Laird Technologies WB45NBT 45 Series WB module with Bluetooth User Manual MSD40NBT Hardware Integration Guide v 02

Laird Technologies 45 Series WB module with Bluetooth MSD40NBT Hardware Integration Guide v 02

Contents

Users Manual

Hardware Integration Guide
Laird WB45NBT
Version 0.6
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
Laird WB45NBT
Hardware Integration Guide
www.lairdtech.com/wireless
REVISION HISTORY
Version Revision Date Change Description Approval
0.1 10/29/12 Preliminary Version
0.2 11/19/12 Corrected module thickness to 3.8 mm.
Added the CAN bus to the Pin Definitions and Specs
table.
Added product images.
New mechanical drawing.
0.3 03/25/12 Removed documentation of 802.11n HT40 support.
Added Current Consumption numbers (Standby
numbers remain TBDs)
Updated Rx Sensitivity numbers.
Changed Summit/SDC references to Laird
0.4 05/08/2013 Added Antenna Connector diagram.
Updated mechanical drawing.
Removed references to HT40 data rate support.
0.5
7/5/2013
Updated BT maximum transmit power.
0.6 09 August 2013 Updated regulatory information including certified
antennas, FCC, IC, and CE documentation
requirements.
Updated mechanical drawings
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
2 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
CONTENTS
Revision History .............................................................................................................................. 2
Contents ........................................................................................................................................ 3
Scope ............................................................................................................................................. 4
Operational Description .............................................................................................................. 4
Block Diagram ............................................................................................................................... 5
Specifications ................................................................................................................................ 6
Absolute Maximum Ratings............................................................................................... 11
Recommended Operating Conditions and DC power Electrical Characteristics ... 12
Power on Sequence .............................................................................................................. 13
DC Electrical Characteristics (3.3 V signal level) ........................................................... 13
DC Electrical Characteristics (1.8 V signal level) ........................................................... 15
Pin Definitions .............................................................................................................................. 16
Mechanical Specification ......................................................................................................... 20
Regulatory ................................................................................................................................... 22
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
3 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
SCOPE
This document describes key hardware aspects of the Laird WB45NBT wireless bridge module.
This document is intended to assist device manufacturers and related parties with the integration
of this module into their host devices. Data in this document are drawn from a number of
sources including data sheets for the QUALCOMM Atheros AR6003, CSR CSR8510, and Atmel
AT91SAM9G25.
Because the LAIRD WB45NBT is currently in development stage, this document is preliminary and
the information in this document is subject to change. Please contact Summit or visit the Summit
website at www.summitdata.com to obtain the most recent version of this document.
OPERATIONAL DESCRIPTION
This device is a LAIRD WB45NBT wireless bridge module, a
wireless communications subsystem that may be integrated
into a variety of host devices via a number of available
electronic and logical interfaces. The LAIRD WB45NBT provides
complete enterprise-class Wi-Fi connectivity with an integrated
TCP/IP stack, full support for IEEE 802.11a/b/g/n and Bluetooth
4.0 dual-mode air standards with a fully integrated security
supplicant providing 802.11i/WPA2 Enterprise authentication,
data encryption, and BT protocol stacks.
The WB45NBT has a wide variety of interfaces including Fast
Ethernet, serial UART, Hi-Speed USB, SPI, and I2C. The wireless
bridge may be configured, monitored, and managed via a
Command Line Interface (CLI) over an available dedicated
console port, via a web interface over a wireless or Ethernet
interface, or via a remote SDK interface over wireless or
Ethernet.
The WB45NBT incorporates a Wi-Fi SiP module using Qualcomm
Atheros AR6003 which supports IEEE 802.11a/b/g/n. The CSR
(CSR8510) Bluetooth chip supports Bluetooth standard 4.0 which
includes the Bluetooth Low Energy (BLE) and legacy modes. The
product features an ARM9 processor running at 400 MHz, 64 MB
of Lower Power DDR (LPDDR) memory, and 128 MB of NAND
flash storage running at 1.8 V to minimize power consumption.
Several GPIO lines are available for data acquisition and similar
applications. The platform runs an embedded Linux operating
system based on the 3.x kernel. A Software Developer’s Kit (SDK) with Application Programming
Interfaces (API) and software tools are available for the development of custom software
applications on the device.
The WB45NBT measures 40 mm long by 40 mm wide by 3.8 mm thick. The wireless bridge
physically interfaces to the host device via an 80 pin board to board (B2B) connector (Molex
SlimStack™ 54722 Series 80 Pin Connector P/N 54722-0804), which mates to a 1.5 mm stacking
height mating part from Molex 55560 Series P/N 55560-0804. The WB45NBT may be secured to the
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
4 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
host device via available grounded mounting holes. The WB45NBT operates at temperatures
between -20° and + 70° degrees Celsius.
