Lambda Technology TWS-G3 True wireless stereo earphones User Manual
Shenzhen Lambda Technology Co.ltd True wireless stereo earphones
User manual
The two earbuds have been connected each other by factory, you
don't need to pair them again. The left earbud is the default master one.
1. Pick up two earbuds from charging station, then tear the stickers on
earbuds first.
2. A few seconds later two earbuds will connect, soon you may hear
voice prompt “left channel / right channel”.
3. Press and hold main button of each earbuds for 2 seconds
simultaneously to power on . A few seconds later two earbuds will
connect each other.After two earbuds connected, the master one
will automatically enter pairing mode, blue and white lights flash
alternately. Then the deputy one is standby mode, blue light flashes
once every 7 seconds. Activate the Bluetooth function on your
device to search for Bluetooth devices. Look for “G3” in device list
display and select. Then you may hear voice prompt “Pairing
successful / Second device connected”.
If two earbuds connection fails, please turn off two earbuds and follow
below operation.
Press and hold main button of each earbud for 4 seconds
simultaneously until blue and white lights flash alternately. A few
seconds later two earbuds will connect. The bluelights will flash 2 times
every 2 seconds. Soon you may hear voice prompt “left channel /
right channel”.Then follow step 3 in PAIRING BOTH EARBUDS.
1. When earbuds are power off, press and hold the main button for
4 seconds until blue and white lights flash quickly, soon you may
hear “pairing”.
2. Activate the Bluetooth function on your device to search for
Bluetooth devices. Look for “G3” in device list display and select.
3. When successful connection is made, blue light will flash once every
7 seconds. Left earbud is now ready for use.
1. When earbuds are power off, press and hold the main button for
4 seconds until blue and white lights flash quickly, soon you may
hear“pairing”.
2. Activate the Bluetooth function on your device to search for
Bluetooth devices. Look for “G3” in device list display and select.
3. When successful connection is made, blue light will ash once every
7 seconds. Right earbud is now ready for use.
Make sure the Bluetooth function is available on your electronic device.
Specific pairing procedures may vary slightly depending on the device.
For detailed information, please refer to your device's User Guide.
· Keep the distance between the device and the earbuds within 3 feet
(for pairing only).
· If no device connection is made within 10 minutes of the earbuds
being switched on, the earbuds will automatically switch off to
save power.
Red
red always on
.
5
5
50
3
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Extreme Temperature 45 degrees max