Leviton 47611-WG4 300Mbps Daul Band 802.11n Wireless Gigabit Router User Manual
Leviton Manufacturing Co., Inc. 300Mbps Daul Band 802.11n Wireless Gigabit Router
Leviton >
Contents
- 1. User Manual Part 1
- 2. User Manual Part 2
User Manual Part 1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2215470 |
| Application ID | DE/cQfmvUvHmhQFv7q2TzQ== |
| Document Description | User Manual Part 1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 204.73kB (2559157 bits) |
| Date Submitted | 2014-03-14 00:00:00 |
| Date Available | 2014-03-18 00:00:00 |
| Creation Date | 2014-03-14 18:00:36 |
| Producing Software | Acrobat Distiller 10.1.8 (Windows) |
| Document Lastmod | 2014-03-14 18:00:50 |
| Document Title | User Manual |
| Document Creator | Acrobat PDFMaker 10.1 Word 版 |
| Document Author: | monicac |
Copyright
Copyright ¤ 2014 by Leviton Manufacturing Co., Inc. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of LEVITON.
LEVITON makes no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose.
Any
software described in this manual is sold or licensed "as is". Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary
servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further,
this company reserves the right to revise this publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their
respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encourages to try to correct the interference
by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC and IC Statement:
To assure continued compliance, (example-use only shielded interface cables when connecting to computer or
peripheral devices) any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).
Operation is subject to the Following two conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference that may cause undesired
operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
II
Canadian Department of Communications
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la
conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la
conformité de rf.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to
avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna
shall not be less than 20 cm (8 inches) during normal operation.
The device in the 5150-5250 MHz band is for indoor use only.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal
Equipment and the mutual recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal
Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to
ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
User Manual for LEVITON 300Mbps Dual Band 802.11n Wireless Gigabit Router
Model: 47611-WG4
Rev: 1.3 (March, 2014)
III
CONTENTS
Chapter 1.Product Introduction........................................................................................................... 1
1.1
Package Contents ............................................................................................................... 1
1.2
Product Description............................................................................................................ 2
1.3
Product Features................................................................................................................. 5
1.4
Product Specification ......................................................................................................... 7
Chapter 2.Hardware Installation .......................................................................................................... 9
2.1
Hardware Description ......................................................................................................... 9
2.1.1
The Front Panel ......................................................................................................10
2.1.2
LED Indications.......................................................................................................10
2.1.3
The Rear Panel....................................................................................................... 11
2.1.4
The Right Side Panel..............................................................................................12
Chapter 3.Connecting to the Router .................................................................................................13
3.1
System Requirements ......................................................................................................13
3.2
Installing the Router..........................................................................................................13
Chapter 4.Quick Installation Guide ...................................................................................................15
4.1
4.2
Manual Network Setup - TCP/IP Configuration ..............................................................15
4.1.1
Obtain an IP Address Automatically........................................................................15
4.1.2
Configure the IP Address Manually ........................................................................17
Starting Setup in the Web UI ............................................................................................22
Chapter 5.Configuring the Router .....................................................................................................26
5.1
Device Info .........................................................................................................................26
5.2
Network ..............................................................................................................................31
5.3
5.4
5.2.1
LAN Settings...........................................................................................................31
5.2.2
WAN Settings..........................................................................................................32
5.2.3
DHCP Settings........................................................................................................39
5.2.4
WAN Port ................................................................................................................41
Security Settings...............................................................................................................44
5.3.1
Group Settings........................................................................................................44
5.3.2
Port Filter ................................................................................................................46
5.3.3
URL Filter................................................................................................................50
5.3.4
MAC Address Filter.................................................................................................53
5.3.5
WAN Access Control...............................................................................................55
Advanced Settings............................................................................................................57
5.4.1
Virtual Server ..........................................................................................................57
5.4.2
DMZ Settings ..........................................................................................................59
5.4.3
UPnP Settings ........................................................................................................60
5.4.4
Routing....................................................................................................................61
5.4.5
Bandwidth Control ..................................................................................................62
IV
5.5
5.6
Wireless Settings ..............................................................................................................65
5.5.1
Basic Settings .........................................................................................................65
5.5.2
Wireless Security ....................................................................................................68
5.5.3
WPS Settings..........................................................................................................71
5.5.4
WDS Settings .........................................................................................................73
5.5.5
Guest Network ........................................................................................................76
5.5.6
Wireless Access Control .........................................................................................77
5.5.7
Connection Status...................................................................................................79
5.5.8
Wireless –Advance Settings ...................................................................................79
USB Applications ..............................................................................................................81
5.6.1
USB Storage ...........................................................................................................81
5.6.2
Printing Service.......................................................................................................84
5.7
IPTV Settings ...................................................................................................................102
5.8
Tools .................................................................................................................................104
5.8.1
Time Settings ........................................................................................................104
5.8.2
Firmware Upgrade ................................................................................................105
5.8.3
Backup/Restore Settings ......................................................................................106
5.8.4
Restore to Factory Default Settings......................................................................106
5.8.5
Change Password/User Name .............................................................................107
5.8.6
Reboot ..................................................................................................................108
5.8.7
Statistics................................................................................................................109
5.8.8
Syslog ...................................................................................................................109
Chapter 6.Quick Connection to a Wireless Network ..................................................................... 111
6.1
Windows XP (Wireless Zero Configuration) ................................................................. 111
6.2
Windows 7 (WLAN AutoConfig)..................................................................................... 113
6.3
Mac OS X 10.x.................................................................................................................. 115
6.4
iPhone / iPod Touch / iPad ............................................................................................. 117
Appendix A: Leviton Smart Discovery Utility.................................................................................121
Appendix B: Troubleshooting..........................................................................................................122
Appendix C: Configuring the PC in Windows 7 .............................................................................124
Appendix D: Specifications..............................................................................................................128
Appendix E: Glossary.......................................................................................................................130
User Manual of 47611-WG4
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing LEVITON 47611-WG4. Before installing the router, please verify the contents inside the
package box.