Contingent on compliance results, WB45NBT is a fully integrated module. It has its own RF
shielding and does not require shielding provided by the host device into which it is installed in
order to maintain compliance with applicable regulatory standards. As such, the device may be
tested in a standalone configuration via a breakout board (SDC-BB45NBT).
The WB45NBT provides three U.FL type antenna connectors; the Main antenna (for Wi-Fi) and the
Auxiliary (for Bluetooth) work separately to get the best coexistence performance. A third
antenna connector multiplexes both the Wi-Fi and the Bluetooth signals into a single RF port
through the use of a T/R switch however, this mode of operation is currently not supported.
Supported host device antenna types include dipole and monopole antennas.
Regulatory operational requirements are included in this document and may be incorporated
into the operating manual of any device into which the WB45NBT is installed. The WB45NBT is
designed for installation into mobile devices which typically operate at distances greater than
20 cm from the human body and portable devices which typically operate at distances less
than 20 cm from the human body. See “Documentation Requirements” for more information.
BLOCK DIAGRAM
Note: Transmitter frequencies for Wi-Fi are 2412-2462 MHz and 5180-5805 MHz. Transmitter
frequencies for Bluetooth are 2402-2480 MHz.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
5 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Note: Bluetooth functions on the AUX port and Wi-Fi operates at the Main antenna only.
The WB45NBT does not currently support Wi-Fi and BT sharing a single antenna
implementation.
SPECIFICATIONS
Description
Pitch: 0.5 mm
Stacking height: 1.50 mm
Molex 54722 Series 80 Pin Connector P/N 54722-0804
Mating part:
Molex 55560 Series 80 Pin Connector P/N 55560-0804
Note: See Mounting for mating connector options.
Ethernet Interface
(3.3 V signal level) 10/100 Mbps RMII (Reduced Media Independent Interface)
Asynchronous Serial
Port
Interfaces
(1.8 V signal level)
Four-wire UART with hardware handshaking (up to 921,600 baud)
Two-wire UART (console) for debug purpose
SPI Interface
(1.8 V signal level) Five Wire, Master and Slave modes supported with 2 chip select
USB Interfaces Configurable USB Host port/Device port to support USB full speed and
high speed data rates
Two Wire Interface
(1.8V signal level) Two-wire I2C (Inter-IC)
CAN Interface
(1.8V signal level) Controller area network (multiplexed with Two-wire UART)
Debug Interface Two-wire UART (console) for debug purpose
Digital GPIO
(1.8 V signal level) 4 digital General Purpose I/O (GPIO)
Analog GPIO
(3.3 V signal level) 4 analog General Purpose I/O (GPIO)
PCM interface 13-bit or 16-bit linear, 8-bit μ-law or A-law companded sample formats
Antenna Interface 2 Hirose U.FL connectors for Wi-Fi (Main) and BT (Aux) separately, 50
ohm
Note: Wi-Fi and BT sharing a single antenna is NOT currently supported.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
6 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Wi-Fi Interface Qualcomm Atheros AR6003 1X1 802.11 a/b/g/n on 20 MHz bandwidth
Bluetooth Interface CSR CSR8510 Bluetooth 4.0 dual-mode (EDR+BLE)
Processor Chip Set Atmel 400 MHz ARM 9, P/N AT91SAM9G25-CU
Operating System Embedded Linux, 3.x kernel
Memory 64 MB LPDDR
Storage 128 MB SLC NAND flash
Input Voltage
Requirements 3.3 VDC +/-5% (Backup) 3.3 VDC ±5% (system) 1.8 VDC +/-5% (Memory
and I/O interface)
Note: Voltage ripple must be less than 30 mV.
Current Consumption
Note: These current
consumption
measurements
were taken
using Linux
kernel version
2.6.38.
Note: Standby refers to
the radio
operating in
PM1 power
saving mode.
Mode 1.8 V 3.3 V
Avg.
Current Max.
Current Avg.
Current Max.
Current
802.11a
Transmit 80 120 297 484
Receive 97 - 47 -
Standby TBD TBD TBD TBD
802.11b Transmit 75 108 243 368
Receive 97 - 47 -
Standby TBD TBD TBD TBD
802.11g Transmit 80 115 210 361
Receive 97 - 47 -
Standby TBD TBD TBD TBD
802.11n (2.4 GHz) Transmit 81 120 194 342
Receive 97 - 47 -
Standby TBD TBD TBD TBD
802.11n (5 GHz) Transmit TBD 120 293 448
Receive 97 - 47 -
Standby TBD TBD TBD TBD
Sleep N/A TBD TBD TBD TBD
Operating
Temperature -20° to +70°C (-4°F to 158°F)
Operating Humidity 10 to 90% (non-condensing)
Storage Temperature -30° to 85°C (-22° to 185°F)
Storage Humidity 10 to 90% (non-condensing)
Maximum Electrostatic
Discharge Maximum Contact Discharge (CD): 4 kV
Maximum Air Discharge (AD): 8 kV
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
7 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Length/Width/Thicknes
s 40 mm (1.57 in.) x 40 mm (1.57 in.) x 3.8 mm (0.15 in.)
