LINKSYS WAP54GP Wireless-G Access Point with POE User Manual Book

Download:
Mirror Download [FCC.gov]
Document ID	539653
Application ID	1DblQUjEbKqcc3Vzk4S6Hw==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	194.59kB (2432402 bits)
Date Submitted	2005-05-05 00:00:00
Date Available	2005-05-04 00:00:00
Creation Date	2005-05-04 18:28:17
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2005-05-04 18:28:39
Document Title	Book Template.book
Document Creator	FrameMaker 7.0
Document Author:	junelee

Wireless-G Access Point with Power Over Ethernet
11. The Wireless Security Settings screen will appear next. From this screen, you can set the level of security you
desire for each of your three networks.
First, select the wireless network you want to configure, Main SSID, SSID1, or SSID2.
Then select from WEP (64-Bit), WEP (128-Bit), and WPA-Personal, and follow the appropriate instructions
below. If you want to use WPA-Enterprise, then select Disabled from the Security drop-down menu. (You will
have to use the Web-based Utility to set up WPA-Enterprise or RADIUS; for more information, refer to “Chapter
6: Configuring the Wireless-G Access Point with Power Over Ethernet.”)
After you have entered the settings for your three wireless networks, click the Next button to continue or
Back to return to the previous page.
For more information on wireless security, refer to “Appendix B: Wireless Security.”
• WEP (64-Bit) or WEP (128-Bit). Enter the Passphrase for your network. If want to manually enter the WEP
key, then leave the Passphrase field blank and enter the WEP key in the Key 1 field. The WEP key can
consist of the letters “A” through “F” and the numbers “0” through “9” and should be 10 characters in
length for 64-bit encryption or 26 characters in length for 128-bit encryption.
After you have entered the settings for your three wireless networks, click the Next button to continue or
Back to return to the previous page.
Figure 5-10: Wireless Security Settings - WEP Screen
wep (wired equivalent privacy): a method of encrypting
network data transmitted on a wireless network for greater
security.
bit: a binary digit.
wpa (wi-fi protected access): a wireless security protocol
using TKIP (Temporal Key Integrity Protocol) encryption,
which can be used in conjunction with a RADIUS server.
passphrase: used much like a password, a passphrase
simplifies the WEP encryption process by automatically
generating the WEP encryption keys for Linksys products.
Chapter 5: Setting Up the Wireless-G Access Point with Power Over Ethernet
Setup Wizard
16
Wireless-G Access Point with Power Over Ethernet
• WPA-Personal. With WPA-Personal, you will use TKIP or AES for encryption with dynamic keys. Then enter
a Pre-Shared Key of 8-63 characters.
After you have entered the settings for your three wireless networks, click the Next button to continue or
Back to return to the previous page.
Figure 5-11: Wireless Security Settings WPA-Personal Screen
tkip (temporal key integrity protocol): a wireless
encryption protocol that provides dynamic
encryption keys for each packet transmitted.
12. The Wireless Power Management screen will appear. You can adjust the power output of the Access Point to
get the appropriate coverage for your wireless network. Select the setting appropriate for your environment.
If you are not sure which setting to choose, then keep the default setting, 100%. Click the Next button to
continue or Back to return to the previous page.
Figure 5-12: Wireless Power Management Screen
Chapter 5: Setting Up the Wireless-G Access Point with Power Over Ethernet
Setup Wizard
17
Wireless-G Access Point with Power Over Ethernet
13. On the Confirmation screen, make sure your new settings for the Main SSID are correct. Click the SSID1 and
SSID2 radio buttons to view their settings. To save your new settings, click the Yes button. If you do not want
to save your changes, then click the No button.
Figure 5-13: Confirmation Screen
14. At this point, the configuration performed with the Setup Wizard is complete. To configure any other Access
Points in your network, you can run this Setup Wizard again.
Click the Online Registration button to register the Access Point, or click the Exit button to exit the Setup
Wizard.
