LINKSYS WPS54GV2 Wireless-G Print Server User Manual Book
LINKSYS LLC Wireless-G Print Server Book
LINKSYS >
Contents
- 1. Manual 1
- 2. Manual 2
Manual 2
34
Chapter 6: Configuring the PrintServer Using the Web-based Utility
The Printer Tab - Logical Port
Wireless-G PrintServer
The Printer Tab - Logical Port
The Logical Printers tab contains the logical printer settings of the PrintServer. Configure them for each Logical
Printer.
The PrintServer has three logical or virtual printer ports. For example, you can have three different configurations
for your USB printer: Logical Printer 1 for landscape orientation, Logical Printer 2 for double-sided copies, and
Logical Printer 3 for manual feed. Then you will map Logical Printers 1, 2, and 3 to the physical printer on the
PrintServer’s USB port.
Select Printer
Logical Printer No. From the Logical Printer Port No: drop-down menu, select the number (1-3) of the printer you
wish to configure. Click the Get Data button to update the display with the current data for the selected logical
printer.
Details
Pre-string (Hex). Enter the printer control string (in hexadecimal characters) to be sent to the printer before each
print job. This string cannot exceed 30 characters.
Post String (Hex). Enter the printer control string (in hexadecimal characters) to be sent to the printer after each
print job. This string cannot exceed 30 characters.
Convert LF to CR+LF. If checked, LF (line feed) characters are changed to CR+LF (carriage return + line feed).
Click the Save button to apply your changes, or click Cancel to cancel your changes.
Figure 6-10: Printer - Logical Port
35
Chapter 6: Configuring the PrintServer Using the Web-based Utility
The Status Tab - Device
Wireless-G PrintServer
The Status Tab - Device
The Device tab allows you to view information about the PrintServer.
Server Details
The PrintServer’s settings and status information are displayed here. No values can be changed on this screen.
This screen is for information only.
Upgrade. If you want to upgrade the PrintServer’s firmware, follow these instructions:
1. Visit www.linksys.com and download the firmware upgrade file for the Wireless-G PrintServer.
2. Extract the file on your computer.
3. On the Device screen, click the Upgrade button.
4. On the Firmware Upgrade screen, enter the location of the extracted firmware file, or click the Browse button
to find this file.
5. Click the Start Upgrade button, and follow the on-screen instructions.
On the Device screen, click the Refresh button to retrieve this information again.
Figure 6-11: Status Tab - Device
download: to receive a file transmitted over a network
firmware: the programming code
that runs a networking device
upgrade: to replace existing software or
firmware with a newer version
Figure 6-12: Firmware Upgrade
36
Chapter 6: Configuring the PrintServer Using the Web-based Utility
The Status Tab - Printer
Wireless-G PrintServer
The Status Tab - Printer
The Printer tab allows you to view information about the Printers. No values can be changed on this screen. This
screen is for information only.
Port 1 (USB Port)
The port’s status information is displayed here. No values can be changed on this screen. This screen is for
information only.
Print Test Page. Click the Print Test Page button to print a test page on the connected printer.
Clicking the Refresh button causes the PrintServer to retrieve the status information again.
The Status Tab - Wireless
The Wireless tab allows you to view information about the PrintServer’s wireless connection. No values can be
changed on this screen. This screen is for information only.
Link Info
Settings and current transmission rate for the wireless connection are displayed here.
Throughput
The throughput information for the wireless connection is displayed here.
Clicking the Refresh button causes the PrintServer to retrieve information about the wireless connection again.
The Exit Tab
This tab is used exclusively for exiting the Web-based Utility.
Select the Exit tab, and a new screen will appear. Click the Yes button to exit the Utility, or click No to continue
using the Utility.
Figure 6-14: Status Tab - Wireless
Figure 6-15: Exit
Figure 6-13: Status Tab - Printer
37
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
Overview
Chapter 7: Bi-Admin Management
Overview
If you use Windows, then you can manage the PrintServer using its web-based utility (see “Chapter 6:
Configuring the PrintServer Using the Web-based Utility”) or an advanced utility program called Bi-Admin. (If you
use a Macintosh or other non-Windows operating system, you can manage the PrintServer only by using its web-
based utility.)
Bi-Admin is provided on the PrintServer’s Setup CD-ROM and is fully compatible with Windows 98, Me, 2000, and
XP. It allows you to change the PrintServer’s internal settings, check on the unit’s status, and perform basic
diagnostic tests. Note that the Bi-Admin program must be installed only on the network administrator’s computer.
First, install Bi-Admin on your computer. Then, you will be able to use the management utility.
Bi-Admin Installation
1. Make sure you have no programs or applications running on your computer.
2. If you haven’t already done so, insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup CD-
ROM should run automatically. Click Exit to exit the Setup Wizard.
3. Then click the Start button and choose Run. In the box that appears, enter D:\Utility\Setup.exe (if “D” is the
letter of your CD-ROM drive).
4. The Welcome screen of the Bi-Admin Setup program will appear first. Click Next to continue with the Bi-
Admin installation, or click Cancel to quit the setup program, and then close the open programs.
Figure 7-1: Bi-Admin Setup Welcome
38
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
Bi-Admin Installation
5. The Choose Destination Location screen will appear. Choose the location where the B-Admin folder will be
installed. To install the driver in the default location, click Next. If you want the folder to be installed in a
different location, click the Browse button and select the location. Then click Next.
Click Back to return to the previous screen. Click Cancel to end the Bi-Admin installation.
