Leica Geosystems CPD LD5PS Leica DISTO S910 User Manual S910 en

Leica Geosystems AG, CPD Leica DISTO S910 S910 en

15_[Leica DISTO S910] UserMan

Leica DISTOTM S910 805080 1
ENTable of Contents
Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Basic measuring screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
Selection screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
Pointfinder (Viewscreen)- - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Icons on Status bar - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Charging the Li-Ion battery via USB - - - - - - - - - - - - - - - - - - - - - 5
Using the Smart Base - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Using the Smart Base Extension - - - - - - - - - - - - - - - - - - - - - - - 6
Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
Using the Touch Screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Message Codes- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Permanent / Minimum-Maximum measuring - - - - - - - - - - - - - - - 8
Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Pointfinder (Viewscreen)- - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
Screenshot- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
Settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Tilt units - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Distance units- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
Beep ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Digital level ON/OFF- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
De-/Activate keylock - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Switch on with keylock - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Bluetooth® /WIFI - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Calibration of tilt sensor (Tilt Calibration) - - - - - - - - - - - - - - - - 15
Personalized favorites- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Illumination - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Touch Screen ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Date and Time - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
Compass Adjustment - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
Offset - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
Reset - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
Functions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19
Timer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
Calculator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
Adjusting measuring reference - - - - - - - - - - - - - - - - - - - - - - - 21
Memory - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Measuring single distance - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Smart Horizontal Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Level - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
Volume - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
Photo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25
Compass - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
Gallery - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
Triangular area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
Height-profile measurement - - - - - - - - - - - - - - - - - - - - - - - - - 29
Sloped objects - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 30
Height tracking- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 31
Trapezium - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 32
Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 33
Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 34
Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 35
Width - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 36
Diameter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 37
Area from Photo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 38
Pointdata transmission- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 39
Smart Angle measuring - - - - - - - - - - - - - - - - - - - - - - - - - - - - 40
Point to point function / distance- - - - - - - - - - - - - - - - - - - - - - 41
Smart Area measuring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 42
Data capture in DXF-file - - - - - - - - - - - - - - - - - - - - - - - - - - - 43
Technical Data- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 44
Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 45
Care - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 45
Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 46
Safety Instructions- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 46
Areas of responsibility - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 46
Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 47
Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 47
Disposal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 47
Electromagnetic Compatibility (EMC) - - - - - - - - - - - - - - - - - - - 47
FCC statement (applicable in U.S.) - - - - - - - - - - - - - - - - - - - - - 48
Déclaration FCC, applicable aux Etats-Unis - - - - - - - - - - - - - - - 48
Normativa FCC (aplicable en EE UU) - - - - - - - - - - - - - - - - - - - 49
Use of the product with Bluetooth®- - - - - - - - - - - - - - - - - - - - 49
Laser classification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50
Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50
Leica DISTOTM S910 805080 2
ENInstrument Set-up
Introduction
The safety instructions and the user manual should be read
through carefully before the product is used for the first time.
The person responsible for the product must ensure that all
users understand these directions and adhere to them.
The symbols used have the following meanings:
WARNING
Indicates a potentially hazardous situation or an unintended use
which, if not avoided, will result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation or an unintended use
which, if not avoided, may result in minor injury and/or appreciable
material, financial and environmental damage.
Important paragraphs which must be adhered to in practice as
they enable the product to be used in a technically correct and
efficient manner.
i
Overview
Display
On/Measure
Pointfinder
(Viewscreen)
Navigation
Clear / Off
Selection keys
linked to symbols
above
Enter / Equal
Function screen
Add / Subtract
Leica DISTOTM S910 805080 3
ENInstrument Set-up
Basic measuring screen
Status bar
Favorites
Main line
Active function
Tap here to start
ON/DIST in a dis-
tance function
Selection screen
FUNC
Settings
Function /
Settings
Help function
Leica DISTOTM S910 805080 4
ENInstrument Set-up
Pointfinder (Viewscreen)
1x
24.210m
Zoom stage
Favorites
Illumination
adjustment
with navigation
keys left and
right
Active function
Zoom with
navigation keys
up and down
Crosshair
Spread 2 fingers apart to zoom
on the touch screen
Icons on Status bar
Scroll up and down for further results
Battery power
Bluetooth® is switched on
Bluetooth® connection established
Device is not leveled
Offset is activated and subtracts the defined value from measured distance
Offset is activated and adds the defined value from measured distance
WiFi client mode activated
DISTO connected as client to WiFi
Zoom
Device is leveled
DISTO WiFi hotspot activated
Other device connected to DISTO WiFi hotspot
Device is measuring
Measuring reference
Leica DISTOTM S910 805080 5
ENInstrument Set-up
Charging the Li-Ion battery via USB
Charge the battery before using it for the first time. Use the
provided cable to charge the battery.
Plug the small end of the cable into the port of the device, and plug
the end of the charger into an electrical socket. Select the appro-
priate connector for your country. The device cannot be used while
it is charging.
The computer can also be used to charge the device, but this takes
more time. If the device is connected to the computer via USB
cable, you can download or delete the gallery. It is not possible
to upload any data.
When you charge the battery, the following icons show the status:
4
h
Charging Fully charged
CAUTION
Connecting the charger improperly may cause serious damage
to the device. Any damage caused by misuse is not covered by
the warranty. Use only Leica-approved chargers, batteries, and
cables. Unapproved chargers or cables can cause the battery
to explode or damage the device.
If the device is connected to the computer via USB cable, you
can download or delete the gallery. It is not possible to upload
any data.
i
Charge batteries when battery symbol is flashing.
While charging, the device may heat up. This is normal and should
not affect the device’s lifespan or performance. If the battery gets
hotter than 40°C / 104°F, the charger stops.
At a recommended storage temperature of -20°C to +30°C
(-4°F to +86°F), batteries containing a 50% to 100% charge can
be stored up to 1 year. After this storage period the batteries
must be recharged.
