LINKSYS WRT54G3GV2 Wireless-G Router for Mobile Broadband User Manual Linksys WRT54G3GV2 ST User Guide

Download:
Mirror Download [FCC.gov]
Document ID	855798
Application ID	KkQSoqUXi8L3rX5z28cIlw==
Document Description	Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	188.67kB (2358383 bits)
Date Submitted	2007-10-17 00:00:00
Date Available	2007-10-17 00:00:00
Creation Date	2007-10-17 08:36:07
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2007-10-17 08:37:13
Document Title	Linksys WRT54G3GV2-ST User Guide
Document Creator	Adobe InDesign CS2 (4.0.5)
Document Author:	Linksys

USER GUIDE
Wireless-G
Router for
Mobile Broadband
Model No: WRT54G3GV2-ST
About This Guide
About This Guide
Icon Descriptions
While reading through the User Guide you may see
various icons that call attention to specific items. Below is
a description of these icons:
NOTE: This check mark indicates that there is
a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates
that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy
website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add http:// in front of the web address.
Resource
Website
Sprint
www.sprint.com
Linksys
www.linksys.com
Linksys International
www.linksys.com/international
Glossary
www.linksys.com/glossary
Network Security
www.linksys.com/security
Copyright and Trademarks
Specifications are subject to change without notice.
Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain
other countries. Copyright © 2007 Cisco Systems, Inc. All
rights reserved. Other brands and product names are
trademarks or registered trademarks of their respective
holders.
Wireless-G Router for Mobile Broadband
Table of Contents
Chapter 1: Product Overview
Top Panel .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Side Panel .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Opposite Side Panel with Antenna .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Front Panel .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Bottom Panel .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Placement Positions  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Chapter 2: Wireless Security Checklist
General Network Security Guidelines  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
Additional Security Tips  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
Chapter 3: Advanced Configuration
Setup > Basic Setup .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8
Setup > Mobile Network .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 12
Setup > DDNS .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 12
Setup > MAC Address Clone .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
Setup > Advanced Routing .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 14
Wireless > Basic Wireless Settings .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 14
Wireless > Wireless Security .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 15
Wireless > Wireless MAC Filter .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 17
Wireless > Advanced Wireless Settings .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 18
Security > Firewall .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 19
Security > VPN .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 19
Access Restrictions > Internet Access .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 23
Applications and Gaming > Single Port Forwarding .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 24
Applications and Gaming > Port Range Forwarding  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 24
Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .25
Applications and Gaming > DMZ  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 25
Applications and Gaming > QoS .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 26
Administration > Management .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 28
Administration > Log .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 29
Administration > Diagnostics .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 29
Administration > Factory Defaults  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 30
Administration > Firmware Upgrade .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 30
Status > Mobile Network  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 31
Status > Router .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 31
Status > Local Network .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 32
Status > Wireless Network .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 32
Appendix A: Troubleshooting
33
Appendix B: Specifications
35
Appendix C: Warranty Information
36
Wireless-G Router for Mobile Broadband
ii
Table of Contents
Appendix D: Regulatory Information
37
FCC Statement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 37
FCC Radiation Exposure Statement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 37
Safety Notices .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 37
Industry Canada Statement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 37
Avis d’Industrie Canada .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 38
Wireless Disclaimer  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 38
Avis de non-responsabilité concernant les appareils sans fil  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 38
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE)  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 39
Appendix E: Contact Information
43
Sprint Online Resource .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 43
Sprint Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Wireless-G Router for Mobile Broadband
iii
Chapter 1
Chapter 1:
Product Overview
Thank you for choosing the Linksys Wireless-G Router for
Mobile Broadband. The Router lets you access the Internet
through either your mobile broadband service (requires
a mobile broadband data card or USB adapter, available
separately), or your cable or DSL broadband service. This
access can be shared via a wireless connection or through
one of the Router’s four switched ports.
A variety of security features help to protect your data
and your privacy while online. Security features include
WPA2 (Wi-Fi Protected Access 2) security, a Stateful Packet
Inspection (SPI) firewall, and NAT technology. Configuring
the Router is easy using the Setup Wizard or provided
browser-based utility.
Top Panel
If you have a mobile broadband USB adapter, use the
Mobile USB port(s). If you have a mobile broadband data
card, use the Mobile slot.
Mobile USB Ports If the Router will connect to
a mobile broadband service, insert the mobile
broadband USB adapter (available separately)
into the USB port(s). For more information, refer
to the documentation of the mobile broadband
USB adapter.
Mobile Slot If the Router will connect to a
mobile broadband service, insert the mobile
broadband data card (available separately) into
this slot. After the data card is inserted, the eject
button will pop up. To remove the data card,
press the eject button.
Mobile Connect/Disconnect Button Press
this button to connect to and disconnect from
the mobile network. (You can also use the Basic
Setup screen of the Router’s web-based utility.)
Side Panel
Wireless-G Router for Mobile Broadband
Product Overview
USB Port Reserved for future use.
Power (Green) The Power LED lights up and
stays on while the Router is powered on.
Ethernet 1-4  (Green) These numbered LEDs,
corresponding with the numbered ports on the
Router’s back panel, serve two purposes. If the
LED is continuously lit, the Router is successfully
connected to a device through that port. It
flashes to indicate network activity over that
port.
Wireless (Green) The Wireless LED lights up
when the wireless feature is enabled. It flashes
when the Router is actively sending or receiving
data over the wireless network.
Modem Internet (Green) The Modem LED
lights up and stays on when there is a connection
made through the Modem port. It flashes to
indicate network activity over the Modem port.
