LITE ON TECHNOLOGY CR8702K JUKEBLOX NETWORKED MEDIA MODULE User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1433733
Application ID	DvLLYfzQEhAj1Qb0g8NkNg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.59kB (569934 bits)
Date Submitted	2011-03-18 00:00:00
Date Available	2011-03-21 00:00:00
Creation Date	2011-03-08 10:16:49
Producing Software	Acrobat Distiller 9.4.2 (Windows)
Document Lastmod	2011-03-09 13:36:38
Document Title	Microsoft Word - dat_CR860_CR870_2_14_datasheet.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Jo

Data Sheet: CR Series
JukeBlox Networked Media Modules
JukeBlox Networked Media Module
CR Series CR870-2K
Datasheet
Complete audio networking system on a small module
Integrated Ethernet + USB2.0
WiFi-certified 802.11b/g (optional)
Built-in PIFA antenna
DAB radio receiver (optional)
Glueless audio, video and control ports
FCC certified
CONFIDENTIAL
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 1 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Introduction
The CR-series module is a single-board networked media player module, based on BridgeCo’s DM860
and DM870 media processors, and enables fast product developments with Ethernet, USB and
optional WiFi and/or DAB radio connectivity. The module connects to standard legacy components in
various audio, video/LCD and control formats.
Block Diagram
JukeBlox Networked Media Module – CR Series
3.3V
Reset In
Reset Out
100B-T
RJ-45
USB
USB
(Host)
5V
3x6bit RGB
LP
CCIR-656
A/D, D/A
S/PDIF
serial control
shift register
IC control
IR sensor
reset signals
analog mute
I2C bus
4/8bit MMC
Stereo Out
Video Out
Audio I/O
2 x UART
SPI Ctrl.
max. 20 GPIOs
RMII
1 GB
NAND flash
Mem
256 Mbit
SDRAM
802.11
802.11
RF amp
(optional)
USB
SSM
DAC
AV
Ports
UART
SPI
GPIO
3.3V (RTC)
RTC
SuperCap
dat_CR860_CR870_2_14_datasheet.doc
NAND
LCD
Display
HP out
24.000 MHz
RST
Ethernet
PHY
SD-Card
JTAG
DM860
or
DM870
1.2V
CONFIDENTIAL
PIFA
Antenna
Switcher
1.9V
AV
Ports
DAB
32.768 kHz
Version 2.14 – June 10th 2010 - Page 2 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Overview
Top View of CR870-2A version
antenna
connector
SDRAM
FLASH
(optional socket)
PIFA
antenna
802.11b/g
front-end
DAB
BridgeCo
processor
Ethernet
Bottom View of CR870-2A version
LCD
connector
DAB
connector
Media
connector
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 3 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Top View of CR870-2G version
Bottom View of CR870-2B, CR870-2C, CR870-2G versions
Please note that
production version does
not have exposed solder
on the underside of the
mounting holes.
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 4 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Ordering Guide
WiFi
Part
Number
Ethernet
USB
RealTime
Clock
DAB /
DAB+ /
DMB Audio
LCD
Incl.
connector
Incl.
connector
PIFA
Antenna
Ext.
Antenna
UFL
Conn.
(X)*
BridgeCo ICs
Contains
shield
CR870-2A
DM870+T6201
CR870-2B
DM870+T6201
CR870-2C
DM870+T6201
CR870-2D
DM870+T6201
CR870-2F
DM870+T6201
SDRAM
32MB
32MB
32MB
(X)*
32MB
(X)*
16MB
16MB
16MB
CR870-2G
DM870+T6201
CR870-2H
DM870+T6201
CR870-2I
DM870+T6201
CR870-2J
DM870+T6201
CR870-2K
DM870+T6201
CR860-2A
DM860
n/a
CR860-2B
DM860
n/a
32MB
No on-board
1.9V
32MB
16MB
n/a
32MB
n/a
32MB
* Connector on board, but not enabled
Electrical Specifications
Parameter
Input Voltage
Power
Consumption
State
Reset
State
Model
Component
DAB
VIN
CR870
int 1.9V
CR860
CR870
int 1.9V
CR870
ext 1.9V
Operating
CR860
Symbol
VIN
CR870
ext 1.9V
WLAN
Operating
Voltage
Main
Main
3.3V
1.2V
3.3V
1.2V
1.9V
3.3V
1.2V
3.3V
1.2V
3.3V
1.2V
1.9V
3.3V
1.2V
PIN3.3
PIN1.2
PIN3.3
PIN1.2
PIN1.9
PIN3.3
PIN1.2
PIN3.3
PIN1.2
PIN3.3
PIN1.2
PIN1.9
PIN3.3
PIN1.2
min.
