Leica Geosystems CPD LD5PS Leica DISTO S910 User Manual S910 en

Leica Geosystems AG, CPD Leica DISTO S910 S910 en

15_[Leica DISTO S910] UserMan

Leica DISTOTM S910 805080 1ENTable of ContentsInstrument Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2Basic measuring screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3Selection screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3Pointfinder (Viewscreen)- - - - - - - - - - - - - - - - - - - - - - - - - - - - 4Icons on Status bar - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4Charging the Li-Ion battery via USB - - - - - - - - - - - - - - - - - - - - - 5Using the Smart Base - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6Using the Smart Base Extension - - - - - - - - - - - - - - - - - - - - - - - 6Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7Using the Touch Screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8Message Codes- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8Permanent / Minimum-Maximum measuring - - - - - - - - - - - - - - - 8Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8Pointfinder (Viewscreen)- - - - - - - - - - - - - - - - - - - - - - - - - - - - 9Screenshot- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9Settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10Tilt units - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10Distance units- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11Beep ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12Digital level ON/OFF- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12De-/Activate keylock - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12Switch on with keylock - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12Bluetooth® /WIFI - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13Calibration of tilt sensor (Tilt Calibration) - - - - - - - - - - - - - - - - 15Personalized favorites- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16Illumination - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16Touch Screen ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - 16Date and Time - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17Compass Adjustment - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17Offset - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18Reset - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18Functions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19Timer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20Calculator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20Adjusting measuring reference - - - - - - - - - - - - - - - - - - - - - - - 21Memory - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22Measuring single distance - - - - - - - - - - - - - - - - - - - - - - - - - - - 22Smart Horizontal Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22Level - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23Volume - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24Photo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25Compass - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26Gallery - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27Triangular area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28Height-profile measurement - - - - - - - - - - - - - - - - - - - - - - - - - 29Sloped objects - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 30Height tracking- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 31Trapezium - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 32Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 33Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 34Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 35Width - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 36Diameter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 37Area from Photo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 38Pointdata transmission- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 39Smart Angle measuring - - - - - - - - - - - - - - - - - - - - - - - - - - - - 40Point to point function / distance- - - - - - - - - - - - - - - - - - - - - - 41Smart Area measuring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 42Data capture in DXF-file - - - - - - - - - - - - - - - - - - - - - - - - - - - 43Technical Data- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 44Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 45Care - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 45Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 46Safety Instructions- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 46Areas of responsibility - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 46Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 47Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 47Disposal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 47Electromagnetic Compatibility (EMC) - - - - - - - - - - - - - - - - - - - 47FCC statement (applicable in U.S.) - - - - - - - - - - - - - - - - - - - - - 48Déclaration FCC, applicable aux Etats-Unis - - - - - - - - - - - - - - - 48Normativa FCC (aplicable en EE UU) - - - - - - - - - - - - - - - - - - - 49Use of the product with Bluetooth®- - - - - - - - - - - - - - - - - - - - 49Laser classification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50
Leica DISTOTM S910 805080 2ENInstrument Set-upIntroductionThe safety instructions and the user manual should be read through carefully before the product is used for the first time.The person responsible for the product must ensure that all users understand these directions and adhere to them.The symbols used have the following meanings:WARNINGIndicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.CAUTIONIndicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage.Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.iOverviewDisplayOn/MeasurePointfinder(Viewscreen)NavigationClear / OffSelection keys linked to symbols aboveEnter / EqualFunction screenAdd / Subtract
Leica DISTOTM S910 805080 3ENInstrument Set-upBasic measuring screenStatus barFavoritesMain lineActive functionTap here to startON/DIST in a dis-tance functionSelection screenFUNCSettingsFunction /SettingsHelp function
Leica DISTOTM S910 805080 4ENInstrument Set-upPointfinder (Viewscreen)1x24.210mZoom stageFavoritesIlluminationadjustmentwith navigationkeys left andrightActive functionZoom with navigation keys up and downCrosshairSpread 2 fingers apart to zoomon the touch screenIcons on Status barScroll up and down for further resultsBattery powerBluetooth® is switched onBluetooth® connection establishedDevice is not leveledOffset is activated and subtracts the defined value from measured distanceOffset is activated and adds the defined value from measured distanceWiFi client mode activatedDISTO connected as client to WiFiZoomDevice is leveledDISTO WiFi hotspot activatedOther device connected to DISTO WiFi hotspotDevice is measuringMeasuring reference
Leica DISTOTM S910 805080 5ENInstrument Set-upCharging the Li-Ion battery via USBCharge the battery before using it for the first time. Use the provided cable to charge the battery. Plug the small end of the cable into the port of the device, and plug the end of the charger into an electrical socket. Select the appro-priate connector for your country. The device cannot be used while it is charging.The computer can also be used to charge the device, but this takes more time. If the device is connected to the computer via USB cable, you can download or delete the gallery. It is not possible to upload any data. When you charge the battery, the following icons show the status:4 hCharging Fully chargedCAUTIONConnecting the charger improperly may cause serious damage to the device. Any damage caused by misuse is not covered by the warranty. Use only Leica-approved chargers, batteries, and cables. Unapproved chargers or cables can cause the battery to explode or damage the device.If the device is connected to the computer via USB cable, you can download or delete the gallery. It is not possible to upload any data.iCharge batteries when battery symbol is flashing. While charging, the device may heat up. This is normal and should not affect the device’s lifespan or performance. If the battery gets hotter than 40°C / 104°F, the charger stops. At a recommended storage temperature of -20°C to +30°C (-4°F to +86°F), batteries containing a 50% to 100% charge can be stored up to 1 year. After this storage period the batteries must be recharged. To save energy, unplug the charger when not in use.
