Leedarson Lighting 5AA-SS-ZE-H0 Contact Sensor User Manual v1

Download:
Mirror Download [FCC.gov]
Document ID	3395671
Application ID	jQ2D6MhWTQydPH6NX1SJoQ==
Document Description	User Manual_v1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.12kB (426495 bits)
Date Submitted	2017-05-18 00:00:00
Date Available	2017-05-19 00:00:00
Creation Date	2017-05-17 13:11:49
Producing Software	Acrobat Distiller 10.1.13 (Windows)
Document Lastmod	2017-05-17 13:11:49
Document Title	Microsoft Word - User Manual_v1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	djin

We build your success in IoT.
Contact Sensor
Quick Start Guide
Meet Your LEEDARSON Contact Sensor
The Contact Sensor lets you know when door or windows is opened and can trigger different actions in
response to that open action (or close action).
Capabilities:

The LEEDARSON Contact Sensor is a universal ZigBee Contact Sensor.

The LEEDARSON Contact Sensor detects status of door or windows.

The LEEDARSON Contact Sensor is powered by CR2032 battery with 3 years battery life.

The LEEDARSON Contact Sensor is designed to be mounted on the door or windows.
Specification
Power Supply:
Battery
Operational Voltage:
3V
Battery Type:
CR2032
Battery Life:
3 years
Radio Protocol:
ZigBee
Radio Frequency:
2.4GHz
Range:
100ft LOS
Operational Temperature:
‐10Ԩ ~ + 50Ԩ
Standards Compliance:
FCC, CE
45.3(L)*31.1(W)*19.1(H)
for Main Body
45.3(L)*15.2(W)*18.4(H)
for Magnetic Part
Dimensions (mm):
How to connect a Contact Sensor
Use a pin to press the button in the main body of the sensor to include the Contact Sensor into the ZigBee
network.
Contact Sensor’s Inclusion Procedure:
1. Make sure the sensor is powered.
2. Press and hold the button for 3 second. This will cause a LED indicator to flash once per second.
3. Tap “Add device” in the LEEDARSON LDS App. The LDS App will search for the device.
4. The LED indicator will turn off to confirm a successful inclusion.
Button
Tip
When initially setting up the LEEDARSON Contact Sensor, it is recommended to perform the setup task
within 15 feet (4.5 meters) of the ZigBee Hub.
How to reset a Contact Sensor
Reset procedure deletes memory, including all information on the ZigBee network and the hub.
Contact Sensor’s Reset Procedure:
1. Make sure the sensor is powered.
2. Press and hold the button for 3 seconds.
3. Release the button.
4. LED indicator flashes once per second to confirm a successful reset.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained
between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : djin
Create Date                     : 2017:05:17 13:11:49+08:00
Modify Date                     : 2017:05:17 13:11:49+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 10.1.13 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - User Manual_v1
Creator                         : djin
Document ID                     : uuid:2bc19d0f-3ed1-4f88-a3c3-793125e37636
Instance ID                     : uuid:ce63a131-3776-4d54-a680-e7215c3352cf
Page Count                      : 5

EXIF Metadata provided by EXIF.tools