Leviton DDMX1 Remote Dimmer Switch User Manual 20161215 v1 11 11412386 Use Manuals

Leviton Manufacturing Co., Inc. Remote Dimmer Switch 20161215 v1 11 11412386 Use Manuals

Contents

User Manual_20161215_v1 - 11-11412386 - Use Manuals

PRELIMINARYSingle Pole (One location) or 3-Way (Multi-location)Fluorescent Digital DimmerCat. No. DD710-BD, 120/277V, 8A 960VA (120V), 5A 1385VA (277V) For use with fixtures using 0-10V dimmable power supply/drivers, Advance Transformer Mark 7®, OSRAM Sylvania QUICKTRONIC®, HeliosTM or equivalent dimmable ballastsINSTALLATION INSTRUCTIONSFor non-standard wiring applications, referto Wire Connector and Conductor Size Chart1 - #12 w/ 1 to 3 #14, #16 or #182 - #12 w/ 1 or 2 #16 or #181 - #14 w/ 1 to 4 #16 or #182 - #14 w/ 1 to 3 #16 or #18WIRE CONNECTOR / # OF COND.COMBINATION CHARTDI-000-DD710-02A-X0 Step 4b TOOLS NEEDED TO INSTALL YOUR DIMMERSlotted/Phillips Screwdriver Electrical Tape Pliers Pencil Cutters RulerIf installing Dimmer in a single device application, proceed with the INSTALLING YOUR DIMMER section. If installing Dimmer in a multi-device application, proceed as follows: INSTALLING DIMMER BY ITSELF OR WITH OTHER DEVICESChanging the color of your Dimmer:Your device may include color options. To change color of the face proceed as follows:12Insert top tabs and press in bottom tabs to attachPush in sides at bottom tabs and pull outward to releaseNOTE: For 3-Way applications, note that one of the screw terminals from the old switch being removed will usually be a different color (Black) or labeled Common. Tag that wire with electrical tape and identify as the common (Line or Load) in both the dimmer wall box and remote wall box.• Pull off pre-cut insulation from dimmer leads.• Make sure that the ends of the wires from the wall box are straight (cut if necessary).• Remove insulation from each wire in the wall box as shown.• For Single-Pole Application, go to Step 4a.• For 3-Way Matching Remote (w/LEDs) Application, go to Step 4b.INSTALLING YOUR DIMMERNOTE: Use check boxes when Steps are completed.ONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFONOFFWARNING: TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring! Step 1 Step 2Identifying your wiring application (most common):NOTE: If the wiring in your wall box does not resemble any of these configurations, consult an electrician.Single Pole1. Line (Hot)2. Neutral3. Ground4. Load5. Gray (-)6. Violet (+)3-Way1. Line or Load (see note below)2. Neutral3. Ground4. First Traveler – note color5. Second Traveler – note color6. Gray (-)7. Violet (+)Cut (if necessary)5/8" (1.6 cm) Strip Gage (measure bare wire here)Preparing and connecting wires:Pull off pre-cut insulation from dimmer leads. Make sure that the ends of the wires from the wall box are straight (cut if necessary). Remove insulation from each wire in the wall box as shown: Step 3Single Pole Wiring Application: Step 4aMAXIMUM BULB WATTAGE0-10VDC ballasts are rated in Volt-Amps (VA). The maximum number of ballast per dimmer is based on the load VA rating. The maximum bulb wattage is determined by the efficiency of the ballast. Ballast efficiencies will vary from different manufacturers; consider 80% efficient as average. Use the chart to determine maximum bulb wattage for typical ballast efficiency ratings. Use with Leviton's OPP20 Power Pack to increase the switch rating to 20 Amps for 120 and 277VAC ballast.MULTI-DEVICE APPLICATIONNOTE: No derating is required in multi-device applications.Remove all inner side sectionsDo not remove outer side sectionsBend back and forth to remove side sectionMAXIMUM BULB WATTAGE AT 75% EFFICIENCYMore than 2 Gang560WRating1000VASingle800WTwo Gang640W INTRODUCTIONThe next generation of lighting control technology is here with the new Decora® Digital Dimmer with Bluetooth® Technology. This innovative device works using the Leviton Decora® Digital Dimmer & Timer app that can be easily downloaded to smartphones or tablets and paired to the Leviton Dimmer using Bluetooth® technology. Decora® Digital Devices give users point-to-point local control to automate lighting, bridging the gap