To save energy, unplug the charger when not in use.
Leica DISTOTM S910 805080 6
ENInstrument Set-up
Using the Smart Base
Using the Smart Base Extension
Unlock
Lock
Tripod or
Adapter thread
Fold out Smart Base.
Use it as mini tripod.
The Smart Base Extension
supports stable targeting
without tilting.
i
Do not move or tilt the Smartbase during measuring.
We recommend to use a tripod with the Leica FTA360-S
adapter.
Leica DISTOTM S910 805080 7
ENOperations
Operations
Using the Touch Screen
i
Use only fingers to use the touch screen.
Do not allow the touch screen to come into contact with other elec-
trical devices.
Electrostatic discharges can cause the touch screen to malfunction.
Do not allow the touch screen to contact water. The touch screen
may malfunction in humid conditions or when exposed to water.
To avoid damaging the touch screen, do not tap it with anything sharp
or do not apply excessive pressure to it with your fingertips.
Tapping
Tap on the display to open an on-
screen button or to make a selection.
Tapping on the icon in the middle of
the bottom line activates the distance
measurement or triggers the camera.
Dragging
Drag on the display to move to prior or
to next screen in the galerie function.
Pinching
Spread 2 fingers apart to zoom if
pointfinder is activated.
i
Instead of using
the touch
screen, the nor-
mal keypad but-
tons can be
used also.
Leica DISTOTM S910 805080 8
ENOperations
Switching ON/OFF Clear Message Codes
ON
OFF
2 sec
Device is turned
OFF.
i
If no key is
pressed for 180
sec, the device
switches off au-
tomatically.
1x
Undo last action.
2x
Leave actual func-
tion, go to default
operation mode.
If the info icon appears with a
number, observe the instructions in
section "Message Codes".
Example:
Permanent / Minimum-Maximum measuring
1
2 sec
8.532 m
Used to measure room diagonals (maximum val-
ues) or horizontal distance (minimum values)
The minimum and maximum dis-
tance measured is displayed (min,
max.). The last value measured is
displayed in the main line.
min. max.
2
Add / Subtract
7.332 m
1
The next meas-
urement is added
to the previous
one.
2
The next meas-
urement is sub-
tracted from the
previous one.
2x
7.332 m
12.847 m
3
20.179 m
4
This process can be repeated as
required. The same process can
be used for adding or subtracting
areas or volumes.
Leica DISTOTM S910 805080 9
ENOperations
Pointfinder (Viewscreen)
1x
0.00
m
1
OV*
1x
2x
4x
2
1x
0.00m
3
Exit pointfinder
(viewscreen).
4
i
This is a great help for outdoor measuring. The integrated
pointfinder (viewscreen) shows the target on the display.
The device measures in the middle of the cross hair, even if
the laser dot is not visible.
Parallax errors occur when the pointfinder camera is used
on close targets, with the effect that the laser appears dis-
placed in the crosshair. In this case rely on the real laser dot.
* OV = Overview
Screenshot
1x
0.00
m
1
2 sec
Screenshot photo is saved in gallery.
Leica DISTOTM S910 805080 10
ENSettings
Overview
1
2
Tilt units
WiFi / Bluetooth®
Digital level
Keypad lock
Illumination
Favorites
Compass adjustment
Touch screen
Reset
Information
Beep
Tilt calibration
Distance units
Offset
Date and Time
Tilt units
1
2
360.0°
± 180.0°
± 90.0°
0.00 %
0.0 mm/m
0.00 in/ft
Switch between the
following units:
3
4
Confirm setting.
Exit settings.
5
Leica DISTOTM S910 805080 11
ENSettings
Distance units
1
2
0.00 m
0.000 m
0.0000 m
0.0 mm
0.00 ft
0.00 in
0 in 1/32
0'00" 1/32
0.00 m
0.000 m
0.0000 m
0.0 mm
0.00 ft
0
'
00
"
1/32
0
'
00
"
1/16
0
'
00
"
1/8
0
'
00
"
1/4
0.00 in
0 in 1/32
0 in 1/16
0 in 1/8
0 in 1/4
0.000 yd
Art. No. 805080:
3
US-Model Art. No. 808183:
Switch between
the following
units:
4
Confirm setting.
Exit settings.
5
Leica DISTOTM S910 805080 12
ENSettings
Beep ON/OFF
1
ON
2
To switch ON,
repeat procedure.
OFF
Exit settings.
3
Digital level ON/OFF
1
ON
2
To switch ON,
repeat procedure.
OFF
Exit settings.
3
i
The digital level
is displayed in
the status bar.
De-/Activate keylock Switch on with keylock
1
OFF
2
To deactivate, repeat
procedure. The keylock
is active if device is
switched off.
ON
Exit settings.
3
1
Leica DISTOTM S910 805080 13
ENSettings
Bluetooth® /WIFI
1
ON
OFF
O
F
F
2
OFF
Explanation
see info box
below.
Special Settings for
data transfer.
Exit settings.
3
i
Default mode:
Bluetooth®/WIFI is switched on
and black Bluetooth®/WIFI icon
is displayed in status bar.
Blue Bluetooth®/WIFI icon in sta-
tus line is displayed if device is
connected with Blue-
tooth®/WIFI.
i
Special Bluetooth® Settings
Figure Mode: Use this mode if the data needs to be transferred in
figures, e.g. working with spread sheets. Ft/in fractional is converted
into ft/in decimal.
Text Mode: Use this mode if the data needs to be transferred as text,
e.g. working with word processing programs.
App Mode: Use this mode to transfer the data using an App.
Special properties: ENCRYPTED is the default setting. In case of trou-
ble with data transfer, select mode UNENCRYPTED.
Allows the arrow keys to move the cursor on your computer.
sends the value of the main line to the computer.