For more advanced configuration, you can go to “Chapter 6: Configuring the Wireless-G Access Point
with Power Over Ethernet.”
Figure 5-14: Congratulations Screen
Chapter 5: Setting Up the Wireless-G Access Point with Power Over Ethernet
Setup Wizard
18
Wireless-G Access Point with Power Over Ethernet
Chapter 6: Configuring the Wireless-G Access Point with
Power Over Ethernet
Overview
The Access Point has been designed to be functional right out of the box, with the default settings in the Setup
Wizard. However, if you'd like to change these settings, the Access Point can be configured through your web
browser with the Web-based Utility. This chapter explains how to use the Utility.
The Utility can be accessed via Microsoft Internet Explorer or Netscape Navigator through use of a computer that
is networked with the Access Point.
For a basic network setup, most users only have to use the following screens of the Utility:
• Setup
On the Setup screen, enter your basic network settings here.
• Management
Click the Administration tab and then select the Management screen. The Access Point’s default password
is admin. To secure the Access Point, change the AP Password from its default.
HAVE YOU: Enabled TCP/IP on your PCs? PCs
communicate over the network with this
protocol. Refer to “Appendix D: Windows Help”
for more information on TCP/IP.
tcp/ip: a set of instructions PCs use to
communicate over a network.
browser: an application that provides a way to
look at and interact with all the information on the
World Wide Web.
NOTE: The Access Point is designed to
function properly after using the Setup Wizard.
This chapter is provided solely for those who
wish to perform more advanced configuration
or monitoring.
Navigating the Utility
There are five main tabs: Setup, Wireless, AP Mode, Administration, and Status. Additional screens will be
available from most of the main tabs.
Setup
Enter the settings for the Access Point and your Internet connection on this screen.
Wireless
You will use the Wireless tabs to enter a variety of wireless settings for the Access Point.
• Basic Wireless Settings. Enter the network mode, Virtual Local Area Network (VLAN) settings, SSIDs, and
other settings on this screen.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
Overview
19
Wireless-G Access Point with Power Over Ethernet
• Wireless Security. Use this screen to configure the Access Point’s security settings.
• Wireless Network Access. From this screen, you can permit or block access to your wireless network.
• Advanced Wireless Settings. Use this screen to configure the Access Point’s more advanced wireless
settings.
AP Mode
Use this screen to configure how the Access Point will work with other access points in your network.
Administration
You will use the Administration tabs to manage the Access Point.
• Management. This screen allows you to customize the password and Simple Network Management Protocol
(SNMP) settings.
snmp: the standard e-mail protocol on the Internet.
• Log. Configure the Log settings for the Access Point on this screen.
• Factory Default. Use this screen to reset the Access Point to its factory default settings.
• Firmware Upgrade. Upgrade the Access Point’s firmware on this screen.
firmware: the programming code that runs a
networking device.
• Language Upgrade. On this screen, change the language of the Access Point’s Web-based Utility.
• Reboot. Use this screen to reboot the Access Point.
• Config Management. You can back up the configuration file for the Access Point, as well as save the backup
configuration file to the Access Point.
Status
You will be able to view status information for your local network, wireless networks, and network performance.
• Local Network. This screen will display current information on the Access Point and its local network.
• Wireless. This screen will display current information on the Access Point and its wireless networks.
• System Performance. This screen will display current information on the Access Point and its data
transmissions.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
Navigating the Utility
20
Wireless-G Access Point with Power Over Ethernet
Accessing the Utility
To access the Web-based Utility of the Access Point, launch Internet Explorer or Netscape Navigator, and enter
the Access Point’s default IP address, 192.168.1.245, in the Address field. Press the Enter key.
Open your web browser and type the IP address you entered in the Setup Wizard. (The default IP address is
192.168.1.245.) (Should you need to learn what IP address the Access Point presently uses, run the Setup
Wizard again. It will scan the Access Point and give you its IP address.) Press the Enter key and the following
screen will appear. Enter admin in the User Name field. The first time you open the Web-based Utility, use the
default password, admin. (You can set a new password from the Administration - Management tab.) Then click
the OK button.
