Liebert Power Supply 350 Users Manual

350 to the manual 70717a75-7a20-4f2a-a34f-8c432c308e64

: Liebert Liebert-Liebert-Power-Supply-350-Users-Manual-571381 liebert-liebert-power-supply-350-users-manual-571381 liebert pdf

Open the PDF directly: View PDF .
Page Count: 2

PowerSure™ PSA

Quick-Start Guide for 350-1000VA; 120V

WHAT’S IN THE BOX

• Quick-Start guide

• PowerSure family user manual on CD (also at www.liebert.com)

• Warranty card

• MultiLink™ software CD

• MultiLink serial cable (M3LS9P9S), 10 ft. (3m)

• RJ-11 cord, 7 ft. (2.1 m)

• USB cable, 6 ft. (1.8m)

For more details, refer to the PowerSure user manual on CD.

Para una información más detallada, consulte el manual del usuario

de la familia PowerSure en el CD.

PowerSure PSA

* Power ON/OFF/

Alarm Silence

* Fault Indicator

(Red/Green)

* Utility Indicator

(Green)

Battery Indicator *

(Green/Amber)

DIP switches **

*** USB port

*** DB-9 port

Site Wiring Fault *

Indicator (Red)

** Orange output recep-

tacles (battery backup

and surge protection)

(4 receptacles on 350,

500 and 650VA models)

** Black output

receptacles (surge

protection only)

6-ft. (1.8m)

power cord

Battery cover plate

(on bottom for

650&1000 VA models)

(on rear of 350&500VA

models)

Data Line ***

Protection

Connectors

For details, see :

* Controls and Indicators

** Installation

*** Communications

INSTALLATION

Read all safety, installation and operating instructions in the PowerSure family user manual on the included CD or

at www.liebert.com before operating the UPS. Adhere to all warnings on the unit and in the manual.

1. Install the UPS indoors in a controlled environment, where it cannot be accidentally turned off. Place it in an area

of unrestricted airflow around the unit, away from water, flammable liquids, gases, corrosives and conductive

contaminants. Maintain a minimum clearance of 4 inches (100mm) on each side of the UPS. Maintain an ambi-

ent temperature range of 32°F to 104°F (0°C to 40°C).

2. Plug the PSA’s power cord into an AC outlet. Check the Site Wiring Fault Indicator on the rear; if it is illuminated,

refer to the Troubleshooting section.

3. Plug any computers and monitors into the orange receptacles for battery backup and surge protection; other

office machines that do not exceed the capacity of the UPS may be plugged into either of the two (2) black

receptacles, which provide surge protection only.

4. Connect Phone/Fax/DSL/Internet/Modem devices to data line connectors.

5. Press and release the ON/OFF/Alarm Silence button to turn on the UPS. The UPS will beep and the Utility Indi-

cator will illuminate (green).

6. Turn on connected equipment.

Plug this type of equipment into

black receptacles ONLY

Plug computers, monitors & network hubs

into orange receptacles

Inkjet printers Scanners Fax machines

COMMUNICATIONS

The PowerSure PSA will communicate with your computer in either of two ways: over its DB-9 port through Lie-

bert’s MultiLink™ software or by USB through Microsoft® Windows® operating system features.

MultiLink supplies useful monitoring data, such as input voltage and battery level, and will perform an orderly shut-

down of the computer system. Microsoft Windows XP and 2000 operating system utilities supply UPS status infor-

mation and will perform an orderly computer shutdown. Check your computer’s OS features to determine whether

it has power management capability.

For MultiLink Serial Communications

• Connect the provided MultiLink serial cable to the DB-9 ports on the rear of the UPS and on the rear of your

computer.

• Install the MultiLink software—the software, installation instructions and the user manual are on the CD included

in the PowerSure PSA package.

For USB Communications (with operating system power management)

• Connect the USB cable provided with the UPS to the USB ports on the PSA and your computer. The PSA will

work automatically with the built-in power management software on Windows XP and 2000 or later.

• All USB models are compatible with Microsoft Windows 2000, Windows XP and Macintosh® OS 10.2 or later.