47611-WG4 Wireless Router
Quick Installation Guide
CD-ROM
(User Manual included)
Power Adapter
Ethernet Cable
12V/1A DC output
100~240V AC input
Ethernet Cable
If there is any item missed or damaged, please contact the Leviton Tech
Support immediately.
-1-
User Manual of 47611-WG4
1.2 Product Description
2.4G & 5G Simultaneous Dual Band Wireless Connectivity
Since there are more and more wireless applications and electric devices using the radio frequency of 2.4GHz,
the wireless channel of 2.4GHz has been already too crowded for clients to enjoy the high-speed wireless
connection. In order to avoid the wireless interference between each other, LEVITON 47611-WG4 provides
users the radio frequency of 5GHz for watching HD videos or playing online games additionally. At the same
time, it enables other users still surf the Internet via the original radio frequency of 2.4 GHz. The 47611-WG4 is
just like 2 totally independent Access Points in one device for you.
-2-
User Manual of 47611-WG4
Multiple Network Technologies for Incredibly 600Mbps High-Speed Connection
The 47611-WG4 supports IEEE 802.11a/b/g/n Dual Band standard with 2T2R antenna technology, therefore it
can provide the wireless speed up to 300 + 300Mbps which is 12 times faster than that of traditional 11g Access
Point. Moreover, the 47611-WG4 is equipped with all Gigabit Ethernet Ports. Compared with general wireless
routers, the 47611-WG4 offers faster transmitting speed and more convenient method to enable or disable
wireless signal.
Fully Support of Wireless Security Encryption
To secure the wireless communication, the 47611-WG4 supports up-to-date encryption technology, WPA / WPA2
and WPA-PSK / WPA2-PSK with TKIP/AES. The 47611-WG4 supports Wi-Fi Protected Setup (WPS)
configuration with PBC/PIN methods to simplify the wireless security settings. By just clicking the WPS button,
the secure connection between the wireless AP and wireless client will be built immediately.
WPS (Wi-Fi Protected Setup)
Quick & Easy Wireless Connection
STEP.1
STEP.2
STEP.3
Connected
WPS
Press
Click
IPTV Pass-through for Video On Demand
The 47611-WG4 provides an IPTV-specific port which enables the IPTV Set-Top-Box (STB) connection directly
by passing through the LAN port. The IPTV feature makes it possible for users to enjoy online videos on the TV
set via Set-Top-Box (STB) through the 47611-WG4 while surfing Internet. The IPTV port can also function as a
LAN port if IPTV service is not enabled.
47611-WG4 IPTV Connection with IPTV Pass-though
A/V
Internet
Cable/xDSL
Modem
Set-Top Box
IPTV Port
TV
IPTV-Public IP
001101010
PC
Broadband Router
Game Console
LAN-Private IP
47611-WG4
100Base-TX UTP
1000Base-T UTP
A/V
-3-
Audio Line / Video Line
User Manual of 47611-WG4
More Flexible File Sharing over USB port
The 47611-WG4 is built-in with one USB 2.0 port which can be connected to a USB printer or storage device for
file sharing. It can recognize the USB printer or storage automatically without user experience. Thus, all clients
on the network can share printer or mass storage through the 47611-WG4 without complicated network
configuration. Via the USB port, it also can output 5V DC power to charge any USB compliant devices.
USB Port
or
Printer
USB
USB HDD
USB
* Sharing Printer and Mass Storage
Powerful Firewall and Complete Access Control Functions
The 47611-WG4 supports NAT function allowing multiple users to access Internet via a single legal IP. It also
provides Virtual Server for the specific LAN PC to act as an application server and offer certain service to the
clients on the Internet. In addition, the powerful firewall protects your Intranet clients from unauthorized accesses
and various kinds of DoS attacks from the Internet. In the aspect of firewall, the 47611-WG4 supplies IP-based
and MAC-based access control to prevent possible hackers attack.
Easy Setup for Multiple Wireless Modes
The 47611-WG4 supports multiple wireless modes including AP, Wireless Bridge, and Repeater, for different
network applications. Furthermore, with the built-in Quick Setup function, users can configure the 47611-WG4
easily and quickly through a couple of simple steps. It is so easy to apply the 47611-WG4 to the existing wired
network. The 47611-WG4 definitely provides a total network solution for the home and the SOHO users.
-4-
User Manual of 47611-WG4
Wireless AP Router Mode
WDS Bridge-PtP Mode
Internet
Smart Phone
Internet
WAN
001101010
001101010
Cable/xDSL
Modem
Cable/xDSL
Modem
47611-WG4
47611-WG4
Switch
AP
Clients
Laptop
WDS Repeater
WDS Bridge-PtMP Mode
Internet
AP
001101010
Switch
Internet
Clients
LAN
Laptop
Cable/xDSL
Modem 47611-WG4
AP
Switch
Laptop
Clients
47611-WG4
47611-WG4
AP/Client Link
Tablet
WDS Link
Wireless Coverage Plus !
The 47611-WG4 is equipped with 5dBi High-Gain antennas to provide strong signal and excellent performance
even in the long range or bad environment. Besides essential wireless sharing for Wi-Fi clients, the 47611-WG4
provides WDS (Wireless Distribution System) bridge mode to facilitate wireless network deployments and
range expanding. It provides more flexibility for users while establishing wireless network.