Note: Length, width, and thickness measurements include the metal
shielding.
Weight 6.8 g (0.24 oz.)
Mounting Connector and through holes.
Refer to “Mechanical Specifications” for additional information.
Recommended:
Connector:
Molex SlimStack™ P/N 55560-0807
(pitch: 0.50 mm; stack height: 1.500 mm)
Mating part: Molex 55560 Series 80 Pin Connector P/N 55560-0804
Stand-off: EMI STOP F40M20-151126D4BM http://www.emistop.com
Wi-Fi Media Direct Sequence-Spread Spectrum (DSSS)
Complementary Code Keying (CCK)
Orthogonal Frequency Divisional Multiplexing (OFDM)
Wi-Fi Media Access
Protocol Carrier sense multiple access with collision avoidance (CSMA/CA)
Network Architecture Infrastructure and ad hoc
Wi-Fi Standards IEEE 802.11a, 802.11b, 802.11d, 802.11e, 802.11g, 802.11h, 802.11i,
802.11n
Supported
802.11a
(OFDM): 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11b (DSSS, CCK): 1, 2, 5.5, 11 Mbps
802.11g (OFDM): 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n (OFDM,HT20,MCS 0-7): 6.5,13,19.5, 26, 39,52, 58.5, 72.2 Mbps
7.2,14.4, 21.7, 28.9,43.3, 57.8, 65 Mbps
Modulation BPSK @ 1, 6, 6.5, 7.2 and 9 Mbps
QPSK @ 2, 12, 13, 14.4,18, 19.5 and 21.7 Mbps
CCK @ 5.5 and 11 Mbps
16-QAM @ 24, 26, 28.9, 36, 39 and 43.3 Mbps
64-QAM @ 48, 52, 54, 57.8, 58.5, 65, and 72.2 Mbps
802.11n Spatial
Streams 1X1 SISO (Single Input, Single Output)
Regulatory Domain
Support FCC (Americas, Parts of Asia, and Middle East)
ETSI (Europe, Middle East, Africa, and Parts of Asia)
MIC (Japan) (formerly TELEC)
KC (Korea) (formerly KCC)
2.4 GHz Frequency
Bands ETSI: 2.4 GHz to 2.483 GHz
FCC: 2.4 GHz to 2.483 GHz
MIC: 2.4 GHz to 2.495 GHz
KC: 2.4 GHz to 2.483 GHz
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
8 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Channels
ETSI:
13 (3 non-overlapping)
FCC: 11 (3 non-overlapping)
MIC:
14 (4 non-overlapping)
KC: 13 (3 non-overlapping)
5 GHz Frequency
Bands ETSI: 5.15 GHz to 5.35 GHz
5.47 GHz to 5.725 GHz
FCC: 5.15 GHz to 5.35 GHz
5.725 GHz to 5.825 GHz
MIC: 5.15 GHz to 5.35 GHz
5.47 GHz to 5.725 GHz (W56)
KC: 5.15 GHz to 5.25 GHz
5.725 GHz to 5.825 GHz
Channels
ETSI:
19 non-overlapping
FCC: 23 non-overlapping
MIC:
4 non-overlapping
KC: 8 non-overlapping
Maximum Transmit
Power
Note: Maximum
transmits power
varies
according to
individual
country
regulations. All
values nominal,
+/-2 dBm.
Note: Summit 45 series
radios support a
single spatial
stream and 20
MHz channel
bandwidth at
2.4GHz.
802.11a
6 Mbps
15 dBm ( 31.623 mW)
54 Mbps
13 dBm ( 19.953 mW)
802.11b
1 Mbps
16 dBm ( 39.81 mW)
11 Mbps
16 dBm ( 39.81mW)
802.11g
6 Mbps
16 dBm ( 39.81 mW)
54 Mbps
14 dBm ( 25.12 mW)
802.11n (2.4 GHz)
6.5 Mbps (MCS0)
16 dBm (39.81 mW)
65 Mbps (MCS7)
12 dBm (15.85 mW)
802.11n (5 GHz HT20)
6.5 Mbps (MCS0)
15 dBm ( 31.62mW)
65 Mbps (MCS7)
12 dBm ( 15.85mW)
Bluetooth
6 dBm (3.98mW) (Class 1)
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
9 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Typical Receiver
Sensitivity
Note: All values
nominal, +/-3
dBm.