Leica DISTOTM S910 805080 6ENInstrument Set-upUsing the Smart BaseUsing the Smart Base ExtensionUnlockLockTripod orAdapter threadFold out Smart Base. Use it as mini tripod.The Smart Base Extension supports stable targeting without tilting.iDo not move or tilt the Smartbase during measuring.We recommend to use a tripod with the Leica FTA360-S adapter.
Leica DISTOTM S910 805080 7ENOperationsOperationsUsing the Touch ScreeniUse only fingers to use the touch screen.Do not allow the touch screen to come into contact with other elec-trical devices.Electrostatic discharges can cause the touch screen to malfunction.Do not allow the touch screen to contact water. The touch screen may malfunction in humid conditions or when exposed to water.To avoid damaging the touch screen, do not tap it with anything sharp or do not apply excessive pressure to it with your fingertips.TappingTap on the display to open an on-screen button or to make a selection. Tapping on the icon in the middle of the bottom line activates the distance measurement or triggers the camera.DraggingDrag on the display to move to prior or to next screen in the galerie function.PinchingSpread 2 fingers apart to zoom if pointfinder is activated.iInstead of using the touch screen, the nor-mal keypad but-tons can be used also.
Leica DISTOTM S910 805080 8ENOperationsSwitching ON/OFF Clear Message CodesONOFF2 secDevice is turned OFF.iIf no key is pressed for 180 sec, the device switches off au-tomatically.1xUndo last action.2xLeave actual func-tion, go to default operation mode.If the info icon appears with a number, observe the instructions in section "Message Codes". Example:Permanent / Minimum-Maximum measuring12 sec8.532 mUsed to measure room diagonals (maximum val-ues) or horizontal distance (minimum values)The minimum and maximum dis-tance measured is displayed (min, max.). The last value measured is displayed in the main line.min. max.2Stops permanent / minimum-maximum measuring.3Add / Subtract7.332 m1The next meas-urement is added to the previous one.2The next meas-urement is sub-tracted from the previous one.2x7.332 m12.847 m320.179 m4iThis process can be repeated as required. The same process can be used for adding or subtracting areas or volumes.
Leica DISTOTM S910 805080 9ENOperationsPointfinder (Viewscreen)1x0.00m1OV*1x2x4x21x0.00m3Exit pointfinder (viewscreen).4iThis is a great help for outdoor measuring. The integrated pointfinder (viewscreen) shows the target on the display. The device measures in the middle of the cross hair, even if the laser dot is not visible. Parallax errors occur when the pointfinder camera is used on close targets, with the effect that the laser appears dis-placed in the crosshair. In this case rely on the real laser dot. * OV = OverviewScreenshot1x0.00m12 secScreenshot photo is saved in gallery.
Leica DISTOTM S910 805080 10ENSettingsOverview12Tilt unitsWiFi / Bluetooth®Digital levelKeypad lockIlluminationFavoritesCompass adjustment Touch screenResetInformationBeepTilt calibrationDistance unitsOffsetDate and Time Tilt units12360.0°± 180.0°± 90.0°0.00 %0.0 mm/m0.00 in/ftSwitch between the following units:34Confirm setting.Exit settings.5
Leica DISTOTM S910 805080 11ENSettingsDistance units120.00 m0.000 m0.0000 m0.0 mm0.00 ft0.00 in0 in 1/320'00" 1/320.00 m0.000 m0.0000 m0.0 mm0.00 ft0'00" 1/320'00" 1/160'00" 1/80'00" 1/4 0.00 in 0 in 1/320 in 1/160 in 1/80 in 1/40.000 ydArt. No. 805080:3US-Model Art. No. 808183:Switch between the following units:4Confirm setting.Exit settings.5
Leica DISTOTM S910 805080 12ENSettingsBeep ON/OFF1ON2To switch ON, repeat procedure.OFFExit settings.3Digital level ON/OFF1ON2To switch ON, repeat procedure.OFFExit settings.3iThe digital level is displayed in the status bar. De-/Activate keylock Switch on with keylock1OFF2To deactivate, repeat procedure. The keylock is active if device is switched off. ONExit settings.31within 2 sec2
Leica DISTOTM S910 805080 13ENSettingsBluetooth® /WIFI1ONOFFOFF2OFFExplanation see info box below.Special Settings for data transfer.Exit settings.3iDefault mode: Bluetooth®/WIFI is switched on and black Bluetooth®/WIFI icon is displayed in status bar. Blue Bluetooth®/WIFI icon in sta-tus line is displayed if device is connected with Blue-tooth®/WIFI.iSpecial Bluetooth® Settings Figure Mode: Use this mode if the data needs to be transferred in figures, e.g. working with spread sheets. Ft/in fractional is converted into ft/in decimal. Text Mode: Use this mode if the data needs to be transferred as text, e.g. working with word processing programs. App Mode: Use this mode to transfer the data using an App.Special properties: ENCRYPTED is the default setting. In case of trou-ble with data transfer, select mode UNENCRYPTED.Allows the arrow keys to move the cursor on your computer.sends the value of the main line to the computer.Allows the arrow keys to move the cursor on your computer.sends the value of the main line to the computer.Device is connected. Favorites disappear and two softkeys appear: Device is connected. Favorites disappear and two softkeys appear: iSpecial WIFI Settings WiFi: Another device acts as hotspot. Recommended for GIS applications. WiFi: DISTO acts as hotspot. Data transfer unsecured or secured with serial number as password. Recommended for stand-ard use.
