Lenovo B580 Hmm En User Manual Hardware Maintenance Laptop (Lenovo) Type 4377

2012-10-22

User Manual: Lenovo B580 Hmm En Hardware Maintenance Manual - Lenovo B580 B580 Laptop (Lenovo) - Type 4377

Open the PDF directly: View PDF .
Page Count: 104

Download
Open PDF In Browser	View PDF

Hardware Maintenance Manual

Lenovo B580

Note: Before using this information and the product it supports, be sure to read the general information
under Appendix A “Notices” on page 95.

Second Edition (October 2012)
© Copyright Lenovo 2012.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration
“GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

Contents
About this manual. . . . . . . . . . .

iii

Chapter 1. Safety information . . . . . . 1
General safety . . . . . . . . . . . . . . .
Electrical safety . . . . . . . . . . . . . .
Safety inspection guide . . . . . . . . . . .
Handling devices that are sensitive to electrostatic
discharge. . . . . . . . . . . . . . . . .
Grounding requirements . . . . . . . . . . .
Safety notices (multilingual translations) . . . . .
Laser compliance statement (multilingual
translations) . . . . . . . . . . . . . . . .

Chapter 2. Important service
information . . . . . . . . . . . . . .
Strategy for replacing FRUs . . . . . . .
Strategy for replacing a hard disk drive .
Important notice for replacing a system
board . . . . . . . . . . . . . .
Important information about replacing RoHS
compliant FRUs . . . . . . . . . . . .

.
.
.

1
2
3

.
.
.

3
4
4
19

. .
. .

27
28

. .

Chapter 3. General checkout . . . . .

What to do first . . . . . . . .
Power system checkout . . . . .
Checking the ac power adapter
Checking operational charging
Checking the battery pack . .

.
.
.
.
.

29
30
30
31
31

Chapter 4. Related service
information . . . . . . . . . . . . . .

Recovering the computer settings
Passwords . . . . . . . . .
Power-on password . . . .
Supervisor password . . .
Power management . . . . .
Screen blank mode . . . .
Sleep mode . . . . . . .
Hibernation mode . . . .

.
.
.
.
.
.
.
.

.
.
.
.
.

.
.
.
.
.
.
.
.

.
.
.
.
.

.
.
.
.
.
.
.
.

.
.
.
.
.

.
.
.
.
.
.
.
.

.
.
.
.
.

.
.
.
.
.
.
.
.

33
34
34
34
34
34
34
35

Chapter 5. Lenovo B580 . . . . . . . .

Specifications . . . . . . . . . . . . . . .
Status indicators . . . . . . . . . . . . . .
Fn key combinations . . . . . . . . . . . .

37
38
39

Chapter 6. FRU replacement
notices . . . . . . . . . . . . . . . .

Screw notices . . . . . . . . . . . . . . .

.
.
.
.
.
.
.
.

.
.
.
.
.

.
.
.
.
.
.
.
.

Chapter 7. Removing and replacing a
FRU . . . . . . . . . . . . . . . . . .
General guidelines . . . . . . . . . . .
1010 Battery pack . . . . . . . . . . .
1020 Bottom slot cover . . . . . . . . .
1030 Optical drive . . . . . . . . . . .
1040 Memory modules . . . . . . . . .
1050 Hard disk drive assembly . . . . . .
1060 PCI Express Mini Card for wireless LAN
1070 mSATA solid-state drive . . . . . . .
1080 Backup battery . . . . . . . . . .
1090 Keyboard . . . . . . . . . . . .
1100 Keyboard bezel . . . . . . . . . .
1110 Fingerprint board and LED board . . .
1120 Power board and touch pad bracket . .
1130 Microphone assembly . . . . . . .
1140 I/O board . . . . . . . . . . . .
1150 System board assembly and USB board
1160 DC-in connector . . . . . . . . . .
1170 Thermal module . . . . . . . . . .
1180 CPU . . . . . . . . . . . . . .
1190 LCD unit . . . . . . . . . . . . .
1200 Speaker assembly . . . . . . . . .
1210 Base cover . . . . . . . . . . . .
2010 LCD front bezel . . . . . . . . . .
2020 Integrated camera . . . . . . . . .
2030 LCD panel, LCD cable, and hinges . .
2040 Antenna assembly and LCD rear cover .

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

43
44
44
45
46
47
49
51
52
53
55
58
59
60
61
62
65
66
68
69
71
72
73
74
75
77

Chapter 8. Locations . . . . . . . . .

Front and right-side view. . . . . . . . . . .
Bottom and left-side view . . . . . . . . . .

79
80

Chapter 9. Parts list . . . . . . . . . .

Overall . . . . . .
LCD FRUs . . . .
Keyboard . . . . .
Miscellaneous parts
ac power adapters .
Power cords . . .

.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.

82
85
87
89
90
91

Appendix A. Notices . . . . . . . . . .

Electronic emissions notices . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . .

96
96

Hardware Maintenance Manual

About this manual
This manual provides service and reference information for the following Lenovo® products.
Machine

Machine type (MT)

Lenovo B580

4377, 20144

Use this manual to troubleshoot problems.
The manual is divided into the following sections:
• The common sections provide general information, guidelines, and safety information required for
servicing computers.
• The product-specific section includes service, reference, and product-specific parts information.

Important:
• This manual is intended only for trained service technicians who are familiar with Lenovo products. Use
this manual to troubleshoot problems effectively.
• Before servicing a Lenovo product, be sure to read all the information under Chapter 1 “Safety
information” on page 1 and Chapter 2 “Important service information” on page 27.

iii

Hardware Maintenance Manual

Chapter 1. Safety information
This chapter presents following safety information that you need to be familiar with before you service a
Lenovo Notebook.
• “General safety” on page 1
• “Electrical safety” on page 2
• “Safety inspection guide” on page 3
• “Handling devices that are sensitive to electrostatic discharge” on page 3
• “Grounding requirements” on page 4
• “Safety notices (multilingual translations)” on page 4
• “Laser compliance statement (multilingual translations)” on page 19

General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing
the machine.
• Keep your toolcase away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing, because metal
objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device
that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.

Electrical safety
Observe the following rules when working on electrical equipment.
Important:
Use only approved tools and test equipment. Some hand tools have handles covered with a soft material
that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to
decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring
high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Similar units to listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
2

Hardware Maintenance Manual

– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.

Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service technicians
from injury. This guide addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning
of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo
alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
Chapter 1. Safety information

2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.

Safety notices (multilingual translations)
The safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese

DANGER

DANGER
4

Hardware Maintenance Manual

DANGER

Chapter 1. Safety information

DANGER

Hardware Maintenance Manual

Chapter 1. Safety information

PERIGO

Hardware Maintenance Manual

PERIGO

DANGER

Chapter 1. Safety information

DANGER

VORSICHT

Hardware Maintenance Manual

VORSICHT

Chapter 1. Safety information

VORSICHT

Hardware Maintenance Manual

Chapter 1. Safety information

Hardware Maintenance Manual

Chapter 1. Safety information

Hardware Maintenance Manual

Chapter 1. Safety information

Hardware Maintenance Manual

Laser compliance statement (multilingual translations)
The laser compliance statements in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese

Chapter 1. Safety information

Hardware Maintenance Manual

Chapter 1. Safety information

Hardware Maintenance Manual

Chapter 1. Safety information

Hardware Maintenance Manual

Chapter 1. Safety information

Hardware Maintenance Manual

Chapter 2. Important service information
This chapter presents the following important service information that applies to all machine types supported
by this manual:
• “Strategy for replacing FRUs” on page 27
– “Strategy for replacing a hard disk drive” on page 28
– “Important notice for replacing a system board” on page 28
• “Important information about replacing RoHS compliant FRUs” on page 28
Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are available
at http://www.lenovo.com/support.

Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs
listed in this manual.
After a system board is replaced, ensure that the latest BIOS is installed to the system board before
completing the service action.
To download software fixes, drivers, and BIOS, do the following:
1. Go to http://www.lenovo.com/support.
2. Click Download Drivers & Software. The Web site offers three options to begin your search:
• Search by product number
• Search through the product auto-detect function
• Search by product category
3. Follow the directions on the screen and install the necessary software.
4. Restart the computer.
Notes: If you need to improve the computer performance, you also could download and install the latest
BIOS utility from the Support Web site.
• Do not try to update the BIOS settings for any computer unless you have been trained and certified. An
untrained person runs the risk of damaging the computer.
• Before installing the latest utility, make sure that the battery is fully charged and an ac power adapter is
connected.
• Do not turn off or put your computer into sleep or hibernation until the update has been completed.
Otherwise, the system board might be damaged.
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:
• If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall
the original FRU before you continue.
• Some computers have both a processor board and a system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.
© Copyright Lenovo 2012

• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change.
Replace only the FRU that changed the symptoms.

Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive (HDD). This will cause all customer data
on the hard disk to be lost. Be sure that the customer has a current backup of the data before doing this task.
Attention: The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect
drive, data or programs can be overwritten.

Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper handling of a system board can
cause damage to those components, and may cause a system malfunction.
Attention: When handling a system board:
• Do not drop a system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.

Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive
(2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS
requirements must be implemented on Lenovo products placed on the market after June 2006. Products
on the market before June 2006 are not required to have RoHS compliant parts. If the original FRU parts
are non-compliant, the replacement parts also can be non-compliant. That is, if the original FRU parts are
RoHS compliant, the replacement part also must be RoHS compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified by the unique
FRU part numbers.
Lenovo plans to transit to RoHS compliance before the implementation date and expects its suppliers to be
ready to meet Lenovo’s requirements and schedule in the European Union. Products sold between 2005
and 2006 might contain some RoHS compliant FRUs. The following statement pertains to the products
with RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS implementation date, the
failed RoHS compliant parts must be replaced with compliant parts and only the following FRUs can be
used: identified as compliant in the Hardware Maintenance Manual or direct substitutions can be used.
• Compliant FRUs identified in Hardware Maintenance Manual
• Direct substitutions with different FRU part numbers automatically shipped by the distribution center at
the time of order
For products shipped after June 2006
Current or original part

Replacement FRU

Must be RoHS

Hardware Maintenance Manual

Chapter 3. General checkout
This chapter presents following information:
• “What to do first” on page 29
• “Power system checkout” on page 30
Before you go to the checkout guide, be sure to read the following important notes.
Important notes:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• When you replace FRUs, it is recommended to use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer
that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs
might be overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model
of the machine and the FRU part number are correct by referring to the FRU parts list.
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a
variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge,
or software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective,
clear the error log and run the test again. If the error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.

What to do first
When you do return a FRU, you must include the following information in the parts exchange form or
parts return form that you attach to it:
1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Procedure index and page number in which the failing FRU was detected
6. Failing FRU name and part number
7. Machine type, model number, and serial number
8. Customer's name and address
Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. Following is a list of some common items that are not covered under warranty
and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is covered under the warranty
by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of an incompatible card
• Improper disc insertion or use of an optical drive
© Copyright Lenovo 2012

• Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive,
or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force,
or dropped.

Power system checkout
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac power adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac power adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
• “Checking the ac power adapter” on page 30
• “Checking operational charging” on page 31
• “Checking the battery pack” on page 31

Checking the ac power adapter
You are here because the computer fails only when the ac power adapter is used.
• If the power-on indicator does not turn on, check the power cord of the ac power adapter for correct
continuity and installation.
• If the computer does not charge during operation, go to “Checking operational charging” on page 31
To check the ac power adapter, do the following:
1. Unplug the ac power adapter cable from the computer.
2. Measure the output voltage at the plug of the ac power adapter cable. See the following figure:

Voltage (V dc)

+20

2
1
(20V)

Note: Output voltage of pin no.2 of the ac power adapter may different from the one you are servicing.
3. If the voltage is not correct, replace the ac power adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem persists, go to Chapter 5 “Lenovo B580” on page 37.

Hardware Maintenance Manual

Note: Noise from the ac power adapter does not always indicate a defect.

Checking operational charging
To check whether the battery charges properly during operation, use a discharged battery pack or a battery
pack that has less than 50% of the total power remaining when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery
pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does
not turn on, replace the battery pack.
If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is
still not charged, go to the next section.

Checking the battery pack
The battery status icon in the Windows® notification area displays the percentage of battery power remaining.
To check for detailed battery status information on the Windows operating system, do the following:
• Windows 7: Launch the Power Manager program and click the Battery tab.
• Windows 8:
– Press the recovery button to launch the Lenovo Solution Center program, and then click Battery.
– Press Fn+Esc to launch the Lenovo Experience program, and then click Battery Health.
To check the battery pack, do the following:
1. Turn off the computer and disconnect the ac power adapter.
2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (-).

1(+)

2(+)

5
3 4

6(-)

Terminal

Voltage (V dc)

+ 0 to + 14

Ground (-)

7(-)

3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not turn on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery pack.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 5 and 7.
The resistance must be 4 to 30 K Ω.
If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system
board.

Chapter 3. General checkout

Hardware Maintenance Manual

Chapter 4. Related service information
This chapter presents the following information:
• “Recovering the computer settings” on page 33
• “Passwords” on page 34
• “Power management” on page 34

Recovering the computer settings
Recovery the computer settings on the Windows 7 operating system
Performing backup and recovery operations using the OneKey® Recovery Pro program
The OneKey Recovery Pro program enables you to back up all your hard disk drive contents including the
operating system, data files, software programs, and personal settings. You can designate where the
OneKey Recovery Pro program stores the backup. After you have backed up the contents on the hard disk
drive, you can restore the complete contents of the hard disk drive, restore only the selected files, or restore
only the Windows operating system and applications.
Restoring factory default settings using the Product Recovery program
On the Windows 7 operating system, you can use recovery media to restore the computer settings to the
factory default settings only.
Attention: When you use the Product Recovery program to restore the computer settings, all the data you
have stored on the hard disk drive will be deleted and the computer settings will be restored to the factory
default settings. During the restoring process, you will be given the option to save one or more files currently
on the hard disk drive to other media before the data is deleted.
Recovery the computer settings on the Windows 8 operating system
Your computer is preinstalled with one Windows recovery program on the Windows 8 operating system.
Restoring factory contents using the Windows recovery program
The Windows recovery program enables you to do the following:
• Refreshing your computer to the factory default settings while preserving the data on the hard disk drive.
• Restoring the factory default settings.
Attention: When you use the Windows recovery program to restore the computer settings, all the data
you have stored on the hard disk drive will be deleted and the computer will be restored to the factory
default settings. To avoid data loss, back up your data in advance.
Advanced startup options
Advanced startup options enable you to do the following:
• Starting up from an external drive or disc
• Changing your computer settings
• Changing the startup settings of the Windows operating system
• Restoring the Windows operating system from a system image

For more information about the recovery solutions provided on your computer, refer to the help information
system of the Windows 8 operating system.

Passwords
As many as two passwords might be needed for a Lenovo notebook computer: the power-on password
and the supervisor password.
If any of these passwords has been set, a prompt for it will be displayed on the screen whenever the
computer is turned on. The computer does not start until the password is entered.
Note: If only a supervisor password is set, the password prompt will not be displayed when the operating
system is started.

Power-on password
A power-on password (POP) protects the system from being powered on by an unauthorized person. The
password must be entered before an operating system can be booted.

Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS. The user must enter the
SVP in order to get access to the BIOS and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to the service technician, there is no
service procedure to reset the password. The system board must be replaced for a scheduled fee.

Power management
Note: Power management modes are not supported for APM operating system.
To reduce power consumption, the computer has three power management modes: screen blank, sleep,
and hibernation.

Screen blank mode
In the following circumstances, the computer goes into screen blank mode:
• The time set on the “Turn off monitor” timer on the Windows 7 operating system expires.
To end screen blank mode and resume normal operation, press any key.
• You have pressed Fn+F2.
To end screen blank mode and resume normal operation, press Fn+F2.

Sleep mode
When the computer enters sleep mode, the following events occur in addition to what occurs in screen
blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.
To enter sleep mode, press Fn+F1.
In certain circumstances, the computer goes into sleep mode automatically:

Hardware Maintenance Manual

• If a “suspend time” has been set on the timer, and the user does not do any operation with the keyboard,
the hard disk drive, the parallel connector, or the diskette drive within that time.
• If the battery indicator blinks orange, indicating that the battery power is low.
To cause the computer to return from sleep mode and resume the operation, do one of the following:
• Press the Fn key.
• Open the LCD cover.
• Turn on the power button.
Also, when the time set on the resume timer elapses, the computer automatically returns from sleep mode
and resumes operation.
Note: The computer does not accept any input immediately after it enters sleep mode. Wait a few seconds
before taking any action to reenter operation mode.

Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk drive.
• The system is powered off.
If you have defined one of the following actions as the event that causes the system to go into hibernation
mode, perform that action.
• Closing the lid.
• Pressing the power button.
Also, the computer goes into hibernation mode automatically in either of the following conditions:
• If a “hibernation time” has been set on the timer, and if the user does not do any operation with the
keyboard, the hard disk drive, the parallel connector, or the diskette drive within that time.
• If the timer conditions are satisfied in suspend mode.
When the power is turned on, the computer returns from hibernation mode and resumes operation. The
hibernation file in the boot record on the hard disk drive is read, and system status is restored from the
hard disk drive.

Chapter 4. Related service information

Hardware Maintenance Manual

Chapter 5. Lenovo B580
This chapter presents the following product-specific service references and parts information:
•

“Specifications” on page 37

•

“Status indicators” on page 38

•

“Fn key combinations” on page 39

Specifications
This topic lists the physical features for the Lenovo B580 models.
Processor
• To view the processor information of your computer, do either of the following:
– Windows 7: Click Start, right-click Computer. Then click Properties.
– Windows 8: From the desktop, move the cursor to the top-right or bottom-right corner of the screen to
display the charms. Then click Settings ➙ PC info.
Memory
• Double data rate 3 (DDR3) synchronous dynamic random access memory (SDRAM)
Storage device
• 2.5-inch (7 mm height or 9.5 mm height) hard disk drive
• mSATA solid-state drive
Note: If the computer is equipped with both a hard disk drive and an mSATA solid-state drive, do not
use the mSATA solid-state drive as a bootable device. The mSATA solid-state drive is used for “cache”
function only.
Display
• Size: 15.6 inches (396 mm)
• Resolution:
– LCD: 1366-by-768
– External monitor: Maximum 2048-by-1536
• Integrated camera
Keyboard
• 6-row Lenovo keyboard
• Recovery button
Interface
• Combo audio jack (stereo headphone or headset)
• Two USB 2.0 connectors
• Two USB 3.0 connectors
• RJ45 Ethernet connector

• HDMI port
• External monitor connector
• 4-in-1 digital media card reader slot
Optical drive
• 12.7 mm Rambo optical drive
Wireless features
• Integrated wireless LAN
• Integrated WiMAX
• 100/1000 Mbps Ethernet communication
Security feature
• Fingerprint reader

Status indicators
This chapter presents the system status indicators that show the status of the computer.

Table 1. Status indicators
Indicator

Meaning

Caps lock

White: Caps Lock mode is enabled. You can enter all alphabetic characters (A-Z) in
uppercase without pressing the Shift key. To enable or disable Caps Lock mode, press
the caps lock key (CapsLk).

Numeric lock

White: The separate numeric keypad on the keyboard is enabled. To enable or disable
the numeric keypad, press the numeric lock key (NmLk).

Hardware Maintenance Manual

Table 1. Status indicators (continued)
Indicator

Meaning

When this indicator is on, the hard disk drive or the optical drive is reading or writing data.

Device access
status indicator

Attention:
• When the indicator is on, do not put the computer into sleep mode or turn off the
computer.
• When the indicator is on, do not move the computer. Sudden physical shock might
cause drive errors.
4

Power and battery
status indicator

• Green: The battery charge level is between 80% and 100%, or the battery discharge
level is between 20% and 100%.
• Slow blinking green: The battery charge level is between 20% and 80%, and
charging is continuing. When the battery charge level reaches 80%, the battery status
indicator stops blinking, but the charging might continue until the battery is 100%
charged.
• Slow blinking orange: The battery charge level is between 5% and 20%, and the
charging is continuing. When the battery charge level reaches 20%, the blinking
color changes to green.
• Orange: The battery discharge level is between 5% and 20%.
• Fast blinking orange: The battery charge or discharge level is 5% or less.
• Off: The battery is detached or the computer is powered off.

Fn key combinations
The following table shows the function of each combination of Fn with a function key.
Table 2. Function key combinations
Key combination

Description

Fn+Esc

Turn on or turn off the integrated camera.

Fn+F1

Enter sleep mode.

Fn+F2

Enable or disable the backlight feature of the computer screen.

Fn+F3

Switch between the computer display and an external monitor.

Fn+F5

Enable or disable the built-in wireless features.

Fn+F6

Enable or disable the click pad.

Fn+F9

Start or pause playback of Windows Media Player.

Fn+F10

Stop playback of Windows Media Player.

Fn+F11

Skip to the previous track.

Fn+F12

Skip to the next track.

Fn+Insert

Enable or disable the scroll lock function.

Fn+PrtSc

Activate the system request.

Fn+Home

Activate the pause function.

Fn+End

Activate the break function.

Fn + up/down arrow

Increase or decrease the display brightness level.

Fn + left/right arrow

Increase or decrease the sound volume.

Chapter 5. Lenovo B580

Hardware Maintenance Manual

Chapter 6. FRU replacement notices
This chapter presents notices related to removing and replacing parts. Read this chapter carefully before
replacing any FRU.
CRU statement for customers:
You can resolve some problems with your product with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and others
are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For
optional-service CRUs, you can either install the CRU yourself or you can request that a Service Provider
install the CRU according to the warranty service for your product. If you intend on installing the CRU,
Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your
product and are available from Lenovo at any time upon request. You can find a list of CRUs for your
product in this Hardware Maintenance Manual. An electronic version of this manual can be found at
http://www.lenovo.com/UserManuals. Follow the on-screen instructions to find the manual for your product.
You might be required to return the defective CRU. When return is required: (1) return instructions, a prepaid
shipping label, and a container will be included with the replacement CRU; and (2) you might be charged for
the replacement CRU if Lenovo does not receive the defective CRU within thirty (30) days of your receipt of
the replacement CRU. See your Lenovo Limited Warranty documentation for full details.

Screw notices
Loose screws can cause a reliability problem. In the Lenovo notebook computer, this problem is addressed
with special nylon-coated screws that have the following characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
Do the following when you service this machine:
•
•
•
•

Keep the screw kit in your tool bag.
It is recommended to use new screws.
It recommended to use each screw only once.
Use a torque screwdriver if you have one.

Tighten screws as follows:
• Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the plastic part:

• Logic card to plastic
Turn an additional 180 degrees after the screw head touches the surface of the logic card:

• Torque driver
If you have a torque screwdriver, refer to the Torque column in the screw information table for each step.
• Make sure that you use the correct screw. It is recommended to use new screws for replacements. If
you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information
table for each step.
• Ensure torque screw drivers are calibrated correctly following country specifications.

Hardware Maintenance Manual

Chapter 7. Removing and replacing a FRU
This chapter provides instructions on how to remove or replace a FRU.
CRU statement for customers:
You can resolve some problems with your product with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and others
are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For
optional-service CRUs, you can either install the CRU yourself or you can request that a Service Provider
install the CRU according to the warranty service for your product. If you intend on installing the CRU,
Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your
product and are available from Lenovo at any time upon request. You can find a list of CRUs for your
product in this Hardware Maintenance Manual. An electronic version of this manual can be found at
http://www.lenovo.com/UserManuals. Follow the on-screen instructions to find the manual for your product.
You might be required to return the defective CRU. When return is required: (1) return instructions, a prepaid
shipping label, and a container will be included with the replacement CRU; and (2) you might be charged for
the replacement CRU if Lenovo does not receive the defective CRU within thirty (30) days of your receipt of
the replacement CRU. See your Lenovo Limited Warranty documentation for full details.

General guidelines
This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe
the following general rules:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs
the risk of damaging parts.
2. Before replacing any FRU, review Chapter 6 “FRU replacement notices” on page 41.
3. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Such FRUs are
listed in each FRU replacement section. Remove them in the order in which they are listed.
4. Follow the correct sequence in the steps for removing a FRU, as given in the drawings by the numbers
in square callouts.
5. When turning a screw, turn it in the direction as given by the arrow in the drawing.
6. When removing a FRU, move it in the direction as given by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to
replacement.
8. When replacing a FRU, use the correct screw(s) as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets,
remove the battery pack, and then disconnect any interconnecting cables.
Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws,
springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking
the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before
touching it, establish personal grounding by touching a ground point with one hand or by using an
electrostatic discharge (ESD) strap (P/N 6405959).

1010 Battery pack
Removal steps of battery pack
DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.
Unlock the spring-loaded battery latch 1 . Holding the manual battery latch in the unlocked position, remove
the battery pack in the direction shown by the arrow 2 .

1
2

When installing: Install the battery pack in the slot. Make sure that the battery latches are in the locked
position.

1020 Bottom slot cover
For access, remove this FRU:
• “1010 Battery pack” on page 44

Hardware Maintenance Manual

Removal steps of bottom slot cover
Remove the screws 1 , and then remove the cover 2 .
1
1

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (2)

Black

1.85 kgfcm

1030 Optical drive
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
Removal steps of optical drive
Remove the screw 1 .
1

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

Chapter 7. Removing and replacing a FRU

Insert a screwdriver into the screw hole 2 and push the optical drive in the direction shown by the arrow 3 .
Then remove the optical drive.

