Lelux Electronics LELUXT018R WIRELESS SECURITY ALARM SYSTEM User Manual T018 SYSTEM

Download:
Mirror Download [FCC.gov]
Document ID	738148
Application ID	49y6VHx97DVeNPLKgiX2pQ==
Document Description	User Manual Part 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	272.35kB (3404377 bits)
Date Submitted	2006-12-13 00:00:00
Date Available	2006-12-13 00:00:00
Creation Date	2006-12-13 13:07:44
Producing Software	Adobe PDF library 7.77
Document Lastmod	2006-12-13 13:07:52
Document Title	T018 SYSTEM(出版)
Document Creator	Adobe Illustrator CS2

OPTIONAL WIRELESS ACCESSORIES
BATTERY LOW INDICATOR
MODEL 218WR (Wireless Slim Door/Window Sensor)
When battery goes low, the LED will light on 3 seconds and off 1 second, change 2 new CR2032 batteries immediately, or
the sensor might not detect properly.
INSTALLATION
1. Remove the screw from the battery compartment cover.
2. Install 2 “CR2032” batteries (included) on the battery box, ensure the polarity is correct.
3. Replace the battery cover and screw.
4. Mount the magnetic door/window sensor
Choose a suitable location, stick the main unit to the door/window frames by attached double – side tape. Then stick
the magnetic unit (smaller unit) to the door/window by attached double-side tape and make sure to align the “ ”mark
to right “ ”mark on the main unit and “ ” facing “ ” at no more than 1/4” apart as shown below. (Fig.1)
MODEL 600WR (Wireless Door/Window Sensor with Alarm)
INSTALLATION
1. Remove the screw from the battery compartment cover. (Fig.1)
ALARM
ON
OFF
(Fig.1a)
(Fig.1b)
(Fig.2)
(Fig.1)
2. Install an alkaline 9V battery.
3. Replace the battery cover and screw.
4. Mount the magnetic door/window sensorChoose a suitable location, then use the template provided to mark location, drill holes and install anchors and screws.
Place the unit over the screws and slide it down to secure in place. (Fig.2)
5． Mount the magnetic wired piece to the door or window frame and another single piece to the door/window by using the
double-side tapes (included) and aligned the 2 sensor pieces to be flushed and “
” facing “
” at no more than1/4”
apart as shown in. (Fig.3)
5.External Magnetic sensor terminal
You can additionally wire magnetic sensor to expanding you desired detection area.
a.Remove the screw from the battery compartment cover.
b.Remove the screw from terminal and take out connected wire. (Fig.2)
(Fig.3)
(Fig.2)
c.Measure the length of wire needed to connect the sensor to the transmitter, then cut the wire to the correct length.
Strip about 1/2 inch of insulation from the wire ends, and twist the wires together.
d.Connect the sensor switch on door to the main terminal post using the wire you just cut. (There is no polarity need to
be taken care of, any terminal will be fine, as long as the wires from a loop)
e.Connect another sensor switch screw to another switch terminal post by using the parallel another wire as shown
below. (Fig.3)
f.If you connect more than one sensor to the main unit, connect them in series as shown below. (Fig.4)
(Fig.3)
(Fig.4)
6. If you connect more than one sensor to the main unit, connect them in series as shown below. (Fig.4)
NOTE: After select a location, you should test the sensor transmitting range before mount it permanently, turn local alarm
switch to OFF, turn the CHIME switch to ON of main unit, then open/close the magnetic switch of door/window sensor to
trigger, you will hear the main unit sounds “DING DONG” chime if signal is received successfully, if not, draw out mini
retractable antenna or change location as required.
LEARNING CODE TO MAIN UNIT
(Fig.4)
NOTE: After select a location, you should test the sensor transmitting range before mount it permanently, turn the CHIME
switch to ON of main unit, then open/close the magnetic switch of door/window sensor to trigger, you will hear the main
unit sounds “DING DONG” chime if signal is received successfully, if not, draw out mini retractable antenna or change
location as required.
LEARNING CODE TO MAIN UNIT
The wireless door/window sensor with the package of this system are completed done the LEARN CODE. The whole units
are standby for use after installation directly. When relearn code operation see main unit manual.
OPERATION
The wireless door/window sensor with the package of this system are completed done the LEARN CODE. The whole units
are standby for use after installation directly. When relearn code operation see main unit manual.
OPERATION
After 60 seconds installed 9V battery, the unit will into standby mode. Once the door/window opened or vibration detected,
the unit will output wireless radio signal and LED will flash, then sound alarm 3 seconds, you can turn alarm switch select
on or off.
BATTERY LOW INDICATOR
When 9V battery goes low, the LED will light on 3 seconds and off 1 second, change a new alkaline 9V battery immediately,
or the sensor might not detect properly.
After 60 seconds installed battery, the unit will into standby mode. Once the door/window opened or vibration detected, the
unit will output wireless radio signal and LED will flash.
-7-
-8-
MODEL 615PR (Wireless Motion Detector Sensor)
ADJUST DETECT DISTANCE
INSTALLATION
To increase sensitivity turn the sensitivity control toward MAX. to decrease sensitivity, turn the sensitivity control toward