Leica DISTOTM S910 805080 14ENSettingsiConnect the device with your smart phone, tablet, laptop,…The actual measurement is transferred automatically if Blue-tooth® connection is established. To transfer a result from the main line, press =. Bluetooth® switches off as soon as the laser distance meter is switched off.We provide no warranty for free DISTO™ software and of-fer no support for it. We accept no liability whatsoever arising from the use of the free software and we are not obliged to provide corrections nor to develop upgrades. A wide range of commercial software can be found on our homepage. Apps for Android® or Mac iOS can be found in special internet shops. For more details, see our homepage.The efficient and innovative Bluetooth® Smart module (with the new Bluetooth® standard V4.0) works together with all Bluetooth® Smart Ready devices. All other Blue-tooth® devices do not support the energy saving Blue-tooth® Smart Module, which is integrated in the device.Bluetooth® data transfer
Leica DISTOTM S910 805080 15ENSettingsCalibration of tilt sensor (Tilt Calibration)123Place device on absolutely flat surface.180°4180°5Turn the device horizontally by 180° and place it again on absolutely flat surface.67Place device on absolutely flat surface.180°8180°9Turn the device horizontally by 180° and place it again on absolutely flat surface.10iAfter 2 sec the device goes back to the basic mode.
Leica DISTOTM S910 805080 16ENSettingsPersonalized favorites1Favorite23Select favorite function.4Press selection key left or right. Function is set as favorite above the corresponding se-lection key.iSelect your favorite functions for quick access. Short cut:Press 2 sec on a selection-key in the measuring mode. Select your favorite function and press again short on the corresponding se-lection key.Illumination11/621/62/63/64/65/66/63Select brightness.4Confirm setting.Exit settings.5iTo save power re-duce bright-ness if not necessary. Touch Screen ON/OFF1OFF2To deactivate, repeat procedure. ONExit settings.3
Leica DISTOTM S910 805080 17ENSettingsDate and Time1200 : 003Set time (hh:mm)2013-04-084Set date (yyyy-mm-dd)Exit settings.5Compass AdjustmentiDepending on your geographic location, the angle of declination may vary from other locations, as the geographic and magnetic poles are aligned. However, if the reference location is not selected, the difference in declination between the poles can differ greatly. For best results, select the nearest geographic reference point using the steps below.Adjusting the magnetic declination12CH-Zürich3Select the nearest loca-tion and the device ad-justs the declination accordingly. 4ConfirmBackExit settings.5
Leica DISTOTM S910 805080 18ENSettingsOffset121.012 m3Select digit.1.012 m4Adjust digit.5Approve value.Exit settings.6iAn offset adds or subtracts a specified value automatically to or from all measurements. This func-tion allows tolerances to be taken into account. The offset icon is displayed.Reset12Second confirmation with selection keys:3Refuse: Confirm:Exit settings.4iReset returns the instrument to the factory settings. All custom-ized settings and memories are lost. A HARDWARE-RESET is done by pressing 15 sec on ON/DIST key.
Leica DISTOTM S910 805080 19ENFunctionsOverviewTimerPointdata transmissionSmart AngleMemorySinlge Distance MeasurementLevelSmart Area measuring functionPoint to point function / distancePhoto Compass Data capture in DXF-fileAreaHeight TrackingSmart Horizontal Mode Measuring on sloped objectsPythagoras (2-point)VolumeCalculatorWidthStake out DiameterHeight-profile Measurement Trapezium GalleryArea from Photo Adjusting measuring reference Triangle AreaPythagoras (3-point)
Leica DISTOTM S910 805080 20ENFunctionsTimer12Off30 sec10 sec2 sec5 sec3Select release time.4Confirm setting.iThe self release starts if ON/Measure key is pressed.Calculator12C/CE =3Select key on display.Confirm every key.Use selection keys for clear or result.iThe measurement result from the main line is taken over to the calcula-tor and can be used for further calcu-lations. Ft/in fractions are converted into ft/in decimal.To take over a result from the calcu-lator in the basic mode press DIST before leaving the calculator function.
Leica DISTOTM S910 805080 21ENFunctionsAdjusting measuring reference123Distance is measured from the rear of the de-vice (standard setting).Distance is measured from the front of the de-vice (lock symbol = per-manently).Distance is measured from Smart Base con-nectionDistance is measured from Smart Base base-plateiThe orienta-tion of the Smart Base is automatically detected and the zero point is accordingly adjusted. 4Confirm setting.iIf device is switched off, reference goes back to standard set-ting (rear of the device).