CONTROLS AND INDICATORS

This button controls output power to the connected

load and has three functions:

• Turns the PowerSure PSA ON

• Turns the PowerSure PSA OFF

• Silences PowerSure PSA alarms

TURN THE UPS ON: Press and release the main ON/OFF

button to start the UPS. An audible alarm will sound briefly.

TURN THE UPS OFF: When the PSA is ON, hold the main

ON/OFF button down for more than 2 seconds to shut it down.

An audible alarm will sound briefly.

SILENCE AN ALARM: When a UPS alarm is active, press and

release the main ON/OFF button to silence the audible alarm

(Exceptions: low battery, overload and overtemperature). DO

NOT hold the button down for more than 2 seconds or the PSA

will shut down.

CHECK THE PSA’S CONDITION: Three status indicators on

the front of the UPS illuminate to specify the status of the UPS

(see Troubleshooting section for details).

SITE WIRING FAULT INDICATOR (RED)

The Site Wiring Fault Indi-

cator on the rear panel, as

shown, illuminates red

when the UPS detects a

line-neutral reversal or a

poor neutral-ground. (See

Troubleshooting Chart if

indicator is illuminated.)

TRANSFER VOLTAGE SELECTORS (DIP SWITCHES)

The two-position DIP switch control on the rear panel, shown

above, allows the operator to select the utility transfer voltage

at which the UPS will switch to battery power. The factory

default settings are 100VAC - 135VAC. DIP switch positions for

each voltage setting are:

DIP switch settings

Left Right Nominal Utility Setting

↑ Up ↑ Up 120VAC 85 - 145VAC (default)

↑ Up ↓ Down 110VAC 78 - 138VAC

↓ Down ↑ Up 127VAC 90 - 150VAC

↓ Down ↓ Down 120VAC 85 - 145VAC

!

CAUTION

Never change the voltage settings while the UPS

is ON and powering connected loads. Change

DIP switches only when the UPS is OFF.

!

CAUTION

To ensure protection of the connected

equipment, the DIP switch settings should match

the nominal utility input voltage. DIP switch

settings not matching the nominal utility could

potentially damage connected equipment.

Fault Indicator

Green: Overload/

Overtemperature

Red: UPS fault

Utility Indicator

Green: Normal operation

Amber: Buck/Boost

mode

Battery Indicator

Green: On battery

Amber: Battery

warning

DIP Switches

Site Wiring

Fault

Indicator

(Red)

Rear of UPS

SPECIFICATIONS

Model Number PSA350MT-120 PSA500MT-120 PSA650MT-120 PSA1000MT-120

Power Rating VA/W 350VA/210W 500VA /300W 650VA/ 390 W 1000 VA/600W

DIMENSIONS: in. (mm)

Unit

WxDxH

4.6x7.7x8.7

(116 x 196x222)

4.6x7.7x 8.7

(116x196x222)

4.6x14.1x8.7

(116 x358x222)

4.6x14.1x8.7

(116 x358x222)

Shipping

WxDxH

7.7x12.2x11.5

(196x310x 293)

7.7x12.2x11.5

(196x310x 293)

9.5x19.7x12.4

(242x500 x316)

9.5x19.7x12.4

(242x500x316)

WEIGHT: lbs (kg)

Unit 16.8 (7.6) 17.2 (7.8) 20.7 (9.4) 29.7 (13.5)

Shipping 18.1 (8.2) 18.5 (8.4) 22.9 (10.4) 31.9 (14.5)

INPUT AC PARAMETERS

Surge Protection 570J

Voltage Range Without

Battery Operation

78VAC - 150VAC, DIP switch selectable

(see “DIP switch settings” on page 1)

Frequency Range 46.5 - 63.5 Hz (±0.1 Hz)

Input Power Cord 6 ft. (1.8m) attached, w/ NEMA 5-15 P

OUTPUT AC PARAMETERS

Output Receptacles

(4) NEMA 5-15R (orange)

Battery backup + surge protection;

(2) NEMA 5-15R (black)

Surge protection

(6) NEMA 5-15R

(orange) Battery

backup + surge

protection;