1.3 Product Features
¾ IEEE Compliant Wireless LAN & Wired LAN
Compliant with IEEE 802.11a/b/g/n dual-band (2.4G&5G) wireless technology capable up to
300+300Mbps data rate
Equipped with all Gigabit RJ-45 ports (10/100/1000Mbps) of 1 WAN and 4 LAN ports
Auto MDI/MDI-X supported
LAN4 supports IPTV Pass-through enables you enjoy online videos
¾ Fixed-network Broadband Router
Supported WAN connection types: Dynamic IP/ Static IP / PPPoE / PPTP / L2TP / PPPoE Dual
Access
Supports Dynamic DNS and DHCP Server
¾ Secure Network Connection
Supports Wi-Fi Protected Setup (WPS)
Advanced security: 64/128-bit WEP, WPA/WPA2 and WPA-PSK/WPA2-PSK (TKIP/AES
encryption)
Supports NAT firewall, IP / Port / URL-based access control and MAC address Filtering
-5-
User Manual of 47611-WG4
Support Dual-SSID to allow users to access different networks through a single AP
¾ Advanced Networking function for Specific Application
Supports Bandwidth Control (QoS) based on different local IP addresses
Supports NTP, Virtual Server, UPnP, and DMZ for various networking applications
Equipped with one USB port for sharing printers and USB mass storages wirelessly
¾ Easy Installation & Management
User Friendly Web-based UI with On-line Help
Remote Management allows configuration from a remote site
System status monitoring includes DHCP Client List and System Log
-6-
User Manual of 47611-WG4
1.4 Product Specification
Product
47611-WG4
300Mbps Dual-Band 802.11n Wireless Gigabit Router
Hardware Specification
WAN Port:
1 x 10/100/1000Mbps Auto MDI/MDI-X RJ45 port
LAN Port:
3 x 10/100/1000Mbps Auto MDI/MDI-X RJ45 ports (LAN1~3)
IPTV Port:
1 x 10/100/1000Mbps Auto MDI/MDI-X RJ45 port (LAN4)
USB Port :
USB 2.0, Type-A, 5V DC/0.5A Output
Gain:
2 x 5dBi fixed antenna
Orientation:
Omni-directional
Interface
Antenna
Reset / WPS button at rear panel
Reset / WPS Button
Press for about 7 seconds to reset the device to factory default.
Press for 1 second to activate WPS function.
PWR/SYS, WLAN (2.4G & 5G) x 2
WAN (Link & 1000Mbps) x 1
LED Indicators
LAN (Link & 1000Mbps) x 3
IPTV (Link & 1000Mbps) x 1
USB, WPS
Material
Plastic
Dimension (WxDxH)
171.61 x 111.16 x 25.47 mm (W x D x H)
Weight
8.81oz
Power Requirement
12V DC, 1A
Wireless interface Specification
Standard
Compliance with IEEE 802.11a/b/g/n
Simultaneous 2.4 GHz and 5 GHz
Frequency Band
2.4GHz: 2.412~2.484GHz
5GHz: 5.180~5.825GHz
Transmission
Indoor up to 100m
Distance
5GHz:
2.4GHz:
RF Power
11b: 17±1dBm
11a: 12±1.5dBm
(Intentional Radiator)
11g: 14.5±1.5dBm
11n: 12±1.5dBm
11n: 12.5±1.5dBm
Wireless Management Features
Wireless Modes
AP
WDS PtP
WDS PtMP
-7-
User Manual of 47611-WG4
Encryption Security
WEP (64/128-bit)
WPA-PSK (TKIP) / WPA2-PSK (AES)
WPA (TKIP) / WPA2 (AES)
Provide Wireless LAN ACL (Access Control List) filtering
Wireless Security
Wireless MAC address filtering
Support WPS (WIFI Protected Setup )
Support Dual-SSID (2.4G & 5G)
Wireless Advanced
AP Isolation: Enable it to isolate each connected wireless client.
Support 802.11e WMM (Wi-Fi Multimedia)
Max. Supported
Wire: 15
Clients
Wireless: 10
Router Features
Shares data and Internet access for users, supporting following internet
access:
Dynamic IP
Internet Connection
Static IP
Type
PPPoE
PPTP
L2TP
PPPoE Dual Access
NAT firewall
Built-in NAT server which supports Virtual Server, and DMZ
Firewall
Built-in firewall with IP address filtering, Port filtering, URL filtering, and MAC
address filtering
Routing Protocol
Static Routing
Built-in DHCP server supporting static IP address distributing
Support UPnP, Dynamic DNS
LAN
Support Packets Statistics
IP-based Bandwidth Control
Session Number: Max. 8000
Web-based (HTTP) management interface
Remote management (WAN Access Control)
System Management
SNTP time synchronize
System Log
Windows 7
OS Compatibility
Windows Vista
Windows XP
Mac OS X 10.4 and higher
-8-
User Manual of 47611-WG4
Chapter 2. Hardware Installation
Please follow the instructions below to connect 47611-WG4 to the existing network devices and your computers.
2.1 Hardware Description
Dimension: 171.61 x 111.16 x 25.47mm (W x D x H)
Diagram :
Figure 2-1
-9-
User Manual of 47611-WG4
2.1.1 The Front Panel
The front panel provides a simple interface monitoring the router. Figure 2-2 shows the front panel of
47611-WG4.
Front Panel
5GHz 2.4GHz
Power WPS
WAN USB
Figure 2-2 47611-WG4 Front Panel
2.1.2 LED Indications
The LEDs on the front panel indicate instant status of port links, wireless data activity, system power; and help
monitor and troubleshoot when needed. Figure 2-2 and Table 2-1 show the LED indications of the Wireless
Router.
LED Definition
Figure 2-3 47611-WG4 Front Panel
LED
(Left to Right)
PWR
STATE
FUNCTION
On
Device power on
Flash
The system is working properly
Off
Device power off
-10-
User Manual of 47611-WG4
Flash
WPS
The system is performing WPS authentication on a client
device.
On
The 5G WiFi is activated
Flash
Device is transmitting data wirelessly over 5GHz
On
The 2.4G WiFi is activated
Flash
Device is transmitting data wirelessly over 2.4GHz
On
Link is established
Flash
Packets are transmitting or receiving
Off
LAN port is not connected
On
Link is established
Flash
Packets are transmitting or receiving
Off
WAN port is not connected
On
The USB port is correctly connected
Off
The USB port is not connected
5G
2.4G
LAN
1~4
WAN
USB
Table 2-1 The LEDs indication
2.1.3 The Rear Panel
The rear panel provides the physical connectors connected to the power adapter and any other network devices.