+2.97
+1.08
+1.62
+2.97
+1.35
typ.
+3.3
+1.2
+1.8
+3.3
+1.5
230
45
165
45
35
145
45
1750
600
825
600
535
760
600
max.
+3.63
+1.32
+1.98
+3.63
+1.65
300
60
215
60
50
190
60
2275
800
1075
800
700
990
800
Units
mW
mW
mW
mW
mW
mW
mW
mW
mW
mW
mW
mW
mW
mW
Note: The maximum power consumption values are 30% larger than the typical values.
The maximum values are intended to be used for power supply sizing calculations.
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 5 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Absolute Maximum Ratings
Parameter
3.3V Supply Voltage
1.2V Supply Voltage
Logic Input Voltage
Logic Output Voltage
Component
Main
Min
-0.5
-0.5
-0.5
-0.5
Max
4.6
1.8
4.6
Units
Operating Conditions
Parameter
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Storage Temperature Cycle Test 24 hrs
Min
10
-10
10
-10
Max
+70
90 (non condensing)
+75
95 (non condensing)
+75
Units
°C
%RH
°C
%RH
°C
WiFi Specification (CR870 only)
Feature
WLAN Standards
Frequency Band
Modulation
Transmission Speed
Tx Power
Power-on Ramp
RF Carrier Suppression
TX EVM
Rx Sensitivity
(incl. CE2 Mother board)
Throughput Rate
(measured for each
module)
Description
IEEE 802.11b
IEEE 802.11g
2.412 – 2.472 GHz (2.4GHz ISM Band, 13 Channels)
Channel 1 - Channel 13
North America, Japan Telec, Europe ETSI
802.11b mode (DS-SS: IEEE 802.11b)
802.11g mode (OFDM: IEEE 802.11g)
802.11b mode
11Mbps, 5.5Mbps, 1Mbps
802.11g mode
54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps
802.11b mode (16.5dBm, +/-1dBm)
802.11g mode (21dBm, +/-1dBm)
< 2us
< 15dBc
< -5dB @ 6Mbps
< -25dB @ 54Mbps
802.11b mode
=<-88dBm @ 1Mbps, =<-85dBm @ 5.5Mbps, =<-83dBm @ 11Mbps
802.11g mode
=<-86dBm @ 6Mbps, =<-75dBm @ 36Mbps, =<-69dBm @ 54Mbps
See factory test specification
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 6 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Regulatory compliance
Description
Electromagnetic Compatibility
(Prescan)
Country
USA
Europe
Radio Regulations (CM870
only)
TBD
Compliance
FCC CFR47 Part15B
EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
TBD
RoHS
Uses only RoHS compliant components
Environmental Test
Withstands 4 hours at 70°C, 90% RH
ESD and Transient Test (Applies to LAN and USB external
connections only)
ESD: +/- 2kV operation, +/- 4kV no destruction (part of CE test)
Fast electrical transients: +/- 500V operation, +/- 1000V no destruction (part of CE test)
Magnetic Field Test
Passes EN55022 and EN55024 (part of CE test)
MTBF
>10000 hours
Mechanical Specifications
Passes drop test according to I.E.C. 68-2-32, height 100 cm, 1 corner, 6 faces.
Passes vibration test with sine, vertical, 60 minutes, 600 to 18000 cpm, 1G
Module Quality
Defect Rate: 7 months <0.5% failures, 14 months <1% failures
AQL CR=0, MA=0.4, MI=0.4
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 7 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Board Dimensions
Top View and Side View
Bottom View (showing connector locations)
Note:
1.