6. The Select Program Folder screen will appear. An icon will be added to the program folder listed. You may
change the name for the program folder, if you wish. Click Next.
Click Back to return to the previous screen. Click Cancel to end the Bi-Admin installation.
7. When the Bi-Admin is installed, the Setup Complete screen will appear. Click Finish.
Figure 7-3: Select Program Folder
Figure 7-2: Choose Destination Location
39
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
Starting the Bi-Admin Management Utility
Starting the Bi-Admin Management Utility
1. To start the Bi-Admin program, click Start, Programs, Print Server Utility, and then Bi-Admin
Management Utility. If the Bi-Admin Management Utility icon has been created, you can just double-click it
instead. You can drag the shortcut icon onto your Desktop for easy access to the Bi-Admin Management
Utility.
2. When the Bi-Admin Management Utility appears, it will ask for the Connected Protocol. Make sure the box
next to TCP/IP is checked. Click the OK button.
3. The Bi-Admin Management Utility will automatically scan the network for the PrintServer.
Figure 7-5: Searching for Device
Figure 7-4: Connected Protocol
40
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
The Bi-Admin Management Utility
The Bi-Admin Management Utility screen will appear next. Any hardware found on the network will appear on the
left-hand side of the screen. The Utility can be managed from this screen. The menu and icon options will be
explained in this section.
Menu Options
Main. The options are Device Status, Printer Status, Configure, Upgrade, Refresh, and Exit. These options are the
same as the icons that are displayed below the menu options (viewed from left to right), and are described below:
•Device Status. This option allows you to view all of the device settings, optionally save the device settings to
a file, or restore a previously saved file to the device.
If you click Device Status, the Device Information screen will appear. A list of the PrintServer’s device
settings is displayed, including Hardware ID, Firmware version, Protocol ID, Default Name, Server Name, and
MAC Address. To save the information in a .txt (text) file, click the Save to file button.
To choose a different device that you configured, click the Open button. You may then browse for your file,
select it, and then click Open. The contents of the file will display on the right-hand side of the screen. To
save the file to the PrintServer, click Restore to Device.
Click the Exit button to return to the Bi-Admin Management Utility screen. For more information, click the
Help button.
Figure 7-6: Bi-Admin Management Utility
Figure 7-7: Device Information
41
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
•Printer Status. This option allows you to view the printer status, as well as set port and printer parameters.
If you click Printer Status, the Printer Status screen will appear. The Device Name will be displayed and the
Current Selected Port will be highlighted. The status information for this port will be displayed.
Click the Back button to return to the Bi-Admin Management Utility screen. Click Refresh to refresh the
screen. For more information, click the Help button.
If the printer is bi-directional and not busy, the Printer Configuration button will appear on the Printer Status
screen. Click this button to view the printer’s Environmental Variable and Variable Value items. If the items
are not read-only, you can change them based on the options of your printer.
For more information, click the Help button.
Figure 7-8: Printer Status
42
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
•Configure. You may configure the PrintServer with this option.
If you click Configure, the Configuration screen will appear. It displays eight tabs: System, TCP/IP, AppleTalk,
NetBEUI, Internet Printing, Port, Wireless, and SNMP. The tabs will be described below.
System
•Device Name. Enter the Device Name in the field provided.
•Comment. Enter any comments in the Comment field.
•Device Password. To change the password, select Change Device Password, enter the new password
in the Password field, and then re-enter the password in the Confirm Password field.
•Protocol. Select the protocol you want to use for your network: TCP/IP, AppleTalk, NetBEUI, IPX/SPX.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button.
Figure 7-9: Configuration - System
43
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
TCP/IP
•Dynamic IP Address (DHCP). If your network router is using DHCP to assign IP addresses, select
Dynamic IP Address (DHCP). By default, Dynamic IP Address (DHCP) is enabled.
•Fixed IP Address. If you need to assign the PrintServer a fixed IP address (also known as static IP
address), select Fixed IP Address, and enter the appropriate values under IP Address, Subnet Mask, and
Gateway. Make sure the IP Address and Subnet Mask are appropriate for your network. If you change the
PrintServer’s IP address, make sure you that you reconnect to the PrintServer using that new IP address.
Otherwise, you will not be communicating with the PrintServer. In most cases, the Gateway IP address is
the IP address of your router, and you should complete the Gateway field if you will use the PrintServer for
Internet printing. (To find out your router’s IP address, consult your router’s documentation.)
•TCP session. If your TCP session has ended, you can attempt a new connection. In the Retry interval field,
enter how often you want the PrintServer to attempt a connection. In the Retry count field, enter the
maximum number of attempts.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button.
Figure 7-10: Configuration - TCP/IP
44
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
Apple Talk
•Zone Name. Typically only Macintoshes use AppleTalk, although other platforms can use it if they have
the necessary, third-party software installed. Enter the Zone Name in the field provided.
•Port Setting. Select the port number from the drop-down menu. The Printer Type can be obtained from
the manufacturer of the printer. Enter the type of printer in the Printer Type field. For each printer
connected to the PrintServer, you will choose the Communications Protocol that allows the devices on the
network to communicate. Select the type of Communication Protocol you will use, ASCII or Binary for
each printer, according to the recommendation of the printer’s manufacturer. For more information, refer
to the printer’s documentation.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button.
Figure 7-11: Configuration - AppleTalk
45
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
NetBEUI
•Domain Name
. Enter the name of the domain that you want the PrintServer associated with in the Domain
Name field. If you are unsure of the Domain Name, you can find it out by looking on any computer already on
the network. In Windows 98, right-click
Network Neighborhood
and select
Properties
. Under the
Identification tab, there will be listed that computer’s name, and the Domain to which it is connected. For
Windows Me, 2000, or XP, right-click
My Network Places
. In Windows Me, choose
Properties
from the
menu that appears. In Windows 2000 or XP, choose
Properties
from the menu that appears. Then, right-
click
Local Area Connection
and choose
Properties
. The Domain name will appear. If you want the
PrintServer to be connected to that same Domain, enter that Domain name here. If no Domain name exists
there, you will use the Workgroup name from that window.
•
Port Setting
. You can specify the Response Time that you prefer for the PrintServer. This is the amount of
time (measured in seconds) that the PrintServer will wait for a response from the network before “timing
out.” You also have the option to use this feature, Abort Print Job if Error. Selecting Yes here will terminate
the printing if there is an error of any kind. If you select No, print jobs that have errors will be sent to the
printer, but might not print properly.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button.
Figure 7-12: Configuration - NetBEUI
46
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
Internet Printing
•Mail Server. Enter the address of your mail server in the Mail Server IP Address fields. (This value must
be a fixed IP address.) Enter the Mail Account name and Password next. Enter the password again in the
Confirm Password field. Then, enter the time interval for the PrintServer to check for e-mail to be printed,
in hours and minutes in the Check Mail Interval field. You may also specify an e-mail address to which
mails that cannot be printed are routed; this is useful for both graphic-intensive e-mails and for
troubleshooting purposes. Enter this e-mail address in the Redirect Mail Account field.
•Printer. Select the Default Printer Port from the drop-down menu. In the field provided, enter the Printer
Model, which can be found through the Device Manager.
•Options. Place a check mark next to the options you want to enable: Print Every Mail, Banner Printing
(enabled by default), or Mail response when Printed.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button.
Figure 7-13: Configuration - Internet Printing
47
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
Port
•Physical Port. Select the number of the Selected Physical Port from the drop-down menu. Select the
Handshake Signal, Busy Only or Busy & Ack. Select the Printer Type, High Speed or Low Speed.
•Logical Port. Select the Selected Logical Port from the drop-down menu and then the physical port you
want to map it to from the drop-down menu for Map to Physical Port. If you select Yes for Convert LF to
LF+CR, the LF (line feed) characters are changed to LF+CR (line feed + carriage return). In the field for
Prefix of Job, enter the printer control string (in hexadecimal characters) to be sent to the printer before
each print job. This string cannot exceed 30 characters. In the field for Suffix of Job, enter the printer
control string (in hexadecimal characters) to be sent to the printer after each print job. This string cannot
exceed 30 characters.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button.
Figure 7-14: Configuration - Port
48
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
Wireless
•SSID (Service Set Identifier). In the SSID field, enter the name of your wireless network. This is the
unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32
characters or fewer.
•Channel No. If your network is set to ad-hoc mode, select your network’s channel setting from the
Channel No. drop-down menu.
•Network Type. The Network Type setting shows a choice of two wireless modes. Select Infrastructure if
you want the PrintServer to communicate using an access point or wireless router. Select Ad-Hoc if you
want the PrintServer to communicate without using an access point or wireless router.
•WEP Encryption. If you want to enable WEP encryption for greater wireless security, click the Enable
radio button. If you want to disable WEP encryption, keep the default, Disable. From the WEP
Authentication drop-down menu, select your wireless network’s authentication type. The default is set to
Open System, for which the sender and the recipient do NOT use a WEP key for authentication. You can
also choose Shared Key, when the sender and recipient use a WEP key for authentication. This setting
should match the one on your network’s access point or wireless router.
In the WEP Keys section, select the level of WEP encryption, 64 bits or 128-bits. From the drop-down
menu, select the Default Key used by your wireless network. This indicates which WEP key your network
uses for WEP encryption. In the Key1 (hex) to Key4 (hex) fields, enter your network’s WEP keys. If you
are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you
are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid
hexadecimal characters are “0”-“9” and “A”-“F”.
Click the Link Info button if you want to view information about the wireless connection.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button.
Figure 7-15: Configuration - Wireless
49
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
SNMP
•SysContact. Enter the name of the contact person in the SysContact field.
•SysLocation. Enter the location of the contact person in the SysLocation field.
•Configuration Item. From the Configuration Item box, select the number of the management station (M1-
M4) or trap receiver (T1-T4). The selected item’s information will be displayed below.
For management stations, you can change the station’s IP address, Community String, and Access
Permission level. In the Manager IP Address fields, enter the IP address of the management station with
the SNMP program installed. In the Community String field, enter the name of the SNMP community,
which is usually public or private. In the Access Permission section, select the desired level of access for
this management station, Read Only, Read/Write, or Not Accessible.
For trap receivers, you can change the trap receiver’s IP address, Community String, Trap Option, and
Trap Severity level. In the Trap Receive IP Address fields, enter the IP address of the trap receiver that will
be sent the trap messages or notifications. In the Community String field, enter the name of the SNMP
community, which is usually public or private. For the Trap Option setting, select Enable or Disable. For
the Trap Severity setting, select the desired level of severity, with 1 meaning least severe.
Click the Get Defaults button if you want to cancel your changes and use the default settings.
When finished making your changes on this tab, click the OK button to save these changes, or click the
Cancel button to undo your changes. For more information, click the Help button. Figure 7-16: Configuration - SNMP
50
Wireless-G PrintServer
Chapter 7: Bi-Admin Management
The Bi-Admin Management Utility
•Upgrade. You may use this option to upgrade the firmware of the PrintServer. Follow these instructions:
1. On the Upgrade screen, click the Files button.
2. The Detected LAN Cards screen will appear. Select the LAN card the PrintServer is connected to, and then
click the OK button.
3. Follow the on-screen instructions, and select the firmware file you want to use.
4. View the BIN File Information screen, and click the OK button if you have selected the correct firmware
file. Click the Cancel button to select a different firmware file.
5. On the Upgrade screen, click the Upgrade button. Click the Cancel button to cancel the firmware
upgrade. For more information, click the Help button.
•Refresh. This option allows you to refresh the device list after you change the name or IP address of a device.
The screen does not refresh automatically.
•Exit. This option allows you to exit the Bi-Admin program.
InitDevice. The available options are Reset Device, Restore to Factory Default, Attached Remote, and Connected
Protocol.
If you click Attached Remote, the Add Cross Segment Printer screen appears. To add a cross segment print
server, enter its IP address in the fields provided, and click the Set button.
Click Cancel to undo any changes. For more information, click the Help button.
Diagnostic. Diagnostic allows you to print a test page from either of the PrintServer’s ports.
Help. The two options are Help Topics and About Bi-Admin. These help files offer extensive advice and details
about all of the PrintServer’s functions and capabilities.
Figure 7-18: Detected LAN Cards
Figure 7-19: BIN File Information
Figure 7-20: Add Cross Segment PrintServer
Figure 7-17: Upgrade
51
Chapter 8: Internet Printing Protocol (IPP)
Overview
Wireless-G PrintServer
Chapter 8: Internet Printing Protocol (IPP)
Overview
Internet Printing Protocol (IPP) is a standards-based system that allows remote printing from a PC to any
accessible printer. Normally, the printer will be attached to a computer or other device that functions as an IPP
Server. For client PCs, it is necessary to install a compatible IPP Client program. The Client must also know the IP
Address or URL of the IPP Server.
The PrintServer contains the necessary firmware to act as an IPP Server. No additional configuration is
necessary. However, the following requirements must be met:
• The PrintServer must have a valid IP Address. For printing via the Internet, the PrintServer’s IP Address must
be external (allocated by your ISP), rather than an IP Address on your local LAN.
• Any Router, Gateway, or Firewall linking your LAN to the Internet must NOT block IPP. (IPP uses Port Services
631/TCP.)
• You must advise clients of the correct URL or IP Address of the IPP Server. To use a URL rather than an IP
Address, you need to register the domain name for the URL.
• Unless clients are using Windows 2000 or XP, you must provide your clients with the supplied IPP Client
software. If it is not convenient to provide the CD-ROM, supply the setup.exe file, located in the IPP folder.
Windows IPP Client Setup
Installing using setup.exe
1. Run this program, located at d:\driver\ipp\setup.exe, to unzip the included files.
2. The IPP Setup program will then run.
3. Follow the prompts to complete the installation.
52
Chapter 8: Internet Printing Protocol (IPP)
Windows IPP Client Setup
Wireless-G PrintServer
IPP Client Configuration for Windows 98, Me, 2000, and XP
1. Run the Add IPP Port program entry created by the installation.
2. On the Output Select screen, enter the IP Address or URL of the IPP Server.
3. If Internet access from your location is via a Proxy Server, check Access IPP Server via Proxy Server, and
enter details of your Proxy Server. (This will be the same as your browser configuration.)
4. Click Select Device Port to view the available ports on the IPP Server, and select the appropriate port. A
connection to the IPP Server will be established at this time.
5. Click OK to create the IPP port on your system. You will see a message confirming that the port has been
created, and then you will see the AddPort screen.
6. Perform one of these steps.
Select an existing printer to use the new port, and click OK.
OR
Click the Add New Printer button to create a new printer that will use the IPP port. This will start the Add
Printer Wizard. Follow the prompts to complete the process. Make sure that the new printer uses the IPP port.
Installation is now complete.
• To create additional IPP ports, repeat the entire procedure.
• The Proxy Server and other options are set individually for each IPP port.
53
Chapter 8: Internet Printing Protocol (IPP)
Windows IPP Client Setup
Wireless-G PrintServer
Changing the IPP Port Settings
After the IPP port is created, you can reach the Configure IPP Port screen by performing these steps:
1. Open the Printers folder (Start => Settings => Printers).
2. Right-click IPP Printer and select Properties.
3. Click the Port Settings or Configure Port button (Details or Port tab, depending on your version of Windows).
The Configure IPP Port screen will appear.
There are two settings, Retry Interval and Retry Count, which can be adjusted if you have problems connecting to
the IPP Server.
• The Retry Interval sets the time interval (in seconds) between connection attempts. Increase this number if
you have a poor connection, or the remote server is very busy.
• The Retry Count sets how many connection attempts will be made. Increase this number if you have a poor
connection, or the remote server is very busy.
IPP Client Setup for Windows XP
Windows XP has its own IPP Client, and there is no need to install the supplied IPP Client Software. To use this IPP
Client with the PrintServer, follow this procedure:
1. Click the Start button.
2. Select Settings and click Printers and Faxes.
3. Click Add a printer.
4. On the Welcome to the Add Printer Wizard screen, click the Next button.
5. On the Local or Network Printer screen, select A network printer, or a printer attached to another
computer, and click the Next button.
Figure 8-1: Windows XP - Local or Network Printer
54
Chapter 8: Internet Printing Protocol (IPP)
Windows IPP Client Setup
Wireless-G PrintServer
6. On the Specify a Printer screen, select Connect to a printer on the Internet or on a home or office
network, and enter the URL of the IPP Server as follows (ip_address represents the IP Address of the IPP
Server, and 631 represents the port number).
Port 1 ip_address:631/ipp/P1
7. If the connection can be established, and the printer on that port is online, the Connect to Printer dialog box
will be displayed. This screen notifies you that the printer driver is not installed. Click the OK button.
8. Select the printer manufacturer and model to match the printer connected to the appropriate port on the IPP
Server.
9. Click the OK button and follow the prompts to complete the Wizard.
The IPP printer is now ready for use.
IPP Client Setup for Windows 2000
Windows 2000 has its own IPP Client, and there is no need to install the supplied IPP Client Software. To use this
IPP Client with the PrintServer, follow this procedure:
1. Click the Start button.
2. Select Settings and click Printers.
3. Double-click Add Printer.
4. On the Welcome to the Add Printer Wizard screen, click the Next button.
5. Select Network Printer and click Next to see the Locate your Printer screen.
6. Select Connect to a printer on the Internet or on your intranet, and enter the URL of the IPP Server as
follows (ip_address represents the IP Address of the IPP Server, and 631 represents the port number).
Port 1 ip_address:631/ipp/P1
Figure 8-3: Windows 2000 - Locate Your Printer
NOTE: These entries are case-sensitive. They must be entered as shown, with “ipp” in lowercase
and P1 in uppercase.
Figure 8-2: Windows XP - Specify a Printer
NOTE: These entries are case-sensitive. They must be entered as shown, with “ipp” in lowercase
and P1 in uppercase.
55
Chapter 8: Internet Printing Protocol (IPP)
Windows IPP Client Setup
Wireless-G PrintServer
7. If the connection can be established, and the printer on that port is online, the Connect to Printer dialog box
will be displayed. This screen notifies you that the printer driver is not installed. Click the OK button.
8. Select the printer manufacturer and model to match the printer connected to the appropriate port on the IPP
Server.
9. Click the Next button and follow the prompts to complete the Wizard.
The IPP printer is now ready for use.
Using IPP Printers
The IPP Printer can be selected and used like any other Windows printer. If the IPP Server is not on your network,
your Internet connection needs to be active.
If you wish to check the availability of the remote IPP Server, you can use the Query IPP Printer program installed
with the Add IPP Port program.
An IPP Server may be unavailable for any of the following reasons:
• It is powered off.
• A printer problem has caused the IPP Server to cease responding, and a restart (reboot) is required.
• The Server’s IP Address has changed.
• The Internet connection for the IPP Server is down.
• Network congestion causes the connection attempt to time out.
If using the supplied IPP Client software, there are two settings, Retry Interval and Retry Count, which can be
adjusted if you have problems connecting to the IPP Server.
See the previous section, “Changing the IPP Port Settings,” for details.
56
Appendix A: Troubleshooting
Common Problems and Solutions
Wireless-G PrintServer
Appendix A: Troubleshooting
This appendix consists of “Common Problems and Solutions”. Provided are possible solutions to problems that
may occur during the installation and operation of the PrintServer. Read the descriptions below to help you solve
your problems. If you can’t find an answer here, check the Linksys website at www.linksys.com.
Common Problems and Solutions
1. All the LEDs on the front of the PrintServer are not lit.
Check the power adapter and the connection to the electrical outlet.
2. The PrintServer’s Power LED lights up orange or flashes continuously.
Reset the PrintServer. Unplug the power adapter and plug it back in, or press the Reset button on the back of
the PrintServer for approximately ten seconds.
3. I am using DHCP, and the PrintServer gets an IP address conflict involving the PrintServer.
If the PrintServer is left powered on when the DHCP server, which is usually the network router, is powered
off, the PrintServer will retain its IP address without informing the DHCP server. Reset the PrintServer so it will
obtain a new IP address. This problem may also occur if you assigned a static IP address within the range
used by the DHCP server. If so, use another address NOT within the range used by the DHCP server.
4. The PrintServer’s Ethernet LED is not lit.
Check your Ethernet network cable and make sure that the appropriate Ethernet or Link LED on your router or
switch is lit.
5. A printer connected to the PrintServer cannot print or prints garbage.
Do the following:
• Check the cable connection between the PrintServer and printer.
• Make sure the printer driver in the application program or Windows matches the printer.
• Make sure the printer is not too long, less than 10 feet.
6. The Configuration button on the Printer Status screen in Bi-Admin is grayed out, even though my
printer is bi-directional.
The button is unavailable until the printer has finished its print jobs and sits idle.
57
Appendix A: Troubleshooting
Common Problems and Solutions
Wireless-G PrintServer
7. To start over, I need to set the PrintServer to its factory default settings.
Unplug the PrintServer’s power adapter. Press the Reset button while you plug in the PrintServer’s power
adapter. Continue to hold the Reset button for 10 seconds and then release it. This will reset the password,
wireless, and other settings on the PrintServer to the factory defaults. In other words, the PrintServer will
revert to its original factory configuration.
8. I need to upgrade the firmware.
In order to upgrade the firmware with the latest features, follow these steps:
1. Go to the Linksys website at http://www.linksys.com and download the latest firmware for the
PrintServer. Then extract the firmware file on your PC.
2. Open the PrintServer’s Web-based Utility. Click Status and then Device.
3. Click the Upgrade button, and follow the on-screen instructions.
9. I want to manually change my printer’s IP address.
Follow these steps:
1. Click Start, Settings, and Control Panel.
2. Double-click Printers and Faxes.
3. Right-click the printer you want.
4. Click Properties.
5. Click the Ports tab.
6. Select the IP port and click Configure Port.
7. On the Port Settings screen, change the IP address and click the OK button.
58
Appendix B: Wireless Security
Security Precautions
Wireless-G PrintServer
Appendix B: Wireless Security
Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of
Linksys products provide several network security features, but they require specific action on your part for
implementation. So, keep the following in mind whenever you are setting up or using your wireless network.
Security Precautions
The following is a complete list of security precautions to take:
1. Change the default SSID.
2. Disable SSID Broadcast.
3. Change the default password for the Administrator account.
4. Enable MAC Address Filtering.
5. Change the SSID periodically.
6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce
your network performance.
7. Change the WEP encryption keys periodically.
To ensure network security, at least steps one through five should be followed.
Security Threats Facing Wireless Networks
Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking
products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the
network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:
Change the administrator’s password regularly. With every wireless networking device you use, keep in mind
that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only
person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can
change those settings. So, make it harder for a hacker to get that information. Change the administrator’s
password regularly.
Note: Some of these security features are
available only through the network router or
access point. Refer to the router or access
point’s documentation for more information.
59
Appendix B: Wireless Security
Security Threats Facing Wireless Networks
Wireless-G PrintServer
SSID. There are several things to keep in mind about the SSID:
1. Disable Broadcast
2. Make it unique
3. Change it often
Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be
more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast
the SSID.
Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.)
Hackers know these defaults and can check these against your network. Change your SSID to something unique
and not something related to your company or the networking products you use.
Change your SSID regularly so that any hackers who have gained access to your wireless network will have to
start from the beginning in trying to break in.
MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only
those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with
a random MAC Address.
WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security
concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job
more difficult.
There are several ways that WEP can be maximized:
1. Use the highest level of encryption possible
2. Use “Shared Key” authentication
3. Change your WEP key regularly
WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Two modes are
available: Pre-Shared Key and RADIUS. Pre-Shared Key gives you a choice of two encryption methods: TKIP
(Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message
Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption System), which utilizes
a symmetric 128-Bit block data encryption. RADIUS (Remote Authentication Dial-In User Service) utilizes a
RADIUS server for authentication and the use of dynamic TKIP, AES, or WEP.
Important: Always remember that each
device in your wireless network MUST use
the same encryption method and encryption
key or your wireless network will not function
properly.
60
Appendix B: Wireless Security
Security Threats Facing Wireless Networks
Wireless-G PrintServer
WPA Pre-Shared Key. If you do not have a RADIUS server, select the type of algorithm, TKIP or AES, enter a
password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between
0 and 99,999 seconds, which instructs the Router or other device how often it should change the encryption
keys.
WPA RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS
server is connected to the Router or other device.) First, select the type of WPA algorithm, TKIP or AES. Enter
the RADIUS server’s IP Address and port number, along with a key shared between the device and the server.
Last, enter a Group Key Renewal period, which instructs the device how often it should change the encryption
keys.
RADIUS. WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is
connected to the Router or other device.) First, enter the RADIUS server’s IP Address and port number, along
with a key shared between the device and the server. Then, select a WEP key and a level of WEP encryption,
and either generate a WEP key through the Passphrase or enter the WEP key manually.
Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting
sensitive data over your network, encryption should be used.
These security recommendations should help keep your mind at ease while you are enjoying the most flexible
and convenient technology Linksys has to offer.
61
Appendix C: About Bi-Directional Printing
Wireless-G PrintServer
Appendix C: About Bi-Directional Printing
Normal printing only sends print signals from a PC to a printer. Bi-directional printing, also called bitronic printing,
refers to a printer’s ability to do just the opposite—talk back to a PC to notify it of a print job status, paper jams, etc.
This two-way communication technology can be found in HP, IBM, Panasonic, and other laser or color printers where
close contact between the PC and printer is key. In color printing, for example, the printer “informs” the PC of its
constant status in order to mix color inks correctly for optimal quality output.
Bi-directional communication, communication from a printer to a PC, is normally handled by a combination of the
printer hardware and special software on your computer. Using a bi-directional printer on a network poses unique
challenges. Unlike a direct PC-to-printer connection during which a bi-directional printer can easily send its signals
back to the host PC through the computer’s parallel or USB port (which is normally located only a few feet away from
the printer), a networked printer faces the problem of having to route messages bound for a particular PC through a
large array of hubs, switches, file servers, and computers. Unfortunately, most printers are not equipped to handle the
complexities of printer-to-PC communication across a network. That does not mean that they can’t be used on a
network, however.
Linksys designed the PrintServers to function with both regular as well as bi-directional printers. However, the
PrintServer cannot pass messages from the printer back to the printing PC—this limitation is simply an industry
standard, and not one of the PrintServer itself.
However, the PrintServer can check any printer’s online and printing status on the network using the Bi-Admin
management utility software packaged with the PrintServer. The status-checking feature built into the management
software does not require a bi-directional printer to function. If your printer came with special bi-directional software
allowing you to monitor printer status, do not use it with the PrintServer—the software is most likely not network-
capable. For best results, turn off the printer’s bi-directional function either by (1) removing any bi-directional printing
software from your network computers, and/or (2) turning off the printer’s bi-directional print feature inside of the
printer’s on-board menus (if it has menus). Your printer’s user guide should be able to provide specific instructions for
doing this.
62
Appendix D: Upgrading Firmware
Wireless-G PrintServers
Appendix D: Upgrading Firmware
Use the PrintServer’s Web-based Utility to upgrade its firmware. Follow these instructions:
1. Visit www.linksys.com and download the firmware upgrade file for the Wireless-G PrintServer.
2. Extract the file on your computer.
3. Open the PrintServer’s Web-based Utility.
4. Click the Status tab, and then click the Device tab.
5. On the Device screen, click the Upgrade button.
6. On the Firmware Upgrade screen, enter the location of the extracted firmware file, or click the Browse button
to find this file.
7. Click the Start Upgrade button, and follow the on-screen instructions.
Figure D-1: Status Tab - Device
Figure D-2: Firmware Upgrade
63
Appendix E: Windows Help
Wireless-G PrintServer
Appendix E: Windows Help
All Linksys wireless products require Microsoft Windows. Windows is the most used operating system in the
world and comes with many features that help make networking easier. These features can be accessed through
Windows Help and are described in this appendix.
TCP/IP
TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless
networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled.
Windows Help provides complete instructions on enabling TCP/IP.
Shared Resources
If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on
utilizing shared resources.
Network Neighborhood/My Network Places
Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the
version of Windows you're running). Windows Help provides complete instructions on adding PCs to your
network.
64
Appendix F: Glossary
Wireless-G PrintServer
Appendix F: Glossary
802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an
operating frequency of 2.4GHz.
802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating
frequency of 2.4GHz, and backward compatibility with 802.11b devices.
Access Point - A device that allows wireless-equipped computers and other devices to communicate with a
wired network. Also used to expand the range of a wireless network.
Adapter - A device that adds network functionality to your PC.
Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of
an access point.
AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.
Backbone - The part of a network that connects most of the systems and networks together, and handles the
most data.
Bandwidth - The transmission capacity of a given device or network.
Beacon Interval - Data transmitted on your wireless network that keeps the network synchronized.
Bit - A binary digit.
Boot - To start a device and cause it to start executing instructions.
Bridge - A device that connects different networks.
Broadband - An always-on, fast Internet connection.
Browser - An application program that provides a way to look at and interact with all the information on the
World Wide Web.
Buffer - A shared or assigned memory area that is used to support and coordinate different computing and
networking activities so one isn't held up by the other.
Byte - A unit of data that is usually eight bits long
65
Appendix F: Glossary
Wireless-G PrintServer
Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the
Internet.
CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent
data collisions.
CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive data.
Daisy Chain - A method used to connect devices in a series, one after the other.
Database - A collection of data that is organized so that its contents can easily be accessed, managed, and
updated.
DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a
fixed domain name (e.g., www.xyz.com) and a dynamic IP address.
Default Gateway - A device that forwards Internet traffic from your local area network.
DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign
temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time,
instead of assigning permanent IP addresses.
DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from
the Internet.
DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP
addresses.
Domain - A specific name for a network of computers.
Download - To receive a file transmitted over a network.
DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.
DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a
lower probability of information being lost in transit.
DTIM (Delivery Traffic Indication Message) - A message included in data packets that can increase wireless
efficiency.
Dynamic IP Address - A temporary IP address assigned by a DHCP server.
66
Appendix F: Glossary
Wireless-G PrintServer
EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.
Many specific authentication methods work within this framework.
EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A mutual
authentication method that uses a combination of digital certificates and another system, such as passwords.
EAP-TLS (Extensible Authentication Protocol-Transport Layer Security) - A mutual authentication method that
uses digital certificates.
Encryption - Encoding data transmitted in a network.
Ethernet - A networking protocol that specifies how data is placed on and retrieved from a common transmission
medium.
Finger - A program that tells you the name associated with an e-mail address.
Firewall - A set of related programs located at a network gateway server that protects the resources of a
network from users from other networks.
Firmware - The programming code that runs a networking device.
Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot
support the original size of the packet.
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.
Full Duplex - The ability of a networking device to receive and transmit data simultaneously.
Gateway - A device that interconnects networks with different, incompatible communications protocols.
Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a
time.
Hardware - The physical aspect of computers, telecommunications, and other information technology devices.
HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World
Wide Web.
Infrastructure - A wireless network that is bridged to a wired network via an access point.
IP (Internet Protocol) - A protocol used to send data over a network.
IP Address - The address used to identify a computer or device on a network.
67
Appendix F: Glossary
Wireless-G PrintServer
IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.
IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.
ISM band - Radio bandwidth utilized in wireless transmissions.
ISP (Internet Service Provider) - A company that provides access to the Internet.
LAN - The computers and networking products that make up your local network.
LEAP (Lightweight Extensible Authentication Protocol) - A mutual authentication method that uses a username
and password system.
MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking
device.
Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.
mIRC - An Internet Relay Chat program that runs under Windows.
Multicasting - Sending data to a group of destinations at once.
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different
IP address for the Internet.
Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or
transmission between users.
NNTP (Network News Transfer Protocol) - The protocol used to connect to Usenet groups on the Internet.
Node - A network junction or connection point, typically a computer or work station.
OFDM (Orthogonal Frequency Division Multiplexing) - Frequency transmission that separates the data stream
into a number of lower-speed data streams, which are then transmitted in parallel to prevent information from
being lost in transit.
Packet - A unit of data sent over a network.
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically
generating the WEP encryption keys for Linksys products.
Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.
68
Appendix F: Glossary
Wireless-G PrintServer
POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.
Port - The connection point on a computer or networking device used for plugging in cables or adapters.
Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.
PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication
(username and password) in addition to data transport.
PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be
tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.
Preamble - Part of the wireless signal that synchronizes network traffic.
RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control
network access.
RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.
Roaming - The ability to take a wireless device from one access point's range to another without losing the
connection.
Router - A networking device that connects multiple networks together.
RTS (Request To Send) - A networking method of coordinating large packets through the RTS Threshold setting.
Server - Any computer whose function in a network is to provide user access to files, printing, communications,
and other services.
SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.
SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.
Software - Instructions for the computer. A series of instructions that performs a particular task is called a
“program”.
SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in small offices.
SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before
allowing them to enter the network.
Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission.
69
Appendix F: Glossary
Wireless-G PrintServer
SSID (Service Set IDentifier) - Your wireless network's name.
Static IP Address - A fixed address assigned to a computer or device that is connected to a network.
Static Routing - Forwarding data in a network via a fixed path.
Subnet Mask - An address code that determines the size of the network.
Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of
devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an
electrical circuit.
TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement
from the recipient of data sent.
TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a
network.
Telnet - A user command and TCP/IP protocol used for accessing remote PCs.
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password
capability.
Throughput - The amount of data moved successfully from one node to another in a given time period.
TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for
each packet transmitted.
Topology - The physical layout of a network.
TX Rate - Transmission Rate.
UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement
from the recipient of the data that is sent.
Upgrade - To replace existing software or firmware with a newer version.
Upload - To transmit a file over a network.
URL (Uniform Resource Locator) - The address of a file located on the Internet.
VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another
over the Internet.
70
Appendix F: Glossary
Wireless-G PrintServer
WAN (Wide Area Network)- The Internet.
WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for
greater security.
WINIPCFG - A Windows 98 and Me utility that displays the IP address for a particular networking device.
WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with
each other wirelessly.
WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol)
encryption, which can be used in conjunction with a RADIUS server.
71
Appendix G: Specifications
Wireless-G PrintServer
Appendix G: Specifications
Model WPS54G ver. 2.0
Standards IEEE 802.11g, IEEE 802.11b, IEEE 802.3, USB 2.0
Ports Power, Ethernet, USB Printer
Button Reset
Cabling Type USB 2.0, UTP CAT5
LEDs Power, Ethernet, Wireless, USB
Security Features WEP, WPA-PSK
WEP Key Bits 64, 128
Dimensions 5.24" x 0.98" x 2.76"
(W x H x D) (133 mm x 25 mm x 70 mm)
Unit Weight 3.80 oz. (0.11 kg)
Power 5 V DC, 2A
Certifications FCC, CE
Operating Temp. 0ºC to 40ºC (32ºF to 104ºF)
Storage Temp. -20ºC to 70ºC (-4ºF to 158ºF)
Operating Humidity 10% to 85%, Non-Condensing
Storage Humidity 5% to 90%, Non-Condensing
72
Appendix H: Warranty Information
Wireless-G PrintServer
Appendix H: Warranty Information
LIMITED WARRANTY
Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially
free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under
this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any
rebates. This limited warranty extends only to the original purchaser.
If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return
Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are
requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a
copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You
are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You
only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling
charges.
ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives
You specific legal rights, and You may also have other rights which vary by jurisdiction.
This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated,
repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal
physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new
techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of
vulnerability to intrusion or attack.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT,
OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF
LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT
(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even
if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
73
Appendix I: Regulatory Information
Wireless-G PrintServer
Appendix I: Regulatory Information
FCC Statement
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment or devices
• Connect the equipment to an outlet other than the receiver's
• Consult a dealer or an experienced radio/TV technician for assistance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA.
74
Appendix I: Regulatory Information
Wireless-G PrintServer
Safety Notices
Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Industry Canada (Canada)
This device complies with Canadian ICES-003 and RSS210 rules.
Cet appareil est conforme aux normes NMB-003 et RSS210 d'Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow
the specific operating instructions for satisfying RF exposure compliance. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Règlement d'Industry Canada
Les conditions de fonctionnement sont sujettes à deux conditions:
1. Ce périphérique ne doit pas causer d'interférence et.
2. Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le bon fonctionnement
de ce périphérique.
75
Appendix I: Regulatory Information
Compact Wireless-G Broadband Router
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic
Equipment (WEEE)
This document contains important information for users with regards to the proper disposal and recycling of Linksys
products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
76
Appendix I: Regulatory Information
Compact Wireless-G Broadband Router
77
Appendix I: Regulatory Information
Compact Wireless-G Broadband Router
78
Appendix I: Regulatory Information
Compact Wireless-G Broadband Router
79
Appendix I: Regulatory Information
Wireless-G Broadband Router with RangeBooster
For more information, visit www.linksys.com.
80
Appendix J: Contact Information
Wireless-G PrintServer
Appendix J: Contact Information
Need to contact Linksys?
Visit us online for information on the latest products and updates
to your existing products at: http://www.linksys.com or
ftp.linksys.com
Can't find information about a product you want to buy
on the web? Do you want to know more about networking
with Linksys products? Give our advice line a call at: 800-546-5797 (LINKSYS)
Or fax your request in to: 949-823-3002
If you experience problems with any Linksys product,
you can call us at: 800-326-7114
Don't wish to call? You can e-mail us at: support@linksys.com
If any Linksys product proves defective during its warranty period,
you can call the Linksys Return Merchandise Authorization
department for obtaining a Return Authorization Number at: 949-823-3000
(Details on Warranty and RMA issues can be found in the Warranty
Information section in this Guide.)