Figure 2-3 shows the rear panel of 47611-WG4.
Rear Panel
5 dBi Antenna
4 x Gigabit LAN Ports
WAN Port IPTV/LAN4
WPS/Reset Power
Figure 2-4 Rear Panel of 47611-WG4
-11-
User Manual of 47611-WG4
Interface
Antenna x 2
Description
Fixed Dual-Band 5dBi Omni Dipole Antennas
Press the Reset button gently for 1 second and then release it. The
system starts to WPS connection.
WPS/Reset
Press the Reset button gently for 7 seconds and then release it. The
system restores to the factory default settings.
WAN
Connect to the Cable/xDSL Modem, or the Ethernet
LAN1-4
Connect to the user’s PC or network devices
Power
Connect to the power adapter provided in the package
Table 2-2 The Interface indication
2.1.4 The Right Side Panel
47611-WG4 built-in with one USB 2.0 port can be connected to a USB printer or storage for file sharing. The
USB port also output 5V DC power can charge any USB compliant devices.
Right Side Panel
USB Port
* Sharing Printer and Mass Storage
Figure 2-5 USB port of 47611-WG4
-12-
User Manual of 47611-WG4
Chapter 3. Connecting to the Router
3.1 System Requirements
Broadband Internet Access Service (Cable/xDSL/Ethernet connection)
One Cable/xDSL Modem that has an RJ-45 connector (not necessary if the Router is connected
directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ-45 connectors
PC of subscribers running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC OS 9 or
later, Linux, UNIX or other platform compatible with TCP/IP protocols
Above PC installed with WEB Browser
1. The Router in the following instructions means LEVITON 47611-WG4.
2. It is recommended to use Internet Explore 7.0 or above to access the Router.
3.2 Installing the Router
Before installing the Router, make sure your PC is connected to the Internet through the broadband service
successfully at this moment. If there is any problem, please contact your local ISP. After that, please install the
Router according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
Step 1. Power off your PC, Cable/xDSL Modem, and the Router.
Step 2. Locate an optimum location for the Router. The best place is usually at the center of your wireless
network.
Step 3. Adjust the direction of the antenna. Normally, upright is a good direction.
Step 4. Connect the power adapter to the power socket on the Router, and the other end into an electrical
outlet. Then power on the Router.
-13-
User Manual of 47611-WG4
Power
Power Adapter
Figure 3-1 Hardware Installation-1
Step 5. Follow the figure below to connect the network devices. It depends on your network environment to
connect the WAN port to a Cable/xDSL modem, or the Ethernet directly in your place.
Power
Power Adapter
USB Line
USB Storage
RJ-11
Phone
Jack
001101010
RJ-45
Cable /xDSL
Modem
PC/Laptop
RJ-45
A/V
TV
RJ-45
STB
Figure 3-2 Hardware Installation-2
-14-
User Manual of 47611-WG4
Chapter 4. Quick Installation Guide
This chapter will show you how to configure the basic functions of your Wireless Router using Quick Setup
within minutes.
A computer with wired Ethernet connection to the Wireless Router is required for the
first-time configuration.
4.1 Manual Network Setup - TCP/IP Configuration
The default IP address of the 47611-WG4 is 192.168.0.1. And the default Subnet Mask is 255.255.255.0. These
values can be changed as you desire. In this guide, we use all the default values for description.
Connect the local PC to the LAN ports of the Router. And then you can configure the IP address for your PC in
the following two ways.
Obtain an IP address automatically
Configure the IP address manually
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. And
the procedures in other operating systems are similar. First, make sure your Ethernet Adapter is working, and
refer to the Ethernet adapter’s manual if needed.
4.1.1 Obtain an IP Address Automatically
Summary:
1.
1.
Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
2.
Then the 47611-WG4 built-in DHCP server will assign IP address to the PC automatically.
Install TCP/IP component
1)
On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
2)
Click the Network and Internet Connections icon, and then click on the Network Connections tab in
the appearing window.
3)
Right click the icon shown below, select Properties on the prompt window.
-15-
User Manual of 47611-WG4
Figure 4-1
4)
In the prompt window shown below, double click on the Internet Protocol (TCP/IP).
Figure 4-2
5)
The following TCP/IP Properties window will display and the IP Address tab is open on this window
by default.
-16-
User Manual of 47611-WG4
2.
Setting IP address automatically
Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the
Figure below:
Figure 4-3
Now click OK to save your settings.
4.1.2 Configure the IP Address Manually
Summary:
Set up the TCP/IP Protocol for your PC.
Configure the network parameters. The IP address is 192.168.0.xxx ("xxx" is any number from 2 to
254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.0.1 (The Router's default IP address)
Select Use the following IP address radio button.
If the Router's LAN IP address is 192.168.0.1, enter IP address 192.168.0.x (x is from 2 to 254), and
Subnet mask 255.255.255.0.
Enter the Router’s LAN IP address (the default IP is 192.168.0.1) into the Default gateway field.
Select Use the following DNS server addresses radio button. In the Preferred DNS Server field, you can
enter the DNS server IP address which has been provided by your ISP
-17-
User Manual of 47611-WG4
Figure 4-4
Now click OK to save your settings.
Now, you can run the Ping command in the command prompt to verify the network connection between your
PC and the Router. The following example is in Windows XP OS. Please follow the steps below:
1.
Click on Start > Run.
-18-
User Manual of 47611-WG4
Figure 4-5
2.
In the run box type “cmd” and click OK. (Windows Vista users type “cmd” in the Start .Search box.)At the
prompt.
Figure 4-6
Open a command prompt, and type ping 192.168.0.1, and then press Enter.
If the result displayed is similar to Figure 4-7, it means the connection between your PC and the
Router has been established well.
-19-
User Manual of 47611-WG4
Figure 4-7 Success result of Ping command
If the result displayed is similar to Figure 4-8, it means the connection between your PC and the
Router has failed.
Figure 4-8 Failure result of Ping command
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some
firewall software programs may block a DHCP request on newly installed adapters.