Mobile Internet (Blue) The Mobile LED
flashes as the Router connects to the mobile
network. When the LED stops flashing and
stays on, then the connection is active.
If the LED flashes quickly, the Router is not
connected to the mobile network. Before you
press the Mobile Connect/Disconnect button,
make sure the mobile broadband data card or
USB adapter is already installed.
Opposite Side Panel with Antenna
Modem The Modem port is where you will
connect your cable or DSL modem.
Ethernet 1, 2, 3, 4  These Ethernet ports (1, 2, 3,
4) connect the Router to wired computers and
other Ethernet network devices.
Security Bracket The security bracket labeled
“Reset” clips onto the Router. It covers the Reset
button and the security slot on the Router’s top
panel. You can remove the security bracket to
access the Reset button.
Product Overview
Chapter 1
Reset There are two ways to reset the Router’s
factory defaults. Either press and hold the Reset
button for approximately five seconds, or restore
the defaults from the Administration > Factory
Defaults screen of the Router’s web-based
utility.
Placement Positions
Power The Power port is where you will
connect the power adapter.
Horizontal Placement
Front Panel
There are three ways to physically install the Router. The
first way is to place the Router horizontally on a surface.
The second way is to stand the Router vertically on a
surface. The third way is to mount the Router on a wall.
The Router has four rubber feet on its bottom panel. Place
the Router on a level surface near an electrical outlet.
Vertical Placement
Security Slot To protect the Router from theft,
you can attach a lock to the Router using the
security slot.
The Router has a stand on the panel opposite to the
antenna. Rotate the stand 90 degrees, and place the
Router on a level surface near an electrical outlet.
Bottom Panel
To place the Router in a vertical position, rotate the stand
90 degrees.
Wireless-G Router for Mobile Broadband
Product Overview
Chapter 1
Wall-Mounting Placement
The Router has four wall-mount slots on its back panel.
The distance between two adjacent slots is 68 mm
(2.68 inches).
Two screws are needed to mount the Router.
4-5 mm
1-1.5 mm
2.5-3.0 mm
Suggested Mounting Hardware
†Note: Mounting hardware illustrations are not
true to scale.
NOTE: Linksys is not responsible for damages
incurred by insecure wall-mounting hardware.
Follow these instructions:
1. Determine where you want to mount the Router. Make
sure that the wall you use is smooth, flat, dry, and
sturdy. Also make sure the location is within reach of
an electrical outlet.
2. Drill two holes into the wall. Make sure the holes are
68 mm (2.68 inches) apart.
3. Insert a screw into each hole and leave 3 mm
(0.12 inches) of its head exposed.
4. Maneuver the Router so two of the wall-mount slots
line up with the two screws.
5. Place the wall-mount slots over the screws and slide
the Router down until the screws fit snugly into the
wall-mount slots.
68 mm
Print this page at 100% size. Cut along
the dotted line, and place on the wall
to drill precise spacing.
Wall Mounting Template
Wireless-G Router for Mobile Broadband
Wireless Security Checklist
Chapter 2
Chapter 2:
Wireless Security Checklist
Wireless networks are convenient and easy to install, so
homes with high-speed Internet access are adopting them
at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more
vulnerable to intruders than a traditional wired network.
Like signals from your cellular or cordless phones, signals
from your wireless network can also be intercepted. Since
you cannot physically prevent someone from connecting
to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless
network name or SSID
Wireless devices have a default wireless network name
or Service Set Identifier (SSID) set by the factory. This
is the name of your wireless network, and can be up
to 32 characters in length. Linksys wireless products
use linksys as the default wireless network name. You
should change the wireless network name to something
unique to distinguish your wireless network from other
wireless networks that may exist around you, but do not
use personal information (such as your Social Security
number) because this information may be available for
anyone to see when browsing for wireless networks.
2. Change the default password
For wireless products such as access points, routers, and
gateways, you will be asked for a password when you
want to change their settings. These devices have a default
password set by the factory. The Linksys default password
is admin. Hackers know these defaults and may try to
use them to access your wireless device and change your
network settings. To thwart any unauthorized changes,
customize the device’s password so it will be hard to
guess.
3. Enable MAC address filtering
Linksys routers and gateways give you the ability to
enable Media Access Control (MAC) address filtering. The
MAC address is a unique series of numbers and letters
assigned to every networking device. With MAC address
filtering enabled, wireless network access is provided
solely for wireless devices with specific MAC addresses.
For example, you can specify the MAC address of each
computer in your home so that only those computers can
access your wireless network.
Wireless-G Router for Mobile Broadband
4. Enable encryption
Encryption protects data transmitted over a wireless
network. Wi-Fi Protected Access (WPA/WPA2) and Wired
Equivalency Privacy (WEP) offer different levels of security
for wireless communication.
A network encrypted with WPA/WPA2 is more secure
than a network encrypted with WEP, because WPA/WPA2
uses dynamic key encryption. To protect the information
as it passes over the airwaves, you should enable the
highest level of encryption supported by your network
equipment.
WEP is an older encryption standard and may be the
only option available on some older devices that do not
support WPA.
General Network Security Guidelines
Wireless network security is useless if the underlying
network is not secure.
•
Password protect all computers on the network and
individually password protect sensitive files.
•
Change passwords on a regular basis.
•
Install anti-virus software and personal firewall
software.
•
Disable file sharing (peer-to-peer). Some applications
may open file sharing without your consent and/or
knowledge.
Additional Security Tips
•
Keep wireless routers, access points, or gateways away
from exterior walls and windows.
•
Turn wireless routers, access points, or gateways
off when they are not being used (at night, during
vacations).
