LeapFrog 31500 2.4GHZ SDIO Module User Manual WN7911C LF manual 20140402

LeapFrog Enterprises, Inc. 2.4GHZ SDIO Module WN7911C LF manual 20140402

User manual rev

Download: LeapFrog 31500 2.4GHZ SDIO Module User Manual WN7911C LF manual 20140402
Mirror Download [FCC.gov]LeapFrog 31500 2.4GHZ SDIO Module User Manual WN7911C LF manual 20140402
Document ID2232134
Application IDwf29kpDEGVKzwJ1uuxt5PA==
Document DescriptionUser manual rev
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize16.98kB (212201 bits)
Date Submitted2014-04-02 00:00:00
Date Available2014-09-13 00:00:00
Creation Date2014-04-02 10:24:40
Producing SoftwareGPL Ghostscript 8.15
Document Lastmod2014-04-02 13:09:53
Document TitleMicrosoft Word - WN7911C-LF_manual_20140402.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: ocean_tai

USER MANUAL
USER MANUAL
WN7911C-LF
1x1 Single Band
802.11 b/g/n SDIO Carrier Module
V 0.1
WN7911C-LF
USER MANUAL
Table of Contents
Introduction ........................................................................................................................ 4
1.1
Introduction ........................................................................................................ 4
1.2
Product Features ................................................................................................. 4
Hardware ............................................................................................................................ 5
2.1
General Overview .............................................................................................. 5
2.2
Block Diagram ................................................................................................... 6
2.3
2.4
2.5
Pin Description................................................................................................. 6
PCB Outline & Dimension............................................................................... 10
SDIO Connector Type ...................................................................................... 10
2.5.1
Board to Board Male (for Carrier Board) ................................................ 10
2.5.2
Board to Board Female (for Leapfrog Main Board) ................................ 11
2.5.3
Connector Mating (Mating Height 3 mm) ............................................... 11
Software ........................................................................................................................... 12
3.1
Driver Support.................................................................................................. 12
Specifications ................................................................................................................... 13
4.1
Frequency Band: .............................................................................................. 13
4.2
Transmit Power and Sensitivity: ...................................................................... 13
4.3
4.4
4.5
Modulation ....................................................................................................... 13
Current Consumption: ...................................................................................... 13
Temperature and Humidity............................................................................... 14
4.6 Regulatory and Certification Compliance................................................................ 14
WN7911C-LF
USER MANUAL
Revision History
Edition #
V0.1
Reason for revision
Initial document
Issue date
Written by
July 23, 2013
JC Chiou
WN7911C-LF
USER MANUAL
1 Introduction
1.1
Introduction
WN7911C is an industrial wireless IEEE 802.11n 1x1 2.4GHz single band SDIO module
which enables wireless networking systems to attain data transmission speeds up to 150
megabits-per-second (Mbps). The WN7911C maintains compatibility with legacy IEEE
802.11b.g devices. It supports operation to the IEEE 802.11b and IEEE 802.11g and IEEE
802.11n standards.
1.2
Product Features
Module form factor: 25mm x 18mm
Operate at ISM frequency bands (2.4GHz)
SDIO interface for WiFi
IEEE standards support: IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Security features
 WPA, WPA2, AES encryption/decryption
 TKIP, 802.1x, WAPI encryption/decryption engine
WN7911C-LF
USER MANUAL
2 Hardware
2.1
General Overview
Module Dimension
25mm x 18mm
Module Interface