(2) NEMA 5-15R

(black) Surge

protection

Voltage (Normal mode) Nominal (110, 120, 127VAC) ±10%

Voltage (Battery mode) 120VAC ±8%

Output Current 2.9 A 4.2 A 5.4 A 8.3 A

Waveform (Battery mode) Stepped Sinewave

Frequency 50 Hz or 60 Hz; auto sensing

Overload Warning

(Normal & Battery modes) >100%

Overload Shutdown >110%

BATTERY PARAMETERS

Type Valve-regulated, nonspillable, lead acid

QuantityxVoltagexRating (1)x12Vx7Ah (1)x12Vx9Ah (1)x12Vx9Ah (2)x12Vx7.5Ah

Transfer Time 4 - 6 ms typical

Backup Time: At 77°F (25°C), resistive loading, with fully charged batteries:

Full Load 8 minutes 8 minutes 5 minutes 5 minutes

Half Load 26 minutes 24 minutes 16 minutes 18 minutes

Recharge Time 6 hours to 90% of rated capacity,

after full discharge into resistive load

ENVIRONMENTAL (ALL MODELS)

Operating

Temperature

+32°F to +104°F

(0°C to +40°C)

Storage

Temperature

+5°F to +104°F

(-15°C to +40°C)

Relative

Humidity

0% to 95%, non-

condensing

Operating

Elevation

Up to 10,000 ft.

(3000m) at 86°F (30°C)

without derating

Audible Noise < 40 dBA, at 1 meter

AGENCY

Safety UL 1778, c-UL Listed

Surge

ANSI C62.41, Category

A, Level 3

(IEEE 587, Category A);

EN61000-4-5, Level 3,

Criteria A

ESD EN61000-4-2, Level 3,

Criteria A

Susceptibility EN61000-4-3, Level 3,

Criteria A

Electrical Fast

Transient/Burst

EN61000-4-4, Level 4,

Criteria A

Emissions FCC Part 15, Subpart B,

Class B

Conducted

Immunity

EN61000-4-6, Level 3,

Criteria A

Harmonics EN61000-3-2

Flicker EN61000-3-3

Transportation ISTA Procedure 1A

DISCONTINUED

PRODUCT

SL-23270QS (9/03) Rev. 0

TROUBLESHOOTING

The information below indicates various symptoms a user may encounter in the event

the PowerSure PSA experiences a problem.

Use this information to determine whether external factors caused the problem. See

Troubleshooting Chart for suggested remedy.

GUIDE TO STATUS INDICATORS

1. The Fault indicator illuminates, indicating the UPS

detected a problem.

2. An alarm sounds, alerting that the UPS requires

attention. The alarm can be silenced except for low

battery, overload and overtemperature warning

conditions.

3. Utility and/or Battery indicators may be illuminated as

a diagnostic aid to the operator, as shown below:

Fault

Indicator

Utility

Indicator

Battery

Indicator Diagnosis/

Audible Alarm

—Green

ON —Normal operation with utility power

present; no beep.

—— Green

ON

UPS is operating on battery; beep

every 10 seconds.

—— Green

ON

Battery test has been initiated; no

beep.

—Green

ON

Amber

Flashing

Battery needs to be replaced; long

beep every minute.

—— Amber

Flashing

Low battery warning; beep every

half-second.

Green

Flashing

Green

ON —Overload warning, load is >100%;

beep every half-second.

Green

Flashing ——

Overload shutdown, load exceeds

UPS capacity (110%); continuous

beep.

Green

ON

Green

ON —

Overtemperature (overtemp)

warning; beep every 5 seconds

(Normal mode).

Green

ON —Green

ON

Overtemperature (overtemp)

warning; beep every 5 seconds

(Battery mode).

Green

ON ——

Overtemperature (overtemp)

shutdown; long beep every

5 seconds.

Red

Flashing

Green

ON —UPS is on, fault warning;

continuous beep.

Red

ON —— UPS has failed & shut down;

continuous beep.

Fault

Indicator

Utility

Indicator

Battery

Indicator

MAINTENANCE

The PowerSure PSA UPS requires very little maintenance. Follow these practices to

prevent problems.

CLEANING THE UPS

The following will help ensure trouble-free operation for years:

• Vacuum dust from the ventilation intake occasionally.

• Wipe the cover periodically with a dry cloth.

MAINTAINING BATTERIES

The batteries are valve-regulated, nonspillable, lead acid and must be kept charged to

retain their design life. The UPS continuously charges the batteries when connected to

the utility supply, even while the UPS is switched off.

