Leica Geosystems CPD LD2BT Leica Disto D1 User Manual My
Leica Geosystems AG, CPD Leica Disto D1 My
Contents
- 1. RFF-LD2BT Userman
- 2. 15_Leica Disto D1 UserMan
15_Leica Disto D1 UserMan
Leica DISTOTM D1
The original laser distance meter
Technical data
Te c h n ica lda ta
Leica DISTO™ D1 3
General
Accuracy with favourable conditions * 2 mm / 0.08 in ***
Accuracy with unfavourable conditions ** 3 mm / 1/8" ***
Range with favourable conditions * 0.05 - 40 m / 0.16 - 120 ft ***
Range with unfavourable conditions ** 0.05 - 30 m / 0.16 - 100 ft ***
Smallest unit displayed 0.1 mm / 1/32 in
Laser class 2
Laser type 635 nm, <1 mW
ø laser point | at distances 6 /30 /60 mm | 10/ 50/ 100 m
Protection class IP54 (dust- and splash water protected)
Auto. laser switch off after 90 s
Auto. power switch off after 180 s
Bluetooth® Smart Bluetooth® v4.0
Range of Bluetooth® Smart <10m
Battery durability (2 x AAA) up to 10000 measurements
Dimension (H x D x W) 115 x 43.5 x 23.5 mm | 4.53 x 1.71 x 0.93 in
Weight (with batteries) 87 g/ 3.07 oz
Temperature range Storage | Operation -25 to 70°C/ -13 to 158°F | -0 to 40°C/ 32 to 104°F
* favourable conditions are: white and diffuse reflecting target (white painted wall), low background illumination and moderate temperatures.
** unfavourable conditions are: targets with lower or higher reflectivity or high background illumination or temperatures at the upper or lower end of the specified temperature range.
*** Tolerances apply from 0.05 m to 5 m with a confidence level of 95%.
With favourable conditions the tolerance may deteriorate by 0.10 mm/m for distances above 5 m.
With unfavourable conditions the tolerance may deteriorate by 0.15 mm/m for distances above 5 m.
Technical data
Functions
Distance measuring yes
Permanent measuring yes
Beep yes
Illuminated display yes
Bluetooth® Smart yes
Leica DISTO™ D1 4
Instrument Set-up
Ins trume n tSet-up
Introduction
The safety instructions (see Safety
Instructions) and the user manual
should be read through carefully
before the product is used for the first
time.
The person responsible for the
product must ensure that all users
understand these directions and
adhere to them.
The symbols used have the following
meanings:
WARNING
Indicates a potentially hazardous situ-
ation or an unintended use which, if
not avoided, will result in death or ser-
ious injury.
CAUTION
Indicates a potentially hazardous situ-
ation or an unintended use which, if
not avoided, may result in minor injury
and/or appreciable material, financial
and environmental damage.
Important paragraphs which
must be adhered to in practice
as they enable the product to be
used in a technically correct and
efficient manner.
5
Leica DISTO™ D1
Instrument Set-up
Insert batteries
To ensure a reliable use, we recom-
mend using high quality Alkaline bat-
teries. Change batteries when
battery symbol is flashing.
Leica DISTO™ D1 6
Instrument Set-up
Switching ON/OFF
Device is turned OFF.
Leica DISTO™ D1 7
Instrument Set-up
Clear
Undo last action. Leave actual function, go to default
operation mode.
Leica DISTO™ D1 8
Instrument Set-up
Settings
Press both keys simultaneousley. Switch between the following units:
0.000 m
0'00" 1/16
0.0000 m
0.000 in
0.00 ft
0 in 1/16
Leica DISTO™ D1 10
Operations
Ope rations
Measuring single distance
Aim active laser at target.
Target surfaces: Measuring
errors can occur when meas-
uring to colourless liquids, glass,
styrofoam or permeable sur-
faces or when aiming at high
gloss surfaces. Against dark
surfaces the measuring time
increases.
11
Leica DISTO™ D1
Operations
Permanent measuring
The last value measured is displayed
in the main line.
Stops permanent measuring.
Leica DISTO™ D1 12
Operations
Bluetooth® Smart
DISTO™ sketch. Use App for
Bluetooth® data transfer.