802.11a:
6 Mbps
-93 dBm
54 Mbps
-77 dBm (PER <= 10%)
802.11b:
1 Mbps
-93 dBm
11 Mbps
-84 dBm (PER <= 8%)
802.11g:
6 Mbps
-90 dBm
54 Mbps
-73 dBm (PER <= 10%)
802.11n (2.4 GHz)
MCS0 Mbps
-89 dBm
MCS7 Mbps
-71 dBm
802.11n (5 GHz HT20)
MCS0 Mbps
MCS7 Mbps
-93 dBm
-77 dBm
Bluetooth:
1 Mbps
-89 dBm
2 Mbps
-91 dBm
3 Mbps
-85 dBm
Security
Standards
Wireless Equivalent Privacy (WEP)
Wi-Fi Protected Access (WPA)
IEEE 802.11i (WPA2)
Encryption
Wireless Equivalent Privacy (WEP, RC4 Algorithm)
Temporal Key Integrity Protocol (TKIP, RC4 Algorithm)
Advanced Encryption Standard (AES, Rijndael Algorithm)
Encryption Key Provisioning
Static (40-bit and 128-bit lengths)
Pre-Shared (PSK)
Dynamic
802.1X Extensible Authentication Protocol Types
EAP-FAST
EAP-TLS
EAP-TTLS
PEAP-GTC
PEAP-MSCHAPv2
PEAP-TLS
LEAP
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
10 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Compliance
Note: These regulatory
domain
certifications
are pending.
ETSI Regulatory Domain
EN 300 328
EN 300 328 v1.7.1 (BT 2.1)
EN 301 489-1
EN 301 489-17
EN 301 893
EN 60950-1
EN 55022:2006 Class B
EN 55024:1998 +A1:2001, A2:2003
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1:2001, A2:2005
EU 2002/95/EC (RoHS)
FCC Regulatory Domain
FCC 15.247 DTS – 802.11b/g (Wi-Fi): 2.4 GHz & 5.8 GHz
FCC 15.407 UNII – 802.11a (Wi-Fi): 2.4 GHz & 5.4 GHz
FCC 15.247 DSS – BT 2.1
FCC Part 15 Class B
UL 60950
Industry Canada
RSS-210 – 802.11a/b/g/n (Wi-Fi) – 2.4 GHz, 5.8 GHz, 5.2 GHz, and 5.4
GHz
ICES-003, Class B
CSA C22.2, No. 60950
RSS-210 – BT 2.1
MIC (Japan) Regulatory Domain (formerly TELEC)
Article 2 Item 19, Category WW (2.4GHz Channels 1-13)
Article 2 Item 19-2, Category GZ (2.4GHz Channel 14)
Article 2 Item 19-3 Category XW (5150-5250 W52 & 5250-5350 W53)
VCCI Class B
Article 2-1 Item 19-2 (BT 2.1)
Certifications
Note: These
certifications
are pending.
Wi-Fi Alliance
802.11a, 802.11b, 802.11g , 802.11n
WPA Enterprise
WPA2 Enterprise
Cisco Compatible Extensions (Version 4)
Limited Lifetime
All specifications are subject to change without notice
Absolute Maximum Ratings
Parameter
Comments
Conditions
Min.
Typ.
Max.
Unit
Input Voltage 3.3V VCC pin
With respect to ground
-0.3 - 3.8 V
1.8V VCC pin -0.3 - 2.0 V
Any 3.3V IO
pin -0.3 - 3.8 V
Any 1.8V IO -0.3 2.0 V
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
11 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Parameter
Comments
Conditions
Min.
Typ.
Max.
Unit
pin
RF input Maximum RF input from
the antenna port
(reference to 50 ohm) +10 dBm
Note: Voltage operated over the maximum limit may cause permanent damage to the
device. These are stress ratings only; functional operation of the device at these or
any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for
extended periods may affect device reliability.
Recommended Operating Conditions and DC power Electrical Characteristics
Parameter
Comments
Conditions
Min.
Typ.
Max.