Allows the arrow keys to move the cursor on your computer.
sends the value of the main line to the computer.
Device is connected. Favorites disappear and two softkeys appear:
Device is connected. Favorites disappear and two softkeys appear:
i
Special WIFI Settings
WiFi: Another device acts as hotspot.
Recommended for GIS applications.
WiFi: DISTO acts as hotspot.
Data transfer unsecured or secured with serial
number as password. Recommended for stand-
ard use.
Leica DISTOTM S910 805080 14
ENSettings
iConnect the device with your smart phone, tablet, laptop,…
The actual measurement is transferred automatically if Blue-
tooth® connection is established. To transfer a result from
the main line, press =. Bluetooth® switches off as soon as the
laser distance meter is switched off.
We provide no warranty for free DISTO™ software and of-
fer no support for it. We accept no liability whatsoever
arising from the use of the free software and we are not
obliged to provide corrections nor to develop upgrades. A
wide range of commercial software can be found on our
homepage. Apps for Android® or Mac iOS can be found in
special internet shops.
For more details, see our homepage.
The efficient and innovative Bluetooth® Smart module
(with the new Bluetooth® standard V4.0) works together
with all Bluetooth® Smart Ready devices. All other Blue-
tooth® devices do not support the energy saving Blue-
tooth® Smart Module, which is integrated in the device.
Bluetooth® data transfer
Leica DISTOTM S910 805080 15
ENSettings
Calibration of tilt sensor (Tilt Calibration)
1
2
3
Place device on absolutely flat surface.
180°
4
180°
5
Turn the device horizontally by 180°
and place it again on absolutely flat
surface.
6
7
Place device on absolutely flat surface.
180°
8
180°
9
Turn the device horizontally by 180°
and place it again on absolutely flat
surface.
10
i
After 2 sec
the device
goes back to
the basic
mode.
Leica DISTOTM S910 805080 16
ENSettings
Personalized favorites
1
Favorite
2
3
Select favorite
function.
4
Press selection
key left or right.
Function is set as
favorite above the
corresponding se-
lection key.
Select your favorite functions for
quick access.
Short cut:
Press 2 sec on a selection-key in
the measuring mode. Select your
favorite function and press again
short on the corresponding se-
lection key.
Illumination
1
1/6
2
1/6
2/6
3/6
4/6
5/6
6/6
3
Select brightness.
4
Confirm setting.
Exit settings.
5
i
To save
power re-
duce bright-
ness if not
necessary.
Touch Screen ON/OFF
1
OFF
2
To deactivate, repeat
procedure.
ON
Exit settings.
3
Leica DISTOTM S910 805080 17
ENSettings
Date and Time
1
2
00 : 00
3
Set time
(hh:mm)
2013-04-08
4
Set date
(yyyy-mm-dd)
Exit settings.
5
Compass Adjustment
iDepending on your geographic location, the angle of declination may vary from
other locations, as the geographic and magnetic poles are aligned. However, if the
reference location is not selected, the difference in declination between the poles
can differ greatly. For best results, select the nearest geographic reference point
using the steps below.
Adjusting the magnetic declination
1
2
CH-Zürich
3
Select the nearest loca-
tion and the device ad-
justs the declination
accordingly.
4
Confirm
Back
Exit settings.
5
Leica DISTOTM S910 805080 18
ENSettings
Offset
1
2
1.012 m
3
Select digit.
1.012 m
4
Adjust digit.
5
Approve
value.
Exit settings.
6
i
An offset adds or subtracts a
specified value automatically to or
from all measurements. This func-
tion allows tolerances to be taken
into account. The offset icon is
displayed.
Reset
1
2
Second confirmation with selection
keys:
3Refuse: Confirm:
Exit settings.
4
i
Reset returns the instrument to
the factory settings. All custom-
ized settings and memories are
lost.
A HARDWARE-RESET is
done by pressing 15 sec on
ON/DIST key.
Leica DISTOTM S910 805080 19
ENFunctions
Overview
Timer
Pointdata transmission
Smart Angle
Memory
Sinlge Distance Measurement
Level
Smart Area measuring function
Point to point function / distance
Photo
Compass
Data capture in DXF-file
Area
Height Tracking
Smart Horizontal Mode
Measuring on sloped objects
Pythagoras (2-point)
Volume
Calculator
Width
Stake out
Diameter
Height-profile Measurement
Trapezium
Gallery
Area from Photo
Adjusting measuring reference
Triangle Area
Pythagoras (3-point)
Leica DISTOTM S910 805080 20
ENFunctions
Timer
1
2
Off
30 sec
10 sec
2 sec
5 sec
3
Select release
time.
4
Confirm setting.
i
The self release
starts if
ON/Measure
key is pressed.
Calculator
1
2
C/CE =
3
Select key on
display.
Confirm every
key.
Use selection keys for
clear or result.
i
The measurement result from the
main line is taken over to the calcula-
tor and can be used for further calcu-
lations.
Ft/in fractions are converted into
ft/in decimal.
To take over a result from the calcu-
lator in the basic mode press DIST
before leaving the calculator function.
Leica DISTOTM S910 805080 21
ENFunctions
Adjusting measuring reference
1
2
3
Distance is measured
from the rear of the de-
vice (standard setting).
Distance is measured
from the front of the de-
vice (lock symbol = per-
manently).
Distance is measured
from Smart Base con-
nection
Distance is measured
from Smart Base base-
plate
i
The orienta-
tion of the
Smart Base is
automatically
detected and
the zero point
is accordingly
adjusted.
4
Confirm setting.
i
If device is
switched off,
reference
goes back to
standard set-
ting (rear of
the device).
Leica DISTOTM S910 805080 22
ENFunctions
Memory
1
2
8.449 m
8
.4
4
9
m
3
Switch between
measurements.
Take over value for
further actions.
Delete memory.