SDIO v2.0 (50Mhz, 4-bit) host interface
Standard
IEEE 802.11n, 802.11b/g
Chipset
BCM43143 2.4GHz
MAC/PHY/Radio
Description
802.11 b/g/n 2.4GHz 1x1 WiFi carrier
module
Modulation
802.11b:
CCK, DQPSK, DBPSK
802.11g:
802.11 1x1 b/g/n
64 QAM, 16 QAM, QPSK, BPSK
802.11n:
BPSK, QPSK, 16-QAM, 64-QAM
Data Rate
8802.11b:
11, 5.5, 2, 1 Mbps;
802.11g:
54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11n:
MCS 0 to 7 for HT20MHz;
MCS 0 to 7 for HT40MHz
Operating Frequency
Draft 802.11n Radio: 2.4 GHz
802.11g Radio: 2.4 GHz
802.11b Radio: 2.4 GHz
USA – FCC
2412~2462MHz (Ch1~Ch11)
Canada – IC
2412~2462MHz (Ch1~Ch11)
Europe – ETSI
2412~2472MHz (Ch1~Ch13)
Japan – STD-T66/STD-33
2412~2484MHz (Ch1~Ch14)
WN7911C-LF
USER MANUAL
Operating Channel
WiFi 2.4GHz:
11: (Ch. 1-11) – United States
13: (Ch. 1-13) – Europe
14(ch1-14)– Japan
2.400GHz ~ 2.4835 GHz
Antenna Connector
One antenna allowing transmission or
reception on both, simultaneously
Operating System Supported
Linux
Temperatures
Operating Temperature: -10°C to +70 °C
Storage Temperature: -40°C to +80°C
(non-operating):
Humidity
2.2
5-90
Block Diagram
2.3
Pin Description
Pin
Number
Pin
I/O
Type
Type
Terminal Name
Description
BTCX_RF_ACTIVE
Signal I
BTCX_STATUS
Signal I
WN7911C-LF
Indicates that the coexistent BT is active:
internal pull-down.
Indicates the coexistent BT priority status and
RX/TX direction.
USER MANUAL
USB_AVDD12
Power I
USB Phy core 1.2V supply
USB_AVDD25
Power I
USB Phy analog 2.5V supply
USB_AVDD33
Power I
USB Phy analog 3.3V supply
VDD_AFE
Power I
GND
Power I
Ground
USB20_DEV_DPLS
Signal I/O
USB port data plus
USB20_DEV_DMNS
Signal I/O
USB port data minus
10
GND
Power I
Ground
1.2V filtered supply for ADC; 1.2V filtered
supply for AFE AUX
Indicates that the coexistent BT is about to
11
BTCX_FREQ
Signal I
transmit on a restricted channel: internal
pull-down.
12
GPIO_8
Signal I/O
13
BTCX_TXCONF
Signal O
14
UART_TX
Signal O
Serial Input for UART
15
UART_RX
Signal I
Serial Output for UART
16
GND
Power I
Ground
17
VIN_LDO
Power I
Input supply pin for CLDO and LNLDO1
18
VDD_CORE_1.2V
Power O
1.2V output for core LDO, 200mA
19
VDD_RADIO_PLL_O Power O
20
VDD_3.3V
Power O
21
GPIO_0
Signal I/O
General-purpose interface pins.
22
VDD_2.5V
Power O
2.5V LDO2p5 output
23
GND
Power I
Ground
24
VLX
Power O
Core buck regulator: Output to inductor
25
VIN_3V_5V
Power I
Battery supply input for PALDO;
WN7911C-LF
General-purpose interface pins.
Output permission for the coexistent BT to
transmit.
1.2V output for low noise LNLDO1, 150mA
Internal PALDO output or feedback of output
from external PNP
USER MANUAL
Core buck regulator: Battery voltage input
26
GPIO_2
Signal I/O
General-purpose interface pins.
27
GND
Power I
Ground
28
SDIO_CLK
Signal I/O
SDIO clock
29
GPIO_3
Signal I/O
General-purpose interface pins.
30
SDIO_DATA_0
Signal I/O
SDIO data line 0
31
GPIO_1
Signal I/O
General-purpose interface pins.
32
SDIO_DATA_1
Signal I/O
SDIO data line 1
33
SDIO_DATA_2
Signal I/O
SDIO data line 2
34
GPIO_9
Signal I/O
General-purpose interface pins.
Low asserting global chip reset: digital input
pin.
35
RESETn
Signal I
Used by PMU to enable/disable power the
internal regulators.
36
SDIO_CMD
Signal I/O
SDIO command line
37
SDIO_DATA_3
Signal I/O
SDIO data line 3
Digital I/O supply (1.8V to 3.3V)
38
VDDIO
Power I
VDDIO should be supplied externally;
SDIO I/O supply (1.8V to 3.3V)
39
GND
Power I
40
VDD_PLL
Power I
Ground
1.2V supply for PLL;
1.2V crystal oscillator filtered power supply
41
GND
Power I
42
VDD_RADIO_PLL_I
Power I
43
GND
Power I
Ground
44
GND
Power I
Ground
WN7911C-LF
Ground
1.2V supply for radio transmit and receive
sections
USER MANUAL
45
GND
Power I
Ground
46
ANT
Signal I/O
Antenna port
47
GND
Power I
Ground
RF I/O supply (2.6V to 3.3V);
48
VDD_3.3V
Power I
3.3V OTP power supply (no lower than
3.0V);
3.3V for the internal power amplifiers
G1
GND
Power I
Ground pad
G2
GND
Power I
Ground pad
G3
GND
Power I
Ground pad
G4
GND
Power I
Ground pad
G5
GND
Power I
Ground pad
G6
GND
Power I
Ground pad
G7
GND
Power I
Ground pad
G8
GND
Power I
Ground pad
G9
GND
Power I
Ground pad
G10
GND
Power I
Ground pad
G11
GND
Power I
Ground pad
G12
GND
Power I
Ground pad
G13
GND
Power I
Ground pad
WN7911C-LF
USER MANUAL
2.4
PCB Outline & Dimension
2.5
SDIO Connector Type
2.5.1 Board to Board Male (for Carrier Board)
ACC Part Number: NPV014S07R-H
WN7911C-LF
10
USER MANUAL
Unit: mm