between standard dimmers and whole-house automation systems. The Decora® Digital Dimmer is a powerful device – combining the best of Leviton dimmer and timer functions with today’s mobile technology for impressive results. The simple touch of a finger following the intuitive on-screen guide makes it more convenient than ever to manage lighting for home activities or to ensure a "lived-in" look while away.Use of the app allows greater flexibility for accurate timer functionality and makes pushing buttons for timed events a tedious chore of the past.The Leviton Decora® Digital Dimmer & Timer app can be easily downloaded to mobile devices and is compatible with Android and iOS smartphones or tablets. The app is easy to use with simple, intuitive on-screen menu options to independently control dimmers and switches throughout the home.Decora® Digital Devices are ideal for living rooms, bedrooms, kitchens, dining rooms, home offices, outdoor lighting or anywhere full control of lighting is desired.Compatibility: Requires device with Bluetooth® 4.0 (BT LE) or later and iOS 6.0 and later. Compatible with iPhone, iPad, and iPod touch or Android 4.0 and later.• Soft fade ON/OFF• ON/OFF LED and Brightness level LED • Three way communication • Ease of installation – No new wiring FEATURESWARNINGS AND CAUTIONS:• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!• TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle, a motor- or a transformer-operated appliance. • To be installed and/or used in accordance with electrical codes and regulations.• If you are unsure about any part of these instructions, consult an electrician.• TO AVOID FIRE, SHOCK, OR DEATH; USE ONLY WITH appropriate LED 0-10V dimmable power supplies/drivers, Advance Transformer 120/277V Mark 7® 0-10V ballasts or OSRAM Sylvania QUICKTRONIC® or HeliosTM electronic ballasts.• The Decora® DD710 dimmer is not compatible with standard 3-way or 4-way switches. It must be used with a Decora® Digital remote for multi-location control, such as the DD00R-DL.WARNINGS AND CAUTIONS:• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.• Dimmer may feel warm to the touch during normal operation.• When retrofitting dimming ballasts into fixtures that originally had Instant Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and to prevent damage to the dimming ballast. Refer to the instructions provided with the ballast.• Recommended minimum wall box depth is 2-3/4".• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.3-Way Wiring with DD00R Matching Remote (w/LEDs) Application:321674532145632BlackDimmerLeadDimmerGreenDimmerLeadRedDimmerLeads1Gray (-)Dimmer Lead Violet (+)Dimmer Lead465Connect wires per WIRING DIAGRAM as follows:• Green or bare copper wall box wire to GREEN dimmer lead.• Line Hot wall box wire to BLACK dimmer lead.• Load wall box wire to RED dimmer lead.• Remaining RED Dimmer lead should have a label affixed. DO NOT REMOVE this label in a single pole application. NOTE: If the insulating label is not affixed to the second RED lead use electrical tape or a wire connector to cover.• Violet dimmer lead to (+) Violet connection on ballast. • Gray dimmer lead to (-) Gray connection on ballast. Proceed to Step 5.Wiring Diagram 1InsulatingLabelGreen GroundBlackRedHot (Black)Neutral (white)Line120/277VAC60HzDimmerViolet (+)Gray (-)YellowTo LampsRedBlue0-10 VDCBallastRed3223BlackScrew(common)3-WayBlackDimmerLeadDimmerGreenDimmerLeadRedDimmerLeads11Gray (-)Dimmer Lead Violet (+)Dimmer Lead454576Connect wires per WIRING DIAGRAM as follows:• Green or bare copper wall box wire to GREEN dimmer lead.• Common (Line hot or Load) wire to BLACK dimmer lead.• Remove insulating label and connect the first traveler wire to the RED dimmer lead.• Connect the second traveler wire to the remaining RED dimmer lead.• VIOLET dimmer lead to (+) Violet connection on ballast. • GRAY dimmer lead to (-) Gray connection on ballast. Proceed to Step 5.Wiring Diagram 2Green GroundBlackRedHot (Black)Neutral (white)Line120/277VAC60HzRedBlack Screw(common)3-WayDimmerViolet (+)Gray (-)Green GroundYellowTo LampsRedBlue0-10 VDCBallast

Navigation menu