Lelux Electronics 639S VISITOR CHIME AND WATCH DOG/ALARM User Manual 639R English manual

Download:
Mirror Download [FCC.gov]
Document ID	1175338
Application ID	yUwQVl4/SQM1b5ar7MHvyg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.87kB (823326 bits)
Date Submitted	2009-09-25 00:00:00
Date Available	2009-09-25 00:00:00
Creation Date	2009-09-17 14:01:29
Producing Software	Adobe PDF library 7.77
Document Lastmod	2009-09-17 14:01:30
Document Title	639R English manual
Document Creator	Adobe Illustrator CS2

1. Install 8 AA size alkaline batteries (not included), this is a back-up battery,
in case of AC power failure. This battery will keep the unit working (Fig.3)
INTRODUCTION
INSTALLATION
HomeSafe’s unique microwave detection system concentrates on the
protected area of your selection. Whenever the unit set at ARMED, the
system will standby protected area. Once movement has been detected, will
sound very loud bark /alarm/door chime sound.
The main unit built-in microwave detect sensor can penetrate through
wood, plastic, glass, cement etc (Fig.1), can’t penetrate through detect:1.
Metal objects, 2. Objects containing metals, 3. Other electric objects and ultra
– thick barriers etc.( Fig.2 )
IMPORTANT SAFETY TIPS
1. Do not install the system where it will be exposed to direct sunlight or
rain( for indoor use only).
2. The system sound is very loud, never put the unit close to your ear.
3. The unit should be away from heat sources such as radiators, heating
ducts and stoves.
4. If the system goes off at random, it is might be located too close to a heat
source, changing the location or direction of the unit can remedy this.
5. The system can provide valuable protection for your home and guarantee
complete protection against burglary or robbery therefore, we will not be
responsible for any loss or damages which could occur.
DESCRIPTION OF COMPONENTS
AA
AA
(Fig.7)
SETTING
(Fig.1)
2. Plug the AC adaptor to the DC 12V socket. (Fig.4)
(Fig.2)
Put the main unit on the table of private area or on the surface of any objects,
fix the main unit position with its detecting side (side with battery cover) facing
the burglarproof direction to be detected. Within detected side’s angle range ≤
150˚, try to avoid :
or
Metal Do
AA
AA
OPERATION
(Fig.3)
AA
AA
Metal Do
DC 12V
or
(Fig.4)
Fig.A
( Wrong )
Fig.B
( Right )
3. For wall mount-If required
Choose a suitable location, 0.8 - 1.5 meters away from floor, drill holes
and install anchors and fix the bracket by screws, Place the main unit into
the bracket and slide it down to secure in place (Fig.5).
FEATURES
1. Microwave Sensor detect motion activates sound bark/chime/alarm
2. Adjustable Detect Sensitivity, detect range 0~7meters
3. Detect angle about 150 degrees
4. Sound adjustable volume, sound power up to 5W
6. Bark /Chime/alarm switch
7. RF Remote Control for ARM/DISARM/PANIC
8. AC Adaptor Operation( Included) with AA Size Batteries X8 Backup (Not
Included)
9. Compatible with additional total 16 wireless sensor accessories to
expanding the system
size:100X175mm
p/n:610-63900-001R
white paper print black words
0.8~1.5M
Fig.C
( Wrong )
Fig.D
( Right )
(Fig.6)
(Fig.5)
TO TEST THE DETECTION AREA
After selecting a location for installation of the unit, turn on power switch
and adjusting volume for you desired, turn sound select switch in CHIME,
2. TRIGGER
In ARM mode system detected motion or received wireless sensor
trigger signal in the protected area, will sound for you select:
a. BARK:
1 short bark for detect once trigger of 5 seconds
3 short bark for detect twice trigger of 5 seconds
10 seconds bark for detect thrice trigger of 5 seconds or receive wireless
sensor trigger
b. CHIME:
Detect trigger or receive wireless sensor trigger will sound “DING
DONG, DING DONG”
c. ALARM:
3 seconds alarm for detect once trigger of 5 seconds
6 seconds alarm for detect twice trigger of 5 seconds
20 seconds alarm for detect thrice trigger of 5 seconds or receive
wireless sensor trigger
1.Battery installation and replacement (Battery CR2032)
a. Remove the battery compartment cover by sliding it in the direction of the
arrow.
b. Install (or Replace) with new batteries of the same type.
Make sure the polarity (+ or -) of the batteries match the polarity marks
inside the unit. As shown below (Fig.1).
c. Replace battery cover.
2. Learn ID code to main unit
The wireless remote control included in the package of this system are
pre-programmed with the LEARN ID CODE. The whole unit is ready for
use after installation . When re-programming the LEARN code operation,
see main unit manual LEARN ID CODE FUNCTION.
3. operation
• If radio-linked remote control operation range become shortened, replace
the batteries according to "BATTERY INSTALLATION AND REPLACEMENT".
• The battery life should be about six months under normal use, so replace
battery at least every 6 months.
• Effective range (open space).
PANIC
ARM