Leica DISTOTM S910 805080 22ENFunctionsMemory128.449 m8.449 m3Switch between measurements.Take over value for further actions.Delete memory.4Use Up/Down navigation keys to show more detailed results of the speci-fic measurement.iShort cutMeasuring single distance12Aim active laser at target.38.532 m4iTarget surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or semi-permea-ble surfaces or when aiming at high gloss surfaces. Against dark surfaces the measuring time in-creases.Smart Horizontal Mode12Aim laser at target.3zxy40.8 °xyz5.204 m0.032 m4.827 m4(up to 360° and a transverse tilt of ±10°)
Leica DISTOTM S910 805080 23ENFunctionsLevel120.3°90°0°3iDisplays inclinations of 360° with a transverse inclination of +/- 10°. In-strument beeps at 0° and 90°. Ideal for horizontal or vertical adjustments.Area123Aim laser at first target point.45Aim laser at sec-ond target point.20.276 m 3.9I0 m 6.228 m24.352 m2First distanceSecond distanceCircumferenceArea6iThe result is shown in the main line and the measured value above. Partial Measurements / Painter function: Press + or - before starting the first measure-ment. Measure and add or subtract distanc-es. Finish with =. Measure 2nd length.
Leica DISTOTM S910 805080 24ENFunctionsVolume123Aim laser at first target point.45Aim laser at sec-ond target point.67Aim laser at third target point.2.431 m2.338 m5.744 m32.653 m3First distanceSecond distanceThird distanceVolume816.164 m39.300 m213.430 m29Use Up/Down navigation keys to show more re-sults.Ceiling/floor areaWall areasCircumference
Leica DISTOTM S910 805080 25ENFunctionsPhoto11x2OV*2x3Take photo.4Exit.5iTap on the camera icon in the mid-dle of the bottom line to take a pho-to.For screenshots, press camera key for 2 sec.* OV = Overview
Leica DISTOTM S910 805080 26ENFunctionsCompass12Calibrate Compass?Refuse Confirm0.0°NThe arrow always points to true north.3Exit.4iAt the following places the compass probably does not work correctly: • Inside of buildings• Close to high voltage lines (e.g. on train platforms)• Close to magnets, metal objects or electrical household appliancesiIf an error message occurs, the device is tilted too much (>20° over the front / > 10° sidewise). Calibration of Compass:iThe compass has to be cali-brated before every first measurement after switching on the device.Rotate the device slowly in a figure 8 motion until OK icon appears on the display.iAfter 2 sec the device goes back to the compass mode.
Leica DISTOTM S910 805080 27ENFunctionsGallery11x21x2013 - 07 - 03_13:252011x2013 - 07 - 03_13:25:251x13 - 07 - 03_13:25- 03_13:03- 07_13:25_13:257 1x2013 - 07 - 03_13:253Exit.4iIf the device is connected to the computer via USB cable, you can download or delete the gallery. It is not possible to upload any data.
Leica DISTOTM S910 805080 28ENFunctionsTriangular area123Aim laser at first target point.45Aim laser at sec-ond target point.67Aim laser at third target point.4.855 m22.425 m4.129 m4.248 mTriangular area8First distanceSecond distanceThird distance33.60°10.802 m9Use Up/Down navigation keys to show more re-sults.CircumferenceAngle between first and second measurement
Leica DISTOTM S910 805080 29ENFunctionsHeight-profile measurement12REF0Aim at reference point (REF).34REF102345hdAim at additional points 1-x.5dh2.042 m0.054 mHorizontal distance to deviceHeight difference to reference point (REF). 6Exit function.72xiIdeal for measuring of height differences to a reference point. Can be also used to meas-ure profiles and terrain sections. After meas-uring the reference point, the horizontal distance and height is displayed for each fol-lowing point.
Leica DISTOTM S910 805080 30ENFunctionsSloped objects123Aim laser at upper target point.45Aim laser at lower target point.11.00 ° -3.440 m 30.367 m5.452 mP2 distanceVertical height be-tween both pointsP2 angleDistance between both points6-4.230 m39.10 °7Use Up/Down navigation keys to show more re-sults.Horizontal distance between both pointsIncluded angle be-tween both pointsiIndirect distance measuring between 2 points with addi-tional results. Ideal for applications such as length and slope of roof, height of chimneys,…It is important, that the instrument is positioned in the same vertical plane as the 2 measured points. The plane is defined of the line between the 2 points. This means, that the device on the tripod is only moved vertically and not turned horizontally to reach both points.
Leica DISTOTM S910 805080 31ENFunctionsHeight tracking12P0PxAim laser at lower point.34P0PxAim laser at upper points and angle/ height tracking starts automatically.5xyP0 y29.89 °6.271 m-10.55 °3.475 mP0Pxz6= Tracking height if device is turned on tripod= Tracking angle if device is turned on tripod44.80 °6.271 m-10.55 °8.478 m7Stops height tracking.z7.160 m8Use Up/Down navigation keys to show more re-sults.iHeights of buildings or trees without suitable reflective points can be deter-mined. At the bottom point, distance and tilt is measured - which needs a re-flective laser target. The upper point can be targeted with the pointfinder / crosshair and does not need a reflec-tive laser target as only the inclination is measured.
