LINKSYS WAG54GV2M WLAN 802.11g MiniPCI Card User Manual

LINKSYS LLC WLAN 802.11g MiniPCI Card Users Manual

Users Manual

Download: LINKSYS WAG54GV2M WLAN 802.11g MiniPCI Card User Manual
Mirror Download [FCC.gov]LINKSYS WAG54GV2M WLAN 802.11g MiniPCI Card User Manual
Document ID407717
Application IDAW/urOaJPgZZwMQms6q7Lw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize57.17kB (714600 bits)
Date Submitted2004-03-24 00:00:00
Date Available2004-03-24 00:00:00
Creation Date2004-03-16 10:24:38
Producing SoftwareAcrobat PDFWriter 5.0 for Windows NT
Document Lastmod2004-03-18 15:21:35
Document TitleC:\Documents and Settings\jane\桌面\FCC Statement.prn.pdf
Document CreatorMicrosoft Word - 2.4GHz_ Mobile of module
Document Author: jane

Configuration Utility
User’s Guide
Revision 0.1
1
Introduction........................................................................................................................... 3
1.1
List of abbreviations and Terms............................................................................................ 3
Installation............................................................................................................................. 4
Using the TI WLAN CU....................................................................................................... 5
3.1
3.2
The Main (Status) Screen ....................................................................................................... 6
The Modify Property Sheet .................................................................................................... 9
3.2.1
3.2.2
3.3
3.4
The Advanced Properties Screen......................................................................................... 12
The Privacy Screen ................................................................................................................ 14
3.4.1
3.4.2
3.5
3.6
3.7
The New Connection tab ............................................................................ 9
Advanced tab ............................................................................................ 11
The WEP Screen ....................................................................................... 15
The CCX Configuration Screen................................................................ 16
The Statistics Screen.............................................................................................................. 17
The About Screen................................................................................................................... 18
Debug Screen .......................................................................................................................... 19
3.7.1
3.7.2
Revision 0.1
Debug Tab activation................................................................................ 19
Debug Screen options ............................................................................... 20
1
Introduction
The configuration utility provides displaying and changing parameters of the TI WLAN driver.
1.1
List of abbreviations and Terms
AES
AP
BSS
BSSID
CU
FCS
GUI
IBSS
LEAP
MAC
MSDU
PBCC
PRS
RSSI
SSID
SSN
TI
TKIP
WEP
WiFi
WPA
WLAN
Revision 0.1
- Advanced Encryption Standard
- Access Point
- Basic Service Set
- Basic Service Set Identifier
- Configuration Utility
- Frame Check Sequence
- Graphical User Interface
- Independent Basic Service Set
- Lightweight Extensible Authentication Protocol
- Medium Access Control
- MAC Service Data Unit
- Packet Broadcast Control Channel
- Product Requirements Specification
- Received Signal Strength Indication
- Service Set Identifier
- Sub System Number
- Texas Instruments Inc.
- Temporal Key Integrity Protocol
- Wired Equivalent Privacy
- Wireless Fidelity
- WiFi Protected Access
- Wireless Local Area Network
2
Installation
Revision 0.1
3
Using the TI WLAN CU
Important Notes:
•
In case that the device was not installed properly or that it is disconnected, all
buttons, combo boxes, edit boxes etc. will be disabled. Also the status text in the
main window will be set to Driver not loaded.
•
To save any changes – press the Apply button. Changes will not be saved if
changed focus to another tab without previously clicking the Apply button.
•
Pressing the OK / Cancel button from the main property sheet will minimize the
application to the task bar. In case that there were changes, clicking the Cancel
button will return the displayed data to the one stored on the driver. Another click
will minimize the application to the task bar. Left click the application icon on the
task bar, or right click and choose Restore to restore it. Choose Exit to exit the
application.
Revision 0.1
3.1
The Main (Status) Screen
The Main Screen is the main page for the CU. It contains the available 802.11 networks and the current configuration basic
data. It enables rescanning the network, modifying the current configuration parameters and connecting to each one of the
listed SSIDs. It also enables activating and deactivating of using an external configuration.