-20-
User Manual of 47611-WG4
1. The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your
PC's adapter should be lit.
2. If the Router's IP address is 192.168.0.1, your PC's IP address must be within the
range of 192.168.0.2 ~ 192.168.0.254.
-21-
User Manual of 47611-WG4
4.2 Starting Setup in the Web UI
It is easy to configure and manage the 47611-WG4 with the web browser.
Step 1.
To access the configuration utility, open a web-browser and enter the default IP address
http://192.168.0.1 in the web address field of the browser.
Figure 4-9 Login the Router
After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case
letters. Then click the OK button or press the Enter key.
Figure 4-10 Login Window
Default IP Address: 192.168.0.1
Default User name: admin
Default Password: admin
-22-
User Manual of 47611-WG4
If the above screen does not pop up, it may mean that your web-browser has been set to a
proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that
appears, cancel the Using Proxy checkbox, and click OK to finish it.
After entering the username and password, the Easy Quick Setup page screen appears as Figure 4-11.
Figure 4-11 47611-WG4 Web UI Screenshot
Step 2.
Choose the correct Internet Access method. Please refer to the instructions in the next chapter for
configuring the other Broadband types.
-23-
User Manual of 47611-WG4
Figure 4-12 Choose Internet Access Method
Step 3. Please enter the User Name, Password and SSID security key and etc. Then click OK button to
make the configuration take effect immediately.
Figure 4-13
Step 4. For more detail network setting and functions configuration, you can click the Advanced button to
configure your Router.
-24-
User Manual of 47611-WG4
Figure 4-14
-25-
User Manual of 47611-WG4
Chapter 5. Configuring the Router
This chapter delivers a detailed presentation of router’s functionalities and features under 8 main menus below,
allowing you to manage the router with ease.
Figure 5-1
During operation, if you are not clear about a certain feature, you can simply click the “Help” button to read all
related helpful info.
5.1 Device Info
In this page, you can view information about the current running status of 47611-WG4, including WAN interface,
LAN interface, Wireless interface settings and status, and firmware version information.
WAN
-26-
User Manual of 47611-WG4
Figure 5-1-1
This section allows you to view the router’s WAN info listed below:
Object
Description
x WAN Status:
Displays WAN connection status: Disconnected, Connecting or
Connected.
x Disconnected:
Indicates that the Ethernet cable from your ISP side is / is not
correctly connected to the WAN port on the router or the router is not
logically connected to your ISP.
x Connecting:
Indicates that the WAN port is correctly connected and is requesting
an IP address from your ISP.
Connected: Indicates that the router has been connected to your
ISP.
x Internet
Connection Type:
Displays current Internet connection type.
x WAN IP:
Displays WAN IP address.
x Subnet Mask:
Displays WAN subnet mask.
x Gateway:
Displays WAN gateway address.
x DNS Server:
Displays WAN DNS address.
x WAN MAC
Address:
Displays router’s WAN MAC address.
x WAN Traffic:
Displays bandwidth currently used by router in KB/s.
x Connection
Duration:
Displays time duration indicating how long the router has been
connected to ISP.
x WAN Traffic Graph:
Displays a graphic presentation of the traffic flow.
-27-
User Manual of 47611-WG4
LAN
This section allows you to view the router’s LAN info listed below:
Figure 5-1-2 LAN Information
The page includes the following fields:
Object
Description
x IP Address:
Displays LAN IP address.
x Subnet Mask:
Displays LAN subnet mask.
x LAN MAC Address:
Displays router’s LAN MAC address.
x DHCP Server:
Displays whether DHCP server is enabled or not.
x NAT Entries/NAT:
Displays number of used NAT entries and MAX NAT entries.
Wireless
This section allows you to view the wireless info listed below:
-28-
User Manual of 47611-WG4
Figure 5-1-3 Wireless information
The page includes the following fields:
Object
Description
x Wireless Radio:
Displays whether wireless is enabled or not.
x Wireless MAC
Displays MAC address of the router’s wireless interface
address:
x SSID:
Displays current SSID.
x 802.11 Mode:
Displays currently active network mode.
x Country:
Displays current country.
x Channel:
Displays current channel.
x Security Mode:
Displays current security Mode.
System Info
This section displays CPU/memory usage, uptime, system time, number of connected client(s) and system
version info.
-29-
User Manual of 47611-WG4
Figure 5-1-4 General System information
The page includes the following fields:
Object
Description
x CPU Usage:
Displays current CPU usage status
x Memory Usage:
Displays current memory usage status.
x Up Time:
Displays uptime.
x Time:
Displays device’s time synchronized with Internet or manually
set by user.
x Connected
Displays the number of connected computers.
Client(s):
x Firmware Version:
Displays router’s firmware version.
-30-
User Manual of 47611-WG4
5.2 Network
“Network” includes the following four submenus. Clicking any of them enters corresponding interface for
configuration. Below explains, in details, each such feature.
Figure 5-2-1
5.2.1 LAN Settings
Figure 5-2-2 LAN settings web page screenshot
The page includes the following fields:
Object
Description
x IP Address:
Router’s LAN IP.
The default is 192.168.0.1. You can change it according to your
need.
x Subnet Mask:
Router’s LAN subnet mask.
If you change the device’s LAN IP address, you must enter the new one in your
browser to get back to the web-based configuration utility. And LAN PCs’ gateway
must be set to this new IP for successful Internet connection.
-31-
User Manual of 47611-WG4
5.2.2 WAN Settings
The screen below displays WAN connection status and interface info.
Figure 5-2-3
Click the “Config” button to enter WAN configuration interface. The router supports six Internet connection types,
include:
Dynamic IP
Static IP
L2TP
PPTP
PPPoE
PPPoE dual access
WAN IP, whether obtained automatically or specified manually, should NOT be on
the same IP net segment as the LAN IP, otherwise, the router will not work
properly. In case of emergency, press the hardware "Reset" button.
Dynamic IP (DHCP)
Select this option to let router obtain IP settings automatically from your ISP, if your ISP does not give you any IP
information or account information. You don’t need to configure any settings for this connection.