Leica DISTOTM S910 805080 32ENFunctionsTrapezium123Aim laser at upper point.45Aim laser at 2nd point.xxyhyh70.80°5.790 m13.459 m16.440 m620.9 °78.383 m27Use Up/Down navigation keys to show more re-sults. Trapezium area
Leica DISTOTM S910 805080 33ENFunctionsStake outiTwo different distances (a and b) can be entered to mark off de-fined measured lengths.123abba = b123abba = b121.012 m3Select digit.1.012 m4Adjust digit.5Approve value "a".0.625 m6Adjust value "b".7Approve value "b" and start meas-urement.8Move device slowly along the stake-out line. The distance to the next stake out point is displayed.0.240 m0.625 m0.240 m is missing up to next 0.625 m distance.Next stake out distanceiWhen approaching a stake out point to less than 0.1 m the instrument starts to beep. The function can be stopped by pressing the CLEAR/OFF button.
Leica DISTOTM S910 805080 34ENFunctionsPythagoras (2-point)123Aim laser at first target.45Aim laser at second target.13.207 m21.383 m25.133 m6iThe result is shown in the main line. Pressing the measuring key for 2 sec in the function ac-tivates automatically Minimum or Maximum measure-ment. We recommend to use the pythagoras only for indirect horizontal measuring. For height measuring (vertical) it is more precise to use a function with the inclination measuring.
Leica DISTOTM S910 805080 35ENFunctionsPythagoras (3-point)123Aim laser at first target.45Aim laser at sec-ond target.67Aim laser at third target.20.571 m23.018 m21.264 m24.298 m8iThe result is shown in the main line. Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum meas-urement. We recommend to use the pythagoras only for indi-rect horizontal measuring. For height measuring (vertical) it is more precise to use a function with inclination measurement.
Leica DISTOTM S910 805080 36ENFunctionsWidth1-.--- m1x2 16.42m3It is absolutely necessary to aim with the laser per-pendicular to the object.OV*1x2x4x4If necessary, use the Zoom for precise aiming.* OV = Overview1x16.42 m5Select arrows with the cursor keys or by tapping on the display and adjust with softkeys. Corre-sponding width is calcu-lated.Confirm measuremtent.616.42 m27.539 m7Distance to objectExit.8
Leica DISTOTM S910 805080 37ENFunctionsDiameter1-.--- m1x2Ø3Aim laser perpendicular to the middle of the round object. OV*1x2x4x4If necessary, use the Zoom for precise aiming.* OV = Overview0.237 m1x5Select arrows with the cursor keys or by tapping on the display and adjust with softkeys. Corre-sponding diameter is cal-culated.6Confirm meas-urement.0.237 m0.744 m0.044 m27More results are displayed. CircumferenceCircular areaExit.8
Leica DISTOTM S910 805080 38ENFunctionsArea from Photo1-.--- m21x23Aim perpendicular to the horizontal center line of the ar-ea. This area must be perfectly flat on the vertical plane.OV*1x2x4x4If necessary, use the Zoom for precise aiming.* OV = Overview2.015m9.232m25Select arrows with the cursor keys or by tapping on the display and adjust with softkeys. Corre-sponding area is calculat-ed.Confirm measurement.64.581 m2.015 m13.192 m9.232m27WidthLengthCircumference8Exit.
Leica DISTOTM S910 805080 39ENFunctionsPointdata transmission1P23Aim laser at first point.13.207 m4WiFi data transfer of 3 coordinates x, y, z5Aim at additional points.Leave actual function, go to default operation mode.62xiThis function sends the x, y z coordinates of the measured point. Used in combination with DISTO™ transfer or ??? Plugin.Data transfer works only with WiFi.LevellingiLevel the device to get more accurate measuring data.Do not move device after leveling.For leveling, Smart Base has to be folded out and device needs to be in an inclination range of +/-5°.90°90°Rotate the device two times clock-wise 90°. Follow the instructions on the display.Levelling is finished when OK icon appears on the display.
Leica DISTOTM S910 805080 40ENFunctionsSmart Angle measuring12Initialize device for vertical and hori-zontal val-ues. Details see "Levelling".13Aim laser at point on first wall.425Aim laser at cor-ner.637Aim laser at point on second wall.1.246m5.269m89.56°DD8LevellingiLevel the device to get more accurate measuring data.Do not move device after leveling.For leveling, Smart Base has to be folded out and device needs to be in an inclination range of +/-5°.90°90°Rotate the device two times clock-wise 90°. Follow the instructions on the display.Levelling is finished when OK icon appears on the display.
Leica DISTOTM S910 805080 41ENFunctionsPoint to point function / distance1P12Initialize device for vertical and horizontal values. See "Level-ling".13Aim laser at first target.425Aim laser at second target.13.207m6iLevel the device and further values can be displayed (see "Levelling"!Do not move Smart Base after levelling!-1.697m2.419m35.06°2.995mCheck status line:indicates proper levelingindicates insuffi-cient levelingLevellingiLevel the device to get more accurate measuring data.Do not move device after leveling.For leveling, Smart Base has to be folded out and device needs to be in an inclination range of +/-5°.90°90°Rotate the device two times clock-wise 90°. Follow the instructions on the display.Levelling is finished when OK icon appears on the display.
