LIAN LI BORA120R Controller User Manual G50 120000 0001
LIAN LI INDUSTRIAL CO.,LTD. Controller G50 120000 0001
LIAN LI >
Users Manual
Press and hold for 5 seconds
to disconnect 1 to 1 pair up.
It will also reset all setting.
(Only for RF version).
Press and hold for 5 seconds
to disconnect 1 to 1 pair up.
(Only for RF version)
長按 5 秒
恢復所有遙控器通用
( 只針對RF版本有效 )
，解除一對一匹配，
長按5秒
(只針對RF版本有效)
，解除一對一匹配售
控制器使用指南
Press Off
to save setting
按 Off 保存
1. 按 Off 。
2. 按 AUTO ，風扇會跳出三個燈顏色。
3. 按藍色鍵，調整燈顏色的順序，直到三個燈
顏色順序為紅、綠、藍為止。
4. 按 Off 保存。
5. 按 On，再按各顏色鍵，
顯示各顏色鍵的顏色。
1. Press Off .
2. Press AUTO, the fan will the
three colors.
3. Press the blue button to adjust the order
of the colors until the three LEDs
4.
5.
prompt
LED
LED
sequence is in Red, Green and Blue.
Press Off to save setting.
Press On, then press the color button to
display the color of the color button.
B
G
R
綠
紅
藍
On
AUTO
Off
Increase brightness
Speed up
Decrease brightness
Slow down
Change to next light effect
Go back to previous light effect
To set single color directly
Press Off button and then this button
in order to enter menu mode.
In menu mode, press M+ and M- to set
number of addressable LEDs; press
blue button to change RGB sequence.
Press Off to save and exit.
Press once to run
all light effect
Turn Off LEDs
Turn on or pause
按 Off 後再按此鍵進入設置菜單
按M+ 和 M-來調節LED點數，按藍色鍵可以
調節RGB 順序，設置完成按 Off 保存退出。
，這時可以
關機
亮度+
亮度-
按一下為自動播放
所有模式
開機/播放暫停
速度+
速度 -
靜態單色
按下顯示對應顏色
，快捷按鈕
模式+
模式 -
Controller User’s Guide
Please install fan according to Fan numbering sequence (1, 2, 3),
otherwise the LED will not function. Fan output 4, 5 and 6 have
the same pattern as Fan output 1, 2, and 3.
請按 1、2 3 順序插上，要不然 LED 不亮
1、2、3 一樣。
、 ，4、5、6 的功能跟
主型號
(Model Name):
BORA120R-1
FCC ID:
2ANYX-BORA120R
Magnell Associate, Inc. dba Newegg. com
17560 Rowland St, City of Industry, CA 91748, USA
Tel: 626. 271.1420
Distributor:
Magnell Associate, Inc. dba Newegg. com
17560 Rowland St, City of Industry, CA 91748, USA
Tel: 626. 271.1420
Distributor:
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with
minimum distance between 20cm the radiator your body: Use only the supplied antenna.
FCC ID: 2ANYX-BORA120R
控制器使用指南
Controller User’s Guide
G50.120000.0001