Revision 0.1
Getting Started:
In order to connect to a network, do the following:
1)
In the Available Networks Window the currently available networks are displayed. In order to connect to a specific
network – select the appropriate raw (will be highlighted as a result)
2)
Click on the Connect button (another option is to double click the appropriate raw). After doing so, the CU
will attempt associating with the chosen network. If there are no available networks on the available networks
window, you can choose to rescan for currently available networks by pressing the Rescan button.
After choosing a network, a basic connection data will be displayed on the screen. See Displayed data section for details.
If no network is available or refreshing the available networks list is desired – click on the Rescan button.
Displayed data:
Status – can be one the following:
•
Driver not loaded
–
•
Disconnected from network –
•
Connecting to network
–
•
Connected to network
–
•
Scanning network
–
•
Not connected to network –
Current configuration
•
Pref: SSID •
BSS Type
•
BSSID
•
Channe
•
Tx Rate
For more information, see
driver not installed or not inserted.
disconnected from current configured SSID.
while in the process of connecting.
connected to current configured SSID.
scanning network for available SSIDs.
sidle status
provides read-only status information of the current active connection.
Preferred Service Set Identifier.
Basic Service Set Type.
Basic Service Set Identifier.
the channel number through which we are connected.
current rate used for transmitting frames.
section 3.2.1
Signal quality
–
Tx Rate Rx Rate
displays instantaneous transmit and receive rates, in a graphical format. These
values are being refreshed every second.
Revision 0.1
displays the Received Signal Strength Indication as a percentage bar.
Modifying Current Connection Parameters
To modify the current connection parameters, click the Modify button. So, a new property sheet will be opened. This
property sheet contains two pages named ‘”New connection” and “Advanced”, see section 3.2.1 , see section 3.2.2 .
Advanced Configuration
Check the External Configuration check box for enabling privacy external configuration. By doing so, all three buttons
(Connect, Modify and Rescan) will be disabled, see section 3.4 – Privacy Screen for more details.
Summary
Connect button – use this button to initiate a connection to the network chosen in the Available Networks Window.
Rescan button –use this button to rescan and update the Available Networks Window.
Modify button – use this button to modify the current connection parameters.
External Configuration check box – check this check box for enabling privacy external configuration.
Revision 0.1
3.2
The Modify Property Sheet
Both New Connection and Advanced page contains the current connection modifiable parameters retrieved from the driver.
3.2.1
The New Connection tab
•
Preferred SSID – preferred Service Set Identifier - a string identifying the current configured service set.
•
BSS Type combo box – Basic Service Set Type. This field can be one of the following:
o 802.11 Ad hoc
o Infrastructure
o High-speed Ad hoc
•
Tx Rate combo box – Current rate used for transmitting frames. The available values depend on the BSS
•
Channel combo box
•
Power Mode combo box – This option enables stations power conserving by turning off receiver and
Type value and the Mode value.
– the channel number through which we are connected.
transmitter.
Revision 0.1
•
•
This field contains the following values:
o No Power Save
o Max Power Save
IBSS Protection combo box – Independent Basic Service Set protection can be one of the following:
•
•
4x Config radio button – select “4x enable” to enable 4x mode, and “4x disable “to disable it.
Tx Power Level combo box – Transmit power level. Can be one of the following:
•
Low Power
Medium-Low Power
Medium-Power
Medium-High Power
High Power
Mode combo box – selection of one of the standard 802.11 operating modes:
•
None
TI Protection
CTS Only
B-Only Mode
B-Plus Mode
B&G Mode
G-Only Mode
A-Only Mode
A&G Mode
Profile – Save a profile or load a stored profile. To save profile, enter a profile name within the combo box and
press save. To load an existing profile, choose the profile name from the comb box and press load. All of the
current configuration parameters will be changed to the saved profile parameters.
Revision 0.1
10
3.2.2
•
Advanced tab
Fragment Threshold edit box- the range of selectable values is 0 – 2347 inclusive. 2347 is the
default value.
•
RTS Threshold edit box - the range of selectable values is 0 – 2346 inclusive. 2346 is the default
value.
•
Preamble - the user can select either short or long.
•
Authentication combo box – Can be one of the following values:
•
Auto Switch
Shared Key
Open System
802.11g version – this section is enabled only with G-Only Mode operation mode selected on the New
Connection Page.
•
Antennas combo boxes – this section contains two identical combo boxes, having the following options:
•
Both
Antenna 1
Antenna 2
Retry limits Short edit box - the range of selectable values is 0 – 15.
Revision 0.1
11
•
3.3
Retry limits Long edit box - the range of selectable values is 0 – 15.
The Advanced Properties Screen
Read only advanced data for current configuration. Most of the parameters are those previously defined in the Modify
property sheet.
Additional parameters:
Left Side:
•
•
Authentication – defined in the Privacy screen. See next section for more details.
AP Tx Power Level – Current AP Tx power level in mW.
Revision 0.1
12
Network Information
• IP Address
• Net. Mask
• Gateway
Right side:
•
Encryption – defined in the Privacy screen. See next section for more details.
•
Regulatory Domain
For 2.4 GHz:
o FCC
o IC
o ETSI
o Spain
o France
o MKK
o MKK1
o Unknown
For 5 GHz:
o US
o World Band
o Extended World Band
– can be one of the following:
•
MAC Addr - MAC address
•
Country Code – represented by a 3 maximum length string.
Revision 0.1
13
3.4
The Privacy Screen
Note: This window will be disabled in case that the External Configuration
check box (in the Main window) was checked.
In this screen the privacy mode is being configured.
There are 3 optional privacy modes:
•
•
•
None – no security defined.
WEP -for WEP key defining. Press the Select button to change WEP configuration. A new dialog
window will be opened (see section 3.4.1).
CCX - for CCX configuration. Press the Select button to change CCX configuration. A new dialog
window will be opened (see section 3.4.2).
Revision 0.1
14
To use the external mode (privacy configured by Funk’s Odyssey software), check the External
Configuration check box in the main dialog and press the Apply button. All privacy
configurations will be disabled, until you uncheck the External Configuration check box.
3.4.1
The WEP Screen
Configure WEP keys:
•
Choose key size form the key
•
•
•
size combo box. Available values - 40 bit, 128 bit, 256 bit.
Add an encryption string within the Encryption edit box.
Choose authentication type from the Authentication combo box.
Available values – Open System, Shared Key, Auto Switch
Select default key by pressing the desired radio button.
Press OK to save and return to previous dialog, or cancel to cancel changes and return to the previous dialog.
Revision 0.1
15
3.4.2
The CCX Configuration Screen
Select an option from the Network Security Type combo box.
Available options are:
None – choosing it will enable the WEP Select button. By pressing it you will get to the same window
•
as described in see section 3.4.1
•
LEAP – choosing it will enable the Leap Credentials group box, where you can type the user ID and
password.
External –external CCX configuration.
•
Press OK to save and return to previous dialog, or cancel to cancel changes and return to the previous dialog.
Revision 0.1
16
3.5
The Statistics Screen
Contains general statistics data retrieved from the driver.
Revision 0.1
17
3.6
The About Screen
The about screen contains general version data.
Revision 0.1
18
3.7
3.7.1
Debug Screen
Debug Tab activation
Add the following text to shortcut definition as it shown on picture below.
Revision 0.1
19
3.7.2
Debug Screen options
The debug screen is used for directly accessing the hardware.
Revision 0.1
20
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device is intended only for OEM integrators under the following
conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their endproduct for any additional compliance requirements required with this module
installed (for example, Wireless AP , Wireless Router).
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users (for example, wireless AP , Wireless Router). The final end product must
be labeled in a visible area with the following: “Contains TX FCC ID: Q87WAG54GV2M”.
Manual Information That Must be Included
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the users manual of the
end product which integrate this module.
The users manual for OEM integrators must include the following information
in a prominent location “ IMPORTANT NOTE: To comply with FCC RF
exposure compliance requirements, the antenna used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cisco-Linksys, LLC declare that WAG54GV2M (WLAN 802.11g MiniPCI Card) is
limited in CH1~CH11 by specified firmware controlled in USA."

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2004:03:16 10:24:38Z
Modify Date                     : 2004:03:18 15:21:35+08:00
Page Count                      : 22
Has XFA                         : No
Creation Date                   : 2004:03:16 10:24:38Z
Author                          : jane
Producer                        : Acrobat PDFWriter 5.0 for Windows NT
Mod Date                        : 2004:03:18 15:21:35+08:00
Metadata Date                   : 2004:03:18 15:21:35+08:00
Title                           : C:\Documents and Settings\jane\桌面\FCC Statement.prn.pdf
Creator                         : jane
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Q87-WAG54GV2M

Navigation menu