Leica DISTOTM S910 805080 42ENFunctionsSmart Area measuring12Initialize device for vertical and hori-zontal val-ues. Details see "Lev-elling".13Aim at first target.5.873m41123455Aim at additional points (max. 20)84.675m26LevellingiLevel the device to get more accurate measuring data.Do not move device after leveling.For leveling, Smart Base has to be folded out and device needs to be in an inclination range of +/-5°.90°90°Rotate the device two times clock-wise 90°. Follow the instructions on the display.Levelling is finished when OK icon appears on the display.
Leica DISTOTM S910 805080 43ENFunctionsData capture in DXF-file1P23Aim at first point.4Aim at additional points (max. 30)5Stops DXF capture and saves data.6Leave actual function, go to default opera-tion mode.2xiMax. 20 DXF files can be generated (with 30 meas-uring points/photos each).LevellingiLevel the device to get more accurate measuring data.Do not move device after leveling.For leveling, Smart Base has to be folded out and device needs to be in an inclination range of +/-5°.90°90°Rotate the device two times clock-wise 90°. Follow the instructions on the display.Levelling is finished when OK icon appears on the display.
Leica DISTOTM S910 805080 44ENTechnical Data* favourable conditions are: white and diffuse reflecting target (white painted wall), low background illumination and moderate temperatures.** unfavourable conditions are: targets with lower or higher reflectivity or high background illumination or temperatures at the upper or lower end of the specified temperature range. *** Tolerances apply from 0.05 m to 10 m with a confidence level of 95%. With favourable conditions the tolerance may deteriorate by 0.05 mm/m for distances between 10 m to 30 m, by 0.10 mm/m between 30 m and 100 m and by 0.20 mm/m for distances above 100 m.With unfavourable conditions the tolerance may deterio-rate by 0.10 mm/m for distances between 10 m to 30 m, by 0.20 mm/m between 30 m and 100 m and by 0.30 mm/m for distances above 100 m.**** after user calibration. Additional angle related deviation of +/- 0.01° per degree up to +/-45° in each quadrant. Applies at room temperature. For the whole operating temperature range the maximum deviation increases by +/-0.1°.At a recommended storage tempera-ture of -20°C to +30°C (-4°F to +86°F), batteries containing a 50% to 100% charge can be stored up to 1 year. After this storage period the batteries must be recharged.For accurate indirect results, the use of a tripod is recommended. For accurate tilt measurements a transverse tilt should be avoided. Distance measurement (ISO 163331-1)Accuracy with favourable conditions*± 1.0 mm / 0.04 in ***Accuracy with unfavourable conditions**± 3.0 mm / 0.12 in ***Range with favourable condi-tions*0.05m - 300 m / 0.16 - 984 ftRange with unfavourable condition**0.05m - 150m (0.16 – 492 ft)****Smallest unit displayed 0.1 mm / 1/32 inX-Range Power Technology™yesØ laser pointat distances6 /30 / 60 mm(10 / 50 / 100 m)Tilt measurementMeasuring tolerance to laser beam****-0.1° / +0.2°Measuring tolerance to housing****± 0.1°Range 360°Smart BaseWorking range vertical sensor-40° to 80°Tolerance vertical sensor up to +/- 0.1°Working range horizontal sensor360°Tolerance Horizontal Sensor up to +/- 0.1°Tolerance P2P functionat distances (combination of sensors and distance meas-uring)approx. : +/- 2 mm / 2 m +/- 5 mm / 5 m +/- 10 mm /10 mDevice levellingLevelling range +/- 5°Levelling accuracy +/- 0.05°GeneralLaser class 2Laser type 635 nm, < 1 mWProtection class IP54 (dust- and splash water protected)Autom. laser switch off after 90 sAutom. power switch-off after 180 sBluethooth® Smart Bluethooth v4.0Range of Bluethooth®<10 mWiFi yesRange of WiFi 10 mDimension (H x D x W) 61 x 32 x 164 mm2.4 x 1.3 x 6.5 inWeight 291 g / ... ozTemperature range:-Storage-Operation-Charging-25 to 60 °C-13 to 140 °F-10 to 50 °C14 to 122 °F-10 to 40 °C14 to 104 °FPhotos / ScreenshotsResolution for photos 800 x 600 dpiResolution for screenshots 240 x 400 dpiFile format JPGDownload of gallery USBBattery (Li-Ion)Rated voltage 3.7 VCapacity 2.6 AhMeasurements per battery chargeApprox. 4000Charging time Approx. 4 hOutput voltage 5.0 VCharging current 1 Aii