4
Use Up/Down
navigation keys to
show more detailed
results of the speci-
fic measurement.
i
Short cut
Measuring single distance
1
2
Aim active laser at target.
3
8.532 m
4
Target surfaces:
Measuring errors can occur when
measuring to colourless liquids,
glass, styrofoam or semi-permea-
ble surfaces or when aiming at
high gloss surfaces. Against dark
surfaces the measuring time in-
creases.
Smart Horizontal Mode
1
2
Aim laser at
target.
3
z
x
y
40.8 °
x
y
z
5.204 m
0.032 m
4.827 m
4
(up to 360° and a transverse
tilt of ±10°)
Leica DISTOTM S910 805080 23
ENFunctions
Level
1
2
0.3°
90°
0°
3
i
Displays inclinations of 360° with a
transverse inclination of +/- 10°. In-
strument beeps at 0° and 90°. Ideal
for horizontal or vertical adjustments.
Area
1
2
3
Aim laser at first
target point.
4
5
Aim laser at sec-
ond target point.
20.276 m
3.9I0 m
6.228 m
24.352 m
2
First distance
Second distance
Circumference
Area
6
i
The result is shown in the main line and the
measured value above.
Partial Measurements / Painter function:
Press + or - before starting the first measure-
ment. Measure and add or subtract distanc-
es. Finish with =. Measure 2nd length.
Leica DISTOTM S910 805080 24
ENFunctions
Volume
1
2
3
Aim laser at first
target point.
4
5
Aim laser at sec-
ond target point.
6
7
Aim laser at third
target point.
2.431 m
2.338 m
5.744 m
32.653 m
3
First distance
Second distance
Third distance
Volume
8
16.164 m
39.300 m
2
13.430 m
2
9
Use Up/Down
navigation keys to
show more re-
sults.
Ceiling/floor area
Wall areas
Circumference
Leica DISTOTM S910 805080 25
ENFunctions
Photo
1
1x
2
OV*
2x
3
Take photo.
4
Exit.
5
i
Tap on the camera icon in the mid-
dle of the bottom line to take a pho-
to.
For screenshots, press camera key
for 2 sec.
* OV = Overview
Leica DISTOTM S910 805080 26
ENFunctions
Compass
1
2
Calibrate
Compass?
Refuse Confirm
0.0°N
The arrow always
points to true north.
3
Exit.
4
i
At the following places the compass
probably does not work correctly:
• Inside of buildings
• Close to high voltage lines (e.g. on
train platforms)
• Close to magnets, metal objects or
electrical household appliances
i
If an error message occurs,
the device is tilted too much
(>20° over the front / > 10°
sidewise).
Calibration of Compass:
i
The compass
has to be cali-
brated before
every first
measurement
after switching
on the device.
Rotate the device slowly in a figure 8 motion until OK
icon appears on the display.
i
After 2 sec the
device goes
back to the
compass mode.
Leica DISTOTM S910 805080 27
ENFunctions
Gallery
1
1x
2
1x
2013 - 07 - 03_13:25
201
1x
2013 - 07 - 03_13:25
:25
1x
13
-
0
7 -
03_13:25
- 03_
13:
03
- 07
_13
:
25
_13:25
7
1x
2013 - 07 - 03_13:25
3
Exit.
4
i
If the device is connected to the
computer via USB cable, you can
download or delete the gallery. It is
not possible to upload any data.
Leica DISTOTM S910 805080 28
ENFunctions
Triangular area
1
2
3
Aim laser at first
target point.
4
5
Aim laser at sec-
ond target point.
6
7
Aim laser at third
target point.
4.855 m
2
2.425 m
4.129 m
4.248 m
Triangular area
8
First distance
Second distance
Third distance
33.60°
10.802 m
9
Use Up/Down
navigation keys to
show more re-
sults.
Circumference
Angle between first
and second
measurement
Leica DISTOTM S910 805080 29
ENFunctions
Height-profile measurement
1
2
REF
0
Aim at reference point (REF).
3
4
d
h
2.042 m
0.054 m
Horizontal distance to
device
Height difference to
reference point (REF).
6
Exit function.
7
2x
i
Ideal for measuring of height differences to a
reference point. Can be also used to meas-
ure profiles and terrain sections. After meas-
uring the reference point, the horizontal
distance and height is displayed for each fol-
lowing point.
Leica DISTOTM S910 805080 30
ENFunctions
Sloped objects
1
2
3
Aim laser at upper
target point.
4
11.00 °
-3.440 m
30.367 m
5.452 m
P2 distance
Vertical height be-
tween both points
P2 angle
Distance between
both points
6
-4.230 m
39.10 °
7
Use Up/Down
navigation keys to
show more re-
sults.
Horizontal distance
between both points
Included angle be-
tween both points
i
Indirect distance measuring between 2 points with addi-
tional results. Ideal for applications such as length and slope
of roof, height of chimneys,…
It is important, that the instrument is positioned in the
same vertical plane as the 2 measured points. The plane is
defined of the line between the 2 points. This means, that
the device on the tripod is only moved vertically and not
turned horizontally to reach both points.
Leica DISTOTM S910 805080 31
ENFunctions
Height tracking
1
2
P0
Px
Aim laser at lower point.
3
4
x
y
P0
y
29.89 °
6.271 m
-10.55 °
3.475 m
P0
Px
z
6
= Tracking height if device is
turned on tripod
= Tracking angle if device is
turned on tripod
44.80 °
6.271 m
-10.55 °
8.478 m
z
7.160 m
8
Use Up/Down
navigation keys to
show more re-
sults.
i
Heights of buildings or trees without
suitable reflective points can be deter-
mined. At the bottom point, distance
and tilt is measured - which needs a re-
flective laser target. The upper point
can be targeted with the pointfinder /
crosshair and does not need a reflec-
tive laser target as only the inclination is
measured.
Leica DISTOTM S910 805080 32
ENFunctions
Trapezium
1
2
3
Aim laser at upper point.