2.
3.
4.
5.
6.
7.
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
All dimensions are measured in millimetres (mm).
PCB’s thickness: 1.00 +/- 0.10mm
Tolerance: +/-0.10mm
Outline Tolerance: +/-0.10mm
NPTH Hole: +/-0.05mm
PTH Hole: +/-0.075mm
Connector positions, board dimensions, mounting
hole positions and sizes are the same for all module
variants.
Version 2.14 – June 10th 2010 - Page 8 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Top and Side View of CR870-2G (no PIFA antenna)
Module weight
CR860: 25g
CR870: 25g
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 9 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Connectors
WLAN UFL Antenna Connector (optional)
One coaxial antenna connector is provided as an alternative to the built-in PIFA antenna. The choice
between using the PIFA antenna or using the coaxial socket is a build option, determined by the
position of a surface mount capacitor on the module PCB. Please see ordering guide for build option
details.
The surface-mount receptacle parts:
Hirose
U.FL-R-SMT (CL No. 331-0471-0)
Coaxial antenna connector dimensions
Module Connectors
The CR860/870 module uses 3 female board-to-board connectors as interfaces to the product main
board. The connectors needed on the product main board are male type, with the part numbers as
shown in the table below.
Connector
Number
Connector
Purpose
J1
J2
J3
LCD
Media
DAB
Connector
Type
B2B
Connector
dat_CR860_CR870_2_14_datasheet.doc
Number
of Pins
Pin
Configuration
Male Mating Connector Part
Numbers
30
120
40
2 x 15 x 0.5mm
2 x 60 x 0.5mm
2 x 20 x 0.5mm
14-5046-030-145-829+ (Kyocera)
14-5046-120-145-829+ (Kyocera)
14-5046-040-145-829+ (Kyocera)
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 10 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
The pinout and signal names are shown on the next page. The following table provides an overview
for the most important control and interface signals.
Key Connections
Signal(s)
Connector ID
Pin
Number(s)
Description
VIN
J2
J2
J3
J3
J3
3, 4, 5, 6
9, 10, 11, 12
4, 6
10
12
Input
Input
Input
Input
Input
SPI_DOUT
SPI_DIN
SPI_CLK
SPI_NCS0, 1
SPI_REQ
J2
J2
J2
J2
J2
25
27
29
30, 32
64
SPI bus from DM870’s SPI controller.
RXD1, TXD1
J2
35, 37
3.3V logic level UART I/Os for the debug UART.
Provide external RS-232 transceiver to connect to a PC’s
COM port.
NRESET_MOD
J2
34
NPD_RF
J2
119
Low-active input to reset the module;
internal 10K pull-up
Low-active input to shut down the power for the
802.11 Rf part;
internal 10K pull-up
AOUTLP/AOUTLN
AOUTRP/AOUTRN
J2
J2
63, 65
60, 58
Differential stereo output from PWM-DAC.
BIST activate
J2
48
Factory Reset
J2
68
IR input
J2
70
ETH_NRESET
J2
72
SDA, SCL
J2
73, 75
ETH_LED_ACT
ETH_LED_SPEED
J2
J2
100
102
dat_CR860_CR870_2_14_datasheet.doc
voltage;
voltage;
voltage;
voltage;
voltage;
+3.3V
+1.2V
+1.8V
+3.3V
+1.5V
PDOUT1 signal used as SPI_REQ for eDMP applications
Low-active input to invoke the production BIST;
DM870-internal pull-up
High-active input to reset the configuration;
DM870-internal pull-down
Infrared sensor input. This is a Schmitt-Trigger input
and can handle interrupt inputs with slow slopes.
Low-active reset for the on-board Ethernet phy. This
output is driven by the DM870 and is not suited for
other purpose.
I2C bus created by GPIO-14 and GPIO-13.
No internal pull-ups; if I2C is to be used, please add the
proper external pull-up resistors.
3.3V push-pull outputs (max. ±12mA) to drive the
Ethernet LEDs.