•
Use strong passphrases that are at least eight characters
in length. Combine letters and numbers to avoid using
standard words that can be found in the dictionary.
WEB: For more information on wireless
security, visit www.linksys.com/security
Advanced Configuration
Chapter 3
Chapter 3:
Advanced Configuration
After setting up the Router with the Setup Wizard (located
on the CD-ROM), the Router will be ready for use. However,
if you’d like to change its advanced settings, use the
Router’s web-based utility. This chapter describes each
web page of the utility and each page’s key functions. You
can access the utility via a web browser on a computer
connected to the Router.
The web-based utility has these main tabs: Setup,
Wireless, Security, Access Restrictions, Applications &
Gaming, Administration, and Status. Additional tabs will
be available after you click one of the main tabs.
NOTE: When first installing the Router, you
should use the Setup Wizard on the Setup
CD-ROM. If you want to configure advanced
settings, use this chapter to learn about the
web-based utility.
How to Access the Web-Based Utility
To access the web-based utility, launch the web browser on
your computer, and enter the Router’s default IP address,
192.168.1.1, in the Address field. Then, press Enter.
A login screen will appear. (Non-Windows XP users will see
a similar screen.) Enter admin (the default) in both the User
name and Password fields. (You can set a new password on
the Administration tab’s Management screen.) Click OK to
continue.
Setup > Basic Setup
Internet Setup
The Internet Setup section configures the Router to your
Internet connection. Most of this information can be
obtained through your ISP.
Internet Connection Type
Select the type of Internet connection your ISP provides
from the drop-down menu. These are the available types:
Login Screen
Setup > Basic Setup
The first screen that appears is the Basic Setup screen. This
allows you to change the Router’s general settings.
•
Automatic Configuration - DHCP
•
Static IP
•
PPPoE
•
PPTP
•
L2TP
•
Telstra Cable
Automatic Configuration - DHCP
By default, the Router’s Internet Connection Type is set
to Automatic Configuration - DHCP, which should be
kept only if your ISP supports DHCP or you are connecting
through a dynamic IP address. (This option usually applies
to cable connections.)
Internet Connection Type > Automatic Configuration - DHCP
Wireless-G Router for Mobile Broadband
Advanced Configuration
Chapter 3
Static IP
If you are required to use a permanent IP address to
connect to the Internet, select Static IP.
Keep Alive: Redial Period If you select this option, the
Router will periodically check your Internet connection. If
you are disconnected, then the Router will automatically
re-establish your connection. To use this option, select
Keep Alive. In the Redial Period field, specify how often
you want the Router to check the Internet connection. The
default Redial Period is 30 seconds.
PPTP
Point-to-Point Tunneling Protocol (PPTP) is a service that
applies to connections in Europe only.
Internet Connection Type > Static IP
Internet IP Address This is the Router’s IP address, when
seen from the Internet. Your ISP will provide you with the
IP address you need to specify here.
Subnet Mask This is the Router’s Subnet Mask, as seen
by users on the Internet (including your ISP). Your ISP will
provide you with the Subnet Mask.
Default Gateway Your ISP will provide you with the IP
address of the ISP server.
DNS 1-3 Your ISP will provide you with at least one DNS
(Domain Name System) server IP address.
PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol
over Ethernet) to establish Internet connections. If you are
connected to the Internet through a DSL line, check with
your ISP to see if they use PPPoE. If they do, you will have
to enable PPPoE.
Internet Connection Type > PPPoE
Username and Password Enter the Username and
Password provided by your ISP.
Service Name If provided by your ISP, enter the Service
Name.
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is 15 minutes.
Wireless-G Router for Mobile Broadband
Internet Connection Type > PPTP
Server IP Address This is the Router’s IP address, as seen
from the Internet. Your ISP will provide you with the IP
address you need to specify here.
Subnet Mask This is the Router’s Subnet Mask, as seen
by users on the Internet (including your ISP). Your ISP will
provide you with the Subnet Mask.
Default Gateway Your ISP will provide you with the IP
address of the ISP server.
Username and Password Enter the Username and
Password provided by your ISP.
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is 15 minutes.
Keep Alive: Redial Period If you select this option, the
Router will periodically check your Internet connection. If
you are disconnected, then the Router will automatically
re-establish your connection. To use this option, select
Keep Alive. In the Redial Period field, specify how often
you want the Router to check the Internet connection. The
default Redial Period is 30 seconds.
L2TP
L2TP is a service that applies to connections in Israel only.
Advanced Configuration
Chapter 3
Size When Manual is selected in the MTU field, this option
is enabled. Leave this value in the 1200 to 1500 range. The
default size depends on the Internet Connection Type:
Internet Connection Type > L2TP
Server IP Address This is the IP address of the L2TP
Server. Your ISP will provide you with the IP address you
need to specify here.
Username and Password Enter the Username and
Password provided by your ISP.
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is 15 minutes.
Keep Alive: Redial Period If you select this option, the
Router will periodically check your Internet connection. If
you are disconnected, then the Router will automatically
re-establish your connection. To use this option, select
Keep Alive. In the Redial Period field, specify how often
you want the Router to check the Internet connection. The
default Redial Period is 30 seconds.
Optional Settings
Some of these settings may be required by your ISP. Verify
with your ISP before making any changes.
Optional Settings
Host Name and Domain Name These fields allow you to
supply a host and domain name for the Router. Some ISPs,
usually cable ISPs, require these names as identification.
You may have to check with your ISP to see if your
broadband Internet service has been configured with a
host and domain name. In most cases, leaving these fields
blank will work.
MTU MTU is the Maximum Transmission Unit. It specifies
the largest packet size permitted for Internet transmission.