Bluetooth® Smart is always act-
ive when the device is switched
on. Connect the device with
your smart-phone, tablet,
laptop.. Measurement values
will be transferred automatically
right after a measurement. The
efficient and innovative
Bluetooth® Smart module (with
the new Bluetooth® standard
V4.0) works together with all
Bluetooth® Smart Ready
devices. All other Bluetooth®
devices do not support the
energy saving Bluetooth®
Smart Module, which is integ-
rated in the device.
We provide no warranty for free
DISTO™ software and offer no
support for it. We accept no liab-
ility whatsoever arising from the
use of the free software and we
are not obliged to provide cor-
rections nor to develop
upgrades. A wide range of com-
mercial software can be found
on our homepage. Apps for
Android® or iOS can be found in
special internet shops. For more
details, see our homepage.
Leica DISTO™ D1 13
Message Codes
Mes s a g e C o d e s
Leica DISTO™ D1 14
No. Cause Correction
204 Calculation error Perform measurement again.
220 Hardware error Contact your dealer
240 Data transfer error Connect device and repeat procedure
252 Temperature too high Let device cool down.
253 Temperature too low Warm device up.
255 Received signal too weak, measuring time too long Change target surface (e.g. white paper).
256 Received signal too high Change target surface (e.g. white paper) .
257 Too much background light Shadow target area.
* If other message codes are displayed frequently even the instrument has been switched off and on, please contact your dealer.
Care
Care
lClean the device with a damp, soft cloth.
lNever immerse the device in water.
lNever use aggressive cleaning agents or
solvents.
Leica DISTO™ D1 15
Warranty
Warra n ty
Warranty under PROTECT by Leica
Geosystems
Lifetime Manufacturer´s Warranty
Warranty coverage for the entire usage time of
the product under PROTECT according to Leica
Geosystems International Limited Warranty and
PROTECT General Terms & Conditions set out
under www.leica-geosystems.com. Free of
charge repair or replacement of all products or
any parts under PROTECT that suffer defects as
a result of faults in materials or workmanship.
3 Years No Cost
Additional services should the product under
PROTECT become defective and require ser-
vicing under normal conditions of use, as
described in the user manual, at no additional
charge.
To receive the "3 Years No Cost" period, the
product under PROTECT must be registered at
myworld.leica-geosystems.com within 8 weeks of
the purchase date. If the product under
PROTECT is not registered, a "2 years No Cost"
period applies.
Leica DISTO™ D1 16
Safety instructions
Sa fety ins tru c tio n s
The person responsible for the instrument
must ensure that all users understand these
directions and adhere to them.
Leica DISTO™ D1 17
Safety instructions
Symbols used
The symbols used have the following meanings:
WARNING
Indicates a potentially hazardous situation or an
unintended use which, if not avoided, will result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation or an
unintended use which, if not avoided, may result in
minor injury and/or appreciable material, financial
and environmental damage.
Important paragraphs which must be
adhered to in practice as they enable the
product to be used in a technically correct
and efficient manner.
Leica DISTO™ D1 18
Safety instructions
Permitted use
lMeasuring distances
lData transfer with Bluetooth®
Leica DISTO™ D1 19
Safety instructions
Prohibited use
lUsing the product without instruction
lUsing outside the stated limits
lDeactivation of safety systems and
removal of explanatory and hazard labels
lOpening of the equipment by using tools
(screwdrivers, etc.)
lUse of accessories from other man-
ufacturers without express approval
lCarrying out modification or conversion
of the product
lDeliberate dazzling of third parties; also in
the dark
lInadequate safeguards at the surveying
site (e.g. when measuring on roads, con-
struction sites, etc.)
lDeliberate or irresponsible behaviour on
scaffolding, when using ladders, when
measuring near machines which are run-
ning or near parts of machines or install-
ations which are unprotected
lAiming directly in the sun
Leica DISTO™ D1 20
Safety instructions
Hazards in use
WARNING
Watch out for erroneous measurements if the
instrument is defective or if it has been dropped or
has been misused or modified. Carry out periodic
test measurements. Particularly after the instru-
ment has been subject to abnormal use, and
before, during and after important meas-
urements.
CAUTION
Never attempt to repair the product yourself. In
case of damage, contact a local dealer.
WARNING
Changes or modifications not expressly approved
could void the user´s authority to operate the
equipment.
