance

with national and local

• If electrical supply is damaged, it must only be replaced by the manufacturer or its service
agent or a similar qualified person in order to avoid a hazard.
• This dishwasher must be connected to a hot water supply between 120°F (49 °C)-149°F (65 °C).
This temperature range provides the best washing results and shortest cycle time.
Temperature should not exceed 149°F (65 °C) to prevent damage to dishes.
• This appliance must be positioned close to an electrical power supply.
• The appliance is to be connected to the water supply using new hoses. Old hoses should not
be reused.

GROUNDING

INSTRUCTIONS

• For a permanently

connected

dishwasher:

This appliance must be connected to a grounded metal, permanent wiring system, or an
equipment-grounding conductor must be run with the circuit conductors and connected to the
equipment-grounding terminal or lead on the appliance.
2

Fully Integrated
LDF7810WW/BB/ST
LDF7811WW/BB/ST
LDF6810WW/BB/ST
• Power supply:
• Water Pressure:

Semi Integrated
LDS5811WW/BB/ST

Product Dimension

120V, 60Hz AC only
20 - 120 psi

1/5"(5mm)

(140 - 830 kPa)
• Size: Fully / Semi (WxDxH):
23 7/8"x 24 5/8"x 33 7/8"
(606mm

x 625mm

24-5/8"(625mm)

Felt
(insulating
material)
may be
compressed

x 860mm)

• Inlet Water Temperature:
120°F (49°C)
• Weight:

33-7/8"
(860mm)

115 Ibs. (52kg, Fully-

Integrated), 110 Ibs. (50kg, SemiIntegrated)
Specifications
are subject to change
to improve performance.

The features on your dishwasher
may vary from the figure shown.

3-1/4"(83mm)

=20-3/8"(518mm)

Water supply hose, Drain hose
and Electric Cable
Should be passed through by this area

1-3/8"(35mm)

_ _ _, _ _ [i¸_ i_i...._
[Seepage8 lor inslallalion delaill
INSTALL BRACKET

WOOD SCREW

(Notprovided]

0
ELECTRICALCABLE

AIR GAP

o©

WATERSUPPLYTUBE

TWIST-ON WIRE
CONNECTOR

ELBOW

HOSE CLAMP

FITTINGS
FORTUBE

RUBBER
CONNECTOR

STRAIN RELIEF

PLUMBERS'
TAPE

ELECTRICAL TAPE

yY
STANDARD
SCREWDRIVER

ADJUSTABLE
WRENCH

NIPPER

PHILLIPS
SCREWDRIVER

HOLE CUTTER

TAPE MEASURE

PLIERS

ELECTRIC DRILL

CUTTING KNIFE

WIRE STRIPPER

GLOVES

LEVEL

SAFETY GLASSES

TUBING CUTTER

PREPARE CUPBOARD
.

This dishwasher

is designed

to fit a standard

dishwasher

OPENING
opening

2. Select a location as close to sink as possible for easy connections
3. The dishwasher
drainage.
.

as shown below.
to water and drain lines.

should not be installed more than 10 ft. (3m) from the sink for proper

If dishwasher is to be installed in a corner, a minimum
the dishwasher and an adjacent a wall.

of 2 in. (50mm)

is required

between

To allow for proper clearance of plumbing and electrical measure a 4"x4" target area (figure
#1 ) on the side of the cabinet where the cabinet meets the back wall. Using a 2 1/2"
diameter hole saw drill a hole (in the target area) within 4" from the floor, and no more than
an 1 5/8" from the back wall. If there is a floor in the cabinet under the sink, it will also be
necessary

to drill or cut through

the floor to connect

the water and drain under the sink.

Failure to cut this opening will result in the drain hose interfering with the rear wall not allowing
for flush mount installation.

figure

Must
have this opening
side) to route plumbing
electrical.

•

Ensure

(on either
and

the floor under the dishwasher

allow for any service

For FLUSH INSTALL, you may
remove
the Cabinet brace inside of

is at the same level as the rest of the room to

requirements,

iii

PR E PA R E T H E E LEC T R IC A L W IRIN G

WARNINGS
For personal safety; remove house fuse or open circuit breaker before
insta!lation. Do not usean extension cord or adapter plug with this dishwasher,
Electrical and grounding connections must comply with the national electrical
code/provincial
and municipal code and!or other local codes.

This appliance must be operated with correct voltage as shown in this manual and on the
rating plate, and connected to an individual, properly grounded branch circuit, protected by
time delay fuse. Wiring must be 3 wires including ground.

The wiring or cord should be in an accessible location adjacent
dishwasher and within 4 ft. (1.2m) of the dishwasher side.

The wiring or cord must be grounded properly, if in doubt, have it checked by a qualified
electrician. No other appliance shall be connected to the same outlet by a double adapter
or similar plug.

The wiring or cord must be oriented

5 Check the dishwasher
6 Make sure Electrical

as shown in Figure below.

for any damage
line are oriented

If you find any damage
immediately.

to, and not behind the

before trying to install it.
in the bottom

to the dishwasher,

channels

as shown in the figure below.