Select Manual if you want to manually enter the largest
packet size that is transmitted. To have the Router select
the best MTU for your Internet connection, keep the
default, Auto.
Wireless-G Router for Mobile Broadband
•
DHCP, Static IP, or Telstra: 1500
•
PPPoE: 1492
•
PPTP or L2TP: 1460
Network Setup
The Network Setup section changes the settings on the
network connected to the Router’s Ethernet ports. Wireless
setup is performed through the Wireless tab.
Router IP
This presents both the Router’s IP Address and Subnet
Mask as seen by your network.
Router IP
DHCP Server Settings
This setting determines how the clients (network devices)
use DNS/WINS.
Mode 1 - Fixed configuration (Default) Select this option
if you want the Router to advertise itself as the DNS server
to use and handle upstream changes automatically.
Mode 2 - Network Supplied Select this option if you want
the Router to pass through the DNS server values (learned
from the Modem port or mobile network) to the client,
depending on how the Router is currently connected.
NOTE: If the upstream DNS servers change
between connections, the clients may become
unable to resolve addresses because they
have valid DHCP leases that use the old server
values.
Mode 3 - Manual configuration Select this option if you
want to set arbitrary DNS/WINS values for the clients to
use. These values are not validated by the Router.
DHCP Server Settings
Network Address Server Settings (DHCP)
The settings allow you to configure the Router’s Dynamic
Host Configuration Protocol (DHCP) server function. The
Router can be used as a DHCP server for your network. A
DHCP server automatically assigns an IP address to each
10
Advanced Configuration
Chapter 3
computer on your network. If you choose to enable the
Router’s DHCP server option, make sure there is no other
DHCP server on your network.
Click Save Settings to apply your changes, or click
Cancel Changes to cancel your changes. To view the
most up-to-date information, click Refresh. To exit this
screen, click Close.
Start IP Address Enter a value for the DHCP server to
start with when issuing IP addresses. Because the Router’s
default IP address is 192.168.1.1, the Start IP Address must
be 192.168.1.2 or greater, but smaller than 192.168.1.253.
The default is 192.168.1.100.
Network Address Server Settings (DHCP)
DHCP Server DHCP is enabled by factory default. If you
already have a DHCP server on your network, or you don’t
want a DHCP server, then select Disabled (no other DHCP
features will be available).
DHCP Reservation Click this button if you want to assign
a fixed local IP address to a MAC address.
DHCP Reservation
You will see a list of DHCP clients with the following
information: Client Name, Interface, IP Address, and
MAC Address.
Maximum Number of Users Enter the maximum
number of PCs that you want the DHCP server to assign
IP addresses to. This number cannot be greater than 253.
The default is 50.
IP Address Range Displayed here is the range of available
IP addresses.
Client Lease Time The Client Lease Time is the amount
of time a network user will be allowed connection to the
Router with their current dynamic IP address. Enter the
amount of time, in minutes, that the user will be “leased”
this dynamic IP address. After the time is up, the user will
be automatically assigned a new dynamic IP address. The
default is 0 minutes, which means one day.
Static DNS 1-3 These settings are available if you
selected Mode 3 - Manual configuration for the DHCP
Server Setting. The Domain Name System (DNS) is how the
Internet translates domain or website names into Internet
addresses or URLs. Your ISP will provide you with at least
one DNS server IP address. If you wish to use another, enter
that IP address in one of these fields. You can enter up to
three DNS server IP addresses here. The Router will use
these for quicker access to functioning DNS servers.
WINS 0-1 These settings are available if you selected
Mode 3 - Manual configuration for the DHCP Server
Setting. The Windows Internet Naming Service (WINS)
manages each PC’s interaction with the Internet. If you
use a WINS server, enter that server’s IP address. You can
enter up to two WINS server IP addresses here. Otherwise,
leave these fields blank.
DHCP Reservation
•
Select Clients from DHCP Table Click the Select
check box to reserve a client’s IP address. Then click
Add Clients.
•
Manually Adding Client To manually assign an IP
address, enter the client’s name in the Enter Client
Name field. Enter the IP address you want it to have in
the Assign IP Address field. Enter its MAC address in the
To This MAC Address field. Then click Add.
Clients Already Reserved
A list of DHCP clients and their fixed local IP addresses
will be displayed at the bottom of the screen. If you
want to remove a client from this list, click Remove.
Wireless-G Router for Mobile Broadband
Time Setting
Time Zone Select the time zone in which your network
functions from this drop-down menu. (You can even
automatically adjust for daylight saving time.)
Time Setting
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
11
Advanced Configuration
Chapter 3
Setup > Mobile Network
Configure mobile network settings and view mobile
broadband status information for the Router. Some of
these settings will be automatically configured by the
Router and, in most cases, should not be changed unless
you are instructed to do so.
how often you want the Router to check the mobile network
connection. The default Redial Period is 30 seconds.
ICMP To use the default Network Time Protocol (NTP)
server, keep the default, NTP. To use a different time
server, select Custom, and enter its IP address.
Mobile Network Status
Network Name The name of the mobile network the
Router uses is displayed.
Signal Strength The strength of the mobile broadband
signal that the Router receives is displayed.
Connection Time The length of time the Router has
been connected to the mobile network since your last
connection is displayed.
Current Session Usage The amount of data that has
been sent to and received from the mobile network since
your last connection is displayed.
Data Card Status
Card Model The model number of your mobile data card
or USB adapter is displayed.
Setup > Mobile Network
Mobile Network Connection Mode
Card Firmware The firmware version of your mobile data
card or USB adapter is displayed.