Leica DISTO™ D1 21
Safety instructions
Areas of responsibility
Responsibilities of the manufacturer of the ori-
ginal equipment:
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Internet: www.leica-geosystems.com
The company above is responsible for supplying
the product, including the User Manual in a com-
pletely safe condition.
The company above is not responsible for third
party accessories.
Responsibilities of the person in charge of the
instrument:
lTo understand the safety instructions on
the product and the instructions in the
User Manual.
lTo be familiar with local safety regulations
relating to accident prevention.
lAlways prevent access to the product by
unauthorised personnel.
Leica DISTO™ D1 23
Safety instructions
Disposal
CAUTION
Flat batteries must not be disposed of with house-
hold waste. Care for the environment and take
them to the collection points provided in accord-
ance with national or local regulations.
The product must not be disposed with household
waste. Dispose of the product appropriately in
accordance with the national regulations in force
in your country. Adhere to the national and coun-
try specific regulations.
Product specific treatment and waste man-
agement can be downloaded from our
homepage.
Leica DISTO™ D1 24
Safety instructions
Electromagnetic Compatibility
(EMC)
WARNING
The device conforms to the most stringent require-
ments of the relevant standards and regulations.
However, the possibility of causing interference in
other devices cannot be totally excluded.
Japanese Radio Law Compliance
This device is granted pursuant to the Japanese
Radio Law 電波法. This device should not be
modified otherwise the granted designation num-
ber will become invalid.
Leica DISTO™ D1 25
Safety instructions
FCC statement (applicable in U.S.)
This equipment has been tested and found to com-
ply with the limits for a Class B digital instrument,
pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential install-
ation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio com-
munications.
However, there is no guarantee that interference
will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
lReorient or relocate the receiving
antenna
lIncrease the separation between the
equipment and the receiver
lConnect the equipment into an outlet on
a circuit different from that to which the
receiver is connected
lConsult the dealer or an experienced radi-
o/TV technician for help
This device complies with part 15 of the FCC
rules. Operation is subjected to the following two
conditions:
lThis device may not cause harmful inter-
ference, and
lthis device must accept any interference
received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement
The radiated rf output power of the instrument is
below the FCC radio frequency exposure limits for
portable devices according to KDB 447498.
Leica DISTO™ D1 26
Safety instructions
ISED Statement (applicable in
Canada)
This device complies with Industry Canada's
license-exempt RSSs. Operation is subject to the
following two conditions:
lThis device may not cause harmful inter-
ference, and
lthis device must accept any interference,
including interference that may cause
undesired operation of the device.
Radio Frequency (RF) Exposure Compliance
Statement
The radiated rf output power of the instrument is
below the Health Canada's Safety Code 6 exclu-
sion limit for portable devices (radiated element
separation distance between the radiating ele-
ment and user and/or bystander is below 20 cm).
Leica DISTO™ D1 27
Safety instructions
Use of the product with Bluetooth®
WARNING
Electromagnetic radiation can cause disturbances
in other equipment, in installations (e.g. medical
ones such as pacemakers or hearing aids) and in
aircraft. It can also affect humans and animals.
Precautions:
Although this product conforms to the most strin-
gent standards and regulations, the possibility of
harm to people and animals cannot be totally
excluded.
lDo not use the product near petrol sta-
tions, chemical plants, in areas with a
potentially explosive atmosphere and
where blasting takes place.
lDo not use the product near medical
equipment.
lDo not use the product in airplanes.
lDo not use the product near your body
for extended periods.
Leica DISTO™ D1 28
Safety instructions
Laser classification
The device produces visible laser beams, which
are emitted from the instrument: It is a Class 2
laser product in accordance with:
lIEC60825-1 : 2014 „Radiation safety of
laser products“
Laser Class 2 products:
Do not stare into the laser beam or direct it
towards other people unnecessarily. Eye pro-
tection is normally afforded by aversion responses
including the blink reflex.
WARNING
Looking directly into the beam with optical aids
(e.g. binoculars, telescopes) can be hazardous.
CAUTION
Looking into the laser beam may be hazardous to
the eyes.
Wavelength
620 - 690 nm
Maximum radiant output power for classification
< 1 mW
Pulse duration
> 400 ps
Pulse repetition frequency
320 MHz
Beam divergence
0.16 x 0.6 mrad
Leica DISTO™ D1 29
Safety instructions
Labelling
Subject to change (drawings, descriptions and
technical data) without prior notice.
Leica DISTO™ D1 30