LINKSYS WPSM54GV11 Wireless-G PrintServer User Manual Book
LINKSYS LLC Wireless-G PrintServer Book
LINKSYS >
Contents
- 1. Manual 1
- 2. Manual 2
Manual 1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 815166 |
| Application ID | BZ2PWoeYKAj0T4V3DPTMew== |
| Document Description | Manual 1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 98.39kB (1229931 bits) |
| Date Submitted | 2007-07-12 00:00:00 |
| Date Available | 2007-07-12 00:00:00 |
| Creation Date | 2007-07-11 16:49:48 |
| Producing Software | Acrobat Distiller 6.0.1 (Windows) |
| Document Lastmod | 2007-07-11 16:50:02 |
| Document Title | Book Template.book |
| Document Creator | FrameMaker 7.0 |
| Document Author: | junelee |
2.4 GHz Wireless-G 802.11g PrintServer with WIRELESS Model No. Multifunction Printer Support WPSM54G V1.1 User Guide Wireless-G PrintServer with Multifunction Printer Support Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. How to Use this User Guide The user guide to the Wireless-G PrintServer with Multifunction Printer Support has been designed to make understanding networking with the PrintServer easier than ever. Look for the following items when reading this User Guide: This checkmark means there is a note of interest and is something you should pay special attention to while using the PrintServer. This exclamation point means there is a caution or warning and is something that could damage your property or the PrintServer. This question mark provides you with a reminder about something you might need to do while using the PrintServer. In addition to these symbols, there are definitions for technical terms that are presented like this: word: definition. Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this: Figure 0-1: Sample Figure Description Figure numbers and descriptions can also be found in the “List of Figures” section. WPSM54G-UG-60801NC JL Wireless-G PrintServer with Multifunction Printer Support Table of Contents Chapter 1: Introduction Welcome What’s in this Guide? Chapter 2: Getting to Know the PrintServer The Bottom Panel The Front Panel Chapter 3: Connecting the PrintServer Overview Connecting the PrintServer to Your Network Placement Options Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation Chapter 5: Windows Driver Installation 20 Overview Installation Configuration of the PrintServer Driver 20 20 22 Chapter 6: Configuring the PrintServer Using the Web-based Utility Overview The Setup Tab The Protocol Tab - TCP/IP The Protocol Tab - AppleTalk The Protocol Tab - NetBEUI The Protocol Tab - SNMP The Wireless Tab - Basic The Wireless Tab - Security The Printer Tab - Internet Printing The Printer Tab - Logical Port The Status Tab - Device The Status Tab - Printer The Status Tab - Wireless The Exit Tab 25 25 26 27 28 29 30 31 32 33 34 35 36 36 36 Wireless-G PrintServer with Multifunction Printer Support Chapter 7: Bi-Admin Management 37 Overview Bi-Admin Installation Starting the Bi-Admin Management Utility The Bi-Admin Management Utility 37 37 39 40 Chapter 8: Internet Printing Protocol (IPP) 51 Overview Windows IPP Client Setup Appendix A: Troubleshooting Common Problems and Solutions Appendix B: Wireless Security Security Precautions Security Threats Facing Wireless Networks Appendix C: About Bi-Directional Printing Appendix D: Upgrading Firmware Appendix E: Windows Help Appendix F: Glossary Appendix G: Specifications Appendix H: Warranty Information Appendix I: Regulatory Information Appendix J: Contact Information 51 51 56 56 58 58 58 61 62 63 64 69 70 71 73 Wireless-G PrintServer with Multifunction Printer Support List of Figures Figure 2-1: PrintServer’s Bottom Panel Figure 2-2: PrintServer’s Front Panel Figure 3-1: Connect to the USB Port Figure 3-2: Connect to the Ethernet Port Figure 3-3: Desktop Placement Figure 4-1: Welcome Figure 4-2: Set up PrintServer Figure 4-3: Disconnect the USB Printer cable and power Figure 4-4: Connect the PrintServer to the Printer Figure 4-5: Connect the PrintServer Figure 4-6: Connect the PrintServer Figure 4-7: Reconnect the Printer Figure 4-8: Choose PrintServer Figure 4-9: Password Figure 4-10: Configure IP Settings Figure 4-11: Set PrintServer Password Figure 4-12: Select Wireless Network Figure 4-13: Configure Wireless Settings - SSID Figure 4-14: Select Wireless Network Figure 4-15: Wireless Security Settings - Disabled Figure 4-16: Wireless Security - WEP Figure 4-17: Wireless Security - WPA-Pre-Shared Figure 4-18: Confirm New Settings Figure 4-19: Disconnect power to the PrintServer Figure 4-20: Disconnect Network Figure 4-21: Reconnect the PrintServer Figure 4-22: PrintServer connection complete Figure 4-23: Continue to Set up Computer Figure 5-1: Welcome Figure 5-2: Set up Computer Figure 5-3: Select Printer 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 21 21 22 Wireless-G PrintServer with Multifunction Printer Support Figure 5-4: Check Print Driver Figure 5-5: Wireless-G PrintServer Diagnostic - Check Printer Driver Installation Figure 5-6: Printer Driver Not Installed Figure 5-7: Print Test Page Figure 5-8: PrintServer Diagnostic Icon Figure 5-9: PrintServer Info Figure 5-10: Right-click Icon Figure 6-1: Setup Tab Figure 6-2: Protocol Tab - TCP/IP Figure 6-3: Protocol Tab - AppleTalk Figure 6-4: Protocol Tab - NetBEUI Figure 6-5: Protocol Tab - SNMP Figure 6-6: Wireless Tab - Basic Figure 6-7: Wireless Tab - Security (WEP) Figure 6-8: Wireless Tab - Security (WPA) Figure 6-9: Printer - Internet Printing Figure 6-10: Printer - Logical Port Figure 6-11: Status Tab - Device Figure 6-12: Firmware Upgrade Figure 6-13: Status Tab - Printer Figure 6-14: Status Tab - Wireless Figure 6-15: Exit Figure 7-1: Welcome Figure 7-2: Bi-Admin Setup Welcome Figure 7-3: Choose Destination Location Figure 7-4: Select Program Folder Figure 7-5: Connected Protocol Figure 7-6: Searching for Device Figure 7-7: Bi-Admin Management Utility Figure 7-8: Device Information Figure 7-9: Printer Status Figure 7-10: Configuration - System Figure 7-11: Configuration - TCP/IP 22 23 23 23 24 24 24 26 27 28 29 30 31 32 32 33 34 35 35 36 36 36 37 37 38 38 39 39 40 40 41 42 43 Wireless-G PrintServer with Multifunction Printer Support Figure 7-12: Configuration - AppleTalk Figure 7-13: Configuration - NetBEUI Figure 7-14: Configuration - Internet Printing Figure 7-15: Configuration - Port Figure 7-16: Configuration - Wireless Figure 7-17: Configuration - SNMP Figure 7-18: Upgrade Figure 7-19: Detected LAN Cards Figure 7-20: BIN File Information Figure 7-21: Add Cross Segment PrintServer Figure 8-1: Windows XP - Local or Network Printer Figure 8-2: Windows XP - Specify a Printer Figure 8-3: Windows 2000 - Locate Your Printer Figure D-1: Status Tab - Device Figure D-2: Firmware Upgrade 44 45 46 47 48 49 50 50 50 50 53 54 54 62 62 Wireless-G PrintServer with Multifunction Printer Support Chapter 1: Introduction Welcome Thank you for choosing the Linksys Wireless-G PrintServer with Multifunction Printer Support. The PrintServer lets you connect a USB printer directly to your network, eliminating the need to dedicate a PC to print sharing chores. Using a PrintServer frees up your “print share PC” so you don’t have to leave it on all the time. It also removes the printing bottleneck, and sets your PC free to do more useful work. The USB port is compatible with USB 1.1 printers, as well as printers that support the new high-speed USB 2.0 specification for even faster throughput. How does the PrintServer do all of this? A print server is a device that allows multiple computers to share a printer over a network. You can connect the PrintServer directly to your network using an Ethernet network cable, or you can connect the PrintServer over Wireless-G (802.11g) at up to 54Mbps. The wireless option lets you put your printer wherever you want to, without having to run a cable. Whichever way the PrintServer is attached to your network, both your wireless and wired PCs will have access to it and its USB printer. But what does all of this mean? Networks are useful tools for sharing Internet access and computer resources. Multiple computers can share Internet access, so you don’t need more than one high-speed Internet connection. Using the PrintServer, you can access one printer from different computers. Plus, you can access data located on another computer’s hard drive and play multi-player video games. So, networks not only are useful in homes and offices, but also can be fun. PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is why the network is called “wired”. PCs equipped with wireless cards or adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network. This is sometimes called a WLAN, or Wireless Local Area Network. Your network router bridges wireless networks of both 802.11b and 802.11g standards and wired networks, allowing them to communicate with each other. To guide you through the process of installing the PrintServer, run the Setup Wizard on the Setup CD-ROM (you can use the instructions in the Quick Installation or User Guide to help you). After you have installed the PrintServer, you can change its settings using its browser-based utility, which is described in this User Guide. These instructions should be all you need to get the most out of the Wireless-G PrintServer. Chapter 1: Introduction Welcome mbps: one million bits per second; a unit of measurement for data transmission lan (local area network): the computers and networking products that make up the network in your home or office ethernet: an IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium 802.11b: an IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz 802.11g: an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices browser: an application program that provides a way to look at and interact with all the information on the World Wide Web Wireless-G PrintServer with Multifunction Printer Support What’s in this Guide? This user guide covers the steps for setting up and using the PrintServer. • Chapter 1: Introduction This chapter describes the PrintServer’s applications and this User Guide. • Chapter 2: Getting to Know the PrintServer This chapter describes the physical features of the PrintServer. • Chapter 3: Connecting the PrintServer This chapter instructs you on how to connect the PrintServer to your network. • Chapter 4: Configuring the PrintServer using the Setup Wizard This chapter instructs you on how to use the Setup Wizard to install your PrintServer. • Chapter 5: Windows Driver Installation This chapter explains how to install the Windows driver for the PrintServer. • Chapter 6: Configuring the PrintServer Using the Web-based Utility This chapter explains use the web-based utility to change the PrintServer’s settings. • Chapter 7: Bi-Admin Management This chapter explains how to use the Bi-Admin Management utility, which is for advanced users only. • Chapter 8: Internet Printing Protocol (IPP) This chapter instruct you on how to use the PrintServer as an IPP server so you can run remote print jobs. • Appendix A: Troubleshooting This appendix describes some potential problems and solutions regarding use of the PrintServer. • Appendix B: Wireless Security This appendix explains the security risks in wireless networking and how you can help protect your network • Appendix C: About Bi-Directional Printing This appendix describes bi-directional printing. • Appendix D: Upgrading Firmware This appendix instructs you on how to upgrade the firmware on the PrintServer should you need to do so. Chapter 1: Introduction What’s in this Guide? Wireless-G PrintServer with Multifunction Printer Support • Appendix E: Windows Help This appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol. • Appendix F: Glossary This appendix gives a brief glossary of terms frequently used in networking. • Appendix G: Specifications This appendix provides the technical specifications for the PrintServer. • Appendix H: Warranty Information This appendix supplies the warranty information for the PrintServer. • Appendix I: Regulatory Information This appendix supplies the regulatory information regarding the PrintServer. • Appendix J: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support. Chapter 1: Introduction What’s in this Guide? Wireless-G PrintServer with Multifunction Printer Support Chapter 2: Getting to Know the PrintServer The Bottom Panel The PrintServer’s ports and Reset button are located on the bottom panel. Figure 2-1: PrintServer’s Bottom Panel Power The Power port is where you will connect the power adapter. Ethernet The Ethernet port is where you will connect the PrintServer to your wired network. (This is optional.) USB Printer The USB Printer port is where you will connect the USB printer to the PrintServer. The USB icon (right) designates a USB port. The PrintServer comes with a USB cable. One end has a rectangular connector called Type A. The other end has a square connector called Type B. The USB cable’s Type A end connects to the PrintServer, and the Type B end connects to the printer. USB Connector-Type A Reset Button USB Connector-Type B Use the Reset Button to reset the PrintServer to its factory defaults or print a test page. The instructions are provided on the right side of this page. Chapter 2: Getting to Know the PrintServer The Bottom Panel IMPORTANT: Resetting the PrintServer will delete all of your settings and replace them with the factory defaults. Do not reset the PrintServer if you want to retain the settings. To reset the factory default settings 1. Unplug the PrintServer. 2. Press and hold the Reset button. While pressing the button, plug in the PrintServer. 3. If you continue pressing the button for 10 seconds, the PrintServer will be reset to factory defaults. To generate a diagnostic print-out 1. Ensure that both the PrintServer and the printer attached to the Printer port are ON. 2. Press the Reset button, and hold it in for 2 seconds. 3. The test page, which lists the current settings, will be printed. PostScript printers are unable to print this page. If you have a PostScript printer on the USB Printer port, the test page will not be printed. Wireless-G PrintServer with Multifunction Printer Support The Front Panel The PrintServer’s LEDs are located on the front panel. Figure 2-2: PrintServer’s Front Panel USB Green/Orange. The USB LED lights up green when there is a printer connected to the USB port. The LED flashes green when the PrintServer is sending data through the USB port. It lights up orange when there is a problem with the USB printer. Wireless Green. The Wireless LED serves two purposes. If the LED is continuously lit, the PrintServer is successfully connected to the wireless network. If the LED is flashing, the PrintServer is actively sending or receiving data from the wireless network. Ethernet Green/Orange. If the Ethernet LED is continuously lit green, the PrintServer is successfully connected to a device through the Ethernet port. The LED flashes green when the PrintServer is actively sending or receiving data from the wired network. It flashes orange when there are collisions detected on the Ethernet port. Power Green/Orange. If the Power LED is continuously lit green, then the PrintServer is ready for use. The LED flashes green when the PrintServer is booting up, a system self-test is running, or the firmware is being upgraded. It lights up orange when there is an error. Chapter 2: Getting to Know the PrintServer The Front Panel Wireless-G PrintServer with Multifunction Printer Support Chapter 3: Connecting the PrintServer Overview Before starting the physical installation, note the PrintServer’s default name, which starts with “LK” (for example, LK71107). The default name is shown in the Server field on the PrintServer’s sticker, which is located on the PrintServer’s back panel. During the PrintServer driver installation, this name is used to identify the PrintServer you are currently installing. Connecting the PrintServer to Your Network 1. Use the USB cable to connect your USB printer to the PrintServer’s USB Printer port. Plug the Type A connector end into the PrintServer and the Type B connector end into the printer. 2. If you are connecting the PrintServer to your wired network, then plug one end of the Ethernet network cable into the PrintServer’s Ethernet port. Then connect the other end of the cable to your router or switch. The distance between the PrintServer and the other device should not exceed 328 feet (100 meters). Figure 3-1: Connect to the USB Port 3. Power on your printer. 4. Plug the power adapter into the PrintServer’s Power port. Then plug the other end into an electrical outlet. IMPORTANT: Make sure you use the power adapter supplied with the PrintServer. Use of a different power adapter could damage the PrintServer. NOTE: The PrintServer does not have an on/off power switch. Whenever its power adapter is plugged into a power supply, the PrintServer is powered on. The PrintServer can be powered on before, during, or after your network is powered on. Figure 3-2: Connect to the Ethernet Port Proceed to the next section, “Placement Options.” Chapter 3: Connecting the PrintServer Overview Wireless-G PrintServer with Multifunction Printer Support Placement Options There are different ways to place the PrintServer. The first way is to place the PrintServer horizontally on a surface, so it sits on four small rubber pads. You can also use the included velcro to mount the PrintServer on a wall or underneath a shelf. To use the velcro, follow these instructions: 1. Separate the included velcro into its two sides, the hook side and the loop side. You will use the tape on the backs of the velcro sides to attach them to the PrintServer and surface you want to use. 2. For the first velcro side, peel off the cover protecting the tape, and attach it to the recessed area on the back panel of the PrintServer. 3. For the other velcro side, peel off the cover, and attach it to the location you have chosen for the PrintServer. 4. Attach the velcro sides to each other, and make sure the PrintServer is securely mounted on the wall or underneath the shelf. 5. Adjust the position of the antenna so that it is positioned as high as possible. Usually, the higher you place the antenna, the better the performance and range will be. The physical installation of the Wireless-G PrintServer with Multifunction Printer Support is complete. Proceed to “Chapter 4: Configuring the PrintServer Using the Setup Wizard.” Figure 3-3: Desktop Placement Chapter 3: Connecting the PrintServer Placement Options Wireless-G PrintServer with Multifunction Printer Support Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation To install the PrintServer, you will use the Setup CD-ROM to run the Setup Wizard. It is highly recommended that you use a computer on the wired network to set up the PrintServer. However, if you only have a wireless network, then you can use a computer on the wireless network to set up the PrintServer. 1. Insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup Wizard should run automatically. If it does not, click the Start button and choose Run. In the box that appears, enter D:\setupWizard.exe (if “D” is the letter of your CD-ROM drive). 2. When you see the Welcome screen, click Setup Wizard to continue. Click Exit to end the installation. Click User Guide button to view the User Guide. Figure 4-1: Welcome 3. If this is the first time you have installed the PrintServer, click Set up PrintServer. If you have already installed and configured the PrintServer, click Set up Computer and proceed to Chapter 5: Windows Driver Installation. Figure 4-2: Set up PrintServer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation Wireless-G PrintServer with Multifunction Printer Support 4. You will need to first disconnect the USB Printer cable from the computer and disconnect the power from the printer. Click Next when finished. Figure 4-3: Disconnect the USB Printer cable and power 5. In Step 2, you will connect the USB printer cable to the USB port on the Print Server. Click Next. Figure 4-4: Connect the PrintServer to the Printer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation Wireless-G PrintServer with Multifunction Printer Support 6. From the Connecting Your PrintServer screen, you will connect your Ethernet port. The Ethernet connection is for configuration purposes only. Later in this installation, you will need to disconnect the ethernet cable and reconnect your PrintServer, printer, and router. Click Next to continue. Click Back to return to the previous screen. Figure 4-5: Connect the PrintServer 7. Connect the Power Adapter to the PrintServer and click Next. Figure 4-6: Connect the PrintServer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 10 Wireless-G PrintServer with Multifunction Printer Support 8. Reconnect the power adapter to the printer. Plug the power into the wall outlet. Click Next to continue, or click Back to return to the previous screen. Wait a few moments while the system searches for the PrintServer. Figure 4-7: Reconnect the Printer 9. Select the proper PrintServer. If you can not find the PrintServer, click Refresh. Click Next. Figure 4-8: Choose PrintServer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 11 Wireless-G PrintServer with Multifunction Printer Support 10. If you have changed the default password previously, the password dialog opens and you are prompted for your password. Otherwise, the installation will continue. If you have forgotten your password, hold the reset button on the side of the PrintServer for 10 seconds. This will reset the device to factory default. The default password is admin. Figure 4-9: Password 11. The Configure IP Settings screen appears. If your network uses a router with a DHCP setting that automatically assigns IP addresses, select Automatically obtain an IP address (DHCP). If your network uses a static IP address, select Set IP configuration manually, and enter the IP Address, Subnet Mask, and Gateway in the fields provided. Click Next to continue, or click Back to return to the previous screen. Figure 4-10: Configure IP Settings ip (internet protocol): a protocol used to send data over a network ip address: the address used to identify a computer or device on a network static ip address: a fixed address assigned to a computer or device connected to a network. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 12 Wireless-G PrintServer with Multifunction Printer Support 12. The Set PrintServer’s Password screen appears. If you want to change your password, enter your current password in the Password field. Enter the new password in the Confirm field. Click Next to continue, or click Back to return to the previous screen. Figure 4-11: Set PrintServer Password 13. Locate and select the wireless network you want to connect to. If you do not see the wireless network you wish to use, click Refresh and locate the network. Click Next to continue, or click Back to return to the previous screen. Figure 4-12: Select Wireless Network Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 13 Wireless-G PrintServer with Multifunction Printer Support 14. If you clicked Manual Setup, the Configure Wireless Settings screen appears with the SSID field. Enter your wireless network’s SSID or name. This is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32 characters or fewer. Click Next to continue, or click Back to return to the previous screen. Figure 4-13: Configure Wireless Settings - SSID If you click Refresh and select the network, the setup wizard automatically detects what kind of security network your computer has. Figure 4-14: Select Wireless Network Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 14 Wireless-G PrintServer with Multifunction Printer Support 15. If your network uses wireless security, you will prompted to enter the correct information. Figure 4-15: Wireless Security Settings - Disabled If you enter a Passphrase, you will see the automatically generated WEP key on the following screen. Otherwise, enter the WEP key manually in the field provided. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are “0”-“9” and “A”-“F”. Click Next to continue, or click Back to return to the previous screen. Figure 4-16: Wireless Security - WEP Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 15 Wireless-G PrintServer with Multifunction Printer Support WPA-Pre-Shared Key Enter a Pre-Shared Key that is 8-63 characters in length. Click Next to continue, or click Back to return to the previous screen. Figure 4-17: Wireless Security - WPA-Pre-Shared 16. The Confirmation screen will appear. Your old and new settings will be displayed. If you want to save the new settings, click Next. If you want to make a change, click Back to make changes. Please wait a few moments while the system changes the PrintServer’s settings. NOTE: In the next few screens, you will need to disconnect and reconnect your PrintServer. Proceed in the order specified to avoid any networking conflicts. Figure 4-18: Confirm New Settings Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 16 Wireless-G PrintServer with Multifunction Printer Support 17. Disconnect the power to the PrintServer. Click Next. Figure 4-19: Disconnect power to the PrintServer 18. Disconnect the Network Cable from the PrintServer and router. Figure 4-20: Disconnect Network Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 17 Wireless-G PrintServer with Multifunction Printer Support 19. Reconnect the power to the PrintServer and click Next. Wait a few moments while the system checks for the network. Figure 4-21: Reconnect the PrintServer 20. The PrintServer is now connected to your wireless network properly. The order used in reconnecting your PrintServer, router, and printer is very important. If you may have reconnected improperly, please click Back and review your processes. Figure 4-22: PrintServer connection complete Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 18 Wireless-G PrintServer with Multifunction Printer Support 21. Now you have finished the initial setup.. You will need to install the driver next. Click Set up Computer at the bottom of this, and go to “Chapter 5: Windows Driver Installation” of this user guide. Figure 4-23: Continue to Set up Computer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 19 Wireless-G PrintServer with Multifunction Printer Support Chapter 5: Windows Driver Installation Overview This section installs the PrintServer’s software on your Windows 98, Me, 2000, or XP computers so they can use the PrintServer for print jobs. (The PrintServer is fully compatible with Windows 98, Me, 2000, and XP.) At this point, you must have the following: • the PrintServer hardware installed on your network. If not, see “Chapter 3: Connecting the PrintServer.” • TCP/IP installed on each of your computers. • an IP address assigned to each of the computers on your network. • an IP address assigned to the PrintServer by you or your network router. By default the PrintServer has DHCP enabled so the network router will automatically assign an IP address. If you need to manually assign an IP address, run the Setup Wizard on the Setup CD-ROM or go to “Chapter 7: Bi-Admin Management.” It is assumed that your CD-ROM drive’s letter name is designated as “D”. If your CD-ROM drive is named another letter, replace all instances of “D” with the appropriate letter. HAVE YOU: already set up your printer? Linksys recommends that you set up your printer and install your printer’s driver before you install the PrintServer’s driver. If you need to install the PrintServer’s driver on computers without a CD-ROM drive, you can create a setup disk by using a computer with a CD-ROM drive to copy the contents of D:\Driver\PTP onto a floppy disk. Installation 1. Make sure you have no programs or applications running on your computer. 2. If you haven’t already done so, insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup CDROM should run automatically. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setupWizard.exe (if “D” is the letter of your CD-ROM drive). Chapter 5: Windows Driver Installation Overview 20 Wireless-G PrintServer with Multifunction Printer Support 3. When you see the Welcome screen, click Click Here to Start to continue. Click Exit to end the installation. Figure 5-1: Welcome 4. Click Set up Computer. Figure 5-2: Set up Computer Configuration of the PrintServer Driver Chapter 5: Windows Driver Installation Installation 21 Wireless-G PrintServer with Multifunction Printer Support Configuration of the PrintServer Driver 1. The Wireless-G PrintServer Driver screen automatically appears. Select the PrintServer you are installing. Then click Next. NOTE: If the PrintServer is not listed, then click Refresh. If the PrintServer cannot be found, then select to temporarily disable the firewall and click Refresh again. Figure 5-3: Select Printer 2. The Checking Printer Driver screen appears. Select the driver for your printer, and click Next to continue. If the driver for your printer is not installed, you will see a new window pop up. The message will ask you to exit the Wizard and install the driver for your printer. Click OK and install the driver. After the driver has been installed, run the Setup Wizard and click Driver Install on the Welcome screen. Figure 5-4: Check Print Driver Chapter 5: Windows Driver Installation Configuration of the PrintServer Driver 22 Wireless-G PrintServer with Multifunction Printer Support 3. The Wireless-G PrintServer Driver screen appears. Review the PrintServer status and then click Next. Figure 5-5: Wireless-G PrintServer Diagnostic - Check Printer Driver Installation 4. The Wireless-G PrintServer Driver screen appears. If you want to print a test page, click Test Print. Then click Finish. Figure 5-6: Printer Driver Not Installed 5. If you’ve chosen to print a test page, the test page dialog appears. Click OK. Figure 5-7: Print Test Page Chapter 5: Windows Driver Installation Configuration of the PrintServer Driver 23 Wireless-G PrintServer with Multifunction Printer Support 6. The Print Server diagnostic icon will appear in the system tray of your desktop. When you double-click the icon, you will see the PrintServer Info screen. If you want to run the wizard that configures the printer driver, click the Diagnostics button. Figure 5-8: PrintServer Diagnostic Icon To close the PrintServer Info screen, click the Close button. When you right-click the Print Server diagnostic icon, you will see a menu. To see the version number of the Print Server Utility, click About. To see the PrintServer Info screen, click Info. To close the Utility, click Exit. The driver installation and configuration is complete. You can now use the PrintServer. If you would like to change the PrintServer’s settings, use the PrintServer’s web-based utility. For more information, refer to “Chapter 6: Configuring the PrintServer Using the Web-based Utility.” Figure 5-9: PrintServer Info Figure 5-10: Right-click Icon Chapter 5: Windows Driver Installation Configuration of the PrintServer Driver 24 Wireless-G PrintServer with Multifunction Printer Support Chapter 6: Configuring the PrintServer Using the Web-based Utility Overview After setting up the PrintServer with the Setup Wizard, the PrintServer will be ready for use. However, if you’d like to change its settings, use the PrintServer’s web-based utility. This chapter will describe each web page of the utility and each page’s key functions. The utility can be accessed via your web browser through the use of a networked computer. There are six main tabs: Setup, Protocol, Wireless, Printer, Status, and Exit. Additional tabs will be available after you click one of the main tabs, except for the Setup tab. To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the PrintServer’s IP address in the Address field. Then press Enter. NOTE: Use the PrintServer’s IP address that you noted when you ran the Setup Wizard. Otherwise, insert the Setup CD-ROM, and when the Welcome screen appears, click Setup Wizard. Follow the instructions until you reach the Wireless-G PrintServer Setup screen. Note the IP address, and then click Back until you reach the Welcome screen. Click Exit. Chapter 6: Configuring the PrintServer Using the Web-based Utility Overview 25 Wireless-G PrintServer with Multifunction Printer Support The Setup Tab The first screen that appears is the Setup tab and allows you to change the PrintServer’s general settings. WPS54G Device Name Enter the PrintServer’s name in the field provided. The name is located on a sticker on the bottom of the PrintServer. Password Current Password. To change the PrintServer’s password, enter the current password in the Current Password field. Figure 6-1: Setup Tab New Password and Verify Password. Enter the new password in the New Password field, and then enter the new password again in the Verify Password field. Protocols The TCP/IP protocol is enabled by default. Enable: Apple Talk or NetBEUI. Check the box(es) for AppleTalk or NetBEUI, if they are used by your network. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Setup Tab 26 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - TCP/IP Click the TCP/IP tab to view or change the TCP/IP values of the PrintServer. IP Address Obtain an IP Address Automatically. If your network router is using DHCP to assign IP addresses, select Obtain an IP Address Automatically. By default, Obtain an IP Address Automatically is enabled. Use the Following IP Address. If you need to assign the PrintServer a fixed IP address (also known as static IP address), select Use the Following IP Address, and enter the appropriate values under IP Address, Subnet Mask, and Gateway. Make sure the IP Address and Subnet Mask are appropriate for your network. If you change the PrintServer’s IP address, make sure you that you reconnect to the PrintServer using that new IP address. Otherwise, you will not be communicating with the PrintServer. In most cases, the Gateway IP address is the IP address of your router, and you should complete the Gateway field if you will use the PrintServer for Internet printing. (To find out your router’s IP address, consult your router’s documentation.) Figure 6-2: Protocol Tab - TCP/IP Connection Delay before reconnection attempt. Set how long you want the PrintServer to wait between attempts. Number of reconnection attempts. Specify the number of times that the PrintServer will attempt to connect to the network. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - TCP/IP 27 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - AppleTalk AppleTalk is a network communications protocol that allows computers to talk to each other using Ethernet. Typically only Macintoshes use AppleTalk, although other platforms can use it if they have the necessary, thirdparty software. Communication Printer Object Type. The Printer Object Type can be obtained from the manufacturer of the printer. Enter the type of printer in the field provided. For each printer connected to the PrintServer, you will choose the Communications Protocol that allows the devices on the network to communicate. Figure 6-3: Protocol Tab - AppleTalk Communication Protocol. Select the type of Communication Protocol you will use, ASCII or Binary for each printer, according to the recommendation of the printer’s manufacturer. For more information, refer to the printer’s documentation. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - AppleTalk 28 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - NetBEUI NetBEUI connection settings of the PrintServer are available on this tab. Domain Name Enter the name of the domain that you want the PrintServer associated with in the Domain Name field. If you are unsure of the Domain Name, you can find it out by looking on any computer already on the network. In Windows 98, right-click Network Neighborhood and select Properties. Under the Identification tab, there will be listed that computer’s name, and the Domain to which it is connected. For Windows Me, 2000, or XP, right-click My Network Places. In Windows Me, choose Properties from the menu that appears. In Windows 2000 or XP, choose Properties from the menu that appears. Then, right-click Local Area Connection and choose Properties. The Domain name will appear. If you want the PrintServer to be connected to that same Domain, enter that Domain name here. If no Domain name exists there, you will use the Workgroup name from that window. Figure 6-4: Protocol Tab - NetBEUI Options Response Time. You can specify the Response Time that you prefer for the PrintServer. This is the amount of time (measured in seconds) that the PrintServer will wait for a response from the network before “timing out.” Abort Print Job if Error. You also have the option to use this feature, Abort Print Job if Error. Selecting Yes here will terminate the printing if there is an error of any kind. If you select No, print jobs that have errors will be sent to the printer, but might not print properly. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - NetBEUI 29 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - SNMP Use this screen to view or change the PrintServer’s SNMP (Simple Network Management Protocol) settings. The PrintServer supports SNMP, which allows network administrators to monitor and control the PrintServer through the use of network management platforms, such as HP OpenView. The appropriate MIB file must be imported into your SNMP management program using the Import-Compile command. Check your program’s documentation for details on this procedure. The MIB file is named Mib2p.mib and is provided in the MiB folder on the Setup CD-ROM. General SysContact. Enter the name of the contact person in the SysContact field. SysLocation. Enter the location of the contact person in the SysLocation field. Figure 6-5: Protocol Tab - SNMP Management Stations Station No. Select the number of the management station from the Station No. drop-down menu (1-4). Click the Get Data button to display the information for the selected station. IP Address. Enter the IP address of the management station running the SNMP program. Community. Enter the name of the SNMP community, which is usually public or private. Access. Select the level of access for this management station, Not Accessible, Read-only, or Read/Write. Trap Receivers Receiver No. Select the number of the trap receiver from the Receiver No. drop-down menu (1-4). Click the Get Data button to display the information for the selected trap receiver. IP Address. Enter the IP address of the trap receiver that will be sent the trap messages or notifications. Community. In the Community field, enter the name of the SNMP community, which is usually public or private. Enable with Severity level. To designate a severity level, click the checkbox next to Enable with Severity level. From the following drop-down menu, select the desired level of severity, with 1 meaning least severe. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - SNMP 30 Wireless-G PrintServer with Multifunction Printer Support The Wireless Tab - Basic This screen allows you to change the PrintServer’s basic wireless settings. Configuration Regulatory Domain and MAC Address. The PrintServer’s Regulatory Domain and MAC Address are listed and cannot be changed. SSID. In the SSID field, enter the name of your wireless network. This is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32 characters or fewer. Figure 6-6: Wireless Tab - Basic Channel No. If your network is set to ad-hoc mode, select your network’s channel setting from the Channel No. drop-down menu. Network Type. The Network Type setting shows a choice of two wireless modes. Select Infrastructure if you want the PrintServer to communicate using an access point or wireless router. Select Ad-Hoc if you want the PrintServer to communicate without using an access point or wireless router. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Wireless Tab - Basic 31 Wireless-G PrintServer with Multifunction Printer Support The Wireless Tab - Security Configure the security of your wireless network on this screen. Wi-Fi Protected Access (WPA) and two levels of Wired Equivalent Privacy (WEP) encryption are available. If you do not want to use wireless security, select None from the Security Mode drop-down menu. Wireless Security Security Mode. To use WPA, select Pre-Shared Key. To use WEP, select the level of WEP encryption you want to use, 64 Bit Keys (10 Hex chars) or 128 Bit Keys (26 Hex chars). Then proceed to the instructions for your security method. WEP Figure 6-7: Wireless Tab - Security (WEP) Default Transmit Key. Select the Default Transmit Key used by your wireless network. This indicates which WEP key your network uses for WEP encryption. Passphrase. Enter a Passphrase and click the Generate Keys button to automatically generate WEP Keys 1-4. The Passphrase is case-sensitive and should have no more than 16 alphanumeric characters. It must match your wireless network’s passphrase and is compatible with Linksys wireless products only. (Enter the WEP key(s) manually on any non-Linksys wireless products.) Key 1 to Key 4. To enter the WEP keys manually, leave the Passphrase field blank and enter your WEP key(s). For 64-bit WEP encryption, each key must have 10 hexadecimal characters, while for 128-bit WEP encryption, the key must have 26 hexadecimal characters. Valid hexadecimal characters are “0”-“9” and “A”-“F”. Authentication. Select your wireless network’s authentication type. The default is Open System, for which the sender and the recipient do NOT use a WEP key for authentication. You can also choose Shared Key, for which the sender and recipient use a WEP key for authentication. Figure 6-8: Wireless Tab - Security (WPA) Click the Save button to apply your changes, or click Cancel to cancel your changes. Pre-Shared Key (WPA) WPA Algorithm. TKIP is the default algorithm. WPA Shared Key. Enter your Pre-Shared Key, which must have 8-63 characters in length. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Wireless Tab - Security 32 Wireless-G PrintServer with Multifunction Printer Support The Printer Tab - Internet Printing Internet Printing allows you to automatically print any e-mails that are sent to a specific e-mail account on your network. This is especially useful for printing information when you are not connected to the network. You can print from any location where you can access e-mail. Mail Server Mail Server IP Address. Enter the address of your mail server. (This value must be a fixed IP address.) Account Name and Password. Enter the Account Name and Account Password. Verify Password. Enter the password again in the Verify Password field. Check Mail every. Specify how often you want the PrintServer to check for e-mail to be printed. Redirect unprintable Mail to. Specify an e-mail address to which e-mails that cannot be printed are routed; this is useful for both graphic-intensive e-mails and for troubleshooting purposes. Figure 6-9: Printer - Internet Printing Printer Printer Model. Enter the Printer Model in the field provided. You can find this in the Device Manager. Printer Port. Choose the appropriate Printer Port from the drop-down menu: USB, the PrintServer’s USB port, or Logical Printer 1-3. The PrintServer has three logical or virtual printer ports. For example, you can have three different configurations for your USB printer: Logical Printer 1 for landscape orientation, Logical Printer 2 for double-sided copies, and Logical Printer 3 for manual feed. Then configure the Logical Printers on the Logical Port tab, so Logical Printers 1, 2, and 3 will be mapped to the physical printer on the PrintServer’s USB port. Options Print every E-Mail. Click this checkbox if you want to print every e-mail message. Print Banner Page. Enabled by default, this feature tells the PrintServer to print a banner page for every print job (the banner page describes the print job). Click the checkbox to remove the checkmark and disable this feature. Mail response when printed. Click this checkbox if you want an e-mail sent when a print job is complete. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Printer Tab - Internet Printing 33
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2007:07:11 16:50:02+08:00 Create Date : 2007:07:11 16:49:48+08:00 Title : Book Template.book Author : junelee Creator : FrameMaker 7.0 Producer : Acrobat Distiller 6.0.1 (Windows) Page Count : 40 Mod Date : 2007:07:11 16:50:02+08:00 Creation Date : 2007:07:11 16:49:48+08:00 Metadata Date : 2007:07:11 16:50:02+08:00 Has XFA : NoEXIF Metadata provided by EXIF.tools