Labway B151G3 DVD PLAYBACK CARD FOR PERSONAL COMPUTER User Manual
Labway Corporation DVD PLAYBACK CARD FOR PERSONAL COMPUTER
Labway >
USER MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 21605 |
| Application ID | FtcR03P2hpxFcfMVHhN16w== |
| Document Description | USER MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 25.87kB (323343 bits) |
| Date Submitted | 1999-01-29 00:00:00 |
| Date Available | 1999-03-15 00:00:00 |
| Creation Date | 2001-07-06 10:51:57 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-07-06 10:51:58 |
| Document Title | USER MANUAL |
USER MANUAL PC DVD Playback Card October 1998 A-120-0034 Version 1.0 W9922PF PC DVD Playback Card The information in this document is subject to change without notice FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Note: The user may find the following booklet prepared by the Federal Communications Commission helpful: " How to Identify and Resolve Radio-TV Interference Problems. " This booklet is available from the U.S. Government Printing Office, Washington, DC 20402 Stock No. 004-000-00345-4. All brands and trademarks are registered by their respective companies. Page - 1 W9922PF PC DVD Playback Card TABLE OF CONTENTS 1. DESCRIPTION .................................................................................................3 1.1. FEATURES .................................................................................................................................... 3 1.2. SYSTEM REQUIREMENTS .............................................................................................................. 3 1.3. CARD FIGURE .............................................................................................................................. 4 1.4. CONNECTORS ............................................................................................................................... 4 1.4.1. External Connectors: .............................................................................................................................4 2. HARDWARE INSTALLATION .....................................................................5 2.1. PACKAGE CONTENTS ................................................................................................................... 5 2.2. HANDLING THE DVD DECODER CARD ......................................................................................... 5 2.3. INSTALLING THE PC DVD PLAYBACK CARD................................................................................ 5 2.3.1. Video Connections .................................................................................................................................6 2.3.2. TV Connections......................................................................................................................................7 3. SOFTWARE INSTALLATION ......................................................................9 3.1. SOFTWARE CONTENTS ................................................................................................................. 9 3.2. DEVICE DRIVER AND APPLICATION INSTALLATION UNDER WINDOWS® 95 .................................. 9 3.2.1. Device Driver Installation Under Windows® 95 ...................................................................................9 3.2.2. Application Software Installation Under Windows® 95 ......................................................................12 3.3. REGION CODE CONFIGURATION ................................................................................................. 16 4. WINMPEG-2 APPLICATION SOFTWARE ........................................................18 4.1. USER INTERFACE EXPLANATION-USER PANEL ............................................................................ 18 5. ABOUT PC DVD...............................................................................................21 5.1. DVD LICENSE STATEMENTS ...................................................................................................... 21 5.1.1. Notice for Dolby Laboratories .............................................................................................................21 5.1.2. Notice for Macrovision ........................................................................................................................21 Page - 2 W9922PF 1. PC DVD Playback Card DESCRIPTION This is a new PC DVD Playback Card that provides at low cost, high integration system for playback of MPEG-2, Dolby video and audio bitstreams in Windows-based personal computers. Our PC DVD Playback card not only meets the new demands of advanced PC audio and video applications but also enables the integration of a complete multimedia subsystem. It has software support for games, DVD and Video-CD movies in Microsoft® Windows® operating systems. 