Removal steps of optical drive bezel and optical drive bracket

Remove the screws 1 and then remove the optical drive bracket.

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (2)

Black

1.85 kgfcm

1040 Memory modules
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44

Hardware Maintenance Manual

•

“1020 Bottom slot cover” on page 44

Removal steps of memory modules
Release the two latches on both edges of the socket at the same time in the direction shown by the arrows
1 , and then unplug the memory module in the direction shown by the arrow 2 .

1
2

Note: If only one memory module is used on the computer you are servicing, the card must be installed in
SLOT-0 ( a : lower slot), but not in SLOT-1 ( b : upper slot).
b

When installing: Insert the notched end of the memory module into the socket. Press the memory module
firmly, and pivot it until it snaps into place. Make sure that it is firmly installed in the slot and does not
move easily.

1050 Hard disk drive assembly
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44

Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper
handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the computer is operating or is in suspend mode.

Chapter 7. Removing and replacing a FRU

Removal steps of hard disk drive assembly
Remove the screw 1 , then pull the tab in the direction shown by the arrow 2 .

1
2

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

Remove the hard disk drive from the slot 3 .

When installing: Make sure that the hard disk drive connector is attached firmly.

Hardware Maintenance Manual

Removal steps of hard disk drive bracket
Remove the screws 1 .
1

1
1

Step

Screw (quantity)

Color

Torque

M3 × 4 mm, flat-head, nylon-coated (4)

Silver

4 kgfcm

Remove the hard disk drive bracket as shown by the arrow 2 .
2

1060 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44

Chapter 7. Removing and replacing a FRU

Removal steps of PCI Express Mini Card for wireless LAN
In steps 1 , disconnect the cables from the card using the removal tool antenna RF connector (P/N: 08K7159)
or pick up the cables with your fingers and then gently disconnecting the cable from the card in the direction
of the arrows. Then remove the screw 2 .

1
1
2

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

Remove the card in the direction shown by the arrow 3 .

When installing: Plug the black cable (MAIN) into the jack labeled M, and the white cable (AUX) into the jack
labeled A on the card.

Hardware Maintenance Manual

1070 mSATA solid-state drive
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

Chapter 7. Removing and replacing a FRU

Remove the mSATA solid-state drive 2 .

1080 Backup battery
Removal steps of backup battery
DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.
Insert a screwdriver into the backup battery hole and push the backup battery until the battery pops up.

When installing: Make sure that the connector is attached firmly.

Hardware Maintenance Manual

1090 Keyboard
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
Removal steps of keyboard
Remove the screws 1 .
1

1
1

When installing: Make sure that the screws have been fastened to secure the keyboard.
Step

Screw (quantity)

Color

Torque

M2.5 × 8 mm, flat-head, nylon-coated (3)

Black

4.0 kgfcm

Push hard in the direction shown by the arrows 2 to unlatch the front side of the keyboard.

Chapter 7. Removing and replacing a FRU

Remove the keyboard in the direction shown by the arrow 3 .

Carefully lift the keyboard until you can see how it’s connected. Hold the keyboard above the computer
4 , and then detach the keyboard connector 5 6 .

Hardware Maintenance Manual

6
5

When installing: Make sure that the keyboard connector is attached firmly.

1100 Keyboard bezel
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1090 Keyboard” on page 53

Chapter 7. Removing and replacing a FRU

Removal steps of keyboard bezel
Remove the screws 1 and 2 that secure the keyboard bezel.
2

2
1
1

1
1

Step

Screw (quantity)

Color

Torque

M2.5 × 8 mm, flat-head, nylon-coated (10)

Black

4.0 kgfcm

M2 × 3 mm, flat-head, nylon-coated (3)

Black

1.85 kgfcm

Remove the screws 3 .

3
3

Step

Screw (quantity)

Color

Torque

M2 × 5 mm, flat-head, nylon-coated (3)

Black

1.85 kgfcm

Hardware Maintenance Manual

Detach the connectors.

5
4

When installing: Make sure that all the connectors are attached firmly.
Remove the keyboard bezel.

12
12
12
13

12
12
12
12

12
12

Chapter 7. Removing and replacing a FRU

1110 Fingerprint board and LED board
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
Removal steps of fingerprint board
Remove the screw 1 and the fingerprint board bracket 2 . Then remove the fingerprint board 3 .
1
2
3
3

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Silver

1.85 kgfcm

Hardware Maintenance Manual

Removal steps of LED board
Peel off the mylar tape 1 . Then remove the LED board 2 .

1120 Power board and touch pad bracket
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55

Chapter 7. Removing and replacing a FRU

Removal steps of power board
Remove the screw 1 and then remove the power board 2 .

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

Removal steps of touch pad bracket
Remove the screw 1 and then remove the touch pad bracket 2 .

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

1130 Microphone assembly
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
Removal steps of microphone assembly
Detach the connector 1 , and then remove the microphone assembly in the direction shown by the arrow 2 .

Hardware Maintenance Manual

When installing: Make sure that the connector is attached firmly to the system board.

1140 I/O board
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55

Chapter 7. Removing and replacing a FRU

Removal steps of I/O board
Remove the screws 1 , and then detach the cable 2 3 . Remove the I/O board 4 .

Step

Screw (quantity)

Color

Torque

M2 × 5 mm, flat-head, nylon-coated (2)

Black

1.85 kgfcm

When installing: Make sure that the cable is attached firmly to the system board.

1150 System board assembly and USB board
Important notices for handling the system board:
When handling the system board, bear the following in mind:
• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
• Avoid rough handling of any kind.
• At every point in the process, be sure not to drop or stack the system board.
• If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or a corrugated
conductive surface.

Hardware Maintenance Manual

For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid-state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
Removal steps of system board assembly
Remove the screws 1 , and then detach the connectors as shown in the following illustration.

2
3

1
1

6
7

Step

Screw (quantity)

Color

Torque

M2 × 5 mm, flat-head, nylon-coated (2)

Black

1.85 kgfcm

When installing: Make sure that all the connectors are attached firmly.

Chapter 7. Removing and replacing a FRU

Detach the DC-in cable 11 . Remove the system board in the direction shown by the arrow 12 .

Removal steps of USB board
Remove the screw 1 , and then detach the connectors as shown in the following illustration. Remove
the USB board 4 .

3
2

1
4

Step

Screw (quantity)

Color

Torque

M2 × 5 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

Hardware Maintenance Manual

1160 DC-in connector
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid-state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1140 I/O board” on page 61
• “1150 System board assembly and USB board” on page 62
Removal steps of DC-in connector
Detach the connector 1 . Remove the screw 2 and the DC-in connector bracket 3 . Then remove the DC-in
connector in the direction shown by the arrow 4 .

2
3

Step

Screw (quantity)

Color

Torque

M2 × 3 mm, flat-head, nylon-coated (1)

Black

1.85 kgfcm

Chapter 7. Removing and replacing a FRU

1170 Thermal module
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid-state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1150 System board assembly and USB board” on page 62
Removal steps of thermal module
Detach the fan connector 1 .

When installing: Make sure that the connector is attached firmly.

Hardware Maintenance Manual

Loosen the screws 2 to 8 .

7
8
6
5
2
4
3

Note: Different models might have different numbers of screws.
Lift the fan assembly in the direction shown by the arrow 9 .
Note: Be careful not to damage the connector.

Chapter 7. Removing and replacing a FRU

When installing: Before you attach the thermal module to the computer, apply thermal grease, at an amount
of 0.2 grams, on the part marked a and b as shown in the following illustration. Either too much or too less
application of grease can cause a thermal problem due to imperfect contact with a component.
For models with a discrete thermal module

For models with an integrated thermal module

1180 CPU
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid-state drive” on page 51
• “1080 Backup battery” on page 52

Hardware Maintenance Manual

•
•
•
•
•

“1090 Keyboard” on page 53
“1100 Keyboard bezel” on page 55
“1130 Microphone assembly” on page 60
“1150 System board assembly and USB board” on page 62
“1170 Thermal module” on page 66

Attention: The CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling.
Removal steps of CPU
Rotate the head of the screw in the direction shown by the arrow 1 to release the lock, then remove the
CPU 2 .

a
b

When installing: Place the CPU above the CPU socket a , and then rotate the head of the screw in the
direction shown by the arrow b to secure the CPU.