Leica DISTOTM S910 805080 45ENMessage CodesIf the message Error does not disappear after switching on the device repeatedly, contact the dealer.If the message InFo appears with a number, press the Clear button and observe the following instructions:Care•Clean the device with a damp, soft cloth.•Never immerse the device in water.•Never use aggressive cleaning agents or solvents.FunctionsDistance measuring yesMin/Max measuring yesPermanent measuring yesStake-out yesAddition/Subtraction yesArea yesTriangle area yesVolume yesTrapezium yesPainter function (area with partial measurem.)yesPythagoras 2-point, 3-pointSmart Horizontal Mode / Indirect heightyesHeight-profile measurement yesLevel yesSloped objects yesHeight tracking yesMemory yesBeep yesIlluminated colour display yesPointfinder (Viewscreen) 4x zoom, OVBluetooth® Smart yesPersonalized Favorites yesTimer yesCalculator yesPhoto/Screenshot yesCompass yesGallery with USB download yesDiameter yesWidth yesArea from Photo yesSmart Base yesPointdata transmission yesPoint to point function /distance yesSmart Angle yesSmart Area yesDXF Data capture yesNo. Cause Correction156 Transverse tilt greater than 10°Hold the instrument without any transverse tilt.162 Calibration mistake Make sure, the device is placed on a absolutely hori-zontal and flat surface. Repeat the calibration procedure. If the mistake still occurs, contact your dealer.204 Calculation error Perform measurement again.240 Data transfer error Repeat procedure.252 Temperature too highLet device cool down.253 Temperature too lowWarm device up.255 Received signal too weak, measuring time too longChange target surface (e.g. white paper).256 Received signal too highChange target surface (e.g. white paper).No. Cause Correction258 Measurement outside of measuring rangeCorrect range.260 Laser beam inter-ruptedRepeat measurement.300 Smart Base not folded outFold out Smart Base301 Device was moved, leveling not valid any moreProceed leveling again302 «Point data transmis-sion» is selected, but WiFi is offSwitch on WiFi340 WiFi: Data transfer errorRepeat procedure341 Authentication Error Use correct password
Leica DISTOTM S910 805080 46ENWarrantyWarranty under PROTECT by Leica GeosystemsLifetime Manufacturer's WarrantyWarranty coverage for the entire usage time of the product under PROTECT according to Leica Geosystems International Limited Warranty and PROTECT General Terms & Conditions set out under www.leica-geosys-tems.com/protect. Free of charge repair or replacement of all products or any parts under PROTECT that suffer defects as a result of faults in materials or workmanship.3 Years No CostAdditional services should the product under PROTECT become defective and require servicing under normal conditions of use, as described in the user manual, at no additional charge.To receive the "3 years No Cost" period, the product under PROTECT must be regis-tered at http://myworld.leica-geosys-tems.com within 8 weeks of the purchase date. If the product under PROTECT is not registered, a "2 years No Cost" period applies. Garantie unter PROTECT by Leica GeosystemsLebenslange HerstellergarantieGewährleistungsrechte während der gesa-mten Nutzungszeit des Produkts unter PROTECT gemäß Leica Geosystems' Inter-nationaler Herstellergarantie und den Allge-meinen Geschäftsbedingungen für PROTECT, nachzulesen unter www.leica-geosystems.com/protect. Kostenlose Repa-ratur oder Austausch aller defekter Produkte aufgrund von Material- oder Verarbeitungs-fehlern.3 Jahre keine ZusatzkostenZusätzliche Services, ohne Zusatzkosten, falls beim Produkt unter normaler Benut-zung, wie in der Bedienungsanleitung beschrieben, ein Defekt auftritt und bestimmte Serviceleistungen notwendig werden.Für die "3 Jahre ohne Zusatzkosten" muss das Produkt auf unserer Website http://myworld.leica-geosystems.com binnen acht Wochen nach Kaufdatum regis-triert werden. Für das nicht registrierte Produkte unter PROTECT gilt ein Zeitraum von "2 Jahren ohne Zusatzkosten".Safety InstructionsThe person responsible for the instrument must ensure that all users understand these directions and adhere to them.Areas of responsibilityResponsibilities of the manufacturer of the original equipment: Leica Geosystems AGHeinrich-Wild-StrasseCH-9435 HeerbruggInternet: www.disto.comThe company above is responsible for supplying the product, including the User Manual in a completely safe condition.The company above is not responsible for third party accessories.Responsibilities of the person in charge of the instrument:•To understand the safety instructions on the product and the instructions in the User Manual.•To be familiar with local safety regulations relating to accident prevention.•Always prevent access to the product by unauthorised personnel.