2.5.2 Board to Board Female (for Leapfrog Main Board)
ACC Part Number: NPV014P23R-H
Unit: mm
2.5.3 Connector Mating (Mating Height 3 mm)
WN7911C-LF
11
USER MANUAL
Unit: mm
3 Software
3.1
Driver Support
Android
Linux
Windows CE (check for the availability)
WN7911C-LF
12
USER MANUAL
4 Specifications
4.1
4.2
Frequency Band:
802.11n Radio: 2.4 GHz
802.11b/g Radio: 2.4 GHz
Transmit Power and Sensitivity:
TX Output Power: (Typical)
 11b 16 +/- 1 dBm
 11g 10.5+/- 1 dBm
 11n 10 +/- 1 dBm
Rx Sensitivity: (Typical)
 -86 dBm @11 Mbps
 -72 dBm @54 Mbps
 -68 dBm @64-QAM, 20MHz channel spacing
 -61 dBm @64-QAM, 40MHz channel spacing
4.3
4.4
Modulation
DBPSK @1Mbps
DQPSK@2Mbp
CCK@5.5/11Mbps
BPSK@6/9 Mbps
QPSK@12/18Mbps
16-QAM@24Mbps
64-QAM@48/54Mpb and above, up to 300Mbps
Current Consumption:
TX: 263mA x 3.3V Max
RX: 81.58mA x 3.3V Max
Power Saving: 1.25mA x 3.3V
Deep sleep mode: 130uA
WN7911C-LF
13
USER MANUAL
4.5
Temperature and Humidity
Operating Temperature: 0 ~ 40 oC ambient (TBD)
Storage Temperature: -10 ~ 70 oC ambient (TBD)
Humidity: 5 ~ 90% and must be non-condensing (TBD)
4.6
Regulatory and Certification Compliance
TBD
The drawings, specifications and the data contain herein are the exclusive property of Arcadyan
Technology Corp. issued in strict confidence and shall not, without the prior written permission of
Arcadyan Technology Corp., be reproduced, copied or used, in parts or as a whole, for any purpose
whatsoever, except the manufacture of articles for Arcadyan Technology Corp.
Arcadyan makes no warranties with respect to the correctness, accuracy or wholeness of this
specification.
The information in this document is subject to change without notice.
Arcadyan
reserves the right to make revisions to this document and the product described herein without
obligation to notify any person or entity of any such changes.
WARNING
This document is intended for internal use only.
A Non-Disclosure Agreement (NDA)
is required to release this document under any circumstances
WN7911C-LF
14
USER MANUAL
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
WN7911C-LF
15
USER MANUAL
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1)
The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2)
The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must
be labeled in a visible area with the following: “Contains FCC ID: QDX31500”. The grantee's
FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
WN7911C-LF
16
USER MANUAL
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter
tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.
WN7911C-LF
17
USER MANUAL
This device is intended only for OEM integrators under the following conditions: (For module
device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:
(Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur
son produit final pour toutes exigences de conformité supplémentaires requis pour ce module
installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the Canada authorization is no longer considered
valid and the IC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur),
l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé
sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le
produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
WN7911C-LF
18
USER MANUAL
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: “Contains IC: 4810A-31500”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre
l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec
l'inscription suivante: "Contient des IC: 4810A-31500".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du
produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
WN7911C-LF
19

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2014:04:02 10:24:40Z
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2014:04:02 13:09:53+08:00
Metadata Date                   : 2014:04:02 13:09:53+08:00
Format                          : application/pdf
Creator                         : ocean_tai
Title                           : Microsoft Word - WN7911C-LF_manual_20140402.doc
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:5f00d84f-88e7-4d41-bf81-c2923ac4be8e
Instance ID                     : uuid:cd85f0d4-20d4-4ffa-8592-5536a2780e3f
Page Count                      : 19
Author                          : ocean_tai
EXIF Metadata provided by EXIF.tools
FCC ID Filing: QDX31500

Navigation menu