Unit
Supply Voltage
3.3 V/3.3 V_BU/”3.3
V_ANA
1.8 V VCC
3.14
1.71
3.3
1.8
3.47
1.89 V
Voltage Ripple
3.3 V/3.3 V_BU
3.3 V_ANA/1.8 V - - 30 mV
Recommend
voltage supply
current rating
3.3 V_BU
3.3 V_ANA
3.3 V
1.8 V
-
10
100
1000
500
mA
DC Output
Current Analog IO pin
3.3 V signal
level - - 8 mA
DC Output
Current Digital IO pin
1.8 V signal
level - - 2 mA
Voltage Rise
Time At power on
3.3 V / 3.3 VBU
/ 1.8 V - - 5 ms
Operating
Current
WLAN
sub-system
Continuous
receive
-
TBD
mA
IEEE PSM
TBD
-
-
Continuous
transmit (3.3 V/
1.8 V)
-
330
/85 400/100
Bluetooth
sub-system
Continuous
receive - TBD mA
Continuous
transmit
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
12 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Parameter
Comments
Conditions
Min.
Typ.
Max.
Unit
CPU
sub-system
Varies with
system load - TBD mA
Operating
Temperature -20 25 +70 °C
Power on Sequence
Notes: Apply the 3.3 V (backup and system) and 1.8 V (memory & interface I/O) at the
same time.
The CPU implements the internal POR (Power-On-Reset) and will guarantee the
power sources reach their target values prior to the release of POR.
Tres=30 us, T1=66 us, T2=352 us (minimum)
Establish the VDDIO/CDDIOP (1.8 V for memory & interface I/O) and VCCBU (3.3 V)
first, then VDDPLL (1.0 V from LDO), and the VDDCORE (1.0 V from DC-DC regulator)
to ensure reliable device operation. This is implemented on the WB45NBT, user simply
apply 3.3 V (backup and system) and 1.8 V (memory & interface I/O) at the same
time.
DC Electrical Characteristics (3.3 V signal level)
I/O Indicates whether the signal is input or output state.
PU/PD Indicates whether Pull-Up, Pull-Down, or nothing is enabled.
ST Indicates if Schmitt Trigger is enabled.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
13 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
TR Tri-state
Parameter Conditions Min. Typ. Max. Unit
AIO[0-3]
IRQ
SHDN
WKUP
ETXEN;ETX[0-1];ERXER;ERX[0-1];EMDC;EMDIO;ECRSDV;EREF_CLK
I/O;PU;ST
I;PU;ST
O;PU
I;ST
Note: PU;ST
VIL Input Low-Level Voltage -0.3 - 0.8 V
VIH Input High-Level Voltage 2.0 3.6 V
VOL Output Low-Level Voltage 0.4 V
VOH Output High-Level Voltage 2.9 V
VT- Schmitt trigger Negative-going threshold
Voltage 0.8 1.1 V
VT+ Schmitt trigger Positive-going threshold Voltage 1.6 2.0 V
VHYS Schmitt trigger Hysteresis 0.5 0.75 V
RPULLUP Pull-up/Pull-down Resistance 40 75 190 KΩ
IO Output Current 8 mA
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
14 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
DC Electrical Characteristics (1.8 V signal level)
I/O Indicates whether the signal is input or output state.
PU/PD Indicates whether Pull-Up, Pull-Down or nothing is enabled.
ST Indicates if Schmitt Trigger is enabled.
TR Tri-state
Parameter Conditions Min. Typ. Max. Unit
GPIO[0-3]
TWCK1;TWD1
WOW
WIFI_GPIO
URTS0;UCTS0;URXD0;UTXD0;URTS3;UCTS3;URXD3;UTXD3
DTXD;DRXD
PCM_CLK;PCM_SYNC;PCM_OUT;PCM_IN
I/O;PU;ST
Note: PU;ST
O
I/O
Notes: PU;ST
PU;ST
PD;TR
VIL Input Low-Level Voltage -0.3 - 0.54 V
VIH Input High-Level Voltage 1.26 2.1 V
VOL Output Low-Level Voltage 0.4 V
VOH Output High-Level Voltage 1.4 V
VT- Schmitt trigger Negative-going threshold
Voltage 0.54 V
VT+ Schmitt trigger Positive-going threshold Voltage 0.54 V
VHYS Schmitt trigger Hysteresis 0.28 0.6 V
RPULLUP Pull-up/Pull-down
Resistance 240 1000 KΩ
IO Output Current 2 mA
Note: We recommend that 1.8 V signal I/O pins should not be used to drive the external
circuit directly due to its weak drive capability. A buffer/driver should be used in such
applications.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
15 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
PIN DEFINITIONS
Table 1: Pin Definitions
#
Pin Name
Section
I/O
Reference
Description
If unused
1 +3.3V_ANA - - +3.3 V for analog I/O
interface 3.3 V must be
supplied
2 +3.3V_BU - - +3.3 V for system back up
3.3 V must be
supplied
3 GND - Ground Ground
Must be
connected to
GND
4 GND - Ground Ground
Must be
connected to
GND
5 AIO-1
*VBUS_EN
Analog
I/O I/O
*O +3.3 V_ANA
Analog I/O
*USB interface in Host
mode; used to control
(High enable) the USB bus
power (5 V).