4
x
x
y
h
y
h
70.80
°
5.790 m
13.459 m
16.440 m
6
20.9
°
78.383 m2
7
Use Up/Down
navigation keys to
show more re-
sults. Trapezium area
Leica DISTOTM S910 805080 33
ENFunctions
Stake out
i
Two different
distances (a
and b) can be
entered to
mark off de-
fined measured
lengths.
1
2
3
a
b
b
a
= b
1
2
3
a
b
b
a
= b
1
2
1.012 m
3
Select digit.
1.012 m
4
Adjust digit.
5
Approve
value "a".
0.625 m
7
Approve value "b"
and start meas-
urement.
8
Move device
slowly along the
stake-out line.
The distance to
the next stake out
point is displayed.
0.240 m
0.625 m
0.240 m is
missing up to
next 0.625 m
distance.
Next stake
out distance
When approaching a stake
out point to less than 0.1 m
the instrument starts to beep.
The function can be stopped
by pressing the CLEAR/OFF
button.
Leica DISTOTM S910 805080 34
ENFunctions
Pythagoras (2-point)
1
2
3
Aim laser at first
target.
4
13.207 m
21.383 m
25.133 m
6
i
The result is shown in the main line.
Pressing the measuring key for 2 sec in the function ac-
tivates automatically Minimum or Maximum measure-
ment.
We recommend to use the pythagoras only for indirect
horizontal measuring.
For height measuring (vertical) it is more precise to use
a function with the inclination measuring.
Leica DISTOTM S910 805080 35
ENFunctions
Pythagoras (3-point)
1
2
3
Aim laser at first
target.
4
5
Aim laser at sec-
ond target.
6
7
Aim laser at
third target.
20.571 m
23.018 m
21.264 m
24.298 m
8
i
The result is shown in the main line.
Pressing the measuring key for 2 sec in the function
activates automatically Minimum or Maximum meas-
urement.
We recommend to use the pythagoras only for indi-
rect horizontal measuring.
For height measuring (vertical) it is more precise to
use a function with inclination measurement.
Leica DISTOTM S910 805080 36
ENFunctions
Width
1
-.--- m
1x
2
16.42m
3It is absolutely
necessary to aim
with the laser per-
pendicular to the
object.
OV*
1x
2x
4x
4
If necessary, use the
Zoom for precise
aiming.
* OV = Overview
1x
16.42 m
5Select arrows with the
cursor keys or by tapping
on the display and adjust
with softkeys. Corre-
sponding width is calcu-
lated.
Confirm
measuremtent.
6
16.42
m
27.539 m
7
Distance to object
Exit.
8
Leica DISTOTM S910 805080 37
ENFunctions
Diameter
1
-.--- m
1x
2
Ø
3
Aim laser perpendicular
to the middle of the
round object.
OV*
1x
2x
4x
4
If necessary, use the
Zoom for precise
aiming.
* OV = Overview
0.237 m
1x
5Select arrows with the
cursor keys or by tapping
on the display and adjust
with softkeys. Corre-
sponding diameter is cal-
culated.
6
Confirm meas-
urement.
0.237 m
0.744 m
0.044 m
2
7
More results are
displayed. Circumference
Circular area
Leica DISTOTM S910 805080 38
ENFunctions
Area from Photo
1
-.--- m
2
1x
2
3Aim perpendicular
to the horizontal
center line of the ar-
ea. This area must be
perfectly flat on the
vertical plane.
OV*
1x
2x
4x
4
If necessary, use the
Zoom for precise
aiming.
* OV = Overview
2.015m
9.232m
2
5Select arrows with the
cursor keys or by tapping
on the display and adjust
with softkeys. Corre-
sponding area is calculat-
ed.
Confirm
measurement.
6
4.581
m
2.015
m
13.192
m
9.232m
2
7
Width
Length
Circumference
8
Exit.
Leica DISTOTM S910 805080 39
ENFunctions
Pointdata transmission
1
P
2
3
Aim laser at first
point.
13.207 m
4
WiFi data transfer of
3 coordinates x, y, z
5Aim at additional
points.
Leave actual function, go to
default operation mode.
6
2x
i
This function sends the x, y z coordinates of the
measured point. Used in combination with DISTO™
transfer or ??? Plugin.
Data transfer works only with WiFi.
Levelling
i
Level the device to get more accurate
measuring data.
Do not move device after leveling.
For leveling, Smart Base has to be
folded out and device needs to be in
an inclination range of +/-5°.
90°
90°
Rotate the device two times clock-
wise 90°. Follow the instructions
on the display.
Levelling is finished when OK icon
appears on the display.
Leica DISTOTM S910 805080 40
ENFunctions
Smart Angle measuring
1
2
Initialize
device for
vertical
and hori-
zontal val-
ues.
Details see
"Levelling".
1
3
Aim laser at point
on first wall.
4
2
5
Aim laser at cor-
ner.
6
3
7
Aim laser at point
on second wall.
1.246
m
5.269
m
89.56°
D
D
8
Levelling
i
Level the device to get more accurate
measuring data.
Do not move device after leveling.
For leveling, Smart Base has to be
folded out and device needs to be in
an inclination range of +/-5°.
90°
90°
Rotate the device two times clock-
wise 90°. Follow the instructions
on the display.
Levelling is finished when OK icon
appears on the display.
Leica DISTOTM S910 805080 41
ENFunctions
Point to point function / distance
1
P1
2
Initialize
device for
vertical and
horizontal
values.
See "Level-
ling".
1
3
Aim laser at first
target.
4
2
5
Aim laser at second
target.
13.207m
6
i
Level the device
and further
values can be
displayed (see
"Levelling"!
Do not move
Smart Base
after levelling!
-1.697
m
2.419
m
35.06°
2.995m
Check status line:
indicates proper
leveling
indicates insuffi-
cient leveling
Levelling
i
Level the device to get more accurate
measuring data.