Figure 5-2-4
-32-
User Manual of 47611-WG4
The page includes the following fields:
Object
Description
x Internet
Displays a list of available Internet connection types
connection Type:
Maximum Transmission Unit.
x MTU:
The default value is1500.
DO NOT change the factory default MTU value unless necessary as an improper
MTU value may degrade your network performance or even lead to network
malfunction.
Static IP
If your ISP offers you static IP Internet connection type, select “Static IP" from corresponding drop-down menu
and then enter IP address, subnet mask, Primary DNS and secondary DNS information provided by your ISP in
corresponding fields.
Figure 5-2-5
The page includes the following fields:
Object
x Internet
connection Type:
x IP Address:
Description
Displays a list of available Internet connection types.
Enter the WAN IP address provided by your ISP. Inquire your ISP if
you are not clear.
-33-
User Manual of 47611-WG4
x Subnet Mask:
Enter WAN Subnet Mask provided by your ISP.
x Default Gateway:
Enter the WAN Gateway address provided by your ISP.
x Primary DNS
Enter the necessary DNS address provided by your ISP.
Server:
x Secondary DNS
Server:
Enter the other DNS address if your ISP provides you with 2 such
addresses, and it is optional.
Maximum Transmission Unit.
x MTU:
The default value is1500.
DO NOT change the factory default MTU value unless necessary as an improper
MTU value may degrade your network performance or even lead to network
malfunction.
PPPoE
Select PPPoE, if your ISP is using a PPPoE connection and provide you with PPPoE user name and password
info.
Figure 5-2-6
The page includes the following fields:
Object
Description
x Internet
Displays a list of available Internet connection types.
connection Type:
x User Name:
Enter the User Name provided by your ISP.
x Password:
Enter the password provided by your ISP.
x MTU:
Maximum Transmission Unit.
The default value is 1492.
-34-
User Manual of 47611-WG4
DO NOT change the factory default MTU value unless necessary as an improper
MTU value may degrade your network performance or even lead to network
malfunction.
PPTP
The PPTP protocol allows you to connect your router to a VPN server.
For example: A corporate branch and headquarter can use this connection type to implement mutual and
secure access to each other’s resources.
Figure 5-2-7
The page includes the following fields:
Object
Description
x Internet connection
Type:
Displays a list of available Internet connection types.
x PPTP Server IP:
Enter the IP address of a PPTP server.
x Username/Password:
Enter Username/Password defined by the PPTP server.
x Address mode:
Select “Dynamic” if you don’t get any IP info from the PPTP server
x IP Address:
side, otherwise select “Static”.
Enter the IP address provided by your ISP. Inquire your local ISP if
-35-
User Manual of 47611-WG4
you are not clear.
x Subnet mask:
Enter the subnet mask provided by your ISP.
x Default Gateway:
Enter the gateway provided by your ISP. Inquire your local ISP if you
x DNS Server:
Enter the necessary DNS address provided by your ISP.
x Secondary DNS
Server:
Enter the other DNS address if your ISP provides you with 2 such
x MTU:
are not clear.
addresses, and it is optional
Maximum Transmission Unit.
The default value is 1460
L2TP
The L2TP protocol allows you to connect your router to a L2TP server.
For example: A corporate branch and headquarter can use this connection type to implement mutual and
secure access to each other’s resources.
Figure 5-2-8
The page includes the following fields:
Object
x Internet connection
Description
Displays a list of available Internet connection types.
Type:
-36-
User Manual of 47611-WG4
x L2TP Server IP
Enter the IP address of a L2TP server.
Address:
x Username/Password:
Enter Username/Password defined by the L2TP server.
x Address mode:
Select “Dynamic” if you don’t get any IP info from the L2TP server
side, otherwise select “Static”.
x IP Address:
Enter the IP address provided by your ISP. Inquire your local ISP if
you are not clear.
x Subnet mask:
Enter the subnet mask provided by your ISP.
x Default Gateway:
Enter the gateway provided by your ISP. Inquire your local ISP if you
are not clear.
x DNS Server:
Enter the necessary DNS address provided by your ISP.
x Secondary DNS
Enter the other DNS address if your ISP provides you with 2 such
addresses, and it is optional
Server:
x MTU:
Maximum Transmission Unit.
The default value is 1458
PPPOE Dual Access
Figure 5-2-9
The page includes the following fields:
Object
Description
x Internet
connection Type:
Displays a list of available Internet connection types.
-37-
User Manual of 47611-WG4
x Username:
Enter the PPPOE account provided by your ISP.
x Password:
Enter the PPPOE password provided by your ISP.
x Address mode:
Select “Dynamic” if you don’t get any IP info from the L2TP server side,
otherwise select “Static”.
x IP Address:
Enter the IP address provided by your ISP. Inquire your local ISP if you
are not clear.
x Subnet mask:
Enter the subnet mask provided by your ISP.
x Default Gateway:
Enter the gateway provided by your ISP. Inquire your local ISP if you are
not clear.
x MTU:
Maximum Transmission Unit.
The default value is 1492
-38-
User Manual of 47611-WG4
5.2.3 DHCP Settings
“DHCP” includes 3 submenus: DHCP Server, Client List and Static Assignment. Clicking any of them enters
corresponding interface for configuration. Below explains, in details, each such feature.
The Dynamic Host Configuration Protocol (DHCP) is an automatic configuration protocol used on IP
networks. If you enable the built-in DHCP server on the device, it will automatically configure the TCP/IP settings
for all your LAN computers (including IP address, subnet mask, gateway and DNS etc), eliminating the need for
manual intervention. Just be sure to set such PCs to DHCP clients by selecting “Obtain an IP Address
Automatically” on each such PC. When you turn these PCs on, they will automatically load the proper TCP/IP
settings provided by the device DHCP server.