1.1. Features • Decodes MPEG-2 at MP@ ML and MPEG-1 video streams • Full support for multiple CD formats: Karaoke CD, Video CD, Super Video CD, CVD, CD-1 and DVD titles • Built-in PCI and VMI/VIP bus interfaces • Directs interface to 1Mx16-bit SDRAM • Supports Video Scaling • Automatic frame rate conversion • Provides RGB and YCbCr video output formats • Decodes DVD compliant sub-picture and highlights • Supports 16:9 and 4:3 aspect ratio by pan & scan and letter box conversion • Supports audio/video synchronization • Fully 3.3V operation • Standard 160-pin PQFP • • • • • • • 1.2. System Requirements 2 Mbytes of free hard disk space, and 16 Mbytes of RAM Pentium-based PC (or compatible), 166 MHz or higher PCI 2.1 compliant expansion slot VGA card DVD-ROM drive Sound Blaster compatible sound card Microsoftâ Windowsâ 95 or later version Page - 3 W9922PF 1.3. PC DVD Playback Card Card Figure P1 DAC & MUX Winbond SDRAM W9951TF VGA Monitor Connector (to VGA Monitor) P2 VGA LOOP Back Con. (to VGA Card) TV Encoder J1 MPEG-II Winbond W9922PF Composite VIDEO Output Con. TV-SET J2 S-VIDEO Output Con. lllllllllllllllllllllllllllllllll lllllll Winbond Chipset W9922PF Figure - 1 1.4. Connectors This DVD Playback Card includes one Output Connector for S-Video, one Output connector for Composite Video, one VGA Loop Back Connector, and one Connector for the VGA Monitor. 1.4.1. External Connectors: J1: ................ RCA Jack for COMPOSITE VIDEO OUTPUT. (to TV set) J2: ................ 4-pin Connector for S-VIDEO OUTPUT. (to TV set) P1: ................ 15-pin D-shape Connector for VGA MONITOR. P2: ................ 9-pin female MINI-DIN Connector for VGA LOOP BACK Cable. (to VGA card) Page - 4 W9922PF 2. PC DVD Playback Card HARDWARE INSTALLATION 2.1. Package Contents Before you start to install your PC DVD Playback Card you should check that the package is complete. It should contain the following items: • • 1 LAB DVD Decoder CARD 1 Installation CD-title CABLE: • 1 VGA Loop Back Cable 2.2. Handling the DVD Decoder Card WARNING: Static electricity can damage your equipment. Do not take the card out of its static protective bag until you are ready to work with it. Follow these precautions when handling the board: • Before you open the static protective bag, touch it to a metal expansion slot cover on the back of your computer. This drains static electricity from the package and from your body. • Do not touch any exposed printed circuitry after opening the package. • Keep other people from touching the board. They might have a static-electricity build-up. • Limit your movement. Movement causes a build-up of static electricity. 2.3. Installing the PC DVD Playback Card Follow the steps below to install the PC DVD Playback Card into your computer. 1.) Turn off the power to the computer and to the VGA monitor. Unplug (disconnect) the power cord from the computer. 2.) Disconnect the VGA monitor cable from your PC. 3.) Remove the cover from the computer. (Refer to your PC user’s manual for specific instructions.) 4.) Locate an available PCI expansion slot. 5.) Remove the slot cover screw and slot cover, if applicable. 6.) Open the protective sleeve containing the PC DVD Playback Card, grasp the circuit board by the edge of its mounting bracket, and remove it from the protective sleeve. Page - 5 W9922PF PC DVD Playback Card 7.) Insert the card into the PCI/AGP expansion slot. Press down gently on the top edges of the board to ensure that all connecting points are seated securely. Anchor the board’s mounting bracket using the screw removed earlier. 8.) Replace the cover of your PC and reconnect the power cord. NOTE: If you install a DVD-ROM drive at the same time as the PC DVD Playback Card, remember to attach the CD-Audio cable from the DVD-ROM drive to your sound card. Otherwise, you will not be able to play CD-Audio titles with the DVD-ROM drive. This will not affect the audio of DVD-Video or DVD-ROM titles. 2.3.1. Video Connections VGA MONITOR Connector P1 VGA LOOP BACK Connector P2 Figure - 2 Installation: Step 1. Plug the VGA LOOP BACK Cable into the 9-pin female MINI-DIN connector P2 on the PC DVD Playback Card and the other side into the 15-pin D-shape female VGA Output connector of your VGA Card. Step 2. Plug the VGA Monitor Cable into the 15-pin D-shape female VGA Output connector P1 on the PC DVD Playback Card. Page - 6 W9922PF PC DVD Playback Card 2.3.2. TV Connections There are two methods of connecting your PC DVD Playback Card to a television set: S-Video by using a standard S-Video cable, or Composite Video by using a standard Composite Video cable. A) S-VIDEO Output Connector J2 The S-Video Output connector on the PC DVD Playback Card is a 4-pin female S-Video connector, which can be connected directly to a TV using a standard S-Video cable. The S-Video Out connector provides better picture quality. Figure - 3 Installation: Step 1. Plug the S-VIDEO Output Cable into the 4-pin female S-VIDEO Output port J2 on the PC DVD Playback Card and the other side into the S-VIDEO Input port of your TV set. Please refer to Figure 3 for the location of this external connector. NOTE: Due to the copyright protection circuit in use by this product, please do not connect any recording device, such as a VCR, to the S-Video Out connector J2 of the PC DVD Playback Card. For best playback, make sure the DVD title is played directly from the PC DVD Playback Card onto a TV, not through a VCR. Page - 7 W9922PF B) PC DVD Playback Card Composite VIDEO Output Connector J1 If your television set does not support an S-Video input port, you may connect it to the PC DVD Playback Card by using a Composite Video cable. Composite Video is more common and works with most televisions. Figure - 4 Installation: Step 1. Plug the COMPOSITE VIDEO Cable into the RCA Jack J1 on the PC DVD Playback Card and the other side into the Composite VIDEO Input port of your TV set. Please refer to Figure 4 for the location of this external connector. NOTE: Due to the copyright protection circuit in use by this product, please do not connect any recording device, such as a VCR, to the Composite Video Out connectorJ1 of the PC DVD Playback Card. For best playback, make sure the DVD title is played directly from the PC DVD Playback Card onto a TV, not through a VCR. Page - 8 W9922PF 3. PC DVD Playback Card SOFTWARE INSTALLATION 3.1. Software Contents There is one CD title which comes with this package, labeled: PC DVD Player DRIVER & APPLICATION” This CD title includes the device drivers and application software for the Microsoft® Windows® 95 operating system. 3.2. Device Driver and Application Installation Under Windows® 95 3.2.1. Device Driver Installation Under Windows® 95 If you want to install the device driver for your PC DVD Playback Card onto your PC system, please do the following: 1.) First start up your Microsoftâ Windowsâ 95 operating system. 2.) Insert your CD-title, labeled PC DVD Player DRIVER & APPLICATION”, into your CD-ROM driver D or E. 3.) The first “Update Device Driver Wizard” window will appear. Click now on the “Next>” push button. Page - 9 W9922PF PC DVD Playback Card 4.) The next “Update Device Driver Wizard” window will inform you that Windows was unable to locate a driver for your device. Please click on the other Locations...” push button. 5.) Please type the path of the device driver files into the command line of the “Select Other Location” dialog box. Assuming your CD-ROM drive is D, type the command D:\DRV and click on the “OK” push button. Page - 10 W9922PF 6.) PC DVD Playback Card This “Update Device Driver Wizard” dialog box will show you the updated driver for your “Winbond DVD Decoder” device. If you want to accept this driver click now on the “Finish” push button. Page - 11 W9922PF PC DVD Playback Card 3.2.2. Application Software Installation Under Windows® 95 If you want to install the application software for your PC DVD Playback Card onto your PC system, please do the following: 1.) First start up your Microsoftâ Windowsâ 95 operating system. 2.) Then click on the START button and select the RUN item. 3.) Insert your CD-title, labeled PC DVD Player DRIVER & APPLICATION”, into your CD-ROM drive D or E. Assuming your CD-ROM drive is D, type D:\DRV\SETUP.EXE in the command line of the Run dialog box. Click on the OK push button. 4.) The “WinMPEG-II Player Setup...” window will appear, showing you the “Select Regional Code” dialog box. Please select now the correct regional code and click on the “Next>” push button. Page - 12 W9922PF PC DVD Playback Card 5.) The WinMPEG-II Installation” dialog box will appear as shown below. Please read the text carefully and click on the “Next>” push button. 