Do not move device after leveling.
For leveling, Smart Base has to be
folded out and device needs to be in
an inclination range of +/-5°.
90°
90°
Rotate the device two times clock-
wise 90°. Follow the instructions
on the display.
Levelling is finished when OK icon
appears on the display.
Leica DISTOTM S910 805080 42
ENFunctions
Smart Area measuring
1
2
Initialize
device for
vertical
and hori-
zontal val-
ues.
Details
see "Lev-
elling".
1
3
Aim at first target.
5.873m
4
1
1
23
4
5
5
Aim at additional points
(max. 20)
84.675m
2
6
Levelling
i
Level the device to get more accurate
measuring data.
Do not move device after leveling.
For leveling, Smart Base has to be
folded out and device needs to be in
an inclination range of +/-5°.
90°
90°
Rotate the device two times clock-
wise 90°. Follow the instructions
on the display.
Levelling is finished when OK icon
appears on the display.
Leica DISTOTM S910 805080 43
ENFunctions
Data capture in DXF-file
1
P
2
3
Aim at first point.
4
Aim at additional
points (max. 30)
5
Stops DXF
capture and
saves data.
6
Leave actual
function, go to
default opera-
tion mode.
2x
i
Max. 20 DXF files can be
generated (with 30 meas-
uring points/photos each).
Levelling
i
Level the device to get more accurate
measuring data.
Do not move device after leveling.
For leveling, Smart Base has to be
folded out and device needs to be in
an inclination range of +/-5°.
90°
90°
Rotate the device two times clock-
wise 90°. Follow the instructions
on the display.
Levelling is finished when OK icon
appears on the display.
Leica DISTOTM S910 805080 44
ENTechnical Data
* favourable conditions are: white and diffuse reflecting
target (white painted wall), low background illumination and
moderate temperatures.
** unfavourable conditions are: targets with lower or higher
reflectivity or high background illumination or temperatures
at the upper or lower end of the specified temperature
range.
*** Tolerances apply from 0.05 m to 10 m with a confidence
level of 95%. With favourable conditions the tolerance may
deteriorate by 0.05 mm/m for distances between 10 m to
30 m, by 0.10 mm/m between 30 m and 100 m and by 0.20
mm/m for distances above 100 m.
With unfavourable conditions the tolerance may deterio-
rate by 0.10 mm/m for distances between 10 m to 30 m, by
0.20 mm/m between 30 m and 100 m and by 0.30 mm/m
for distances above 100 m.
**** after user calibration. Additional angle related deviation
of +/- 0.01° per degree up to +/-45° in each quadrant.
Applies at room temperature. For the whole operating
temperature range the maximum deviation increases by
+/-0.1°.
At a recommended storage tempera-
ture of -20°C to +30°C (-4°F to
+86°F), batteries containing a 50% to 100%
charge can be stored up to 1 year. After this
storage period the batteries must be
recharged.
For accurate indirect results, the use of
a tripod is recommended. For accurate
tilt measurements a transverse tilt should be
avoided.
Distance measurement (ISO 163331-1)
Accuracy with favourable
conditions*
± 1.0 mm / 0.04 in ***
Accuracy with unfavourable
conditions**
± 3.0 mm / 0.12 in ***
Range with favourable condi-
tions*
0.05m - 300 m /
0.16 - 984 ft
Range with unfavourable
condition**
0.05m - 150m
(0.16 – 492 ft)****
Smallest unit displayed 0.1 mm / 1/32 in
X-Range Power Technology™yes
Ø laser point
at distances
6 /30 / 60 mm
(10 / 50 / 100 m)
Tilt measurement
Measuring tolerance to laser
beam****
-0.1° / +0.2°
Measuring tolerance to
housing****
± 0.1°
Range 360°
Smart Base
Working range vertical
sensor
-40° to 80°
Tolerance vertical sensor up to +/- 0.1°
Working range horizontal
sensor
360°
Tolerance Horizontal Sensor up to +/- 0.1°
Tolerance P2P function
at distances (combination of
sensors and distance meas-
uring)
approx. :
+/- 2 mm / 2 m
+/- 5 mm / 5 m
+/- 10 mm /10 m
Device levelling
Levelling range +/- 5°
Levelling accuracy +/- 0.05°
General
Laser class 2
Laser type 635 nm, < 1 mW
Protection class IP54 (dust- and splash
water protected)
Autom. laser switch off after 90 s
Autom. power switch-off after 180 s
Bluethooth® Smart Bluethooth v4.0
Range of Bluethooth®<10 m
WiFi yes
Range of WiFi 10 m
Dimension (H x D x W) 61 x 32 x 164 mm
2.4 x 1.3 x 6.5 in
Weight 291 g / ... oz
Temperature range:
-Storage
-Operation
-Charging
-25 to 60 °C
-13 to 140 °F
-10 to 50 °C
14 to 122 °F
-10 to 40 °C
14 to 104 °F
Photos / Screenshots
Resolution for photos 800 x 600 dpi
Resolution for screenshots 240 x 400 dpi
File format JPG
Download of gallery USB
Battery (Li-Ion)
Rated voltage 3.7 V
Capacity 2.6 Ah
Measurements per battery
charge
Approx. 4000
Charging time Approx. 4 h
Output voltage 5.0 V
Charging current 1 A
i
i
Leica DISTOTM S910 805080 45
ENMessage Codes
If the message Error does not disappear
after switching on the device repeatedly,
contact the dealer.
If the message InFo appears with a number,
press the Clear button and observe the
following instructions:
Care
•Clean the device with a damp, soft cloth.
•Never immerse the device in water.
•Never use aggressive cleaning agents or
solvents.