Leica DISTOTM S910 805080 47ENSafety Instructions•Measuring distances•Tilt measurement•Data transfer with Bluetooth® and WIFIProhibited use•Using the product without instruction•Using outside the stated limits•Deactivation of safety systems and removal of explanatory and hazard labels•Opening of the equipment by using tools (screwdrivers, etc.)•Carrying out modification or conversion of the product•Use of accessories from other manufac-turers without express approval•Deliberate dazzling of third parties; also in the dark•Inadequate safeguards at the surveying site (e.g. when measuring on roads, construc-tion sites, etc.)•Deliberate or irresponsible behaviour on scaffolding, when using ladders, when measuring near machines which are running or near parts of machines or instal-lations which are unprotected•Aiming directly in the sunWARNINGWatch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified. Carry out periodic test measurements.Particularly after the instrument has been subject to abnormal use, and before, during and after important measurements.CAUTIONNever attempt to repair the product your-self. In case of damage, contact a local dealer.WARNINGChanges or modifications not expressly approved could void the user’s authority to operate the equipment.Limits of useRefer to section "Technical data".The device is designed for use in areas permanently habitable by humans. Do not use the product in explosion hazardous areas or in aggressive environments.DisposalCAUTIONFlat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations.The product must not be disposed with household waste.Dispose of the product appropriately in accordance with the national regu-lations in force in your country.Adhere to the national and country specific regulations.Product specific treatment and waste management can be downloaded from our homepage.Electromagnetic Compatibility (EMC)WARNINGThe device conforms to the most stringent requirements of the relevant standards and regulations.Yet, the possibility of causing interference in other devices cannot be totally excluded.i
Leica DISTOTM S910 805080 48ENSafety InstructionsFCC statement (applicable in U.S.)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmful interfer-ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:•This device may not cause harmful interfer-ence, and•this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:•This device may not cause interference and•this device must accept any interference, including interference that may cause undesired operation of the device. Déclaration FCC, applicable aux Etats-UnisCe produit a été testé et ses limites ont été jugées conformes à celles prescrites pour les dispositifs numériques de classe B, décrites dans le paragraphe 15 des règles FCC. Ces limites ont pour but de fournir une protec-tion raisonnable contre des interférences nocives dans une installation résidentielle. Les appareils de ce type génèrent, utilisent et peuvent rayonner de hautes fréquences. Ils sont de ce fait susceptibles de perturber la réception radiophonique en cas d'installation non conforme aux instructions.Même en cas de respect des instructions, l'absence d'interférences dans une installa-tion particulière ne peut cependant être garantie. Si cet instrument perturbe la récep-tion radiophonique ou télévisuelle, ce que l'on constate en éteignant puis en rallumant l'instrument, l'utilisateur peut tenter de corriger ces interférences en appliquant les mesures suivantes : •Réorienter ou repositionner l'antenne de réception.•Augmenter la distance entre l'instrument et le récepteur.•Connecter l'instrument à un autre circuit que celui du récepteur.•Consulter le revendeur ou un technicien expérimenté dans le domaine radio/TV.
Leica DISTOTM S910 805080 49ENSafety InstructionsCet appareil est conforme à la section 15 des règlements FCC. Son fonctionnement est soumis aux deux conditions suivantes :•cet appareil ne doit pas causer d'inter-férences nuisibles, et •cet appareil doit accepter toute autre interférence reçue, y compris les inter-férences pouvant entraîner un fonc-tionnement non désiré. Ce dispositif est conforme à la norme RSS-210 d’Industrie Canada. L’utilisation est sujette aux deux conditions suivantes : •ce dispositif ne pas doit pas être la source d’interférences nuisibles, et •ce dispositif doit accepter toutes les inter-férences, y compris les interférences pouvant induire des opérations non souhaitées. Normativa FCC (aplicable en EE UU)Las pruebas efectuadas han puesto de mani-fiesto que este equipo se atiene a los valores límite, determinados en la sección 15 de la normativa FCC, para instrumentos digitales de la clase B. Esto significa que el instrumento puede emplearse en las proximidades de lugares habitados, sin que su radiación resulte molesta. Los equipos de este tipo generan, utilizan y emiten una frecuencia de radio alta y, en caso de no ser instalados conforme a las instrucciones, pueden causar perturbaciones en la recepción radiofónica.En todo caso, no es posible excluir la posibi-lidad de que se produzcan perturbaciones en determinadas instalaciones.Si este equipo causa perturbaciones en la recepción radiofónica o televisiva, lo que puede determinarse al apagar y volver a encender el equipo, el operador puede intentar corregir estas interferencias de la forma siguiente:•cambiando la orientación o la ubicación de la antena receptora.•aumentando la distancia entre el instru-mento y el receptor.•conectando el instrumento a un circuito distinto al del receptor.•asesorándose por el vendedor o algún técnico de radio-televisión.Use of the product with Blue-tooth®WARNINGElectromagnetic radiation can cause distur-bances in other equipment, in installations (e.g. medical ones such as pacemakers or hearing aids) and in aircraft. It can also affect humans and animals.Precautions:Athough this product conforms to the most stringent standards and regulations, the possibility of harm to people and animals cannot totally excluded. •Do not use the product near petrol stations, chemical plants, in areas with a potentially explosive atmosphere and where blasting takes place.•Do not use the product near medical equipment.•Do not use the product in airplanes.•Do not use the product near your body for extended periods.
Leica DISTOTM S910 805080 50ENSafety InstructionsLaser classificationThe device produces visible laser beams, which are emitted from the instrument:It is a Class 2 laser product in accordance with:•IEC60825-1 : 2014 „Radiation safety of laser products“Laser Class 2 products:Do not stare into the laser beam or direct it towards other people unnecessarily. Eye protection is normally afforded by aversion responses including the blink reflex.WARNINGLooking directly into the beam with optical aids (e.g. binoculars, telescopes) can be hazardous.CAUTIONLooking into the laser beam may be hazardous to the eyes.LabellingSubject to change (drawings, descriptions and technical data) without prior notice.Description ValueWavelength 620 - 690 nmMaximum radiant output power for classification 0.95 mWPulse repetition frequency 320 MHzPulse duration > 400 psBeam divergence0.16 x 0.6 mrad

Navigation menu