Figure 6-1: Login Screen
The Setup Tab
The first screen that appears is the Setup screen. This allows you to change the Access Point's general settings.
Setup
Enter the Host and Device Names for the Access Point.
Host Name. You may assign any Host Name to the Access Point. Unique, memorable names are helpful,
especially if you are employing multiple access points on the same network.
Device Name. You may assign any Device Name to the Access Point. Unique, memorable names are helpful,
especially if you are employing multiple access points on the same network.
Network Setup
The selections under this heading allow you to configure the Access Point’s IP setting(s).
IP Settings
Select Automatic Configuration - DHCP if your network router will assign an IP address to the Access Point.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
Accessing the Utility
Figure 6-2: Setup - Automatic Configuration DHCP Screen
21
Wireless-G Access Point with Power Over Ethernet
Select Static IP Address if you want to assign a static or fixed IP address to the Access Point. Then complete the
following:
• IP Address. The IP address must be unique to your network. We suggest you use the default IP address of
192.168.1.245.
• Subnet Mask. The Subnet Mask must be the same as that set on your Ethernet network.
• Default Gateway. Enter the IP address of your network’s gateway. The gateway is the device that enables
communication between your computers and the Internet. In most cases, your router acts as your gateway.
• Primary and Secondary DNS. Enter the IP address of your Domain Name System (DNS) server. This
information should be provided by your ISP. You should enter at least one DNS address.
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Click Help for more information.
Figure 6-3: Setup - Static IP Address Screen
static ip address: a fixed address assigned to a computer or
device that is connected to a network.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Setup Tab
22
Wireless-G Access Point with Power Over Ethernet
The Wireless - Basic Wireless Settings Tab
Change the wireless network settings on this screen. The Access Point can connect to up to eight wireless
networks at the same time.
Wireless Network
Configure the Access Point using the available settings. You can enter and save more than one configuration for
the Access Point because the Access Point can work with a primary wireless network and up to seven Virtual
Local Area Networks (VLANs).
NOTE: To use the Access Point’s VLAN features, you must have a managed switch.
Wireless Network Mode. Select Mixed and both Wireless-G and Wireless-B computers will be allowed on the
network, but the speed will be reduced. Select G-Only for maximum speed with Wireless-G products only. The
final selection, B-Only, allows only Wireless-B products on the network. You can also disable wireless
performance if you select Disabled.
VLAN Trunk. Select Enabled if you want to use the Access Point’s VLAN features.
Figure 6-4: Wireless - Basic Wireless Settings Screen
Priority. Select Enabled if you want to use the Access Point’s capability to assign VLAN priorities. Select
Disabled if you want to disable the Access Point’s capability to assign VLAN priorities.
Main SSID. Enter settings for the Access Point’s primary wireless network.
Virtual SSID1-7. You can enter settings for up to seven virtual wireless networks.
SSID Name. The SSID is the unique name shared among all devices in a wireless network. It is case-sensitive
and must not exceed 32 alphanumeric characters, which may be any keyboard character. Make sure this setting
is the same for all devices in each wireless network.
VLAN ID. Enter the ID number you want to assign to this VLAN. Make sure at least one of these matches the
Access Point VLAN ID entered on this screen.
Priority. You can assign VLAN priority to each wireless network, Low, Medium, or High.
TX Rate Limitation. The default setting is 54 Mbps. The range is from 1 to 54Mbps. The rate of data
transmission should be set depending on the speed of your wireless network. You can select from a range of
transmission speeds, or you can keep the default setting, 54 Mbps, to have the Access Point enable the AutoChapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Wireless - Basic Wireless Settings Tab
23
Wireless-G Access Point with Power Over Ethernet
Fallback feature. Auto-Fallback will automatically negotiate the best possible connection speed between the
Access Point and a wireless device.