Functions
Distance measuring yes
Min/Max measuring yes
Permanent measuring yes
Stake-out yes
Addition/Subtraction yes
Area yes
Triangle area yes
Volume yes
Trapezium yes
Painter function (area with partial
measurem.)
yes
Pythagoras 2-point, 3-point
Smart Horizontal Mode /
Indirect height
yes
Height-profile measurement yes
Level yes
Sloped objects yes
Height tracking yes
Memory yes
Beep yes
Illuminated colour display yes
Pointfinder (Viewscreen) 4x zoom, OV
Bluetooth® Smart yes
Personalized Favorites yes
Timer yes
Calculator yes
Photo/Screenshot yes
Compass yes
Gallery with USB download yes
Diameter yes
Width yes
Area from Photo yes
Smart Base yes
Pointdata transmission yes
Point to point function /distance yes
Smart Angle yes
Smart Area yes
DXF Data capture yes
No. Cause Correction
156 Transverse tilt
greater than 10°
Hold the instrument without
any transverse tilt.
162 Calibration mistake Make sure, the device is
placed on a absolutely hori-
zontal and flat surface.
Repeat the calibration
procedure. If the mistake still
occurs, contact your dealer.
204 Calculation error Perform measurement again.
240 Data transfer error Repeat procedure.
252 Temperature too
high
Let device cool down.
253 Temperature too
low
Warm device up.
255 Received signal too
weak, measuring
time too long
Change target surface (e.g.
white paper).
256 Received signal too
high
Change target surface (e.g.
white paper).
No. Cause Correction
258 Measurement outside
of measuring range
Correct range.
260 Laser beam inter-
rupted
Repeat measurement.
300 Smart Base not folded
out
Fold out Smart Base
301 Device was moved,
leveling not valid any
more
Proceed leveling again
302 «Point data transmis-
sion» is selected, but
WiFi is off
Switch on WiFi
340 WiFi: Data transfer
error
Repeat procedure
341 Authentication Error Use correct password
Leica DISTOTM S910 805080 46
ENWarranty
Warranty under PROTECT by
Leica Geosystems
Lifetime Manufacturer's Warranty
Warranty coverage for the entire usage time
of the product under PROTECT according
to Leica Geosystems International Limited
Warranty and PROTECT General Terms &
Conditions set out under www.leica-geosys-
tems.com/protect. Free of charge repair or
replacement of all products or any parts
under PROTECT that suffer defects as a
result of faults in materials or workmanship.
3 Years No Cost
Additional services should the product under
PROTECT become defective and require
servicing under normal conditions of use, as
described in the user manual, at no additional
charge.
To receive the "3 years No Cost" period, the
product under PROTECT must be regis-
tered at http://myworld.leica-geosys-
tems.com within 8 weeks of the purchase
date. If the product under PROTECT is not
registered, a "2 years No Cost" period
applies.
Garantie unter PROTECT by
Leica Geosystems
Lebenslange Herstellergarantie
Gewährleistungsrechte während der gesa-
mten Nutzungszeit des Produkts unter
PROTECT gemäß Leica Geosystems' Inter-
nationaler Herstellergarantie und den Allge-
meinen Geschäftsbedingungen für
PROTECT, nachzulesen unter www.leica-
geosystems.com/protect. Kostenlose Repa-
ratur oder Austausch aller defekter Produkte
aufgrund von Material- oder Verarbeitungs-
fehlern.
3 Jahre keine Zusatzkosten
Zusätzliche Services, ohne Zusatzkosten,
falls beim Produkt unter normaler Benut-
zung, wie in der Bedienungsanleitung
beschrieben, ein Defekt auftritt und
bestimmte Serviceleistungen notwendig
werden.
Für die "3 Jahre ohne Zusatzkosten" muss das
Produkt auf unserer Website
http://myworld.leica-geosystems.com
binnen acht Wochen nach Kaufdatum regis-
triert werden. Für das nicht registrierte
Produkte unter PROTECT gilt ein Zeitraum
von "2 Jahren ohne Zusatzkosten".
Safety Instructions
The person responsible for the instrument
must ensure that all users understand these
directions and adhere to them.
Areas of responsibility
Responsibilities of the manufacturer
of the original equipment:
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Internet: www.disto.com
The company above is responsible for
supplying the product, including the User
Manual in a completely safe condition.
The company above is not responsible for
third party accessories.
Responsibilities of the person in
charge of the instrument:
•To understand the safety instructions on
the product and the instructions in the
User Manual.
•To be familiar with local safety regulations
relating to accident prevention.
•Always prevent access to the product by
unauthorised personnel.
Leica DISTOTM S910 805080 47
ENSafety Instructions
•Measuring distances
•Tilt measurement
•Data transfer with Bluetooth® and WIFI
Prohibited use
•Using the product without instruction
•Using outside the stated limits
•Deactivation of safety systems and
removal of explanatory and hazard labels
•Opening of the equipment by using tools
(screwdrivers, etc.)
•Carrying out modification or conversion of
the product
•Use of accessories from other manufac-
turers without express approval
•Deliberate dazzling of third parties; also in
the dark
•Inadequate safeguards at the surveying site
(e.g. when measuring on roads, construc-
tion sites, etc.)
•Deliberate or irresponsible behaviour on
scaffolding, when using ladders, when
measuring near machines which are
running or near parts of machines or instal-
lations which are unprotected
•Aiming directly in the sun
WARNING
Watch out for erroneous measurements if
the instrument is defective or if it has been
dropped or has been misused or modified.
Carry out periodic test measurements.
Particularly after the instrument has been
subject to abnormal use, and before, during
and after important measurements.
CAUTION
Never attempt to repair the product your-
self. In case of damage, contact a local dealer.
WARNING
Changes or modifications not expressly
approved could void the user’s authority to
operate the equipment.
Limits of use
Refer to section "Technical data".
The device is designed for use in areas
permanently habitable by humans. Do not
use the product in explosion hazardous areas
or in aggressive environments.
