Lee s High Tech Enterprise Co 1211FE2 Industrial Radio Remote Controller User Manual 1120x

Download:
Mirror Download [FCC.gov]
Document ID	1861033
Application ID	U89KzgdzjKWI8C6g8aHrLA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.23kB (315367 bits)
Date Submitted	2012-12-17 00:00:00
Date Available	2012-12-17 00:00:00
Creation Date	2012-11-20 16:04:30
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2012-12-11 13:51:29
Document Title	Microsoft Word - user manual 1120.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Daphne

F21‐E2
Remote controller
User manual
Lee’s Hi‐tech Enterprise. Co., Ltd
1. WARRANTY
1‐1 Warranty
Lee’s Hi‐Tech Enterprises Co., Ltd. guarantees that this product meets its
published specifications at the time of shipment from the factory. Under
proper installation it should work as expected.
1‐2 Warranty period
This equipment is warranted against defects in material and manufacturing
for a period of one year from the date of shipment. During the warranty
period, TELECRANE is responsible for necessary repairs as long as the product
can be proved to be defective.
For warranty service or repair this product must be returned to a service
facility designated by TELECRANE. Buyer will pay shipping charges to
TELECRANE while TELECRANE will pay return shipping charges.
1‐3 Excluded Items
This warranty does not include consumptive parts such as batteries, fuses,
buttons, and relays. Also this warranty does not cover defects caused by
improper installation, improper or insufficient maintenance, unauthorized
modification, and improper operation, ignorance of environmental
specifications, or improper software or interfacing.
1‐4 Remarks
●No other warranty is expressed or implied, except for the above mentioned.
●The remedies provided herein are the buyer’s sole and exclusive remedies.
TELECRANE shall not be liable for any direct, indirect, special, incidental or
consequential damages.
2. ATTENTION
2‐1 Attention
●Please carefully read the manual before installing and operating this device.
●Due to the complex nature of this equipment it is necessary to read the
entire manual before installation.
●Never dismantle the equipment by any unauthorized personnel, or
equipment may be damaged.
●This manual is for reference only. Pleases consult your distributor for
further assistance.
●The equipment has been strictly tested for quality before delivery from our
plant. However, this equipment must not be used in dangerous situations
or where damage may result.
●After the operation finished, please close the crane main power source, the
receiver power supply.
●Transmitter when not in use, should be placed in a safe place to avoid the
accidental touching the buttons by mistake.
●The crane should be equipped with main power relay, limit switch and
other safety devices.
●Don’t use equipment during lightening or high electrical interference
conditions.
●Make sure that the batteries are in good condition and power for receiver is
correct.
●Maintenance should only be done while the crane’s main power is off to
prevent electrical shock.
●The contents of this manual may be amended by the manufacturer without
notice.
●The manufacturer may introduce new functions to the equipment as
necessary; therefore, the descriptions may change.
2‐2 Precautions
●Operating in an industrial facility is relatively dangerous; therefore,
operator must have taken the adequate trainings in using F21‐E2 system.
●Those who operate the machine should be healthy and have good
judgment in regard to safety.
●Although the F21‐E2 transmitter is so durable and resistant for the
fluctuating temperature, it still needs to take care to prevent it from the
severe impact or pressure.
●During operation, if the power supply of the transmitter’s batteries is
insufficient, the transmitter will send out EMS signal first to de‐energize all
of motion relays inside the receiver to stop crane’s moving, and then the
LED indicator on transmitter will flash in red constantly. At this moment,
the batteries need to be replaced and all of two batteries should be
replaced at the same time.
●If the severe interference occurred the equipment should be stopped at
once.
●Please take the batteries out when the equipment will not be used for a
long time.
●Make sure "Procedures of Emergency" is fully known as following.
3. PROCEDURES OF EMERGENCY
In case of an Emergency, please follow the steps below and ask the distributor
for service immediately.
1. Press "EMS" button.
2. Turn the key to "OFF" position and remove it.
3. Switch off the main power of crane.
4. Advise the distributor to find out the reason.
4. HOW TO START
4‐1 F21‐E2 feature
EMS button
LED Indicator
Motion button
Receiver
Wiring diagram
Rotary KEY switch
4‐2 Operation
4‐2‐1 Procedure
1. Put two AA batteries on the release ribbon. And lock the battery cover.
Note: Before placing the batteries, make sure the Rotary KEY is on the
"OFF" position.
2. Turn the Rotary KEY into START position. (Or depend on the setting mode
of power on.)
3. In accordance with the function setting of pushbutton to operate
correctly.
4. After the operation, please do the following steps to turn off.
a) Press EMS button.
b) Turn the rotary key to "OFF" position.
c) Remove the batteries when the remote is not going to be used for a
long period of time.
4‐2‐2 Transmitter LED indicator
There is a 3‐stage power indicating function with LED display.
1."Green color": Sufficient power to operate transmitter.
2."Yellow color": Power is depleting. Operation must be stopped
immediately (for example: down the loads to ground) to replace
batteries.
3."Red color": Insufficient power. Transmitter will send out an emergency
stop signal to the receiver due to insufficient power. Operator should
avoid this situation in order to maintain the safety of operation.
5. RECEIVER POWER SELECTION
5‐1 Receiver power transformer voltage selection
F21‐E2 receiver provides with 5 kinds of Transformer (24V/48 VAC、48/110
VAC、48/220 VAC、110V/220 VAC、220V/380 VAC) that allows user to
choose based on the power input on site and the designated voltage will be
set when the receiver is made in factory.
5‐2 Change power supply voltage
1. Disconnect the power of receiver.
2. Remove the connector plug of the transformer from its original position.
3. Insert the connector plug into the new position.
4. Complete the procedure.
Transformer
24/48
48/110
48/220
110/220
220/380
Jumper
VAC
VAC
VAC
VAC
VAC
LO position
24VAC
48VAC
48VAC
110VAC
220VAC
HI position
48VAC
110VAC
220VAC
220VAC
380VAC
Note: Users are allowed to select the different power source according to the
respective requirement. However, the transformer must be changed.
Please check with your local distributor for replacement of the
transformer if necessary.
www.telecrane.com.tw
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Industry Canada Notice
Operation is subject to the following two conditions: (1) this device may not
cause interference and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Industry Canada Caution
This device complies with Industry Canada licence‐exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'IndustrieCanadaapplicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2012:12:11 13:51:29+08:00
Create Date                     : 2012:11:20 16:04:30+08:00
Metadata Date                   : 2012:12:11 13:51:29+08:00
Format                          : application/pdf
Title                           : Microsoft Word - user manual 1120.docx
Creator                         : Daphne
Document ID                     : uuid:4d72109c-9480-476b-adf4-b58c6086b0f2
Instance ID                     : uuid:15c641ca-888d-41c2-95e8-fb2f0be33e37
Has XFA                         : No
Page Count                      : 6
Author                          : Daphne

EXIF Metadata provided by EXIF.tools