Access Point VLAN ID. Enter the VLAN ID of the Access Point. Make sure this matches at least one of the VLAN
IDs listed in the aforementioned table.
NOTE: You must use the Access Point VLAN ID for one of your wireless networks in order to
maintain access to the Access Point’s Web-based Utility.
Wireless Channel. Select the appropriate channel from the list provided; this will be the channel that all of your
wireless devices will use.
Wireless SSID Broadcast. This feature allows the main SSID to be broadcast by the Access Point. You may want
to enable this function while configuring your network, but make sure that you disable it when you are finished.
With this enabled, someone could easily obtain the SSID information with site survey software and gain
unauthorized access to your main network. Click Enabled to broadcast the main SSID to all wireless devices in
range. Click Disabled to increase network security and block the main SSID from being seen on networked PCs.
NOTE: Only the main SSID of the Access Point can be broadcast. The Access Point cannot
broadcast any of its Virtual SSIDs.
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Click Help for more information.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Wireless - Basic Wireless Settings Tab
24
Wireless-G Access Point with Power Over Ethernet
The Wireless - Wireless Security Tab
Change the Access Point’s wireless security settings on this screen.
Wireless Security
Enter the security settings for each SSID of the Access Point.
Select SSID. Select the SSID whose security settings you want to configure.
Security Mode. Select the security method you want to use, WPA-Personal, WPA-Enterprise, RADIUS, or WEP.
(WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption. WEP stands
for Wired Equivalent Privacy, while RADIUS stands for Remote Authentication Dial-In User Service.) Refer to the
appropriate instructions below. For detailed instructions on configuring wireless security for the Access Point,
turn to “Appendix B: Wireless Security.” To disable such security, select Disable.
WPA-Personal
Allow PCs with the same wireless network name (SSID) to see each other. When enabled, devices in the
same wireless network will be able to access each other, so they can transfer files through the network. To deny
access, select Disabled. Otherwise, keep the default, Enabled.
Figure 6-5: Wireless - Wireless Security
(WPA-Personal) Screen
WPA Algorithms. WPA offers you two encryption methods, TKIP and AES, with dynamic encryption keys. Select
the type of algorithm you want to use, TKIP or AES.
encryption: encoding data transmitted in a network.
WPA Shared Key. Enter a WPA Shared Key of 8-32 characters.
Key Renewal Timeout. Enter a Key Renewal Timeout period, which instructs the Access Point how often it
should change the encryption keys.
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Click Help for more information.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Wireless - Wireless Security Tab
25
Wireless-G Access Point with Power Over Ethernet
WPA-Enterprise
This option features WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS
server is connected to the Access Point.)
Allow PCs with the same wireless network name (SSID) to see each other. When enabled, devices in the
same wireless network will be able to access each other, so they can transfer files through the network. To deny
access, select Disabled. Otherwise, keep the default, Enabled.
RADIUS Server IP Address. Enter the RADIUS server’s IP address.
WPA Algorithms. WPA offers you two encryption methods, TKIP and AES, with dynamic encryption keys. Select
the type of algorithm you want to use, TKIP or AES.
RADIUS Server Port. Enter the port number used by the RADIUS server.
Shared Secret. Enter the Shared Secret key used by the Access Point and RADIUS server.
Key Renewal Timeout. Enter a Key Renewal Timeout period, which instructs the Access Point how often it
should change the encryption keys.
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Click Help for more information.
Figure 6-6: Wireless Security - WPA-Enterprise Screen
radius: a protocol that uses an authentication server to
control network access.
server: any computer whose function in a network is to
provide user access to files, printing, communications, and
other services.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Wireless - Wireless Security Tab
26
Wireless-G Access Point with Power Over Ethernet
RADIUS
This option features WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS
server is connected to the Access Point.)