1190 LCD unit
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid-state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53

Chapter 7. Removing and replacing a FRU

•
•
•
•
•

“1100 Keyboard bezel” on page 55
“1130 Microphone assembly” on page 60
“1140 I/O board” on page 61
“1150 System board assembly and USB board” on page 62
“1160 DC-in connector” on page 65

Removal steps of LCD unit
Release the antenna cables from the cable guides. Then remove the screws 1 .

1
1

Step

Screw (quantity)

Color

Torque

M2.5 × 5 mm, flat-head, nylon-coated (4)

Black

4 kgfcm

When installing:
• Route the antenna cables along the cable guides. As you route the cables, make sure that they are
not subjected to any tension. Tension could cause the cables to be damaged by the cable guides,
or a wire to be broken.
• Make sure that the LCD connector is attached firmly and make sure that you do not pinch the antenna
cables when you attach the LCD assembly. Route the LCD cable along the cable guides.

Hardware Maintenance Manual

Remove the LCD unit in the direction shown by the arrow 2 .

1200 Speaker assembly
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid-state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1140 I/O board” on page 61
• “1150 System board assembly and USB board” on page 62
• “1160 DC-in connector” on page 65
• “1190 LCD unit” on page 69

Chapter 7. Removing and replacing a FRU

Removal steps of speaker assembly
Remove the screws 1 . Then remove the speaker assembly 2 .
1
1
2

Step

Screw (quantity)

Color

Torque

M2.5 × 5.7 mm, flat-head, nylon-coated (4)

Black

4.0 kgfcm

1210 Base cover
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1020 Bottom slot cover” on page 44
• “1030 Optical drive” on page 45
• “1040 Memory modules” on page 46
• “1050 Hard disk drive assembly” on page 47
• “1060 PCI Express Mini Card for wireless LAN” on page 49
• “1070 mSATA solid-state drive” on page 51
• “1080 Backup battery” on page 52
• “1090 Keyboard” on page 53
• “1100 Keyboard bezel” on page 55
• “1130 Microphone assembly” on page 60
• “1140 I/O board” on page 61
• “1150 System board assembly and USB board” on page 62
• “1160 DC-in connector” on page 65
• “1190 LCD unit” on page 69
• “1200 Speaker assembly” on page 71
Applying labels to the base cover
The new base cover is shipped with a kit containing labels of several kinds. Apply those labels listed when
you replace the base cover. For the labels which are not shipped with the new base cover, peel them off
from the old base cover, and adhere them to the new one.
Note: If you replace a part with the Windows Certificate of Authentication (COA) label 11 , return the old part
with the label attached to the customer. Otherwise, you can provide the customer with a letter, stating the
original location of the label on the computer and the information on the label, such as the part number,
serial number, and product key.
72

Hardware Maintenance Manual

The following illustration shows the label locations on the base cover.

12
1
11
10
2

3
4
5
6
7
8

9
1 WWAN IMEI barcode label

7 Brazil WLAN label / WLAN label for United
States/Canade/Taiwan

2 China label, KCC label, or MAC label

8 PPT label

3 Indonesia D side label

9 Malaysia SIRIM label

4 Indonesia WLAN and Bluetooth label

10 Vodafone label

5 Israel label

12 Rating label

6 Brazil Bluetooth label or Bluetooth label for United
States/Canade/Taiwan

2010 LCD front bezel
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1190 LCD unit” on page 69

Chapter 7. Removing and replacing a FRU

Removal steps of LCD front bezel
Remove the screws 1 .
1

Step

Screw (quantity)

Color

Torque

M2 × 3.5 mm, flat-head, nylon-coated (2)

Black

1.85 kgfcm

Remove the LCD front bezel in the direction shown by the arrows 2 .

2
2

When installing: Make sure that all the latches are attached firmly. Then secure the bezel with the screws.

2020 Integrated camera
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1190 LCD unit” on page 69
• “2010 LCD front bezel” on page 73

Hardware Maintenance Manual

Removal steps of integrated camera
Remove the integrated camera from the LCD cover as shown in the following illustration.
Note: The integrated camera is stuck on the top center of the LCD cover.
1

When installing: Stick the integrated camera to the top center of the LCD cover and adjust the placement to
make sure that the connector is attached firmly.

2030 LCD panel, LCD cable, and hinges
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1190 LCD unit” on page 69
• “2010 LCD front bezel” on page 73

Chapter 7. Removing and replacing a FRU

Removal steps of LCD panel and LCD cable
Remove the screws 1 . Then remove the LCD panel in the direction shown by the arrow 2 .
1

1
2
1

Step

Screw (quantity)

Color

Torque

M2 × 3.5 mm, flat-head, nylon-coated (6)

Black

1.85 kgfcm

Turn over the LCD panel 3 . Remove the LCD cable.

5
4

When installing: Make sure that the connector is attached firmly.

Hardware Maintenance Manual

Removal steps of hinges
Remove the screws 1 . Then remove the hinges 2 .
1

2
1

1
2

Step

Screw (quantity)

Color

Torque

M2 × 3.5 mm, flat-head, nylon-coated (4)

Black

1.85 kgfcm

2040 Antenna assembly and LCD rear cover
For access, remove these FRUs in order:
• “1010 Battery pack” on page 44
• “1190 LCD unit” on page 69
• “2010 LCD front bezel” on page 73
• “2020 Integrated camera” on page 74
• “2030 LCD panel, LCD cable, and hinges” on page 75

Chapter 7. Removing and replacing a FRU

Removal steps of antenna assembly and LCD rear cover
Release the antenna cables from the cable guides of the LCD rear cover assembly and from the hinges in
the direction shown by the arrows 1 .

Cable routing: Route the antenna cables along the cable guides and secure the antenna boards with
adhesive tapes. As you route the cables, make sure that they are not subjected to any tension. Tension
could cause the cables to be damaged by the cable guides, or a wire to be broken.

Hardware Maintenance Manual

Chapter 8. Locations
This chapter presents the locations of the Lenovo B580 hardware components.

Front and right-side view
2
1
2

17
16
15

3
4

14
13
5
12

6
7
8
11
10

Figure 1. Lenovo B580 front and right-side view
1 Integrated camera (on some models)

10 Combo audio jack

2 Wireless module antennas

11 Media card reader slot

3 Status indicators1

12 Touch pad

4 Speaker (right)

13 Microphone

5 ac power connector

14 Power and battery indicator1

6 USB connector

15 Power button

7 Optical drive

16 Recovery button

8 Fingerprint reader (on some models)

17 Speaker (left)

9 USB connector
1

For the description of the indicators, see “Status indicators” on page 38.

Bottom and left-side view
1
2
3

4
5

10
8

Figure 2. Lenovo B580 bottom and left-side view
1 Battery latch (manual)

6 Monitor connector

2 Battery pack

7 Ethernet connector

3 Battery latch (spring loaded)

8 HDMI port

4 Security keyhole

9 USB 3.0 connectors

5 Fan louvers

10 Bottom slot cover1

The memory modules, hard disk drive, and wireless cards are located underneath the bottom slot cover.

Hardware Maintenance Manual

Chapter 9. Parts list
This chapter contains following lists of the service parts.
• “Overall” on page 82
• “LCD FRUs” on page 85
• “Keyboard” on page 87
• “Miscellaneous parts” on page 89
• “ac power adapters” on page 90
• “Power cords” on page 91
Notes:
• Each FRU is available for all types or models, unless otherwise specified.
• A CRU is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An N in the CRU ID column
means that the part is not a CRU. A single asterisk (*) means that the part is a self-service CRU; two asterisks
(**) means that the part is an optional-service CRU.
CRU statement for customers:
You can resolve some problems with your product with a replacement part you can install yourself, called a
“Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and others are
designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For optional-service
CRUs, you can either install the CRU yourself or you can request that a Service Provider install the CRU according
to the warranty service for your product. If you intend on installing the CRU, Lenovo will ship the CRU to you. CRU
information and replacement instructions are shipped with your product and are available from Lenovo at any time
upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic
version of this manual can be found at http://www.lenovo.com/UserManuals. Follow the on-screen instructions to
find the manual for your product. You might be required to return the defective CRU. When return is required: (1)
return instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you
might be charged for the replacement CRU if Lenovo does not receive the defective CRU within thirty (30) days of
your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
Lenovo computers contain the following types of CRUs:
– Self-service CRUs: These CRUs unplug or are held by no more than two screws. Examples of these types
of CRUs include the ac power adapter, power cord, battery, and hard disk drive. Other self-service CRUs
depending on product design might include the memory module, wireless card, keyboard, and palm rest
with finger print reader and touch pad.
– Optional-service CRUs: These CRUs are isolated parts within the computer that are concealed by an access
panel that is typically secured by more than two screws. Once the access panel is removed, the specific
CRU is visible.