4. PANIC FUNCTION
press "PANIC" button of remote control, the unit will sound alarm 20
seconds .
BATTERY LOW INDICATOR
When main unit the battery is running low or not install battery, the
power/battery low LED will from green change to amber to indicate the low
battery.
NOTE: Change to a new battery immediately, otherwise it may appear the
false trigger alarm.
(Fig. 2)
ARM
WARNING:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions;
(1)this device may not cause interference, and
(2)this device must accept any interference received, including interference that
may cause undesired operation of the device.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
POWER/
BATT. LOW
ARM
OWNER'S MANUAL
610-6390X-000R
DISARM
about 20 meters
POWER/
BATT. LOW
3 TO DISARM THE SYSTEM
press "DISARM" button of remote control unit or press ARM/DISARM
button once to DISARM main unit.
VISITOR CHIME AND
WATCH DOG/ALARM
(Fig.1)
DISARM
7 9
1. BARK / CHIME /ALARM switch
For select differ sound
2. POWER switch/volume adjusting button
For control power and volume
3. Range adjusting button
For adjusting detect range
4. Learn ID code function:
For learn wireless sensor or remote control ID code:
All the Expanding Wireless Sensor and remote control attached with the
package of this system are all completed done the LEARN CODE. The
whole units are standby for use after installation directly.
If You add extra purchased wireless Motion Detector sensor (615PR,
616PR) or wireless Door/Window sensor (600WR, 218WR) or wireless
doorbell push button (623T9) and remote control (200R, 500R) to the
system, but it is required to learn the sensor and remote control unit to the
main unit, or wireless sensor and remote control attached with the package
of this system not function, please re-learn the sensor and remote control ID
code to the main unit, the learning code can only be operated during disarm
mode. Follow these steps:
a. Press and hold LEARN button 2 seconds you will hear one beep tone
then un-pressed the button, the unit now ready to receive learn code
signal from transmitter.
b. Trigger wireless motion detector sensor (swing at sensor lens by hand will
trigger) for motion detector sensor learn ID code or trigger door/window
sensor (open/close the magnetic switch will trigger) for door/window
sensor learn ID code or press the push button for doorbell push button
learn ID code or press any key of remote control for remote control learn
ID code, you will hear two long beep tone confirm learn code successfully
(When learn code unsuccessful You will hear four short beep tone).
Please relearn again.
1. TO ARM THE SYSTEM
a. Turn on power switch(the POWER/BATT.LOW LED will light up green)
and adjusting volume and select sound for you desired, press ARM
button of remote control or press ARM/DISARM button once of main
unit, will sound 1 short bark for switch in BARK or DING DONG for
CHIME or BEEP for switch in ALARM, the ARM LED will light up.
b. There will be a further single beep after 60 seconds, the unit is now set
at ARM.
WIRELESS REMOTE CONTROL (MODEL: 500R)
ARM
then press ARM/DISARM button once of main unit or press ARM button of
remote control , you will hear “DING DONG”, wait for 60 seconds for
“WARM-UP” (you will hear a long beep sound). Then you try walking in front
of the unit. The unit will detect motion and the chime will sound. If you walk
beyond the detection range the chime will not sound. To test the detection
range try various and range adjust button for best coverage.
PANIC
1. Bark/chime/alarm
switch
2. ARM/DISARM button
3. DC Jack
4. ARM indicator LED
5. POWER/Battery
low LED
6. Power off / volume
adjusting button
7. Detect range
adjusting button
8. Learn ID code button
9. Battery Cover
AA
AA
4. Detect angle range: Through wall: about Back:0~5 meter (Fig.6) ; Open
space :Obverse, right, left: 0~3 meter;Back:0~7 meter (Fig.7).SYSTEM

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1.1-111
Format                          : application/pdf
Title                           : 639R English  manual
Creator Tool                    : Adobe Illustrator CS2
Create Date                     : 2009:09:17 14:01:29+08:00
Modify Date                     : 2009:09:17 14:01:30+08:00
Metadata Date                   : 2009:09:17 14:01:30+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 68
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 7843 bytes, use -b option to extract)
Document ID                     : uuid:F1C067524FA3DE11B001F64DB50290DF
Instance ID                     : uuid:7d34a538-92e4-4a90-acd8-1fd4d95e1441
Derived From Instance ID        : uuid:F0C067524FA3DE11B001F64DB50290DF
Derived From Document ID        : uuid:EFC067524FA3DE11B001F64DB50290DF
Producer                        : Adobe PDF library 7.77
Page Count                      : 1
Creator                         : Adobe Illustrator CS2

EXIF Metadata provided by EXIF.tools