DHCP Server
Figure 5-2-10
The page includes the following fields:
Object
Description
x DHCP
Check or uncheck the box to enable or disable the device’s DHCP
Server-Enable:
server feature.
x Start IP Address:
Enter the starting IP address for the DHCP server’s IP assignment.
x End IP Address:
Enter the ending IP address for the DHCP server’s IP assignment.
The length of time for the IP address lease. Configuring a proper lease
x Lease Time:
time improves the efficiency for the DHCP server to reclaim disused IP
addresses.
x Primary DNS
Server:
Enter a DNS server address assigned to DHCP clients.
-39-
User Manual of 47611-WG4
x Secondary DNS
Enter the other DNS address assigned to DHCP clients (optional).
Server
To benefit from the DHCP server feature, you must set all LAN PCs to DHCP clients by selecting the “Obtain an
IP Address Automatically” radio buttons thereon.
DHCP Client List
This section displays a DHCP dynamic client list, which includes host name, IP address, MAC address and
lease time info.
Figure 5-2-11
The page includes the following fields:
Object
Description
x IP Address:
Displays IP address(es) that client(s) obtained from the DHCP server.
x MAC Address:
Displays MAC address of a given host.
x Host name:
Displays name of a given host (DHCP client)
x Lease Time:
Remaining time for a corresponding IP address lease.
Static Assignment
If you would like some devices on your network to always have fixed IP addresses, you can use this feature and
manually add a static DHCP assignment entry for each such device.
-40-
User Manual of 47611-WG4
For example: To have a PC at the MAC address of 00:aa:bb:11:22:33 always receive the same IP address of
192.168.0.200, simply enter the IP and MAC addresses in corresponding fields and click “Add” and then the
“Save” button as shown below.
Figure 5-2-12
The page includes the following fields:
Object
Description
x IP Address:
Enter the IP address for static DHCP assignment.
x MAC Address:
Enter the MAC address of a computer to always receive the same IP
address (the IP you just entered above).
x Add:
Click to add the current IP-MAC static assignment entry to the list
x Edit:
Click to change a given static assignment entry.
x Delete:
Click to remove an existing entry
5.2.4 WAN Port
“WAN Port” includes 2 submenus: MAC Clone, and Speed/Duplex. Clicking either tab enters corresponding
interface for configuration. Below explains, in details, each such feature.
Figure 5-2-13
-41-
User Manual of 47611-WG4
MAC Clone
This section allows you to set router’s WAN MAC address. You can either manually enter a MAC or copy your
PC’s MAC to the router.
Figure 5-2-14
The page includes the following fields:
Object
Description
x WAN MAC
Displays router's current WAN MAC address, you can manually change
Address:
x Restore to Factory
Default MAC:
x Clone MAC:
it.
Click it to restore router’s WAN MAC to factory default value.
Click to copy your PC’s MAC to router’s WAN MAC Address field.
Normally you don't need to change the default WAN MAC value. However, some ISP
may bind client PC’s MAC address for Internet connection authentication. In this
case, simply enter such MAC in the WAN MAC Address field or click the “Clone
MAC” button. Note that the WAN MAC address in running status interface will be
updated accordingly.
Do remember to reboot the router to activate the new WAN MAC. DO NOT use the
“Clone MAC” feature if your ISP does not bind your PC’s MAC.
-42-
User Manual of 47611-WG4
Speed/Duplex
This section allows you to config the router’s WAN port speed/duplex settings.
Figure 5-2-14
You can select a WAN port speed/duplex mode that best suit your network environment from the drop-down list,
which includes auto, 10M half-duplex, 10M full-duplex, 100M half-duplex, 100M full-duplex, 1000M half-duplex
and 1000M full-duplex.
The WAN port speed/duplex mode must match that of its link partner to achieve
successful communication; otherwise, the WAN port may not function properly. So, if
you are not sure about the link partner’s speed/duplex mode, please select “Auto”
-43-
User Manual of 47611-WG4
5.3 Security Settings
“Security Settings” includes the following 5 submenus. Clicking any of them enters corresponding interface for
configuration. Below explains, in details, each such feature.
5.3.1 Group Settings
“Group Settings” includes 2 submenus: Group Settings, User Group and Time Group. Clicking either tab
enters corresponding interface for configuration. Below explains, in details, each such feature.
User Group
To create a user group, you need to specify a group name/description and an IP address/range. The user group
feature works together with other related features.
Figure 5-3-1
For example: If you want to add a user group for a R&D department within an IP of
192.168.0.200-192.168.0.250, first click the “Add” button and then follow steps below:
-44-
User Manual of 47611-WG4
Figure 5-3-2
1.
Enter R_D in group name field.
2.
Enter R_D IP Range in group description field.
3.
Enter “192.168.0.200” and “192.168.0.250” in IP fields.
4.
Click “Add “and then the “Save “button; you will find
Such entry in User Group list below:
Figure 5-3-3
Time Group
To create a time group, you need to specify a group name/description and a time / time range.
-45-
User Manual of 47611-WG4
Figure 5-3-4
For example: If you want to set a period of time from 8Κ00 to 18Κ00 on working days from Monday to Friday
to a time group, first click the “Add” button and then follow steps below:
Figure 5-3-5
1.
Enter “Working days” in group name field.
2.
Enter “working days” in group description field.
3.
Select the time and days.
4.
Click “Save” and you will find such entry in Time Group list below:
Figure 5-3-6
5.3.2 Port Filter
To better manage PCs in LAN, you can allow or disallow such PCs to access certain ports on Internet using the
Port Filter functionality.
-46-
User Manual of 47611-WG4
Figure 5-3-7
Click “Add” to enter page below:
Figure 5-3-8
The page includes the following fields:
Object
Description
x Filter Mode:
Select Deny or Allow according to your own needs.
x Deny Access to
Disallow specified packets to pass through the router; other packets are
Internet:
x Allow Access to
Internet:
processed according to default rule.
Allow specified packets to pass through the router; other packets are
processed according to default rule.
x Enable:
Check to enable current filter entry.
x Description:
Enter a meaningful name to yourself for a new filter rule
-47-
User Manual of 47611-WG4
x User Group:
Select an added user group from the drop-down list.
x Time Group:
Select an added time group from the drop-down list.
x WAN Port Range:
x Protocol:
Enter port IDs. You can specify a range of ports or a single port.
