Li Seng Technology SH-IOTML30BP IotT Module User Manual
Li Seng Technology Limited IotT Module
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3192266 |
| Application ID | j6+2Quymd+FJghp9upiLiw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 21.53kB (269166 bits) |
| Date Submitted | 2016-11-10 00:00:00 |
| Date Available | 2016-11-10 00:00:00 |
| Creation Date | 2016-11-04 04:18:07 |
| Producing Software | Mac OS X 10.12.1 Quartz PDFContext |
| Document Lastmod | 2016-11-08 16:41:02 |
| Document Title | Microsoft Word - IoT Module SH-IOTML3XBP-XX (R2.0).docx |
| Document Creator | Word |
IoT Module Model No: SH-IOTML3XBP-XX Rev 2.0 November 4, 2016 Page | 1 Living Smart 1. Description SH-IOTML3XBP module is a low cost, compact size, low power, high performance surface mount transceiver with 2.4GHz IEEE 802.15.4, Zigbee compliance, by using the high performance NXP JN5169 microcontroller. It is targeted for Smart Home Control customers. With this module, customers may develop their own Smart Home Device (like: lighting, door lock and home appliances) easily with provided SDK. It may work with Li Seng Gateway to achieve Smart Home Control features. 2. Features Modules General v 2.4GHz IEEE 802.15.4, Zigbee Light Link & Home Automation 1.2 Compatible v Lead-free and RoHS compliant • TX power +8.5dBm • Receive sensitivity -96dBm • TX current 21mA • RX current 13mA • 2.0V to 3.6V operation • 128-bit AES security processor • MAC accelerator with packet formatting, CRCs, address check, auto-acks, timers Microcontroller • 32-bit RISC CPU, up to 32MIPs with low power • Data EEPROM with guaranteed 100k write operations • ZigBee stacks • JTAG debug interface • 4-input 10-bit ADC, 1 comparator • 5 x PWM (4 x timer, 1 x timer/counter) • 2 UARTs • SPI Master & Slave port with 3 selects • 2-wire serial interface • Battery and Temperature Sensor • Watchdog timer and BOR • Up to 20 DIO Page | 2 Living Smart 3. Dimension and Pin Assignment a. Dimension: Fig 1. Dimension of the module Fig 2. Location of the pins Page | 3 Living Smart b. Pin Assignment: Pin No Pin Fucntions Primary Description Alternate Functions ADC1 DO0 SPICLK PWM2 Analogue to Digital Input SPI Master Clock Output or PWM2 Output DO1 SPIMISO PWM3 SPI Master In Slave Out Input or PWM3 Output DIO18 SPIMOSI DIO19 SPISEL0 DIO0 SPISEL1 ADC3 IO1 SPISEL2 ADC4 PC0 DIO2* RFRX TIM0CK_GT DIO3* RFTX TIM0CAP 10 DIO4 CTS0 JTAG_TCK TIM0OUT PC0 11 DIO5 RTS0 JTAG_TMS PWM1 PC1 12 DIO6 TXD0 JTAG_TDO PWM2 13 DIO7 RXD0 JTAG_TDI PWM3 14 DIO8 TIM0CK_GT PC1 PWM4 15 DIO9 TIM0CAP 32KXTALIN RXD1 16 DIO10 TIM0OUT 32KXTALOUT 17 VDD Supply Voltage 18 GND Digital Ground 19 DIO11 PWM1 20 DIO12 PWM2 CTS0 JTAG_TCK ADO or SPISMOSI DIO12, PWM2 Output, UART 0 Clear To Send Input, JTAG CLK Input, Antenna Diversity Odd Output or SPI Slave Master Out Slave In Input 21 DIO13 PWM3 RTS0 JTAG_TMS ADE or SPISMISO DIO13, PWM3 Output, UART 0 Request To Send Output, JTAG Mode Select Input, Antenna Diversity Even output or SPI Slave Master In Slave Out Output 22 RESETN SPI Master Out Slave In Output SPI Master Select Output 0 DIO0, SPI Master Select Output 1 or ADC input 3 DIO1, SPI Master Select Output 2, ADC input 4 or Pulse Counter 0 Input DIO2, Radio Receive Control Output or Timer0 Clock/Gate Input DIO3, Radio Transmit Control Output or Timer0 Capture Input DIO4, UART 0 Clear To Send Input, JTAG CLK Input, Timer0 PWM Output, or Pulse Counter 0 input DIO5, UART 0 Request To Send Output, JTAG Mode Select Input, PWM1 Output or Pulse Counter 1 Input DIO6, UART 0 Transmit Data Output, JTAG Data Output or PWM2 Output DIO7, UART 0 Receive Data Input, JTAG Data Input or PWM 3 Output DIO8, Timer0 Clock/Gate Input, Pulse Counter1 Input or PWM 4 Output 32KIN DIO9, Timer0 Capture Input, 32K External Crystal Input, UART 1 Receive Data Input or 32K external clock Input DIO10, Timer0 PWM Output or 32K