Phone Number The phone number of your mobile
broadband account is displayed.
Auto Connect If you want the Router to automatically
connect to the default mobile network when it powers
on, keep the default, Auto. To manually connect to a
mobile network, select Manual. You can use the Mobile
Connect/Disconnect button on the Router to connect and
disconnect from the mobile network.
Click Refresh to update the on-screen information.
Modem Backup To use the cable/DSL WAN broadband
modem as your backup, select Enable. Otherwise, keep
the default, Disable.
The Router offers a Dynamic Domain Name System (DDNS)
feature. DDNS lets you assign a fixed host and domain
name to a dynamic Internet IP address. It is useful when
you are hosting your own website, FTP server, or other
server behind the Router.
Connect on Demand: Max Idle Time You can configure
the Router to cut the mobile network connection after
it has been inactive for a specified period of time (Max
Idle Time). If your mobile network connection has been
terminated due to inactivity, Connect on Demand enables
the Router to automatically re-establish your connection
as soon as you attempt to access the Internet again. To
use this option, select Connect on Demand. In the Max
Idle Time field, enter the number of minutes you want to
have elapsed before your mobile network connection
terminates. The default Max Idle Time is 15 minutes.
Keep Alive: Redial Period If you select this option,
the Router will periodically check your mobile network
connection. If you are disconnected, then the Router will
automatically re-establish your connection. To use this
option, select Keep Alive. In the Redial Period field, specify
Wireless-G Router for Mobile Broadband
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Setup > DDNS
Before you can use this feature, you need to sign
up for DDNS service with a DDNS service provider,
www.dyndns.org or www.TZO.com. If you do not want to
use this feature, keep the default, Disabled.
DDNS
DDNS Service
If your DDNS service is provided by DynDNS.org, then
select DynDNS.org from the drop-down menu. If your
DDNS service is provided by TZO, then select TZO.com.
The features available on the DDNS screen will vary,
depending on which DDNS service provider you use.
12
Advanced Configuration
Chapter 3
TZO.com
DynDNS.org
Setup > DDNS > TZO
Setup > DDNS > DynDNS
Username Enter the Username for your DDNS account.
E-mail Address, TZO Key, and Domain Name Enter the
settings of the account you set up with TZO.
Password Enter the Password for your DDNS account.
Internet IP Address The Router’s Internet IP address is
displayed here. Because it is dynamic, it will change.
Host Name This is the DDNS URL assigned by the DDNS
service.
Status The status of the DDNS service connection is
displayed here.
System Select the DynDNS service you use: Dynamic,
Static, or Custom. The default is Dynamic.
Update To manually trigger an update, click this button.
Mail Exchange (Optional) Enter the address of your mail
exchange server, so e-mails to your DynDNS address go to
your mail server.
Backup MX This feature allows the mail exchange server
to be a backup. To disable this feature, keep the default,
Disabled. To enable the feature, select Enabled. If you
are not sure which setting to select, keep the default,
Disabled.
Wildcard This setting enables or disables wildcards
for your host. For example, if your DDNS address is
myplace.dyndns.org and you enable wildcards, then
x.myplace.dyndns.org will work as well (x is the wildcard).
To disable wildcards, keep the default, Disabled. To enable
wildcards, select Enabled. If you are not sure which setting
to select, keep the default, Disabled.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Setup > MAC Address Clone
A MAC address is a 12-digit code assigned to a unique
piece of hardware for identification. Some ISPs will require
you to register a MAC address in order to access the
Internet. If you do not wish to re-register the MAC address
with your ISP, you may assign the MAC address you have
currently registered with your ISP to the Router with the
MAC Address Clone feature.
Internet IP Address The Router’s Internet IP address is
displayed here. Because it is dynamic, it will change.
Status The status of the DDNS service connection is
displayed here.
Update To manually trigger an update, click this button.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Setup > MAC Address Clone
MAC Address Clone
Enabled/Disabled To have the MAC Address cloned,
select Enabled.
MAC Address Enter the MAC Address registered with
your ISP here.
Wireless-G Router for Mobile Broadband
13
Advanced Configuration
Chapter 3
Clone My PC’s MAC Click this button to clone the MAC
address of the computer you are using.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Setup > Advanced Routing
This screen is used to set up the Router’s advanced
functions. Operating Mode allows you to select the
type(s) of advanced functions you use. Dynamic Routing
automatically adjusts how packets travel on your network.
Static Routing sets up a fixed route to another network
destination.
Route Entries To set up a static route between the Router
and another network, select a number from the dropdown list. Click Delete This Entry to delete a static route.
Enter Route Name Enter a name for the Route here,
using a maximum of 25 alphanumeric characters.
Destination LAN IP The Destination LAN IP is the address
of the remote network or host to which you want to assign
a static route.
Subnet Mask The Subnet Mask determines which
portion of a Destination LAN IP address is the network
portion, and which portion is the host portion.
Gateway This is the IP address of the gateway device that
allows for contact between the Router and the remote
network or host.
Interface This interface tells you whether the Destination
IP address is on the LAN & Wireless (Ethernet and wireless
networks) or the WAN (Internet).
Click Show Routing Table to view the static routes you
have already set up.
Setup > Advanced Routing
Advanced Routing
Advanced Routing > Routing Table
NAT
Enabled/Disabled If this Router is hosting your network’s
connection to the Internet, keep the default, Enabled. If
another router exists on your network, select Disabled.
When the NAT setting is disabled, dynamic routing will be
enabled.
Routing Table
Dynamic Routing (RIP)
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Enabled/Disabled This feature enables the Router to
automatically adjust to physical changes in the network’s
layout and exchange routing tables with the other router(s).