6 WKUP
I +3.3 V_BU
Wake up the processor
from deep sleep mode.
Low active to wake up the
CPU.
Internal 100k pull-up
7 SHDN
O
+3.3 V_BU Shut down the external
power supply for the
module to save power
consumption.
Low active to shut down
the power supply.
Internal 100K pull-up
8 AIO-0
*VBUS_SENS
Analog
I/O
I/O
*I +3.3 V_ANA
Analog I/O
*When USB interfaces in
Device mode; It is used to
sense the USB bus power (5
V).
Note: A voltage divider is
needed to
implement. Please
reference the
BB45NBT design.
9 AIO-3 Analog
I/O I/O +3.3 V_ANA Analog I/O
10 AIO-2
*OVER_CURRENT
Analog
I/O I/O
*I +3.3 V_ANA Analog I/O
*When USB interfaces in
Host mode; It is used to
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
16 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
#
Pin Name
Section
I/O
Reference
Description
If unused
sense the USB bus power
(5V) running over the
current limit.
Note: A voltage switch is
needed to implement.
Please reference the
BB45NBT design.
11 IRQ Control I +3.3 V External Interrupt Input
12 GND - Ground Ground
Must be
connected to
GND
13 GND - Ground Ground
Must be
connected to
GND
14 EMDC Ethernet O +3.3 V Ethernet Management
Data Clock
15 ETXEN Ethernet O +3.3 V Ethernet Transmit Enable
16 GND - Ground Ground
Must be
connected to
GND
17 ETX0 Ethernet O +3.3 V Ethernet Transmit Data 0
18 ETX1 Ethernet O +3.3 V Ethernet Transmit Data 1
19 ERXER Ethernet I +3.3 V Ethernet Receive Error
20 ERX0 Ethernet I +3.3 V Ethernet Receive Data 0
21 GND - Ground Ground
Must be
connected to
GND
22 ERX1 Ethernet I +3.3 V Ethernet Receive Data 1
23 REF_CLK Ethernet I +3.3 V Ethernet 50MHz Clock Leave open
24 ECRSDV Ethernet I +3.3 V Ethernet Receive Data
Valid
25 GND - Ground Ground
Must be
connected to
GND
26 EMDIO Ethernet I/O +3.3 V Ethernet Management
Data Input/Output
27 TWD1 I/O +1.8 V Twist wire bus Data (I2C
Data line)
28 GND - Ground Ground
Must be
connected to
GND
29 TWCK1 O +1.8 V Twist wire bus Clock (I2C
Clock line)
30 +1.8V - - 1.8 V for Memory
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
17 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
#
Pin Name
Section
I/O
Reference
Description
If unused
(NAND/LPDDR), bus
interface and Wi-Fi/BT bus
configuration.
31 GND - Ground Ground
Must be
connected to
GND
32 GND - Ground Ground
Must be
connected to
GND
33 GPIO-0 GPIO I/O +1.8 V General I/O 0 Leave open
34 GPIO-1 GPIO I/O +1.8 V General I/O 1 Leave open
35 GPIO-2 GPIO I/O +1.8 V General I/O 2 Leave open
36 GPIO-3 GPIO I/O +1.8 V General I/O 3 Leave open
37 GND - Ground Ground
Must be
connected to
GND
38 GND - Ground Ground
Must be
connected to
GND
39 URXD3 UART3 I +1.8 V UART3 Receive Data Leave open
40 URTS3 UART3 O +1.8 V UART3 Ready To Send Leave open
41 UTXD3 UART3 O +1.8 V UART3 Transmit Data Leave open
42 UCTS3 UART3 I +1.8 V UART3 Clear To Send Leave open
43 GND - Ground Ground
Must be
connected to
GND
44 GND - Ground Ground
Must be
connected to
GND
45 URXD0 UART0 I +1.8 V UART0 Receive Data Leave open
46 URTS0 UART0 O +1.8 V UART0 Ready To Send Leave open
47 UTXD0 UART0 O +1.8 V UART0 Transmit Data Leave open
48 UCTS0 UART0 I +1.8 V UART0 Clear To Send Leave open
49 GND - Ground Ground
Must be
connected to
GND
50 GND - Ground Ground
Must be
connected to
GND
51 SPI0_CSn1
SPI0 O +1.8 V SPI0 Chip Select. Active
Low
*Only for SPI in Master
mode.
Leave open
52 SPI0_MISO SPI0 I/O +1.8 V SPI0 Master In Slave Out Leave open
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
18 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
#
Pin Name
Section
I/O
Reference
Description
If unused
53 GND - Ground Ground
Must be
connected to
GND
54 SPI0_MOSI SPI0 I/O +1.8 V SPI0 Master Out Slave In Leave in
55 SPI0_CLK SPI0 I/O +1.8 V SPI0 Serial Clock (Master:O
Slave:I) Leave open
56 SPI0_CSn0 SPI0 I/O +1.8 V SPI0 Chip Select. (Master:O
Slave:I)Active Low
Leave open
57 GND - Ground Ground
Must be
connected to
GND
58 GND - Ground Ground
Must be
connected to
GND
59 DRXD DBGU I +1.8 V Debug UART Receive Data
CANRX0 47K Pull-Up
60 +3.3V - - 3.3V for CPU,Wi-Fi and BT
3.3V must be
supplied
61 DTXD DBGU O +1.8V Debug UART Transmit Data
CANTX0 Leave Open
62 +3.3V - - 3.3V for CPU,Wi-Fi and BT
3.3V must be
supplied
63 GND - Ground Ground
Must be
connected to
GND
64 GND - Ground Ground
Must be
connected to
GND
65 HHSDPA USB
Device I/O USB (Host/Device) D+
66 NRST Control I +1.8V CPU Reset; Low active. Leave open
67 HHSDMA USB
Device I/O USB (Host/Device) D-
68 WOW O +1.8V Wake On Wireless LAN
69 GND - Ground Ground
Must be
connected to
GND
70 Wi-Fi GPIO I/O +1.8V Reserved for Wi-Fi GPIO Leave open
71 GND - Ground Ground
Must be
connected to
GND
72 GND - Ground Ground
Must be
connected to
GND
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
19 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
#
Pin Name
Section
I/O
Reference
Description
If unused
73 PCM_CLK
I
O +1.8V
+1.8V PCM CLK input
when BT acts as Slave
PCM CLK output
when BT acts as Master
Leave open
74 PCM_IN I +1.8V PCM signal input.
75 GND - Ground Ground
Must be
connected to
GND
76 GND - Ground Ground
Must be
connected to
GND
77 PCM_SYNC I/O +1.8V PCM signal sync
78 PCM_OUT O +1.8V PCM signal output
79 GND - Ground Ground
Must be
connected to
GND
80 GND - Ground Ground
Must be
connected to
GND
MECHANICAL SPECIFICATION
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
20 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Mounting
TBD
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
21 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
REGULATORY
Certified Antennas
The WB45NBT will be tested to the regulatory standards defined in the “Certifications” section of
the Specifications table above. Summit plans to conduct these tests with the following antennas:
Model Type Connector Maximum Gain
MAG.LAYERS
EDA-1513-25GR2-B2-CY
Dipole SMA
Jack Reverse
2 dBi
MAG.LAYERS
PCA-4606-2G4C1-A13-CY
PCB Dipole TNOV 2.2 dBi
Laird
NanoBlade-IP04
PCB Dipole IPEX MHF
2.4-2.5 GHz: 2 dBi
5.15-5.35 GHz: 3.9 dBi
5.6 GHz: 4 dBi
Laird
MAF95310 Mini NanoBlade Flex
PCB Dipole IPEX MHF 2.4 GHz: 2.79 dBi
5 GHz: 3.38 dBi
Laird
NanoBlue-IP04
PCB Dipole IPEX MHF 2.5 GHz only: 2 dBi
Ethertronics
WLAN_1000146
Magnetic
Dipole IPEX MHF
2.4-2.5 GHz: 2 dBi
4.9-5.1 GHz: 3.5 dBi
5.15-5.35 GHz: 3.5 dBi
5.7-5.9 GHz: 3.5 dBi
Documentation Requirements
In order to ensure regulatory compliance, when integrating the WB45NBT into a host device, it is
necessary to meet the documentation requirements set forth by the applicable regulatory
agencies. The following sections (FCC, Industry Canada, and European Union) outline the
information that may be included in the user’s guide and external labels for the host devices into
which the WB45NBT is integrated.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
22 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to
reduce the potential for harmful interference to co-channel Mobile Satellite systems.
This device does not permit operations on channels 116-128 (5580 – 5640 MHz) for 11na and
120-128 (5600-5640 MHz) for 11a which overlap the 5600 -5650 MHz band.
IMPORTANT NOTE: FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
The transmitter module may not be co-located with any other transmitter or antenna,
For all products marketed in the United States, the OEM must limit the operation
channels from CH1 to CH11 for 2.4 GHz band by the supplied firmware programming
tool. The OEM shall not supply any tool or information to the end-user regarding
Regulatory Domain change.