Overall

2
a

3
22
4
21
20

b
5
c
d

19
18
17

6
7
8
e

16
9

10
f

11
g

14
12
13

Table 3. Parts list—Overall
No. FRU (Overall)

FRU No.

CRU
ID

LCD unit (see “LCD FRUs” on page 85.)

LB58 Power Board

90000235

LB58 LED Board W/Cable

90200814

Hardware Maintenance Manual

Table 3. Parts list—Overall (continued)
No. FRU (Overall)

FRU No.

CRU
ID

LB58 Upper Case W/TP

90200819

LB58 FingerPrint Board

90000236

LB58 USB Board

90000233

LB58 Speaker R

90200832

Battery, 6CELL 2.2Ah，Sanyo 2.2Ah 48Wh 6cell battey

121500047

Battery, 6CELL 2.2Ah, LG 2.2Ah 48Wh 6cell battey

121500049

Battery, 6CELL 2.2Ah, SMP 2.2Ah 48Wh 6cell battey

121500050

Battery, 6CELL 2.8Ah, SA L11S6F01 3S2P 62Wh Batt C01 Origa

121500051

Battery, 6CELL 2.8Ah, LG L11L6F01 3S2P 62Wh Batt C01 Origa

121500052

Battery, 6CELL 2.8Ah, SM/S L11M6F01 3S2P 62Wh Batt C01 Origa

121500053

LB58 DC-IN Cable

90200811

LB58 Lower Case

90200822

ODD, 12.7mm Tray-in Rambo, PLDS, DS-8A8SH

25201487

ODD, 12.7mm Tray-in Rambo, Sony Optiarc, AD-7740H

25201106

ODD, 12.7mm Tray-in Rambo, TSST, SN-208AB

25201108

ODD, 12.7mm Tray-in Rambo, HLDS, GT50N

25201635

LB58 IO Board

90000234

LB58 Memory Door

90200816

HDD, 320G 5400rpm, Toshiba Capricorn BS (H6sp)，Toshiba MK3265GSX 5400RPM
320G

16200097

HDD, 320G 5400rpm, HGST Jaquar B7, HGST HTS545032A7E380 5400PRM7mm 320G

16200068

HDD, 320G 5400rpm, Seagate Sapta 15, Seagate ST320LT020 5400RPM 7MM 320G

16005211

HDD, 500G 5400rpm, WD ML500M, WD5000BPVT-08A1Y

16200118

HDD, 500G 5400rpm, WD ML375M, WD5000BPVT-08HXZ

16200090

HDD, 500G 5400rpm, Toshiba Capricorn BS (H6sp), Toshiba MK5065GSX 5400RPM 500G

16200098

HDD, 750G 5400rpm, WD ML500M, WD7500BPVT-08A1Y

16200119

HDD, 750G 5400rpm, WD ML375M, WD7500BPVT-08HXZ

16200121

HDD, 750G 5400rpm, HGST Jaguar B, HTS541075A9E680

16200192

HDD, 1TB 5400rpm, WD ML500M, WD10JPVT-08A1Y

16200120

HDD, 1TB 5400rpm, HGST Jaquar B, HTS541010A9E680

16200193

HDD, 320G 7200rpm, WD MX320S-1, WD3200BEKT-08PVM

16200092

HDD, 320G 7200rpm, Toshiba Capricorn CS (H6sp), TSB MK3261GSY 7200PRM 9.5mm
320G HDD

16200099

HDD, 320G 7200rpm, HGST Jaquar C7, HTS725032A7E630

16200194

HDD, 320G 7200rpm, Seagate Julius 1 4K, Seagate ST320LT007 7200RPM 7MM 320G

16005030

HDD, 500G 7200rpm, WD MX375M, WD5000BPKT-08PK4T

16200124

HDD, 500G 7200rpm, Toshiba Capricorn CS (H6sp), TSB MK5061GSY 7200PRM 9.5mm
500G HDD

16200100

Chapter 9. Parts list

Table 3. Parts list—Overall (continued)
No. FRU (Overall)

FRU No.

CRU
ID

HDD, 500G 7200rpm, Jaguar C7, HTS725050A7E630

16200195

LB58 Microphone

90200829

LB58 Speaker L

90200833

SSD, mSATA 16G, Sandisk, U100 mSATA SDSA5DK-016G

16200215

SSD, mSATA 16G, Lite-on, LMT-16M3M

16200241

WLAN, Non-Intel 1x1 11bgn + BT4.0 Combo, Broadcom 4313 + 20702

20200100
20200101

WLAN, Non-Intel 2x2 11abgn + BT4.0 Combo, Broadcom 43228 + 20702

20200098
20200099

WLAN, Intel 2x2 11bgn + BT4.0 Combo, Jackson Peak 1

20200078

WLAN, Non-Intel 1x1 11bgn, Broadcom BCM4313 1*1 BGN MOW

20200102

WLAN, Non-Intel 1x1 11bgn, Realtek bgn 1x1 HMC WLAN Stockton

20200016

RAM, DDRIII 1600 2GB, Samsung, M471B5773DH0-CK0 DDR3 1600 2GB

11200340

RAM, DDRIII 1600 2GB, Samsung, M471B5273CH0-CK0 DDR3 1600 2GB

11201312

RAM, DDRIII 1600 2GB, Hynix, HMT325S6CFR8C-PB DDR3 1600 2GB

11200343

RAM, DDRIII 1600 2GB, Micron, MT8KTF25664HZ-1G6M1 DDR3 1600 2GB

11200346

RAM, DDRIII 1600 2GB, Ramaxel, RMT3150ED58E8W-1600 DDR3 1600 2GB

11200392

RAM, DDRIII 1600 2GB, Nanya, NT2GC64B88G0NS-DI DDR3 1600 2GB

11201041

RAM, DDRIII 1600 2GB, Sharetronic(Micron), SM321NH08IAF DDR3 1600 2GB

11200396

RAM, DDRIII 1600 4GB, Samsung, M471B5273DH0-CK0 DDR3 1600 4GB

11200341

RAM, DDRIII 1600 4GB, Samsung, M471B5273CH0-CK0 DDR31600 4GB

11201311

RAM, DDRIII 1600 4GB, Hynix, HMT351S6CFR8C-PB DDR3 1600 4GB

11200344

RAM, DDRIII 1600 4GB, Micron, MT16KTF51264HZ-1G6M1 DDR3 1600 4GB

11200347

RAM, DDRIII 1600 4GB, Ramaxel, RMT3160ED58E9W-1600 DDR3 1600 4GB

11200393

RAM, DDRIII 1600 4GB, Nanya, NT4GC64B8HG0NS-DI DDR3 1600 4GB

11201042

RAM, DDRIII 1600 4GB, Sharetronic(Micron), SM322NQ08IAF DDR3 1600 4GB

11200397

LB58 MB UMA W/HDMI WO/3G

90000239

LB58 MB DIS N13P-GE 1G W/HDMI WO/3G

90000240

LB58 MB UMA W/HDMI WO/SBA/3G

90000418

LB58 MB DIS N13P-GE 1G W/HDMI WO/3G/SBA

90000419

LB58 MB W8 UMA W/HDMI/SBA WO/3G

90001613

LB58 MB W8P UMA W/HDMI/SBA WO/3G

90001614

LB58 MB W8 UMA W/HDMI WO/SBA/3G

90001615

LB58 MB W8P UMA W/HDMI WO/SBA/3G

90001616

LB58 MB W8 DIS N13P-GE 1G W/HDMI/SBA WO/3G

90001617

LB58 MB W8P DIS N13P-GE 1G W/HDMI/SBA WO/3G

90001618

LB58 MB W8 DIS N13P-GE 1G WO/3G/SBA

90001619

LB58 MB W8P DIS N13P-GE 1G WO/3G/SBA

90001620

Hardware Maintenance Manual

Table 3. Parts list—Overall (continued)
No. FRU (Overall)

FRU No.