Allow PCs with the same wireless network name (SSID) to see each other. When enabled, devices in the
same wireless network will be able to access each other, so they can transfer files through the network. To deny
access, select Disabled. Otherwise, keep the default, Enabled.
RADIUS Server IP Address. Enter the RADIUS server’s IP address.
RADIUS Server Port. Enter the port number used by the RADIUS server.
Shared Secret. Enter the Shared Secret key used by the Access Point and RADIUS server.
Default Transmit Key. Select a Default Transmit Key (choose which Key to use).
WEP Encryption. Select a level of WEP encryption, 64 bits (10 hex digits) or 128 bits (26 hex digits).
Passphrase. To generate WEP keys using a Passphrase, then enter the Passphrase and click the Generate key.
Figure 6-7: Wireless Security - RADIUS Screen
Key 1-4. If you want to manually enter WEP keys, then complete the fields provided. Each WEP key can consist of
the letters “A” through “F” and the numbers “0” through “9”. It should be 10 characters in length for 64-bit
encryption or 26 characters in length for 128-bit encryption.
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Click Help for more information.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Wireless - Wireless Security Tab
27
Wireless-G Access Point with Power Over Ethernet
WEP
Authentication Type. Select the authentication method you want the Access Point to use, Shared Key or Open
System. Shared Key is when both the sender and the recipient share a WEP key for authentication. Open System
is when the sender and the recipient do not share a WEP key for authentication. All devices on your network must
use the same authentication type.
Allow PCs with the same wireless network name (SSID) to see each other. When enabled, devices in the
same wireless network will be able to access each other, so they can transfer files through the network. To deny
access, select Disabled. Otherwise, keep the default, Enabled.
Default Transmit Key. Select a Default Transmit Key (choose which Key to use).
WEP Encryption. Select a level of WEP encryption, 64 bits (10 hex digits) or 128 bits (26 hex digits).
Passphrase. To generate WEP keys using a Passphrase, then enter the Passphrase and click the Generate key.
Key 1-4. If you want to manually enter WEP keys, then complete the fields provided. Each WEP key can consist of
the letters “A” through “F” and the numbers “0” through “9”. It should be 10 characters in length for 64-bit
encryption or 26 characters in length for 128-bit encryption.
Figure 6-8: Wireless Security - WEP Screen
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Click Help for more information.
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Wireless - Wireless Security Tab
28
Wireless-G Access Point with Power Over Ethernet
The Wireless - Wireless Network Access Tab
This screen allows you to permit or block wireless access for computers with specific MAC addresses.
Wireless Network Access
You can allow or block access for the MAC addresses you have entered.
Access List. To permit access, click Permit to access. To deny access, click Prevent from accessing. If you do
not wish to filter users by MAC address, select Disabled.
MAC 1-20. Enter the MAC addresses of the computers whose access you want to control.
Select MAC Address from Networked Computers. If you want to select a MAC address from a list, click this
button. The MAC addresses for your computers will be automatically displayed. Click the checkboxes of the MAC
addresses you want to add to your access list. Change these settings as described here and click Apply to apply
your changes. Click Refresh to retrieve the latest MAC addresses. Click Close to close this screen and return to
the Wireless Network Access screen.
Change these settings as described here and click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes. Click Help for more information.
Figure 6-9: Wireless - Wireless Network Access Screen
mac address: the unique address that a manufacturer
assigns to each networking device.
Figure 6-10: Select MAC Address Screen
Chapter 6: Configuring the Wireless-G Access Point with Power Over Ethernet
The Wireless - Wireless Network Access Tab
29

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2005:05:04 18:28:39+08:00
Create Date                     : 2005:05:04 18:28:17+08:00
Title                           : Book Template.book
Author                          : junelee
Creator                         : FrameMaker 7.0
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Page Count                      : 14
Mod Date                        : 2005:05:04 18:28:39+08:00
Creation Date                   : 2005:05:04 18:28:17+08:00
Metadata Date                   : 2005:05:04 18:28:39+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools