LINKSYS WRT54G2V15 Wireless-G Broadband Router User Manual 6001 11414543R ai

LINKSYS LLC Wireless-G Broadband Router 6001 11414543R ai

Manual

I. Specifications Model WRT54G2 Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11g, IEEE 802.11b Ports Internet: One 10/100 RJ-45 Port LAN: Four 10/100 RJ-45 Switched Ports One Power Port Button One Reset Button One Wi-Fi Protected Setup (WPS) Button LEDs Power, Wireless, LAN (1-4), Internet, Wi-Fi Protected Setup (WPS) Cabling Type CAT5 Number of Antennas One (1) Internal Antennas RF Power Output 18 dBm UPnP able/cert Able Security Features Stateful Packet Inspection (SPI) Firewall, Internet Policy Wireless Security Wi-Fi Protected Access™2 (WPA2), WEP, Wireless MAC Filtering Environmental Dimensions 7.99" x 1.38" x 6.30" (203 x 35 x 160 mm) Weight 9.88 oz (280 g) Power External, 12V DC, 0.5A Certifications FCC, UL, CE, Wi-Fi (802.11b, 802.11g), WPA2, WMM Operating Temp. 32 to 104oF (0 to 40oC) Storage Temp. -4 to 140oF (-20 to 60oC) Operating Humidity 10 to 85%, Noncondensing Storage Humidity 5 to 90%, Noncondensing Appendix D: Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ·· Reorient or relocate the receiving antenna ·· Increase the separation between the equipment or devices ·· Connect the equipment to an outlet other than the receiver’s ·· Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.Industry Canada Statement This Class B digital apparatus complies with Canadian ICES-003 and RSS210. Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. Industry Canada Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Navigation menu