Landis Gyr Technology NG1R1S1 Series 5 Single Board Radio User Manual 98 1822

Landis+Gyr Technology, Inc. Series 5 Single Board Radio 98 1822

Contents

User Manual

LANDIS+GYR CONFIDENTIAL INFORMATIONLandis+GyrNetwork BridgeN2200/N2250Data SheetPublication: 98-1822 Rev AADraft
Limitation on Warranties and LiabilityInformation in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr.In no event will Landis+Gyr be liable for any incidental, indirect, special, or consequential damages (including lost profits) arising out of or relating to this publication or the information contained in it, even if Landis+Gyr has been advised, knew, or should have known of the possibility of such damages.© 2019 Landis+Gyr, Inc. All Rights ReservedCovered by both issued and pending patents.For further patent information see: https://www.landisgyr.com/about/patent-notices/Contact Us:Landis+Gyr technical support:1-888-390-5733solutionsupport.na@landisgyr.comTo provide feedback about this documentation, contact the Technical Documentation team at: ustechnicaldocumentation@landisgyr.com.Landis+Gyr Network Bridge N2200/N2250 Data SheetPublication: 98-1822 Rev AARevision HistoryModification Date Revision Description AuthorAA Draft - Work in Progress Vicky Costello© 2019 Landis+Gyr • All rights reservedDraft
Data Sheet 98-1822 Rev AA 3Network BridgeN2200 (RF Mesh)/N2250 (RF Mesh IP) Data SheetProduct OverviewThe Landis+Gyr Network Bridge provides the basis for a powerful RF wireless mesh network for remote data collection and end-device monitoring and control. The Network Bridge supports full two-way peer-to-peer communication to all devices within the network. The Network Bridge offers advanced functionality, such as individual message prioritization, additional memory for localized intelligence, and it is based on the Linux operating system. The N2200 (RF Mesh)/N2250 (RF Mesh IP) provides interface and control to distribution equipment and critical devices that require low latency. Figure 1 - 1. N2200/N2250 Network BridgeIn addition to the standard RF Mesh and RF Mesh IP radios, the N2200/N2250 has one internal slot that can be fitted with LTE wireless or other future WAN technologies. The N2200/N2250 comes equipped with two serial and two Ethernet ports, and WiFi for configuration. Landis+Gyr's Network Bridge/Network Gateway Platform offers a family of Field Area Network Devices that can be configured and deployed to build a robust communication network infrastructure, enabling communication to edge devices in the field. NOTE: Network Bridge, N2250 (RF Mesh IP), can support the Wi-SUN Field Area Network (FAN) profile through over-the-air (OTA) firmware upgrades.Draft
Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data Sheet Landis+Gyr4 98-1822 Rev AA Data SheetFCC ID LabelsFCC ID Label content is shown in Figure 2 and is required for RF Mesh (2200) and RF Mesh IP (2250). If the X in N22X0, is 0, then this label would be for RF Mesh. If X is 5, then it would be for RF Mesh IP. Figure 2. FCC ID LabelCUID Details Figure 3. CUID DetailsDraft
Landis+Gyr Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data SheetData Sheet 98-1822 Rev AA 5Dimensions Figure 4. Network Bridge Physical Dimensions (mm)Data Ports Pin-Out Figure 5. Data Ports Pin-OutDraft
Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data Sheet Landis+Gyr6 98-1822 Rev AA Data SheetN2200/N2250 SpecificationsProduct SpecificationsTable 1 lists the general product specifications for the N2200 (RF Mesh)/N2250 (RF Mesh IP) Network Bridge Series. Table 1. Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Product Specifications Element DescriptionElectrical (General)Input Voltage Range 12-24 VDC +/- 20% (9.6-28.8 VDC)Current 1.66A-0.83AProcessing UnitCPU Cortex A5Clock Speed 536 MHzRAM Memory 512 MB DDR2 RAMFLASH Memory 2 GB NAND + 4 GB ExternalEthernetETH 0 10/100/1000 EthernetETH 1 10/100 EthernetWIFI YesLTE Cat6 (US Only-ATT and Verizon) YesMechanicalEnclosureBlack Anodized Aluminum, IP41 (ingress protection from dripping condensation and solid material larger than 1mm)Dimensions 55.20mm W X 120.00mm D X 112.10mm H (2.17" W x 4.72" D x 4.41" HWeight 1.10 lbs (0.50 kg)Operating Temperature Range -40°C to 60°C (-40 to 140°F)Storage Temperature Range -40°C to 85°C (-40 to 185°F)Limited LifetimeLife 20 yearsDraft