CRU
ID

CPU, Intel I5-2520M 2.5G 3M 2c J1 PGA processor

102001067

CPU, Intel B815 1.6G Q0 2M 2cPGA processor

102500229

CPU, Intel I3-2370M 2.4G J1 3M 2cPGA processor

102500228

CPU, Intel SNB I3-2350M 2.3G 3M J1 PGA processor

102500018

CPU, Intel SNB I3-2330M 2.2G 3M J1 PGA processor

102500017

CPU, Intel SNB B950 2.1G 2M Q0 PGA processor

102500016

CPU, Intel SNB B940 2.0G 2M Q0 PGA processor

102500015

CPU, Intel SNB I3-2310M 2.1G 3M 2c J1 PGA processor

102001065

CPU, Intel B970 2.3G D2 2M 2cPGA processor

102500230

CPU, Intel SNB B800 1.5G Q0 2M 2c PGA processor

102500101

CPU, Intel SNB B960 2.2G 2M 35W PGA processor

102500133

CPU, Intel B820 1.7G Q0 2M 2cPGA processor

102500350

CPU, Intel I3-2308M 2.1G Q0 3M 2cPGA processor

102500351

CPU, i5-3210M Ivy Bridge L-0 3MB 2c PGA 2.5GHz STD 35W processor

102500301

CPU, i3-3110M Ivy Bridge L-0 3MB 2c PGA 2.3GHz STD 35W processor

102500303

LB58 Thermal Module UMA W/FAN

90200827

LB58 Thermal Module DIS W/FAN

90200828

Keyboard (see “Keyboard” on page 87.)

—

ac power adapter (see “ac power adapters” on page 90.)

LCD FRUs
In Lenovo B580 models, the type of LCD is 15.6-inch high definition (HD) TFT LCD (Table 4 “Parts list LCD” on page 86).

Chapter 9. Parts list

2
7

3
k

Table 4. Parts list - LCD
No. FRU

FRU No.

CRU
ID

LB58 LCD Bezel

90200824

LB58 Hinge L+R

90200817

LB58 Antenna R

90200826

LB58 Camera 0.3M

90000238

LB58 LCD Cover

90200823

LB58 Antenna L

90200825

Panel, 15.6 HD Wedge Glossy, SEC, LTN156AT24-L01

18200114

Panel, 15.6 HD Wedge Glossy, LGD, LP156WH4-TLN1

18200158

Panel, 15.6 HD Wedge Glossy, AUO, B156XTN02.0

18200157

Panel, 15.6 HD Wedge Anti-Glare, AUO, B156XTN02.1

18200649

Panel, 15.6 HD Wedge Anti-Glare, SEC, LTN156AT24-401

18200650

Panel, 15.6 HD Wedge Anti-Glare, CMI, N156BGE-L11

18200651

Hardware Maintenance Manual

Keyboard
Table 5. Parts list - Keyboard (Dafon)
Language

FRU NO.
(Windows 7)

FRU NO.
(Windows 8)

CRU ID

Arabic

25204626

25209766

Belgian

25204634

25209774

Brazilian Portuguese

25204627

25209767

Bulgarian

25204640

25209780

French, English

25204620

25209779

Czech, Slovak

25204639

25209779

C& Nordics

25204633

25209773

Dutch

25204629

25209769

French

25204624

25209764

German

25204625

25209765

Greek

25204630

25209770

Hebrew

25204631

25209771

Hungarian

25204632

25209772

Icelandic

25204635

25209775

Indian

25204641

25209781

Italian

25204614

25209754

Japanese

25204628

25209768

Korean

25204621

25209761

Latin

25204619

25209759

Portuguese

25204618

25209758

Russian

25204623

25209763

Slovenian

25204636

25209776

Swiss

25204637

25209777

Spanish

25204615

25209755

Thai

25204617

25209757

Traditional Chinese

25204622

25209762

Turkish

25204616

25209756

U.K. English

25204613

25209753

U.S. English

25204612

25209752

U.S. English (International, with a Euro symbol)

25204638

25209778

Language

FRU NO.
(Windows 7)

FRU NO.
(Windows 8)

CRU ID

Arabic

25204656

25209796

Belgian

25204664

25209804

Table 6. Parts list - Keyboard (Sunrex)

Chapter 9. Parts list

Table 6. Parts list - Keyboard (Sunrex) (continued)
Language

FRU NO.
(Windows 7)

FRU NO.
(Windows 8)

CRU ID

Brazilian Portuguese

25204657

25209797

Bulgarian

25204670

25209810

Czech, Slovak

25204669

25209809

C& Nordics

25204663

25209803

Dutch

25204659

25209799

French

25204654

25209794

French, English

25204650

25209790

German

25204655

25209795

Greek

25204660

25209800

Hebrew

25204661

25209801

Hungarian

25204662

25209802

Icelandic

25204665

25209805

Indian

25204671

25209811

Italian

25204644

25209784

Japanese

25204658

25209798

Korean

25204651

25209791

Latin

25204649

25209789

Portuguese

25204648

25209788

Russian

25204653

25209793

Swiss

25204667

25209807

Spanish

25204645

25209785

Slovenian

25204666

25209806

Thai

25204647

25209787

Traditional Chinese

25204652

25209792

Turkish

25204646

25209786

U.K. English

25204643

25209783

U.S. English

25204642

25209782

U.S. English (International, with a Euro symbol)

25204668

25209808

Language

FRU NO.
(Windows 7)

FRU NO.
(Windows 8)

CRU ID

Arabic

25204597

25209737

Belgian

25204604

25209744

Brazilian Portuguese

25204598

25209738

Bulgarian

25204610

25209750

Czech, Slovak

25204609

25209749

C& Nordics

25204603

25209743

Table 7. Parts list - Keyboard (Chicony)

Hardware Maintenance Manual

Table 7. Parts list - Keyboard (Chicony) (continued)
Language

FRU NO.
(Windows 7)

FRU NO.
(Windows 8)

CRU ID

Dutch

25204599

25209739

French

25204595

25209735

French, English

25204591

25209731

German

25204596

25209736

Greek

25204600

25209740

Hebrew

25204601

25209741

Hungarian

25204602

25209742

Indian

25204611

25209751

Icelandic

25204605

25209745

Italian

25204585

25209725

Japanese

25204584

25209724

Korean

25204592

25209732

Latin

25204590

25209730

Portuguese

25204589

25209729

Russian

25204594

25209734

Slovenian

25204606

25209746

Swiss

25204607

25209747

Spanish

25204586

25209726

Thai

25204588

25209728

Traditional Chinese

25204593

25209733

Turkish

25204587

25209727

U.K. English

25204583

25209723

U.S. English

25204582

25209722

U.S. English (International, with a Euro symbol)

25204608

25209748

Miscellaneous parts
Table 8. Parts list - Miscellaneous parts
FRU

FRU No.

CRU
ID

(a) LB58 Power Board Cable

90200809

(b) LB58 FP Board Cable

90200810

90200818

(d) LB58 USB Cable

90000237

(e) LB58 DC-IN Bracket

90200821

(f) LA48 ODD Bracket 33.4TD06.001

90200518

(g) LB58 ODD Bezel Rambo

90200815

(h) LA48 HDD Bracket 60.4TE08.001

90200520

Chapter 9. Parts list

Table 8. Parts list - Miscellaneous parts (continued)
FRU

FRU No.

CRU
ID

(i) LB58 TP Bracket

90200820

(j) LB58 TP Cable

90200813

(k) LB58 LCD Cable

90200812

LB58 Microphone Rubber

90200830

LB58 LCD Bezel Screw Pad

90200831

Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 82.

ac power adapters
Table 9. Parts list—2-pin (65 W) ac power adapters
FRU

FRU No.

CRU ID

Delta ADP-65AD AA, EuP model

36200090

Liteon PA-1650-75I, EuP model

36200092

Chicony Power A065R040L, EuP model

36200094

Delta ADP-65SB A, EPA model

36200143

Liteon PA-1650-53I, EPA model

36200144

Chicony Power A065R028L, EPA model

36200210

FRU

FRU No.

CRU ID

Delta ADP-65AD BA, EuP model

36200096

Liteon PA-1650-76I, EuP model

36200097

Chicony Power A065R041L, EuP model

36200098

Delta ADP-65SB B, EPA model

36200033

Liteon PA-1650-54I, EPA model

36200034

Chicony Power A065R017L, EPA model

36200212

FRU

FRU No.

CRU ID

Delta ADP-90SD AA, EuP model

36200102

Liteon PA-1900-75I, EuP model

36200101

Chicony Power A090A047L, EuP model

36200103

Delta PA-1900-53I, EPA model

36200147

Liteon ADP-90ZH CA, EPA model

36200149

Chicony Power HP-A0905A2C1LF, EPA model

36200150

Table 10. Parts list—3-pin (65 W) ac power adapters

Table 11. Parts list—2-pin (90 W) ac power adapters

Hardware Maintenance Manual

Table 12. Parts list—3-pin (90 W) ac power adapters
FRU

FRU No.