Allowed port ID ranges from 1 to 65535.
Select a protocol or protocols for the traffic (“Both” includes TCP and
UDP).
For Example: If you want to disallow PCs within IP addresses ranging from 192.168.0.200 to
192.168.0.250(“R&D” user group) to access web sites from 8:00 to 18:00 on working days – from Monday to
Friday (“Working days” time group), do as follows:
1.
Select “Deny” from the filter mode drop-down list.
2.
Check the “Enable” box.
3.
Enter “Forbid websites” in description field.
4.
Select “R&D” from the user group drop-down list.
5.
Select “Working days” from time group drop-down list.
6.
Enter “80” in both boxes of “WAN Port Range”.
7.
Select “Both” from “Protocol” drop-down list.
Figure 5-3-9
8.
Click “Save” and you will find such entry in the List below.
-48-
User Manual of 47611-WG4
Figure 5-3-10
9.
Select “Allow” from the “Default” drop-down list and check “Enable” Port Filter feature.
Figure 5-3-11
-49-
User Manual of 47611-WG4
5.3.3 URL Filter
To better control LAN PCs, you can use the URL filter functionality to allow or disallow such PC to access certain
websites within a specified time range.
Figure 5-3-12
Click “Add” to display page below:
Figure 5-3-13
The page includes the following fields:
Object
Description
x Filter Mode:
Select Deny or Allow according to your own needs.
x Deny Access to
Disallow specified packets to pass through the router; other packets are
-50-
User Manual of 47611-WG4
Internet:
x Allow Access to
Internet:
processed according to default rule.
Allow specified packets to pass through the router; other packets are
processed according to default rule.
x User Group:
Select an added user group from drop-down list.
x Time Group:
Select an added time group from drop-down list.
x Description:
Enter a meaningful name to yourself for a new filter rule.
x URL character
Enter domain name string to be filtered.
string:
For Example: If you want to disallow PCs within IP addresses ranging from 192.168.0.200 to
192.168.0.250(“R_D” user group) to access only web sites containing “yahoo” from 8:00 to 18:00 on working
days – from Monday to Friday (“Working days” time group), without restricting other PCs, do as follows:
1.
Select “Deny” from the filter mode drop-down list.
2.
Check the “Enable” box.
3.
Enter “Disallow yahoo” in description field.
4.
Select “R_D” from the user group drop-down list.
5.
Select “Working days” from time group drop-down list.
6.
Enter “yahoo” in URL String field.
Figure 5-3-14
-51-
User Manual of 47611-WG4
7.
Click “Save” to display page below:
Figure 5-3-15
8.
Select “Allow” from the “Default” drop-down list and check the “Enable” URL Filter feature.
Figure 5-3-16
-52-
User Manual of 47611-WG4
5.3.4 MAC Address Filter
To better manage PCs in LAN, you can use the MAC Address Filter function to allow/disallow such PCs to
access to Internet.
Figure 5-3-17
Click “Add” to display page below:
Figure 5-3-18
The page includes the following fields:
Object
Description
x Filter Mode:
Select Deny or Allow according to your own needs.
x Deny Access to
Disallow specified packets to pass through the router; other packets are
Internet:
x Allow Access to
Internet:
x Description:
processed according to default rule.
Allow specified packets to pass through the router; other packets are
processed according to default rule.
Briefly describe a new filter rule
-53-
User Manual of 47611-WG4
x MAC:
x Time:
x Day:
Enter the computer’s MAC address that you want to filter out in the MAC
address field or select one from the MAC address list.
Select a time range for the new MAC address filter rule to take effect.
The default is 00:00-00:00, which means 24 hours.
Select a day or several days for the new MAC address filter rule to take
effect.
For Example: To only prevent a PC at the MAC address of 00:aa:bb:77:88:00 from accessing Internet from 8:00
to 18Κ00 everyday, without restricting other PCs, configure same settings on the screenshot below on your
device:
Figure 5-3-19
Click “Save” to display the following page. Select “Allow” from the “Default” drop-down list and check the
“Enable MAC Filter” feature as below.
Figure 5-3-20
-54-
User Manual of 47611-WG4
5.3.5 WAN Access Control
The WAN Access Control feature allows users to configure your router from Internet via a web browser.
Figure 5-3-21
The page includes the following fields:
Object
Description
x Enable:
Check or uncheck to enable or disable the WAN Access Control feature.
Enter a port ID for remote web-based management.
x Port:
The default is 8080.
x IP Address:
Enter the IP address of a PC on Internet authorized to access and
manage your router’s web-based utility remotely.
If you enter 0.0.0.0 in the IP address box, then all PCs on Internet can access your
router’s Web-based utility to view or change your settings remotely once you enable
the feature.
For example: If you want to allow only a PC at the IP address of 60.250.65.207 to access your router’s
Web-based utility from Internet via port: 8080, you need to configure same settings as shown on the interface
below on your router. And what this IP user needs to do is to simply launch a browser and enter http://
210.61.134.96:8080 (provided that your router’s WAN IP address is 210.61.134.96).
-55-
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : monicac Create Date : 2014:03:14 18:00:36+08:00 Modify Date : 2014:03:14 18:00:50+08:00 Subject : 300Mbps Dual Band 802.11n Wireless Gigabit Router XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2014:03:14 18:00:50+08:00 Creator Tool : Acrobat PDFMaker 10.1 Word 版 Format : application/pdf Title : User Manual Description : 300Mbps Dual Band 802.11n Wireless Gigabit Router Creator : monicac Document ID : uuid:1c929de1-0685-4faf-a8e0-c993825867be Instance ID : uuid:b5be0e5a-cdb5-44d2-bf05-2387b0676b5e Producer : Acrobat Distiller 10.1.8 (Windows) Page Count : 60EXIF Metadata provided by EXIF.tools