Landis+Gyr Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data SheetData Sheet 98-1822 Rev AA 7Radio Specifications AmericasTable 2 lists the radio specifications for the N2200 (RF Mesh)/N2250 (RF Mesh IP) Network Bridge Series for Americas. Table 2. Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Radio Specifications Americas Element DescriptionRadio (General)Radio Model Model: NIC AMCommunication Protocol (PHY) IEEE 802.15.4g - SUN FSK PHYRF Frequency RangeNorth America: 902-928 MHzBrazil: 902-907.5, 915-928 MHzChannel SpacingN2250 (RF Mesh IP): 400 KHzN2200 (RF Mesh): 100, 300 KHzRF Data RateN2250 (RF Mesh IP): 50, 150, 200 KbpsN2200 (RF Mesh): 9.6, 19.2, 38.4, 115.2 KbpsBridge Radio Processing UnitCPU Dual-core Cortex M4Clock Speed 120 MHzRAM Memory 304 KbytesFLASH Memory 2 MB + 4MB ExternalROM Memory 8 KbytesReceiver RF Mesh IP:Sensitivity (at 90% packet success rate, conducted, typical) -107 dBm(50 Kbps)-100 dBm(150 Kbps)-98 dBm(200 Kbps)Adjacent Channel Rejection 30 dB TypicalAlternate Channel Rejection 35 dB Typical RF Mesh:Sensitivity (at 90% packet success rate, conducted, typical) -113 dBm(9.6 Kbps)-110 dBm(19.2 Kbps)-107 dBm(38.4 Kbps)-101 dBm (115.2 Kbps)Adjacent Channel Rejection 30 dBAlternate Channel Rejection 35 dBTransmitterDraft
Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data Sheet Landis+Gyr8 98-1822 Rev AA Data SheetOutput Power (at Antenna Connector) 50 mW to 820 mWModulation Type 2FSK, 2GFSKOut-of-band Spurious Emissions < -50 dBcAntennas ApprovedType Vertically-Oriented WhipPeak Gain 5.5dBiWhip, Skywave MMG-11, Rev B 5.5dBi Gain, 902-928 MHz, 50 ohmsType Vertically-Oriented DipolePeak Gain 5.15dBiDipole, Laird FG9023 5.15dBi Gain, 902-928 MHz, 50 ohmsType Vertically-Oriented MonopolePeak Gain 5.15dBiMonopole, Skywave 11-1106E 5.15dBi Gain, 902-928 MHz, 50 ohms Table 2. Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Radio Specifications Americas (Continued)Element DescriptionDraft
Landis+Gyr Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data SheetData Sheet 98-1822 Rev AA 9Radio Specifications IndiaTable 3 lists the radio specifications for the N2200 (RF Mesh)/N2250 (RF Mesh IP) Network Bridge Series for India. Table 3. Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Radio Specifications IndiaElement DescriptionRadio (General)Radio Model Model: NIC INCommunication Protocol (PHY) IEEE 802.15.4-2015 - SUN FSK PHYRF Frequency Range 865-867 MHzChannel SpacingN2250 (RF Mesh IP): 200 KHzN2200 (RF Mesh): 100 KHzRF Data RateN2250 (RF Mesh IP): 50, 150 KbpsN2200 (RF Mesh): 9.6, 19.2, 38.4 KbpsBridge Radio Processing UnitCPU Dual-core Cortex M4Clock Speed 120 MHzRAM Memory 304 KbytesFLASH Memory 2 MB + 4MB ExternalROM Memory 8 KbytesReceiver RF Mesh IP:Sensitivity (at 90% packet success rate, conducted, typical) -107 dBm(50 Kbps)-100 dBm(150 Kbps)Adjacent Channel Rejection 30 dBAlternate Channel Rejection 35 dB RF Mesh:Sensitivity (at 90% packet success rate, conducted, typical) -113 dBM(9.6 Kbps)-110 dBm(19.2 Kbps)-107 dBm(38.4 Kbps)Adjacent Channel Rejection 30 dBAlternate Channel Rejection 35 dBTransmitterOutput Power (at Antenna Connector) 50 mW to 1WModulation Type 2FSK, 2GFSKDraft
Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data Sheet Landis+Gyr10 98-1822 Rev AA Data SheetOut-of-band Spurious Emissions <-50 dBcAntenna RequirementsType Vertically-oriented whipPeak Gain <5.5 dBi Table 3. Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Radio Specifications India(Continued)Element DescriptionDraft
Landis+Gyr Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data SheetData Sheet 98-1822 Rev AA 11Radio Specifications Hong KongTable 4 lists the radio specifications for the N2250 (RF Mesh IP) Network Bridge Series for Hong Kong. Table 4. Network Bridge N2250 (RF Mesh IP) Radio Specifications Hong KongElement DescriptionRadio (General)Radio Model Model: NIC HKCommunication Protocol (PHY) IEEE 802.15.4gRF Frequency Range 920-925 MHzChannel Spacing 400 KHzRF Data Rate 50, 150, 200 KbpsBridge Radio Processing UnitCPU Dual-core Cortex M4Clock Speed 120 MHzRAM Memory 304 KbytesFLASH Memory 2 MB + 4MB ExternalROM Memory 8 KbytesReceiver RF Mesh IP:Sensitivity (at 90% packet success rate, conducted, typical) -107 dBM(50 Kbps)-100 dBm(150 Kbps)-98 dBm(200 Kbps)Adjacent Channel Rejection 30 dBAlternate Channel Rejection 35 dBTransmitterOutput Power (at Antenna Connector) 50 mW to 1WModulation Type 2FSK, 2GFSKOut-of-band Spurious Emissions <-20 dBm ERP Antenna RequirementsType Vertically-oriented whipPeak Gain < 2 dBiDraft
Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data Sheet Landis+Gyr12 98-1822 Rev AA Data SheetRegulatory Compliance Safety and EMC Table 5. Regulatory Standards Compliance: Safety and EMCSpecification DescriptionSafety - Certification pending to: IEC 60950-1:2005Ed.2+A2012;C2012UL 60950-1:2007Ed.2+R:14Oct2014CSA C22.2#60950-1:2007 Ed.2+A1;A2Information Technology Equipment - Safety, as an Over-voltage Class 0 device. Certification Pending.EMC - Certification pending to: CENELEC-EN 55032 2012.01.30 Ed. 1.0 (CISPR 32) EMC of Multimedia Equipment - Emission RequirementsCENELEC-EN 55024 2010/08/24 Ed:2 (CISPR 24) IT Equipment- Immunity characteristicsFCC 47CFR PT 15B, Unintentional RadiatorsIC ICES-003:2016Ed.6Draft
Landis+Gyr Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data SheetData Sheet 98-1822 Rev AA 13FCC ComplianceFCC Class AThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that maycause undesired operation.This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruc-tions, may cause harmful interference to radio communications. However, there is no guar-antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Consult Landis+Gyr or an experienced radio technician for helpUWARNING: Changes or modifications to this device not expressly approved by Landis+Gyr could void the user’s authority to operate the equipment.RF Exposure This equipment complies with FCC and ISED radiation exposure limits. This equipment should be installed and operated with a minimum distance of 30 cm between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites FCC/ISED d'exposition aux radiations définies pour un environnement non contrôlé.Cet équipement doit être installé et utilisé à une distance minimale de 30cm entre le radia-teur et votre corps.Cet émetteur ne doit pas être co-implantés ou exploités en conjonction avec une autre antenne ou émetteur.Draft
Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data Sheet Landis+Gyr14 98-1822 Rev AA Data SheetEIRP LimitThe equipment meets the required FCC specifications with any customer-selectable RF power setting of the radio, using the antennas indicated in this document. FCC testing was conducted using the antennas specified in this document. Antennas with higher gain may result in EIRP levels in excess of the FCC limit.Antennas of a type other than whip, dipole, and monopole are not FCC approved for this device.NOTE: If you increase the power from the factory settings, this can cause communication problems for other radios in the network.Requirement for Hosting Certified RadiosThe following radio modules are approved for use in the Bridge.•NIC•Cell Modems•WiFi Transmitters that are added to the Bridge require testing to be approved.•If the transmitters are added by the customer, the customer is responsible for this testing.•If Landis+Gyr adds these modules, the testing will be performed, and they will be added to the list of approved modules.Industry CanadaThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the trans-mitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.This radio transmitter (5294A-NG1R1S1) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Approved Antenna: Whip, 5.5 dBi gain, 902-928 MHz, 50 ohms.Approved Antenna: Dipole, 5.15 dBi gain, 902-928 MHZ, 50 ohms.Approved Antenna: Monopole 2.15 dBi gain, 902-928 MHz, 50 ohms.Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) Draft
Landis+Gyr Network Bridge N2200 (RF Mesh)/N2250 (RF Mesh IP) Data SheetData Sheet 98-1822 Rev AA 15l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.Le présent émetteur radio (5294A-NG1R1S1) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont stricte-ment interdits pour l'exploitation de l'émetteur.BrazilAnatelEste equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.Regulatory Compliance IndiaWPC GuidelinesThis device complies with WPC guidelines. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.Safety InformationCalifornia Hazard IdentificationUWARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.Draft

Navigation menu