Please contact your dealer or builder

Electrical Cable
5 1/2- 6 114" (140- 160ram)

PREPARE THE WATER SUPPLY CONNECTION
1. This dishwasher must be con nected to a hot water supply between 120 °F(49 °C )- 149 °F (65 °C).
This temperature range provides the best washing results and shortest cycle time.
Temperature should not exceed 149°F(65 °C) to prevent damage to dishes.
2. When connecting
avoid leaks.

the dishwasher

water line, sealing

3. When connecting

the dishwasher

water line, the house supply should

4. The Water Supply

Tube must be oriented

tape or compound

in the bottom channels

should

be used to

be shut off.

as shown in the figure below.

Electrical Cable

8 1/4 - 9 1/4" (208 - 233mm)

PREPARE

DISHWASHER

Don't pull handle.

Open door and grab body frame and top

Doing so can result in door distortion.

front opening

of tub.

iii

_xll

R EIVl0 V E L0 W ER C OV E R
• Remove two screws
to dishwasher.
• Remove

attaching

lower cover

lower cover from base.

SLIDEDISHWASHER
INTOCABINET
• Slide the dishwasher into the cabinet opening
carefully.
• Make sure the drain hose inside the cabinet
is not kinked.

Electrical
Cable

Drain Hose
Water Supply Tube

FITTING 90 ° ELBOW
• When fitting elbow into the inlet valve,
sealing tape or sealing compound should
be used to avoid water leaks.
• Install a 90 ° elbow onto the water valve.

LEVEL DISHWASHER

• Check that the dishwasher
Attach

is level. (Fig. A)

level on top front opening

of tub from side to side

• Check that the dishwasher is plumb. (Fig. B)
Attach level on front side of cabinet

• Check that gap between

Fig. C

-It

• If the dishwasher is not level or both side gap is not equal,
adjust four leveling feet up or down until dishwasher is level
and both side gap is equal. (Fig. D)

Fig. D

SECURE DISHWASHER
•

door and tub is equal on both side's

(L, R) (Fig. C)

TO THE COUNTERTOP

Secure dishwasher to the countertop or the cabinet.
When the countertop is made of wood or will not be damaged by drilling, use Step 9-1.
When the countertop is made of granite, marble or others which could be damaged by
drilling, Use Step 9-2.
STEP 9-1

STEP 9-2

1. Locate the installation brackets in the slot
2. Bend the brackets to secure them to the
dishwasher

tub

3. Secure the dishwasher to the countertop
with the screws provided through the
holes in the bracket

1. Remove the Plastic Bushing
2. Drive Wood Screw through the hole
(Install Bracket is located between tub
and side cabinet by manufacturer)
3. Reinstall Plastic Bushings.

9
ii

iii

_xll

DRAIN LINE CONNECTION
1. If the end of the drain hose does not fit to the drain line, use an adapter (not supplied)
must be resistant to heat and detergent and may be obtained from a plumbing shop.
2. There are 2 typical

connections

as shown in Fig. E & F.

(b There may be other options than shown here for connection
connection must meet local plumbing regulations.

of the drain hose. The drain

(2) The S trap spigot must be drilled out cleanly and free of obstruction
internal diameter, if used for drainage.
(3) To prevent syphoning,
Fig. E: Connection

one of the following

to Disposer

that

instruction

methods

to its maximum

must be followed:

or Waste Tee.
I

Dishwasher
Sink

Drain Hose

In case Fig. F, Cut off the
Drain Hose in a dotted line

Min. 20" (508mm)
Min. 30" (770ram) __
Max. 40" (1000mm)

Fig. F: Connection

• Follow local codes and
ordinances.

to Air Gap.
Air Gap

Dishwasher
Sink

Drain Hose

• Do not exceed 10 ft. (3m)
distance to drain.
• Do not connect drain lines from
other devices to the dishwasher
drain hose.

WATER SUPPLY CONNECTION
1. Before connecting,

turn off the

water supply.
2. After fitting the Elbow into the
Inlet Valve, slide the Flexible
Stainless Tube or Copper
into the Elbow.

netWve
Ebow
!!!!!

Tube

WaterSupplyTube
,

sharply

bent.

ELECTRICAL
,

...................

Tighten the nut and make sure
that the line is not kinked or

Before beginning,

POWER CONNECTION

turn off

electrical power to the unit at
the circuit breaker.
,

Remove the Junction Cover
and then Install the Strain
Relief.
I

3. Twist Wire Connectors tightly
on the wires. Wrap each
connection

with Electrical

JunctionCover ........-....

tape.

4. Check again and make sure
that all wires are connected
correctly, black to black, white
to white, green to green
(ground to ground).
WireConnector
5. Replace
Junction

the
Cover.

- blackto black
_. greento green
(groundto ground)

JunctionCase
whiteto white
StrainRelief

FINAL CHECK
1. Turn electrical power back on at the circuit breaker.
2. Turn house water supply back on.
3. Operate the dishwasher through one cycle (Quick cycle is recommended)
leaks and operating conditions.
4. Replace

to check for water

the Lower Cover.

11
ii

LG Electronics

P/No.: 3828DD3003A

Inc.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 12
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Mon Aug 06 21:56:25 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

LG LDF6810BB User Manual DISHWASHER Manuals And Guides L0706335

LG Dishwasher Manual L0706335 LG Dishwasher Owner's Manual, LG Dishwasher installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation