Landis Gyr Technology FTAR2S1 Communications Adapter User Manual 15 0159 Exhibit Cover

Landis+Gyr Technology, Inc. Communications Adapter 15 0159 Exhibit Cover

Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598Certification ExhibitFCC ID: R7PFTAR2S1IC: 5294A-FTAR1S1FCC Rule Part: 15.247, 15.249IC Radio Standards Specification: RSS-210, RSS-247ACS Project Number: 15-0159Manufacturer: Landis+Gyr Technology, Inc.Model: Communications Adapter
LANDIS+GYR CONFIDENTIAL INFORMATION Communications Adapter Quick Start GuidePublication: 98-1544 Rev AB
Limitation on Warranties and LiabilityInformation in this document is subject to change without notice. This manual or any part of it thereof may not be re-produced in any form unless permitted by contract or by written permission of Landis+Gyr.In no event will Landis+Gyr be liable for any incidental, indirect, special, or consequential damages (including lost prof-its) arising out of or relating to this publication or the information contained in it, even if Landis+Gyr has been advised, knew, or should have known of the possibility of such damages.© 2015 Landis+Gyr, Inc. All Rights ReservedCommunications Adapter Quick Start GuidePublication: 98-1544 Rev ABRevision HistoryModification Date Revision Description Author6/28/2015 ABReleased - Removed references to Field Tool AdapterVicky Costello6/4/2015 AA Released Vicky Costello© 2015 Landis+GyrAll rights reserved.
Quick Start Guide 98-1544 Rev AB 3Communications AdapterQuick Start GuideProduct DescriptionThe Communications Adapter is a lightweight, compact device that is designed to ensure comfortable carrying and holding by the tool user. The adapter tool is capable of decoding one-way and two-way networks in a Gridstream environment. The device also incorporates a bluetooth module that provides communication to the tool device (tablet or laptop) and eliminates the need for serial cable connection. Two-way communication with the adapter provides the capability to transmit and receive data from AMI endpoints. One-way communication operates in a listener mode and provides ability to decode packets from AMR devices including gas and water modules. Figure 1. Communications AdapterBattery Level IndicatorBluetooth ConnectionTwo-way and One-way ActivityPower On and Off ButtonModule ResetComm Adapter’s LAN ID
Communications Adapter Quick Start Guide Landis+Gyr4 98-1544 Rev AB Quick Start GuideNOTE: The LAN ID is a unique identifier for each endpoint. It always displays in hex. Landis+Gyr provides the LAN address. You cannot change the LAN ID of a radio.NOTE: The device was designed to operate at close range in order to minimize interference from unwanted readings while troubleshooting in the field.
Landis+Gyr Communications Adapter Quick Start GuideQuick Start Guide 98-1544 Rev AB 5The Communications Adapter kit includes a battery charger. Figure 2. Communications Adapter KitRequired SoftwareFor specific software and firmware questions, contact your Program/Project Manager directly or your Customer Account Representative.
Communications Adapter Quick Start Guide Landis+Gyr6 98-1544 Rev AB Quick Start GuideGetting StartedTo establish communication with the Communications Adapter, perform the following steps:1. Press and hold the power button on the right-hand side to turn the adapter on.2. Establish bluetooth communication with the tablet/laptop:A. From the Devices and Printers tab, locate or show the bluetooth devices.A list of bluetooth devices is displayed.B. Select Add a Device to choose the device that corresponds to Gridstream followed by the LAN ID printed on the back of the Communications Adapter.C. Enter PIN (0000) to add the device.D. Double-click the device once it is added to the Show Devices tab.E. Click the Hardware tab to obtain the COM port number that is used to set up communication with the software tools (COM port).Once the bluetooth is successfully paired/connected, the Communications Adapter’s Bluetooth Active LED will illuminate.General UsageThe Communications Adapter provides field technicians with full mobility to perform field tool related activities at the site location of the endpoint. Once the tool software is activated, the Communications Adapter is ready to receive information from an electric, gas, or water meter. One-way communication is initiated by the swipe of a magnet to the unit being interrogated. Two-way communication occurs when the Communication Adapter requests information from the unit being interrogated.General SpecificationCommunications Adapter SpecificationsTable 1. Product SpecificationElement DescriptionBattery LifeNormal use is 10 hours.The battery charge level is indicated on the front of the device.To view battery and charging status:- Green indicates the battery is fully charged.- Yellow indicates the battery is half charged.- Red indicates the battery is low and needs charging.RF Output Power 10 milliwatts for close range connectionOne-Way Reception Range 0 to 8 feet from water or gas meterLED 1 Green for One-Way and Two-Way (displayed on front of device)1 Blue for Bluetooth active connection
Landis+Gyr Communications Adapter Quick Start GuideQuick Start Guide 98-1544 Rev AB 7FCC Compliance InformationCompliance for Class B DevicesThis equipment has been tested and found to comply with the limits for a Class B digital device, pur-suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television re-ception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult dealer or an experienced radio/TV technician for help.UWARNING: Changes or modifications to this device not expressly approved by Landis+Gyr could void the user’s authority to operate the equipment.Portable Device RF ExposureThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Industry Canada StatementsUnder Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utili-sateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équiv-alente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Communications Adapter Quick Start Guide Landis+Gyr8 98-1544 Rev AB Quick Start GuideLe présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.FCC & ICFCC ID: R7PFTAR2S1IC: 5294A-FTAR1S1For the Bluetooth module:Contains FCC ID: ED9LMX9838Contains IC: 1520A-LMX9838Model: Communications AdapterFCC Two Part Statement LabelThe FCC label can be located on the back of the Communications Adapter. Figure 3. FCC Two Part Statement Label

Navigation menu