The Router determines the network packets’ route based
on the fewest number of hops between the source and
the destination. When the NAT setting is enabled, the
Dynamic Routing feature is automatically disabled. When
the NAT setting is disabled, this feature is available. Select
Enabled to use the Dynamic Routing feature.
For each route, the Destination LAN IP address, Subnet
Mask, Gateway, and Interface are displayed. Click
Refresh to update the information. Click Close to exit
this screen.
Wireless > Basic Wireless Settings
The basic settings for wireless networking are set on this
screen.
Static Routing
A static route is a pre-determined pathway that network
information must travel to reach a specific host or network.
Enter the information described below to set up a new
static route.
Wireless-G Router for Mobile Broadband
14
Advanced Configuration
Chapter 3
Wireless Security
Security Mode
Select the security method for your wireless network. If
you do not want to use wireless security, keep the default,
Disabled.
WPA Personal
Wireless > Basic Wireless Settings
Basic Wireless Settings
Network Mode From this drop-down menu, you can
select the wireless standards running on your network.
If you have Wireless-G and Wireless-B devices in your
network, keep the default, Mixed. If you have only
Wireless-G devices, select G-Only. If you have only
Wireless-B devices, select B-Only. If you do not have any
wireless devices in your network, select Disabled.
Network Name (SSID) The SSID is the network name
shared among all points in a wireless network. The
SSID must be identical for all devices in the wireless
network. It is case-sensitive and must not exceed
32 characters (use any of the characters on the keyboard).
Make sure this setting is the same for all points in your
wireless network. For added security, you should change
the default SSID (linksys) to a unique name.
Standard Channel Select the channel you want to use
for wireless networking.
SSID Broadcast When wireless clients survey the local
area for wireless networks to associate with, they will
detect the SSID broadcast by the Router. To broadcast the
Router’s SSID, keep the default, Enabled. If you do not want
to broadcast the Router’s SSID, then select Disabled.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
NOTE: If you are using WPA, always remember
that each device in your wireless network MUST
use the same WPA method and passphrase, or
else the network will not function properly.
Security Mode > WPA Personal
Encryption WPA supports two encryption methods, TKIP
and AES, with dynamic encryption keys. Select the type of
algorithm, TKIP or AES. The default is TKIP.
Passphrase Enter a Passphrase of 8-63 characters.
Key Renewal Enter a Key Renewal period, which instructs
the Router how often it should change the encryption
keys. The default is 3600 seconds.
WPA2 Personal
Wireless > Wireless Security
The Wireless Security screen configures the security of
your wireless network. There are six wireless security
mode options supported by the Router: WPA Personal,
WPA2 Personal, WPA Enterprise, WPA2 Enterprise, RADIUS,
and WEP. (WPA stands for Wi-Fi Protected Setup, which
is a security method stronger than WEP encryption. WEP
stands for Wired Equivalent Privacy, while RADIUS stands
for Remote Authentication Dial-In User Service.) These
six are briefly discussed here. For detailed instructions
on configuring wireless security for the Router, refer to
“Chapter 2: Wireless Security.”
Security Mode > WPA2 Personal
Encryption WPA2 supports two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
type of algorithm, AES or AES or TKIP. The default is AES
or TKIP.
Passphrase Enter a Passphrase of 8-63 characters.
Wireless-G Router for Mobile Broadband
15
Advanced Configuration
Chapter 3
Key Renewal Enter a Key Renewal period, which instructs
the Router how often it should change the encryption
keys. The default is 3600 seconds.
WPA Enterprise
This option features WPA used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Router.)
Encryption WPA2 supports two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
type of algorithm, AES or AES or TKIP. The default is AES
or TKIP.
RADIUS Server Enter the IP address of the RADIUS
server.
RADIUS Port Enter the port number of the RADIUS
server. The default is 1812.
Shared Secret Enter the key shared between the Router
and the server.
Key Renewal Enter a Key Renewal period, which instructs
the Router how often it should change the encryption
keys. The default is 3600 seconds.
RADIUS
This option features WEP used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Router.)
Security Mode > WPA Enterprise
Encryption WPA supports two encryption methods, TKIP
and AES, with dynamic encryption keys. Select the type of
algorithm, TKIP or AES. The default is TKIP.
RADIUS Server Enter the IP address of the RADIUS
server.
RADIUS Port Enter the port number of the RADIUS
server. The default is 1812.
Shared Secret Enter the key shared between the Router
and the server.
Key Renewal Enter a Key Renewal period, which instructs
the Router how often it should change the encryption
keys. The default Key Renewal period is 3600 seconds.
WPA2 Enterprise
This option features WPA2 used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Router.)
Security Mode > RADIUS
IMPORTANT: If you are using WEP encryption,
always remember that each device in your
wireless network MUST use the same WEP
encryption method and encryption key, or else
your wireless network will not function properly.
RADIUS Server Enter the IP address of the RADIUS
server.
RADIUS Port Enter the port number of the RADIUS
server. The default is 1812.
Shared Key Enter the key shared between the Router
and the server.
Encryption Select a level of WEP encryption,
40/64 bits (10 hex digits) or 104/128 bits (26 hex digits).
The default is 40/64 bits (10 hex digits).
Security Mode > WPA2 Enterprise
Wireless-G Router for Mobile Broadband
Passphrase Enter a Passphrase to automatically generate
WEP keys. Then click Generate.
16
Advanced Configuration
Chapter 3
Key 1-4  If you did not enter a Passphrase, enter the WEP
key(s) manually.
TX Key Select which TX (Transmit) Key to use. The default
is 1.