A low-level indicates 100Mbps mode and activity
respectively.
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 11 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Detailed Connector PIN Descriptions
J2 – Media Connector
Function GPIO Signal
F4
SPI
Debug UART
SPI_DOUT
SPI_DIN
SPI_CLK
TXD0
RXD0
RXD1
TXD1
PIN Number
IC PIN Power
GND
VIN (+3.3V)
VIN (+3.3V)
GND
VIN (+1.2V)
VIN (+1.2V)
GND
VIN_OUTSIDE (+1.9V)
GND
3V3RTC
GND
GND
E17
F17
D17
C17
A18
B17
A17
GND
SPI_E_NCS
SPI_E_SDI
GPIO-11
GPIO-09
SSMD7
SSMD5
SSMD3
SSMD0
SSMCLK
SSMCP
C16
A16
B15
B14
C13
C12
USB_DN
USB_DP
USBVBUSDRV
A1
B1
AOUTLP
AOUTLN
H3
J3
GND
USB
GND
GND
GPIO-16
GPIO-18
GPIO-14
GPIO-13
IRQ input
I2C SDA
I2C SCL
Video Output
A23
A22
AV3CTRL1
AV3CTRL0
AV0CTRL2
AV0CTRL1
AV0CLK
AV0DATA3
AV0DATA2
AV0DATA1
AV0DATA0
K20
K19
V1
V2
K3
L3
N1
N2
N3
P1
P2
AV2CTRL0
AV2DATA3
AV2DATA2
AV2DATA1
AV2DATA0
T2
T3
T4
U1
U2
GND
LRCK
A/D data
A/D data
D/A data
D/A data
GND
Ethernet
ETH_RXETH_RX+
ETH_CT
ETH_TXETH_TX+
GND
GPIO-15
NWAIT
NPD_RF
N18
dat_CR860_CR870_2_14_datasheet.doc
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
CONFIDENTIAL
Power
IC PIN Signal
GPIO Function
GND
VIN (+3.3V)
VIN (+3.3V)
GND
VIN (+1.2V)
VIN (+1.2V)
GND
VIN_OUTSIDE (+1.9V)
GND
GND
B20
A20
B19
A19
D16
D15
B16
C15
A15
C14
A14
C11
M18
L18
TMS
TCK
TDI
TDO
SPI_NCS0
SPI_NCS1
NRESET_MOD
SSMD6
SSMD4
SSMD2
SSMD1
SSMCMD
SSMWP
NCS3
NCS2
JTAG
SPI
GPIO-10 SPI_E_CLK
GPIO-08 SPI_E_SDO
GPIO-17 BIST activate
GPIO-19
GND
USB
USB_VBUS
GND
K2
J2
AOUTRN
AOUTRP
L1
L2
M1
M2
U3
M3
P3
R1
R2
R3
PDOUT1
VCO1
PDOUT0
VCO0
AV3CLK
AV0CTRL0
AV1DATA3
AV1DATA2
AV1DATA1
AV1DATA0
T1
AV2CTRL1
MCLK
R4
AV2CLK
SCLK
W2
Y1
AV4DATA1
AV4DATA0
SPDIF output
SPDIF input
GND
GPIO-06
GPIO-07
GPIO-04
GPIO-05
GPIO-12
SPI_REQ
Factory reset
IR input
ETH NRESET
Video Output
GND
GND
GND
GND
Y14
W14
V10
V11
W10
Y10
W12
Y12
ETH_LED_ACT
ETH_LED_SPEED
MIICRS
MIICOL
MIITXER
MIITXCLK
MIITXD0
MIITXD1
MIIRXD0
MIIRXD1
Ethernet
GPIO-00
GPIO-01
GPIO-02
GPIO-03
GND
Version 2.14 – June 10th 2010 - Page 12 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
J1 – LCD Connector
Function GPIO Signal
PIN Number
IC PIN Power
GND
LCD Interface
LCDD0
LCDD2
LCDD4
LCDD6
LCDD8
LCDD10
LCDD12
LCDD14
LCDD16
Y7
V7
W6
U6
W5
U5
W4
U4
W3
LCD Interface
LCDCLK
LCDCTRL1
LCDCTRL3
Y9
Y8
V8
GND
GND
11
13
15
17
19
21
23
25
27
29
10
12
14
16
18
20
22
24
26
28
30
Power IC PIN Signal GPIO Function
GND
W7
Y6
V6
Y5
V5
Y4
V4
Y3
Y2
LCDD1
LCDD3
LCDD5
LCDD7
LCDD9
LCDD11
LCDD13
LCDD15
LCDD17
LCD Interface
W9
W8
LCDCTRL0
LCDCTRL2
LCD Interface
GND
GND
GND
J3 – DAB Connector
Function GPIO Signal
PNM3030E PIN
Power
GND
RESETB
RF_I2C_CK
I2C_SDA_DAB
I2C_SCL_DAB
30
39
46
GND
SPI
TEST_1
DAB_SPI_MOSI
DAB_SPI_CSB
79
19
17
GND
GND
GND
GND
MPEG_ERR
MPEG_SYNC
MPEG_DAT7
MPEG_DAT5
MPEG_DAT3
MPEG_DAT1
51
52
10
GND
PIN Number
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Power
PNM3030E PIN Signal
GPIO Function
GND
VIN (+1.8V)
VIN (+1.8V)
40
RF_I2C_DT
80
78
18
16
TEST_2
TEST_0
DAB_SPI_CLK
DAB_SPI_MISO
14
15
47
48
53
INT_0
INT_1
MPEG_CLK
MPEG_VAL
MPEG_DAT6
MPEG_DAT4
MPEG_DAT2
MPEG_DAT0
VIN (+3.3V)
VIN (+1.5V)
SPI
GND
GND
Application Notes
There are strict power sequencing and reset timing requirements. Please see DM870 IC data sheet,
Sections 3.1 and 3.2, filename: dat_DM870_16_datasheet.pdf, or later version.
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 13 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
Revision Control
Revision
Date / Author
Remarks
V2.14
June 10, 2010 / SHs
•
Updated Frequency Band entry in “WiFi Specification” table
V2.13
June 6, 2010 / SHs
•
Updated “Ordering Guide” table
V2.12
May 27, 2010 / SHs
•
•
Updated TX EVM entry in “WiFi Specifications” table
Updated Power Consumption entries in “Electrical Specifications”
table
Added Note to “Electrical Specifications” table
Removed box from “Bottom View of CR870-2C version” photo
Updated “Bottom View of CR870-2C version” title to “Bottom
View of CR870-2B, CR870-2C, CR870-2G versions”
Added “Top View of CR870-2G version” photo
Updated “Top View” title to “Top View of CR870-2A version”
Updated “Bottom View” to “Bottom View of CR870-2A version”
Updated Notes in Board Dimensions section
Added “Top and Side View of CR870-2G” drawings
Updated Module Weight titles
•
•
•
•
•
•
•
•
•
V2.11
April 25, 2010 / SHs
•
Updated Power Consumption/WLAN
“Electrical Specifications” table
V2.10
April 10, 2010 / SHs
•
Corrected “Module Connectors” section text to say “female
board-to-board connectors”
Updated Module Connectors table with correct “Male” Mating
Connector Part Numbers
•
V2.9
March 22, 2010 / SHs
•
•
•
•
•
•
•
•
•
Operating
entry
in
Renamed “WLAN Antenna Connectors” section to “WLAN UFL
Antenna Connector”
In the “WLAN Antenna Connectors” table, “receptible” became
“receptacle”
CR870-2G option and External Antenna UFL connector column
added to Ordering Guide
Power Consumption values added to Electrical Specifications
table
Added Absolute Maximum Ratings table
Added Application Notes section
NREST became NRESET_MOD for Pin 34 in Key Connections
table
SPI_REQ row added to Key Connections table
SPI_REQ added to Function column of Pin 64 in J2-Media
Connector table
V2.8
Feb. 24, 2010 / SHs
•
Added “Bottom View of CR870-2C version” image to “Overview”
section
V2.7
Feb. 16, 2010 / SHs
•
Updated “Module Connectors” table
V2.6
Feb. 15, 2010 / SHs
•
Updated “Ordering Guide” table
V2.5
Feb. 10, 2010 / SHs
•
•
•
Updated “Ordering Guide” table
Added new coaxial text in “WLAN Antenna Connectors” section
Added manufacturer name to “Module Connectors” table
V2.4
Feb. 08, 2010 / SHs
•
Updated Rx Sensitivity description in “WiFi Specification” table
V2.3
Feb. 03, 2010 / SHs
•
•
•
“Key Connectors” table title changed to “Key Connections”
Updated entries in “Key Connections” table
Updated pins 1, 2, 25, 27, 58 & 60 in “J2 – Media Connector”
table
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 14 of 15
Data Sheet: CR Series
JukeBlox Networked Media Modules
V2.2
Feb. 02, 2010 / SHs
•
•
Added new items to “WiFi Specification” table
Amended Block Diagram to show input of 1.2V instead of 1.8V
V2.1
Jan. 04, 2010 / SHs
•
•
•
•
•
Updated header layout
Removed “CR860/CR870” from data sheet title
Left justified Key Features list on front page
New Ordering Guide table
Updated Module Weights
V2.0
Jan. 02, 2010 / JWs and
SHs
•
•
•
New header and footer layout
Fit front and back Overview images onto one page