6.) The next “WinMPEG-2 Installation” dialog box appears. You are asked to select the destination directory. You may accept the default directory C:\Program Files\WinMPEG2 and click on the “Next>” push button or you can choose a directory you prefer by clicking on the “Browse” push button. Page - 13 W9922PF PC DVD Playback Card 7.) When the next dialog box appears you just need to click on the “OK” push button to continue. 8.) The next “WinMPEG-2 Installation” window will show you the message “Ready to Install!”. Please click on the “Next>” push button to continue the installation of the application program. Page - 14 W9922PF 9.) PC DVD Playback Card A “Notification” dialog box will appear, asking you if you want to install “Remote Control”. Please select the appropriate COM port and click on the “Yes” or “No” push button to proceed. 10.) The “ReadMe” window will appear. Please click on the “Yes” or “No” push button to continue. 11.) The WinMPEG-II Installation” window will appear. Congratulations! You have successfully installed the application software. Please click on the “Finish” push button. Page - 15 W9922PF PC DVD Playback Card 12.) Click now on “OK” to restart your system so the changes can take effect immediately. 3.3. Region Code Configuration If you want to configure the region code for your PC DVD Playback card, please follow the steps as described below: 1.) 2.) 3.) 4.) Please start up your Microsoftâ Windowsâ 95 operating system. Click on the Start button and select the RUN item. Insert your CD-title into your CD-ROM drive D or E. Assuming your CD-ROM drive is D, type D:\DRV \SETUP.EXE in the command line of the Run dialog box. Click on the OK button. The first window will appear. If you want now to change the regional code click on the “Yes” button, otherwise confirm your current regional code with the “No” button. Page - 16 W9922PF PC DVD Playback Card 5.) The following window will appear: 6.) Please select the correct region code which matches the region code of the movies you wish to play and click on the “Next>” push button. Region Code List Region 1 : Region 2 : Region 3 : Region 4 : Region 5 : Region 6 : United States and Canada Europe and Japan Far East (except China and Japan) South America Africa and Middle East China Page - 17 W9922PF 4. PC DVD Playback Card WinMPEG-2 Application Software 4.1. User interface explanation-User Panel Power ON/OFF Open file Minimize On-line help Open disk to play Random access play Numeric buttons Page - 18 W9922PF PC DVD Playback Card ............ Direction button ..........Play back control for VCD 2.0 ............ Direction button ..........Config button ............ Direction button ..........Repeat button ............ Direction button ..........Menu select ....... Enter button ..........Lower audio volume ........... Multi subpicture ........... Multi audio ........... Multi angle ........... Output select (VGA/NTSC/PAL) ........... Full screen Page - 19 W9922PF PC DVD Playback Card ............. Play previous segment ............. Scan backward play ............. Stop button ............. Fast play ............. Play button ............. Slow play ............. Pause button ............. Play step by step ............. Play next segment ............. Scan forward play ......... Power ON/OFF ............. Play previous segment ......... Minimize ............ Play next segment ......... Open disk to play ............ Fast play ......... Open file ............ Slow play .......... Stop button ........ Enter button .......... Play button ............... Menu select .......... Pause button Page - 20 W9922PF 5. PC DVD Playback Card About PC DVD 5.1. DVD License Statements This product is manufactured under licenses from Dolby Laboratories, CSS, and Macrovision. 5.1.1. Notice for Dolby Laboratories "Dolby", Pro logic" and the double- D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. (c)1992-1997 Dolby Laboratories, Inc. All rights reserved. 5.1.2. Notice for Macrovision This product incorporates copyright protection technology that is protected by method claim of certain U.S. patents and other intellectual property rights owner by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. A-120-0034 Version 1.0 Page - 21
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:07:06 10:51:57 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:07:06 10:51:58+01:00 Page Count : 22EXIF Metadata provided by EXIF.tools