WEP
WEP is a basic encryption method, which is not as secure
as WPA.
Wireless > Wireless MAC Filter
Security Mode > WEP
Encryption Select a level of WEP encryption,
40/64 bits (10 hex digits) or 104/128 bits (26 hex digits).
The default is 40/64 bits (10 hex digits).
Passphrase Enter a Passphrase to automatically generate
WEP keys. Then click Generate.
Key 1-4  If you did not enter a Passphrase, enter the WEP
key(s) manually.
TX Key Select which TX (Transmit) Key to use. The default
is 1.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Wireless MAC Filter
Wireless access can be filtered by using the MAC addresses of
the wireless devices transmitting within your network’s radius.
Wireless MAC Filter
Enabled/Disabled To filter wireless users by MAC Address,
either permitting or blocking access, select Enabled. If you
do not wish to filter users by MAC Address, keep the default,
Disabled.
Access Restriction
Prevent Select this to block wireless access by MAC
Address. This button is selected by default.
Permit Select this to allow wireless access by MAC
Address. This button is not selected by default.
MAC Address Filter List
Wireless Client List Click this to open the Wireless Client
List screen.
Wireless Client List
Wireless-G Router for Mobile Broadband
17
Advanced Configuration
Chapter 3
Wireless Client List
This screen shows computers and other devices on
the wireless network. The list can be sorted by Client
Name, Interface, IP Address, MAC Address, and Status.
Select Save to MAC Address Filter List for any device
you want to add to the MAC Address Filter List. Then
click Add.
To retrieve the most up-to-date information, click
Refresh. To exit this screen and return to the Wireless
MAC Filter screen, click Close.
MAC 01-50 Enter the MAC addresses of the devices
whose wireless access you want to block or allow.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Advanced Wireless Settings
This Advanced Wireless Settings screen is used to set up
the Router’s advanced wireless functions. These settings
should only be adjusted by an expert administrator as
incorrect settings can reduce wireless performance.
use a WEP key for authentication. Select Shared Key to
only use Shared Key authentication.
Basic Rate The Basic Rate setting is not actually one rate
of transmission but a series of rates at which the Router
can transmit. The Router will advertise its Basic Rate to
the other wireless devices in your network, so they know
which rates will be used. The Router will also advertise that
it will automatically select the best rate for transmission.
The default is Default, when the Router can transmit at
all standard wireless rates (1-2Mbps, 5.5Mbps, 11Mbps,
18Mbps, and 24Mbps). Other options are 1-2Mbps, for
use with older wireless technology, and All, when the
Router can transmit at all wireless rates. The Basic Rate
is not the actual rate of data transmission. If you want to
specify the Router’s rate of data transmission, configure
the Transmission Rate setting.
Transmission Rate The rate of data transmission should
be set depending on the speed of your wireless network.
You can select from a range of transmission speeds, or you
can select Auto to have the Router automatically use the
fastest possible data rate and enable the Auto-Fallback
feature. Auto-Fallback will negotiate the best possible
connection speed between the Router and a wireless
client. The default is Auto.
CTS Protection Mode The Router will automatically
use CTS (Clear-To-Send) Protection Mode when your
Wireless-N and Wireless-G products are experiencing
severe problems and are not able to transmit to the
Router in an environment with heavy 802.11b traffic. This
function boosts the Router’s ability to catch all WirelessN and Wireless-G transmissions but will severely decrease
performance. The default is Auto.
Wireless > Advanced Wireless Settings
Advanced Wireless
AP Isolation This isolates all wireless clients and wireless
devices on your network from each other. Wireless devices
will be able to communicate with the Router but not
with each other. To use this function, select Enabled. AP
Isolation is disabled by default.
Frame Burst Enabling this option should provide your
network with greater performance, depending on the
manufacturer of your wireless products. To use this option,
keep the default, Enabled. Otherwise, select Disabled.
Authentication Type The default is set to Auto, which
allows either Open System or Shared Key authentication
to be used. With Open System authentication, the sender
and the recipient do NOT use a WEP key for authentication.
With Shared Key authentication, the sender and recipient
Wireless-G Router for Mobile Broadband
Beacon Interval Enter a value between 1 and 65,535
milliseconds. The Beacon Interval value indicates the
frequency interval of the beacon. A beacon is a packet
broadcast by the Router to synchronize the wireless
network. The default is 100.
DTIM Interval This value, between 1 and 255, indicates
the interval of the Delivery Traffic Indication Message
(DTIM). A DTIM field is a countdown field informing
clients of the next window for listening to broadcast
and multicast messages. When the Router has buffered
broadcast or multicast messages for associated clients, it
sends the next DTIM with a DTIM Interval value. Its clients
hear the beacons and awaken to receive the broadcast
and multicast messages. The default is 1.
Fragmentation Threshold This value specifies the
maximum size for a packet before data is fragmented
into multiple packets. If you experience a high packet
error rate, you may slightly increase the Fragmentation
Threshold. Setting the Fragmentation Threshold too low
may result in poor network performance. Only minor
reduction of the default value is recommended. In most
cases, it should remain at its default of 2346.
18
Advanced Configuration
Chapter 3
RTS Threshold Should you encounter inconsistent data
flow, only minor reduction of the default value, 2347, is
recommended. If a network packet is smaller than the
preset RTS threshold size, the RTS/CTS mechanism will
not be enabled. The Router sends Request to Send (RTS)
frames to a particular receiving station and negotiates
the sending of a data frame. After receiving an RTS, the
wireless station responds with a Clear to Send (CTS) frame
to acknowledge the right to begin transmission. The RTS
Threshold value should remain at its default value of
2347.