External Crystal Output TXD1 DIO11, PWM1 Output or UART 1 Transmit Data Output Reset input 23 DIO14 SIF_CLK TXD0 TXD1 JTAG_TDO SPISEL1 or SPISSEL 24 DIO15 SIF_D RXD0 RXD1 JTAG_TDI SPISEL2 25 DIO16 COMP1P SIF_CLK SPISMOSI 26 DIO17 COMP1M PWM4 I2C DATA 27 VREF/AD C2 SPISIMO DIO14, Serial Interface Clock UART 0 Transmit Data Output, UART 1 Transmit Data Output, JTAG Data Output, SPI Master Select Output 1 or SPI Slave Select Input DIO15, Serial Interface Data or Intelligent Peripheral Data Out DIO16, Comparator Positive Input, Serial Interface clock or SPI Slave Master Out Slave In Input DIO17, Comparator Negative Input, Serial Interface Data or SPI Slave Master In Slave Out Output Analogue peripheral reference voltage or ADC input 2 Page | 4 Living Smart 4. Electrical Characteristics (Module) Typical DC Characteristics Deep Sleep current Sleep current Radio transmit current Radio receive current Centre frequency accuracy 50nA 0.7µA 21mA 13mA +/-25ppm Supply voltage Operating Temperature 2.0 to 3.6V -40°C to +125°C Notes With active sleep timer CPU in doze, radio transmitting @8.5dBm CPU in doze, radio receiving @0dBm Additional +/-15ppm allowance for temperature and ageing Standard range Typical RF Characteristics Frequency range Receive sensitivity Transmit power Maximum receiver input power RSSI range RF Port impedance – uFL connector Rx Spurious Emissions Tx Spurious Emissions Notes 2.4 to 2.485GHz -95dBm 8.5dBm 9dBm -4 to +4 dB 50 ohm Nominal for 1% PER, as per 802.15.4 Normal 1% PER, measured as sensitivity, supply current at 14.7 mA -95 dBm to -10 dBm 2.4 - 2.485GHz -70dBm -65dBm Measured conducted into 50ohms Measured conducted into 50ohms Peripherals Master SPI port Slave SPI port Two UARTs Two-wire serial I/F (compatible with SMbus & I C) 5 x PWM (4 x timer, 1 x timer/counter) Two programmable Sleep Timers Digital IO lines (multiplexed with UARTs, timers and SPI selects) 6 channel Analogue-toDigital converter Programmable analogue comparators Notes 3 selects Available Available Available Up to 16MHz Up to 8MHz 16550 compatible Up to 400kHz Available 16MHz clock Available 32kHz clock 20 Available 10-bit, up to 100ks/s Available Ultra low power mode for sleep Antenna Specification (*For Reference Only) Antenna plate Antenna gain Frequency range POWER Connector type FPC antenna 2dBi 2.4GHZ-2.483GHZ 0dBm External antenna Page | 5 Living Smart (*1) ●Ordering Information SH-IOTML①②③P-④⑤ Designator Item ① Communication Format ② Light Bulb drive channels ③ Version Number ④ Antenna Option ⑤ Output protocol Symbol -I -L Description Jennet-IP Format Zigbee Format Single Color Light Dual color Light RGBW color Light (TBD) JN5168 Version JN5169 Version External Antenna model Internal PCB Antenna model Internal PA, External Antenna model Jennet-IP protocol Zigbee Light Link protocol Zigbee Home Automation 1.2 protocol CC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The module is designed to comply with the FCC statement. FCC ID is RR3-SH-IOTML30BP. The host system using this modular should have label indicated it contain modular’s FCC ID RR3-SH-IOTML30BP. This radio module must not installed to co-locate and operating simultaneously with other radios in host system, additional testing and equipment authorization may be required to operating simultaneously with other radio.” Page | 6 Living Smart
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2016:11:04 04:18:07Z Creator : Word Modify Date : 2016:11:08 16:41:02+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : Word Metadata Date : 2016:11:08 16:41:02+08:00 Producer : Mac OS X 10.12.1 Quartz PDFContext Format : application/pdf Title : Microsoft Word - IoT Module SH-IOTML3XBP-XX (R2.0).docx Document ID : uuid:59080761-3f44-449a-a6d0-66fd5f0e9d8c Instance ID : uuid:032a6ef8-38de-4ee2-918a-d2aced632f55 Page Count : 6EXIF Metadata provided by EXIF.tools