As long as the three conditions above are met, further transmitter testing is not required.
However, the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
23 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
IMPORTANT NOTE: In the event that these conditions cannot be met (for example, certain
laptop configurations or co-location with another transmitter), then the
FCC authorization is no longer considered valid and the FCC ID cannot
be used on the final product. In these circumstances, the OEM integrator
is responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna is installed such
that 20 cm is maintained between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains FCC ID: SQG-WB45NBT”.
Manual Information to the End User
The OEM integrator may NOT provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warnings as show in this
Hardware Integration Guide.
User’s Guide Requirements (for Model # WB45NBT)
RF Radiation Hazard Warning
To ensure compliance with FCC and Industry Canada RF exposure requirements, this device
must be installed in a location where the antennas of the device will have a minimum distance
of at least 20 cm from all persons. Using higher gain antennas and types of antennas not
certified for use with this product is not allowed. The device shall not be co-located with another
transmitter.
Installez l'appareil en veillant à conserver une distance d'au moins 20 cm entre les éléments
rayonnants et les personnes. Cet avertissement de sécurité est conforme aux limites d'exposition
définies par la norme CNR-102 at relative aux fréquences radio.
Maximum Antenna Gain – If the integrator configures the device such that the antenna is
detectable from the host product.
"This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
24 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
This radio transmitter (identify the device by certification number, or model number if Category II)
has been approved by Industry Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated
for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 3147A-WB45NBT) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal
et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette
liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
please refer to page 22 for antenna list
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son
produit final pour toutes exigences de conformité supplémentaires requis pour ce module
installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the Canada authorization is no longer considered
valid and the IC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
25 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur),
l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur
le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit
final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product
must be labeled in a visible area with the following: “Contains IC:3147A-WB45NBT”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne
peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne
et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription
suivante: "Contient des IC: 3147A-WB45NBT".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant
à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit
final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
European Union
User’s Guide Requirements
The integrator must include specific information in the user’s guide for the device into which the
WB45NBT is integrated. In addition to the required FCC and IC statements outlined above, the
following R&TTE statements must be added in their entirety and without modification into a
prominent place in the user’s guide for the device into which the WB45NBT is integrated:
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The
following test methods have been applied in order to prove presumption of conformity with
the essential requirements of the R&TTE Directive 1999/5/EC:
EN60950-1:2001 A11:2004
Safety of Information Technology Equipment
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
26 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
EN 300 328 V1.7.1: (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band
and using spread spectrum modulation techniques; Harmonized EN covering essential
requirements under article 3.2 of the R&TTE Directive
EN 301 489-1 V1.6.1: (2005-09)
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common
technical requirements
EN 301 489-17 V1.2.1 (2002-08)
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 17: Specific
conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN
equipment
EN 301 893 V1.5.1 (2008-12)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Broadband Radio
Access Networks (BRAN); Specific conditions for 5 GHz high performance RLAN
equipment
EU 2002/95/EC (RoHS)
Declaration of Compliance – EU Directive 2003/95/EC; Reduction of Hazardous
Substances (RoHS)
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU
member states and EFTA countries, except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to
obtain authorization to use the device for setting up outdoor radio links and/or for supplying
public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas
the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5
MHz. For detailed information the end-user should contact the national spectrum authority in
France.
Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr
[udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
Deutsch
[German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
27 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme
tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English Hereby, [name of manufacturer], declares that this [type of equipment] is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Español
[Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de
equipo] cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est
conforme aux exigences essentielles et aux autres dispositions pertinentes de
la directive 1999/5/CE.
Italiano
[Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di
apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian] Aršo[name of manufacturer / izgatavotājanosaukums] deklarē, ka[type of
equipment / iekārtas tips]atbilstDirektīvas 1999/5/EK būtiskajāmprasībām un
citiemar to saistītajiemnoteikumiem.
Lietuvių
[Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]
jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus]megfelel a vonatkozó
alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC.
Português
[Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está
conforme com os requisitos essenciais e outras disposições da Directiva
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
28 LAIRD WB45NBT_HIG_V0_6
Laird WB45NBT
Hardware Integration Guide
1999/5/CE.
Slovensko
[Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi
zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak] [Menovýrobcu] týmtovyhlasuje, že [typzariadenia] spĺňazákladnépožiadavky
a všetkypríslušnéustanovenia Smernice 1999/5/ES.
Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment =
laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse
med de väsentliga egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiv 1999/5/EG.
Americas: +1-800-492-2320 Option 3
Europe: +44-1628-858-940
Hong Kong: +852-2268-6567 x026
www.lairdtech.com/wireless
29 LAIRD WB45NBT_HIG_V0_6

Navigation menu