Filter IDENT (Port 113) This feature keeps port 113 from
being scanned by devices outside of your local network.
This feature is selected by default. Deselect this feature to
disable it.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Java Java is a programming language for websites. If you
deny Java, you run the risk of not having access to Internet
sites created using this programming language. Select
this feature to enable Java filtering. Deselect the feature
to allow Java usage.
Security > Firewall
The Firewall screen is used to configure a firewall that can
filter out various types of unwanted traffic on the Router’s
local network.
Web Filter
Proxy Use of WAN proxy servers may compromise the
Gateway’s security. Denying Proxy will disable access to
any WAN proxy servers. Select this feature to enable proxy
filtering. Deselect the feature to allow proxy access.
ActiveX ActiveX is a programming language for websites.
If you deny ActiveX, you run the risk of not having access to
Internet sites created using this programming language.
Select this feature to enable ActiveX filtering. Deselect the
feature to allow ActiveX usage.
Cookies A cookie is data stored on your computer and
used by Internet sites when you interact with them. Select
this feature to filter cookies. Deselect the feature to allow
cookie usage.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Security > VPN
Security > Firewall
Firewall
The VPN screen allows you to enable VPN tunnels using
IPSec, PPTP, or L2TP protocols to pass through the Router’s
firewall. You can also configure up to five IPSec VPN
tunnels.
SPI Firewall Protection To use firewall protection, keep
the default, Enabled. To turn off firewall protection, select
Disabled.
Internet Filter
Filter Anonymous Internet Requests This feature makes
it more difficult for outside users to work their way into
your network. This feature is selected by default. Deselect
the feature to allow anonymous Internet requests.
Filter Multicast Multicasting allows for multiple
transmissions to specific recipients at the same time. If
multicasting is permitted, then the Router will allow IP
multicast packets to be forwarded to the appropriate
computers. Select this feature to filter multicasting. This
feature is not selected by default.
Filter Internet NAT Redirection This feature uses port
forwarding to block access to local servers from local
networked computers. Select this feature to filter Internet
NAT redirection. It is not selected by default.
Wireless-G Router for Mobile Broadband
19
Advanced Configuration
Chapter 3
VPN Settings Summary
At the top of the screen is the WAN IP address of the
Router. The screen also displays the No., Tunnel Name,
Status, Local Group, Remote Group, Remote Gateway,
and Security Method of the VPN tunnels. Click Refresh to
update the information.
VPN > VPN Settings Summary
IPSec VPN Tunnel Select Enabled to enable the IPSec
VPN tunnel.
Tunnel Name Enter a descriptive name. This lets you
identify multiple tunnels and does not have to match the
name used at the other end of the tunnel.
Local Secure Group
The Local Secure Group is the computer(s) on your network
that can access the tunnel. Specify these computers using
one of the following:
IP Addr. Select this option to specify a single host.
•
Security > VPN
VPN Passthrough
IPSec Passthrough Internet Protocol Security (IPSec) is
a suite of protocols used to implement secure exchange
of packets at the IP layer. To allow IPSec tunnels to pass
through the Router, keep the default, Enabled.
PPTP Passthrough Point-to-Point Tunneling Protocol
(PPTP) allows the Point-to-Point Protocol (PPP) to be
tunneled through an IP network. To allow PPTP tunnels to
pass through the Router, keep the default, Enabled.
L2TP Passthrough Layer 2 Tunneling Protocol is the
method used to enable Point-to-Point sessions via the
Internet on the Layer 2 level. To allow L2TP tunnels to pass
through the Router, keep the default, Enabled.
IPSec VPN Tunnel
The Router can create an IPSec tunnel or channel between
two endpoints, so that the data or information between
these endpoints is secure.
Select Tunnel Entry To establish this tunnel, select the
tunnel you wish to create. It is possible to create up to five
simultaneous tunnels.
To delete a tunnel entry, select the tunnel, and then
click Delete. To view a summary of the settings, click
Summary.
Wireless-G Router for Mobile Broadband
IP Address Enter the host’s IP address.
Subnet Select this option to give an entire local network
access to the tunnel.
•
IP Enter the IP address.
•
Mask Enter the subnet mask.
Remote Secure Group
The Remote Secure Group is the computer(s) on the
remote end of the tunnel that can access the tunnel.
Specify these computers using one of the following:
IP Addr. Select this option to specify a single host.
•
IP Address Enter the host’s public IP address.
Subnet Select this option to give an entire remote subnet
access to the tunnel.
•
IP Enter the IP address.
•
Mask Enter the subnet mask.
Host Select this option to use the Remote Security
Gateway settings.
Any Select this option to have the Router accept requests
from any IP address.
Remote Security Gateway
The Remote Security Gateway is the VPN device on the
remote end of the VPN tunnel. The remote VPN device can
be another router, a VPN Server, or a computer with VPN
client software that supports IPSec. Specify the remote
VPN device using one of the following:
20

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Print high-res
XMP Toolkit                     : 3.1-702
Modify Date                     : 2007:10:17 08:37:13-07:00
Create Date                     : 2007:10:17 08:36:07-07:00
Metadata Date                   : 2007:10:17 08:37:13-07:00
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Format                          : application/pdf
Title                           : Linksys WRT54G3GV2-ST User Guide
Creator                         : Linksys
Document ID                     : uuid:cb11b798-3598-4f21-9fb5-d3b5f102edc0
Instance ID                     : uuid:14b6d09c-2fa0-4ea9-af46-229d3d2973ee
Producer                        : Adobe PDF Library 7.0
Page Count                      : 21
Author                          : Linksys

EXIF Metadata provided by EXIF.tools