MIN(Fig.2). However, too high sensitivity may result in false triggering, please note.
1. Remove the screw from the battery compartment cover. (Fig.1 ）
MIN
MAX
(Fig.2)
1.5~2M
ADJUST DETECT ANGLE
1.5~2M
(Fig.3)
(Fig.2)
(Fig.1)
(Fig.3)
2. Install an alkaline 9V battery.
3. Replace the battery cover and screw.
4. Mount the wireless motion detector sensorChoose a suitable location, 5 - 6 feet (1.5 - 2.0 meters) away from floor, then use the swivel wall mount bracket template
provided to mark location, drill holes and install anchors and fix the bracket by screws, Place the main unit into the
bracket and slide it down to secure in place (Fig 2). You can adjust bracket to obtain the best coverage of the intended
protected area. (Fig 3)
LEARNING CODE TO MAIN UNIT
The wireless motion detector sensor with the package of this system are completed done the LEARN CODE. The whole
units are standby for use after installed directly. When relearn code operation see main unit manual.
WALK TESTING MOTION DETECTOR SENSOR
After select a location, you should test the sensor transmitting range before mount it permanently, press HOME button of
main unit, ofter 60 seconds ,then swing at sensor lens by hand, you will hear the main unit sounds “DING DONG” chime
if signal is received successfully, if not, change location as required.
You can test the sensor detection area. Temporarily place the detector at the mounting location and the chime sound will
be heard from the main unit. If you walk beyond the sensor detection area, then there will not be a chime sound, by
adjusting the sensor direction, or the installation location, you can get you desired detection area coverage.
The motion detector max detect angle is up to 150 degree, you can adjust slide window of lens left and right side to select
the angle you need. (Fig.3)
LEARNING CODE TO MAIN UNIT
The motion detector sensor is compatible with T015, T016, T018 main unit, must learn code to main unit then use, learn
code operation see main unit manual.
WALK TESTING MOTION DETECTOR SENSOR
After select a location, you should test the sensor transmitting range before mount it permanently, turn the CHIME switch
to ON of T015, T016 main unit or press HOME button of T018 main unit, after 60 seconds then swing at sensor lens by
hand, you will hear the main unit sounds “DING DONG” chime if signal is received successfully, if not, change another
location to test.
You can then test the sensor detection area. Temporarily place the detector at the mounting location and the chime sound
will be heard from the main unit. If you walk beyond the sensor detection area, and there will not be a chime sound, by
adjusting the sensor direction, or the installation location, you can get you desired detection area coverage.
BATTERY LOW INDICATOR
When batteries goes low, the LED will light on 3 seconds and off 1 second, change 3 AA size new alkaline batteries immediately, or the sensor might not detect properly.
MODEL 300R (Wireless Remote Control)
BATTERY LOW INDICATOR
When 9V battery goes low, the LED will light on 3 seconds and off 1 second, change a new alkaline 9V battery immediately, or the sensor might not detect properly.
MODEL 616PR (Wireless Motion Detector Sensor)
1. Batteries install and replacement
(Battery Type-LR44X3 or Similar)
a. Remove the battery compartment cover by screw driver and sliding open the battery Cover.
b. Replace with new batteries of the same type.
Make sure the polarity (+ or -) of the batteries match the polarity marks inside the unit. As shown below. (Fig.1)
c. Replace battery cover
INSTALLATION
1. Remove the screw from the battery compartment cover.
2. Install 3 “AA” alkaline batteries (not included) on the battery box, ensure the
polarity is correct.
3. Replace the battery cover and screw.
4. Mount the wireless motion detector sensorChoose a suitable location, 5 - 6 feet (1.5 - 2.0 meters) away from floor, then use
the swivel wall mount bracket template provided to mark location, drill holes and
install anchors and fixture the bracket by screws, Place the main unit into the
bracket and slide it down to secure in place. You can adjust bracket to obtain the
best coverage of the intended protected area.(Fig.1)
(Fig.1)
LEARNING CODE TO MAIN UNIT
1.5~2M
(Fig.1)
-9-
The wireless remote control with the package of this system are completed done the LEARN CODE. The whole units are
standby for use after installed directly. When relearn code operation see main unit manual.
Notes for remote operation
● If radio linked remote control operation range becomes shorten, replace the batteries according to "BATTERIES
REPLACEMENT".
● The battery life should be about six months under normal use, so replace battery at least every 1 year. Effective range.
(Fig. 2)
- 10 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:ccd6ffdf-9b2c-4fe5-a0f5-918ef7987873
Modify Date                     : 2006:12:13 13:07:52-08:00
Create Date                     : 2006:12:13 13:07:44-08:00
Metadata Date                   : 2006:12:13 13:07:52-08:00
Document ID                     : uuid:d6d22bf1-6124-4e49-ad83-0852baf6f874
Format                          : application/pdf
Title                           : T018 SYSTEM(出版)
Creator                         : Adobe Illustrator CS2
Producer                        : Adobe PDF library 7.77

EXIF Metadata provided by EXIF.tools