When storing the UPS, it is recommended to plug in the UPS for at least 24 hours every

four to six months to ensure full recharge of the batteries.

BATTERY REPLACEMENT

This UPS is equipped with internal “hot swappable” batteries that the user can replace

without shutting down the UPS or connected loads.

!

CAUTION

A battery can present a risk of electrical shock and high short circuit

current. The following precautions should be observed before replacing

the batteries:

• Remove rings, watches, and other metal objects.

• Do not lay tools or other metal objects on top of the batteries.

• If the battery replacement kit is damaged in any way or shows signs

of leakage, contact your local dealer or Liebert representative imme-

diately.

• Do not dispose of batteries in a fire. The batteries may explode.

• Dispose of old batteries according to local codes.

NOTE

Caution should be exercised when replacing the batteries because the

load is unprotected from disturbances and power outages during this

procedure.

TROUBLESHOOTING CHART

If the UPS fails to operate properly, turn off the unit and repeat the steps in the Installa-

tion section of this manual. If the problem persists, refer to the chart below:

Problem Cause Solution

UPS

will

not

start

Overload/Short

Circuit

Check the circuit protector on the rear of the

UPS. If it is tripped, reset it and restart the

UPS.

For further help, call your local dealer,

Liebert representative or the Liebert

Worldwide Support Group.

Battery disconnected

or is completely

discharged

Check for proper connection of battery or

batteries.

UPS starts

on battery,

but will

not switch

to AC

UPS not plugged in Plug in the power cord securely.

Circuit protector

tripped

Reset the circuit protector and restart the

UPS.

Power not available

at utility receptacle

Have the utility checked by a qualified

electrician.

Input voltage

below threshold

Wait until the voltage rises to an appropriate

level or have the utility checked by a

qualified electrician.

AC overvoltage

Wait until voltage lowers to an appropriate

level or have the utility checked by a

qualified electrician.

UPS

shuts

down,

Fault

Indicator

lit

Overload/Short

Circuit

Check the circuit protector on the rear of the

UPS. If it is tripped, reset it and restart the

UPS.

If the problem persists, disconnect some of

the equipment from your UPS—the total

wattage of your equipment must not exceed

the capacity of the UPS.

For further help, call your local dealer,

Liebert representative or the Liebert

Worldwide Support Group.

Internal UPS fault

High temp shutdown

Make sure that the UPS is operating in 32°F

to 104°F (0°C to 40°C) and that it has

adequate ventilation.

MultiLink shutdown Consult the MultiLink user manual or contact

your LAN administrator.

Site Wiring

Fault

Indicator

illuminated

Line-neutral

reversal,

Poor ground

connection

Have the utility checked by a qualified

electrician.

UPS not

providing

expected

back-up

time

Overload Reduce load.

Battery not charged

due to a recent

outage

Recharge battery.

Battery needs to be

replaced Replace battery.

PRODUCT WARRANTY REGISTRATION

To register for warranty protection:

• Visit the Quick Links section of our

Web site at:

http://www.liebert.com

• Click on Product Warranty

Registration and fill in the form.

If you have any questions, please

contact us at:

US: 800-222-5877

Outside the US: 614-841-6755

upstech@liebert.com

BATTERY REPLACEMENT

Replacement requires removing the battery cover plate on the bottom of the UPS. No

tools are needed.

To replace the batteries:

1. Remove the battery

cover plate on the

back/bottom of the

UPS (Figure 1).

2. Pull the white tabs

towards you to

remove the battery

from the UPS

(Figure 2).

Figure 1 Figure 2

3. Disconnect the insu-

lated connectors

from the battery ter-

minals (Figure 3).

4. Insert a new battery

pack, and push the

connectors onto the

battery terminals

(black to black & red

to red) (Figure 4).

Figure 3 Figure 4

NOTE: There may be a small spark at the battery terminals when reconnecting

the connectors. This is normal and will not harm you or the UPS.

5. Push the battery

pack into the UPS

(Figure 5).

6. Reattach the battery

cover plate

(Figure 6).

Figure 5 Figure 6

DISCONTINUED

PRO D UC T