Bulletise Revision Control table
V1.1
Dec. 18, 2009 / SHs
•
Changed Core Module name to “JukeBlox Networked Media
Module(CR Series)”
Front page revisions: removed front and back images of board;
inserted angled image of board; moved Key Features list to
front page
Moved Disclaimers page to end of document
Replaced previous board images (front and back) in Overview
section with better quality images
Added box and label to BridgeCo processor in Overview images
Revised Ordering Guide
Reduced Board Dimension drawings to fit on one page
Added mating connector part numbers to Module Connectors
section.
•
•
•
•
•
•
•
V1.0
Dec. 9, 2009 / SHs
Initial version
© 2010 by BridgeCo Inc
All rights reserved. This document is the sole property of BridgeCo. It contains information
proprietary to BridgeCo. Reproduction or duplication by any means of any portion of this document
without the prior written consent of BridgeCo is expressly forbidden.
Trademarks
The names of products of BridgeCo or other vendors and suppliers appearing in this document may
be trademarks or service marks of their respective owners which may be registered in some
jurisdictions.
Warranty Limitations
BridgeCo assumes no responsibility for inaccuracies, errors, or omissions in this document. BridgeCo
assumes no responsibility for the use of this information, and all use of such information shall be
entirely at the user’s own risk. Prices and specifications are subject to change without notice.
Module Revision History
To be determined.
dat_CR860_CR870_2_14_datasheet.doc
CONFIDENTIAL
Version 2.14 – June 10th 2010 - Page 15 of 15
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning
"Industry Canada regulatory information Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. ""The user is
cautioned that this device should be used only as specified within this manual to meet RF
exposure requirements. Use of this device in a manner inconsistent with this manual could
lead to excessive RF exposure conditions."
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body. This
device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users.
Information To Be Supplied to the End User by the OEM or Integrator
The following regulatory and safety notices must be published in documentation supplied to
the end user of the product or system incorporating an adapter in compliance with local
regulations. Host system
must be labeled with "Contains FCCID:PPQ-CR8702K“, FCC ID displayed on label.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Jo
Create Date                     : 2011:03:08 10:16:49+08:00
Modify Date                     : 2011:03:09 13:36:38+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : Jo
Title                           : Microsoft Word - dat_CR860_CR870_2_14_datasheet.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2011:03:09 13:36:38+08:00
Producer                        : Acrobat Distiller 9.4.2 (Windows)
Document ID                     : uuid:bde8d982-f715-44b5-85a6-c35ee067dcda
Instance ID                     : uuid:e863ecda-bc94-4c2c-84ca-a1c1fab7e8e0
Page Count                      : 16

EXIF Metadata provided by EXIF.tools