CRU ID

Delta ADP-90SD BA, EuP model

36200106

LITEON PA-1900-76I, EuP model

36200105

Chicony A090A048L, EuP model

36200107

Liteon PA-1900-54I, EPA model

36200030

Delta ADP-90ZH DA, EPA model

36200031

Chicony Power HP-BT090E13LF, EPA model

36200032

Power cords
A Lenovo power cord for a specific country or region is usually available only in that country or region.
Table 13. Parts list - 3-pin power cords (Linetek)
Country or region

FRU No.

CRU ID

Argentina

145000599

145000589

145000596

145000585

145000600

145000598

145000592

145000595

145000591

145000587

145000590

145000586

145000597

• LINETEK LS15+H03VV-F+LP39 1 m
Australia, New Zealand
• LINETEK LS15+H03VV-F+LP-23A 1 m
Brazil
• LINETEK LS15 H03VV-F LP26A 1 m
CE
• LINETEK LP-34+H03VV-F + LS15 1 m
China
• LINETEK PC323+RVV300/300+LS15 1 m
Denmark
• LINETEK LS15+H03VV-F+LP-38 1 m
Indian
• LINETEK PE-361+ H05VV-F+ LS15 1 m
Israel
• LINETEK LS15+H03VV-F+LP-41 1 m
Italy
• LINETEK LS15+H03VV-F+PE-336 1 m
Japan
• LINETEK LS15+VCTF+LP-54 1 m
Korea
• LINETEK LS15+H05VV-F+LP-E04A 1 m
South Africa
• LINETEK LS15+H03VV-F+PE-364 1 m
Switzerland
• LINETEK LS15+H03VV-F+LP-37 1 m

Chapter 9. Parts list

Table 13. Parts list - 3-pin power cords (Linetek) (continued)
Country or region

FRU No.

CRU ID

Taiwan

145000588

145000593

145000594

Country or region

FRU No.

CRU ID

Argentina

145000567

145000557

145000564

145000553

145000568

145000566

145000560

145000563

145000559

145000555

145000558

145000554

145000565

145000556

• LINETEK LS15+VCTF+LP-53 1 m
U.K.
• LINETEK LP-61L+ H03VV-F+ LS15 1 m
UL
• LINETEK LP-30B + SPT-2 + LS15 1 m
Table 14. Parts list - 3-pin power cords (Longwell)

• Longwell LP-24+H03VV-F+LS-18 1 m
Australia, New Zealand
• Longwell LP-23A+LFC-3R+LS-18 1 m
Brazil
• Longwell LP-46+H03VV-F+LS-18 1 m
CE
• Longwell LP-34A+H03VV-F+LS-18 1 m
China
• Longwell LSG-31+RVV300/300+LS-18 1 m
Denmark
• Longwell LP-40+H03VV-F+LS-18 1 m
Indian
• Longwell LP-67+BIS+LS-18 1 m
Israel
• Longwell LP-41+H03VV-F+LS-18 1 m
Italy
• Longwell LP-22+H03VV-F+LS-18 1 m
Japan
• Longwell LP-54+VCTF+LS-18 1 m
Korea
• Longwell LP-486+KTLH03VV-F+LS-5 1 m
South Africa
• Longwell LP-39+H03VV-F+LS-18 1
Switzerland
• Longwell LP-37+H03VV-F+LS-18 1 m
Taiwan
• Longwell LP-71+VCTF+LS-33 1 m

Hardware Maintenance Manual

Table 14. Parts list - 3-pin power cords (Longwell) (continued)
Country or region

FRU No.

CRU ID

U.K.

145000561

145000562

Country or region

FRU No.

CRU ID

Argentina

145000528

145000532

145000527

145000525

145000538

145000534

145000536

145000526

145000535

145000530

145000533

145000529

145000524

145000531

145000605

145000537

• Longwell LP-61L+H03VV-F+LS-18 1 m
UL
• Longwell LP-30B+SPT-2 18AWG+LS-18 1 m
Table 15. Parts list - 3-pin power cords (Volex)

• VOLEX VA2073+H03VV-F+VAC5S 1 m
Australia, New Zealand
• VOLEX AU10S3+H03VV-F+VAC5S 1 m
Brazil
• VOLEX CH10S3+H03VV-F+VAC5S 1 m
CE
• VOLEX M2511+HO3VV-F+VAC5S 1 m
China
• VOLEX GB10S3+RVV 300/500+VAC5S 1 m
Denmark
• VOLEX MP233D+H03VV-F+VAC5S 1 m
Indian
• VOLEX IA6A3+IS694+VAC5S 1 m
Israel
• VOLEX SI16S3+H03VV-F+VAC5S 1 m
Italy
• VOLEX IT10S3+HO3VV-F+VAC5S 1 m
Japan
• VOLEX VAC5S+VCTF+M755 1 m
Korea
• VOLEX M2511+KETI IEC+VAC5S 1 m
South Africa
• VOLEX SA16A+HO3VV-F+VAC5S 1 m
Switzerland
• VOLEX MP232+H03VV-F+VAC5S 1 m
Taiwan
• VOLEX TW15CS3+VCTF+VAC5S 1 m
U.K.
• VOLEX MP5004+H03VV-F+VAC5S 1 m
UL
• Volex US15S3+SPT-2 ＋VAC5S 1 m

Chapter 9. Parts list

Table 16. Parts list - 2-pin power cords (Linetek)
Country or region

FRU No.

CRU ID

Africa

145500024

145500030

145500023

145500028

145500018

145500022

145500020

145500029

145500026

145500025

145500027

145500021

145500019

• LINETEK PE364("O")+H03VVH2-F+LS7H 1 m
Argentina
• LINETEK LP40+H03VVH2-F+LS7H 1 m
Australia
• LINETEK LP15A+H03VVH2-F+LS7 1 m
Brazil
• LINETEK LP25+H03VVH2-F+LS7H 1 m
CCC
• LINETEK PC205+RVV 0.75/2C+COC03 1 m
CE
• LINETEK LP21+H03VVH2-F+ LS7 1 m
India
• LINETEK LP28+IS:694 0.75/2C+ LS7H 1 m
Israel
• LINETEK LP45+H03VV-F+LS7 1 m
Japan
• LINETEK LP51A+HVCTFK 0.75/2C+LS7J 1 m
Korea
• LINETEK LPE03A+H03VVH2-F+LS7 1 m
Taiwan
• LINETEK LP51A+VCTFK 0.75/2C+LS7J 1 m
UL
• LINETEK LP5+SPT-2 #18/2C+ LS7C 1 m
UK
• LINETEK LP61L+H03VVH2-F+ LS7H 1 m

Hardware Maintenance Manual

Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply
to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.

Electronic emissions notices
For electronic emission information on Class B digital devices, refer to the corresponding information in
the User Guide.

Trademarks
The following terms are trademarks of Lenovo in the United States, other countries or both:
Lenovo
OneKey
Windows is the trademark of the Microsoft group of companies.
Intel is the trademark of Intel Corporation or its subsidiaries in the United States, other countries, or both.
Other company, product, or service names may be the trademarks or service marks of others.

Hardware Maintenance Manual

Part Number:

Printed in China

(1P) P/N:

*1P*

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Language                        : en
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Compression 0020level           : 6
Compression 0020type            : auto
Config 0020 File                : D:\ptc\Arbortext PE\lib\standard.pdfcf
EPS0020processor                : PStill version 1.74.14
Graphics 0020resolution         : 600
Graphics 0020resolution 0020threshold: 900
JPEG0020quality                 : 80
Create Date                     : 2012:09:19 17:19:30-07:00
Creator Tool                    : Arbortext 5.4
Modify Date                     : 2012:09:19 16:31:22+08:00
Metadata Date                   : 2012:09:19 16:31:22+08:00
Producer                        : PDFlib+PDI 7.0.4 (Win32)
Format                          : application/pdf
Document ID                     : uuid:3f44ed7b-fd0d-42cf-8397-d6590ee76809
Instance ID                     : uuid:e719a984-8d3c-450f-8523-e69eae7235e2
Page Layout                     : SinglePage
Page Count                      : 104
Compression Level               : 6
Compression Type                : auto
Config File                     : D:\ptc\Arbortext PE\lib\standard.pdfcf
Creator                         : Arbortext 5.4
EPS Processor                   : PStill version 1.74.14
Graphics Resolution             : 600
Graphics Resolution Threshold   : 900
JPEG Quality                    : 80

EXIF Metadata provided by EXIF.tools

Lenovo B580 Hmm En User Manual Hardware Maintenance Laptop (Lenovo) Type 4377

Navigation menu

Versions of this User Manual:

Views

Navigation