Disposal
CAUTION
Flat batteries must not be disposed of with
household waste. Care for the environment
and take them to the collection points
provided in accordance with national or local
regulations.
The product must not be disposed with
household waste.
Dispose of the product appropriately
in accordance with the national regu-
lations in force in your country.
Adhere to the national and country specific
regulations.
Product specific treatment and waste
management can be downloaded from our
homepage.
Electromagnetic Compatibility
(EMC)
WARNING
The device conforms to the most stringent
requirements of the relevant standards and
regulations.
Yet, the possibility of causing interference in
other devices cannot be totally excluded.
i
Leica DISTOTM S910 805080 48
ENSafety Instructions
FCC statement (applicable in
U.S.)
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reason-
able protection against harmful interference
in a residential installation.This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications.
However, there is no guarantee that interfer-
ence will not occur in a particular installation.
If this equipment does cause harmful interfer-
ence to radio or television reception, which
can be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the
equipment and receiver.
•Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced
radio/TV technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
•This device may not cause harmful interfer-
ence, and
•this device must accept any interference
received, including interference that may
cause undesired operation.
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions:
•This device may not cause interference and
•this device must accept any interference,
including interference that may cause
undesired operation of the device.
Déclaration FCC, applicable aux
Etats-Unis
Ce produit a été testé et ses limites ont été
jugées conformes à celles prescrites pour les
dispositifs numériques de classe B, décrites
dans le paragraphe 15 des règles FCC. Ces
limites ont pour but de fournir une protec-
tion raisonnable contre des interférences
nocives dans une installation résidentielle.
Les appareils de ce type génèrent, utilisent et
peuvent rayonner de hautes fréquences. Ils
sont de ce fait susceptibles de perturber la
réception radiophonique en cas d'installation
non conforme aux instructions.
Même en cas de respect des instructions,
l'absence d'interférences dans une installa-
tion particulière ne peut cependant être
garantie. Si cet instrument perturbe la récep-
tion radiophonique ou télévisuelle, ce que
l'on constate en éteignant puis en rallumant
l'instrument, l'utilisateur peut tenter de
corriger ces interférences en appliquant les
mesures suivantes :
•Réorienter ou repositionner l'antenne de
réception.
•Augmenter la distance entre l'instrument
et le récepteur.
•Connecter l'instrument à un autre circuit
que celui du récepteur.
•Consulter le revendeur ou un technicien
expérimenté dans le domaine radio/TV.
Leica DISTOTM S910 805080 49
ENSafety Instructions
Cet appareil est conforme à la section 15 des
règlements FCC. Son fonctionnement est
soumis aux deux conditions suivantes :
•cet appareil ne doit pas causer d'inter-
férences nuisibles, et
•cet appareil doit accepter toute autre
interférence reçue, y compris les inter-
férences pouvant entraîner un fonc-
tionnement non désiré.
Ce dispositif est conforme à la norme RSS-
210 d’Industrie Canada. L’utilisation est
sujette aux deux conditions suivantes :
•ce dispositif ne pas doit pas être la source
d’interférences nuisibles, et
•ce dispositif doit accepter toutes les inter-
férences, y compris les interférences
pouvant induire des opérations non
souhaitées.
Normativa FCC (aplicable en
EE UU)
Las pruebas efectuadas han puesto de mani-
fiesto que este equipo se atiene a los valores
límite, determinados en la sección 15 de la
normativa FCC, para instrumentos digitales
de la clase B. Esto significa que el instrumento
puede emplearse en las proximidades de
lugares habitados, sin que su radiación
resulte molesta. Los equipos de este tipo
generan, utilizan y emiten una frecuencia de
radio alta y, en caso de no ser instalados
conforme a las instrucciones, pueden causar
perturbaciones en la recepción radiofónica.
En todo caso, no es posible excluir la posibi-
lidad de que se produzcan perturbaciones en
determinadas instalaciones.
Si este equipo causa perturbaciones en la
recepción radiofónica o televisiva, lo que
puede determinarse al apagar y volver a
encender el equipo, el operador puede
intentar corregir estas interferencias de la
forma siguiente:
•cambiando la orientación o la ubicación de
la antena receptora.
•aumentando la distancia entre el instru-
mento y el receptor.
•conectando el instrumento a un circuito
distinto al del receptor.
•asesorándose por el vendedor o algún
técnico de radio-televisión.
Use of the product with Blue-
tooth®
WARNING
Electromagnetic radiation can cause distur-
bances in other equipment, in installations
(e.g. medical ones such as pacemakers or
hearing aids) and in aircraft. It can also affect
humans and animals.
Precautions:
Athough this product conforms to the most
stringent standards and regulations, the
possibility of harm to people and animals
cannot totally excluded.
•Do not use the product near petrol
stations, chemical plants, in areas with a
potentially explosive atmosphere and
where blasting takes place.
•Do not use the product near medical
equipment.
•Do not use the product in airplanes.
•Do not use the product near your body for
extended periods.
Leica DISTOTM S910 805080 50
ENSafety Instructions
Laser classification
The device produces visible laser beams,
which are emitted from the instrument:
It is a Class 2 laser product in accordance
with:
•IEC60825-1 : 2014 „Radiation safety of
laser products“
Laser Class 2 products:
Do not stare into the laser beam or direct it
towards other people unnecessarily. Eye
protection is normally afforded by aversion
responses including the blink reflex.
WARNING
Looking directly into the beam with optical
aids (e.g. binoculars, telescopes) can be
hazardous.
CAUTION
Looking into the laser beam may be
hazardous to the eyes.
Labelling
Subject to change (drawings, descriptions
and technical data) without prior notice.
Description Value
Wavelength 620 - 690 nm
Maximum radiant output
power for classification 0.95 mW
Pulse repetition frequency 320 MHz
Pulse duration > 400 ps
Beam divergence
0.16 x 0.6 mrad

Navigation menu