Leica Camera 1222 Flash Commander User Manual Air10s quick manual v4

Leica Camera AG Flash Commander Air10s quick manual v4

user_manual

LEICA SF C1The comprehensive instructions can be found under: https://de.leica-camera.com/Service-Support/Support/Downloads
Disposal of electrical and electronic equipment(Applies within the EU, and other European countries with segregated waste collection systems)This device contains electrical and/or electronic components and must therefore not be disposed of in general household waste! Instead, it should be disposed of at a recycling collection point provided by the local authority. This costs you nothing. If the device contains standard or rechargeable batteries, these must be removed first and also be disposed of in line with relevant regulations. Further information on the subject is available from your local administration, your local waste collection company, or in the store where you purchased this device.Declaration of Conformity (DoC)Hereby, “Leica Camera AG” declares that this product is in compliance with the essential requirements and other relevant provisions of Direc-tive 2014/53/EU. Customers can download a copy of the original DoC to our RE products from our DoC server: www.cert.leica-camera.comIn case of further questions, please contact:Leica Camera AG, Am Leitz-Park 5, 35578 Wetzlar, GermanyWireless Transmitter:Frequency range used: 2412 MHz to 2462 MHz (Central frequency WLAN)Max. output power: 13dBM (EIRP)The CE identification of our products documents compliance with the fundamental requirements of the applicable EU directives.For United Arab Emirates only:TRA REGISTERED No: ERxxxxx/yy DEALER No: DA0112968/13For US and Canada only:A recyclable lithium ion/polymer battery powersthis camera. Please call 1-800-8-BATTERY forinformation on how to recycle this battery.This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.FCC Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:To assure continued compliance, follow the attached installation instructions and use only shielded inter face cables with ferrite core when connecting to com put er or peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equip-ment.Trade Name: LEICAType No. 1222Responsible party/Support contact: Leica Camera Inc.1 Pearl Count, Unit A, Allendale, New Jersey 07401Tel.: +1 201 995 0051/ Fax: +1 201 995 1684technicalinfo@leicacamerausa.comThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Type No.: 1222 Tested To ComplyWith FCC StandardsFOR HOME OR OFFICE USEFCC ID: N5A1222This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR).For Canada only:CAN ICES-3 (B)/NMB-3(B)This device complies with RSS-210 of the IC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference,(2) This device must accept any interference received, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR).For Singapore onlyComplies withIDA StandardsDA106734
PairingBefore the pairing begins, make sure your NAS flashgun(s) areset to Auto Channel mode(2). Turn off both flashgun(s) and the Air 10s.1OFFHold Mode button for 1 second for open mode. Users need to turn off if they are using NAS flashgun(s) that do not support the Open mode.1OPEN Mode to Press the group selection button A B /C/ D/A B C Dselect a different group and press the same button again to end. Turn off the group by pressing when the group is blinking. Only MG10 supports the mix of TTL and M in advance group.2Press and hold Advance GroupA B C D1 sec. to change to the advance group Basic GroupA B C D &A B C D /Press to enable or disable the modeling light on flash.3Rotate the dial to adjust the Power of M mode / Flash exposure compensation of TTL mode when the group is blinking. Adjust power & TTLPress and hold to change zoom position when the group is blinking or rotate the dial to adjust manually.4Flash exposureFor the basic group A Bs :C DAll groups work in the same mode. To change different mode by pressing M/TTL mode button.For the advanced groups of :TTL and M mode can work in 4 advanced groups. To change mode between M and TTL of a selected group, press “M/TTL” button when the group blinks.A B C DHold the dedicated buttons(2) on your NAS flashgun(s) for 3 secondsuntil you hear the beeping sound.2HOLD3 Sec.Hold both Panel Lock button and Power on/off button for 3 secondsuntil the Pilot light is blinking in orange colour.3Blink!4Memorized!NAS flashgun(s) and Air 10s stop beeping and blinking after the pairing is done. Pairing setting remains unchanged even when both devices are powered off. Do not operate until the process finished.Control
Nomenclature1 Group selection button2 Group on/off button3 Modeling light button4 Shutter cable socket (2.5mm) 5 Mode Button6 LCD panel7 Select dial with buttonsChannel buttonHSS buttonBeep on/off button M.Zoom buttonPanel Lock/Unlock button (hold 1sec.)8 Pilot button (Test flash button)9 Power On/Off switch 10 Unlock button11 Micro SD card slot (for firmware update)12 Strap hole13 Battery compartment door14 AF-assist light (1)15 Hotshoe contacts 611041389532714151112Hold the Channel button for 1 second to change wireless channel. Rotate the dial to select Channels 1(3) - 8. (i60A, Di700A and Air R do not support Channel 1. Set all items to same channel between Channels 2 - 8 for pairing and shooting.) Hold the Channel button for 1 second again to confirm. Change the Channel setting of NAS flashgun(s) same as Air 10s. For details, please refer to the specific user manual(2).Channels 1(3)- 8Channel Setting12HOLD 1 Sec.Auto ChannelWhen NAS flashgun(s) are set to Auto Channel mode, it automatically follows the Channel setting of Air 10s when the users are changing the flashgun(s).When NAS flashgun is set and fix the Channel setting in Channels 1(3) - 8 , they do not automatically follow the Channel setting of Air 10s. User has to set NAS flashgun manually in the same channel as Air 10s to keep the pairing.
Important noticeMemoryThe pairing setting is memorized and remains unchanged when power on/ off.Energy savingThe display dims in 30 seconds. Automatically sleep in 2 minutes whenAir 10s and camera are not in use. Press any button on Air 10s or the camera shutter to cancel the energy saving mode. Air 10s completely turns off in 60 minutes automatically when it is not in use. To turn on again press the on/off button.Turn on/offTo turn off the Air 10s manually, press on/ off switch and hold it for 1 second.

Navigation menu