Lifeline Systems AT410 Smoke Detector Transmitter User Manual AT410 install

Lifeline Systems Inc Smoke Detector Transmitter AT410 install

User guide

1User and Installation GuideLifeline® Systems AT410
2 Copyright and DisclaimerCopyright © 2004 Lifeline Systems, Inc. All rights reserved.Proprietary MaterialThe information furnished in this document is proprietary to Lifeline Systems Inc. (Lifeline) and is considered privileged and confidential.TrademarksLifeline®, CarePartner® Communicator, and AutoLearn® are registered trademarks of Lifeline Systems Inc. VoiceAssist™, VoiceClock™, TelAssure™, Classic Pendant™, and Slimline™ Personal Help Button are trademarks of Lifeline Systems Inc. All brand names and product names used in this manual are trademarks, registered trademarks or trade names of their respective holders.Limit of LiabilityThe publisher has used their best efforts in preparing this manual. Lifeline Systems Inc. makes no representation or warranty with respect to the accuracy or completeness of the contents of this manual and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose and shall in no event be liable for any loss of profit or any other commercial damage including but not limited to special, incidental, consequential, or other damages.How to Contact Lifeline Systems:111 Lawrence StreetFramingham, MA 01702-8156(508) 988-1000 or (800) 380-3111http://www.lifelinesystems.com
Changing the Battery in the AT410 3Chapter 1:AT410 Installation InstructionsThis document describes how to install the AT410 Adaptable Transmitter. The AT410 is connected to a smoke detector in a Senior Living facility. It provides a secondary signal which can help isolate the specific location of an emergency when the smoke detector goes off. Figure 1 shows the top and bottom view of AT410 Adaptable Transmitter. Figure 1: Top and Bottom View of AT410 Adaptable TransmitterChanging the Battery in the AT410The AT410 uses a single 9V alkaline battery. You can replace the battery when the unit is installed on the ceiling or when it has been removed. To change the battery: 1. Open the battery compartment door by applying light pressure to the door and pushing it in the direction of the arrow (see Figure 1 for location of battery compartment door).2. Remove the 9V battery from the battery compartment. 3. Disconnect the battery connectors from the battery and properly dispose of the used battery. 4. Connect the battery connectors to a new 9V alkaline battery. 5. Insert the battery into the battery compartment. 6. Slide the battery compartment door back into place.Note: This installation must be performed by a licensed electrician or a certified maintenance technician authorized to access the primary smoke detectors in the facility. Holes used to attach AT410 to ceilingBattery compartment doorHoles for smoke detector wiresScrews used to tighten smoke detector wires Top View Bottom View
4 AT410 Installation InstructionsInstalling the AT410To install the AT410 Adaptable Transmitter:1. Using the wiring diagrams in Figure 2, connect the AT410 to the smoke detector. You must provide the two wires that connect the AT410 to the smoke detector. Figure 2: Wiring Diagrams for AT4102. To secure the wires, loosen the two screws on the bottom of the unit (see Figure 1), then insert the wires into the holes on the front of the unit (see Figure 1), then tighten the screws to hold the wires in place. 3. Attach the AT410 to the ceiling beside the smoke detector by opening the battery compartment and removing the battery (you do not have to disconnect the battery). Insert two screws into the holes in the battery compartment (see Figure 1) and tighten them onto the ceiling. 4. Install the battery into the battery compartment and close the door. AT410
NOTICE TO THE USER Any changes or modifications not expressly approved by Lifeline Systems, Inc. for compliance could void your authority to operate the equipment. FCC AND INDUSTRY CANADA WARNING: This device complies with Part 15 of the FCC rules and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FIELD STRENGTH Less than 5900 mV/m at 3m OPERATING FREQUENCY 312 MHz CHANNELING 1 MODE OF TRANSMISSION Pulse Width Modulation DATA SOURCE Internal only TYPE OF MODULATION OOK OCCUPIED BANDWIDTH 310 MHz - 320 MHz POWER OUTPUT 5 microwatts
In order to determine the range of the communicator and its associated AT410 follow these instructions. Press and hold the Reset bar to enter Test mode. The Reset bar must be pressed and held until the communicator announces, “Start Test.” Continue holding the Reset bar down and then press the test button of the smoke detector until the red LED on the AT410 illuminates ( a transmitting signal is sent when the red LED is illuminating), the Lifeline Communicator will respond “Smoke Learned”. In order to confirm performance after installation is complete, place the Lifeline Communicator in Test Mode (as described above) and test the range by pressing the test button of each smoke detector connected to an AT410 one at a time in all locations within a unit/apartment. When the AT410 signal is received, the communicator will beep confirming proper performance. Your AT410 is designed to be used in and immediately around your home .next to the hard wired smoke detector. The exact area of coverage will vary from one home to another. It is important for you to know the effective range of your AT410. Contact your Lifeline Service Provider for assistance. For installation wiring diagram, see Figure 2 within this manual. The AT410 is a supervised unit when used with Lifeline Communicator Models 6600, 6600S, 6700, or 9500. NOTE If the Response Center receives a Low Battery Button signal, Lifeline recommends that the 9-volt battery be replaced as soon as possible. Lifeline complies with a UL standard that requires the AT410 to operate for seven days after the Low Battery signal is sent. Plan to replace this battery every 2 years. Important Maintenance, Safety and Operating Information *DO NOT USE THE AT410 WITH LIFELINE COMMUNICATOR MODELS: 4500, 4000, 3500, 3000, 2500, 2000 AND HC/VC. AT410 Safety Features: Lifeline recommends using the AT410 with “Supervision COMPATABLE Lifeline Communicators. Features 1 and 2 are only enabled when the AT410 is used with these communicators.
1. The AT410 will periodically test its battery and automatically send a signal to the Response Center if the battery is low. 2. Provides a larger offering of ID codes to accommodate installations in apartments and senior housing. 3. The AT410 provides protection against accidental disconnection. A “Help Needed” signal will automatically be transmitted to the Response Center if the wires are removed from the AT410. Subscriber Testing: Monthly testing is important and recommended by Lifeline. When interacting or corresponding with subscribers, reinforce the need for monthly testing. Test in accordance with the smoke detectors manufacturers recommended procedure. Equipment Repair: Lifeline equipment is factory serviceable and must be repaired by Lifeline Systems, Inc. Any service performed by unauthorized personnel will nullify any warranty. Call Technical Support at 800-451-0525, ext. 1234, should your Lifeline Access™ Equipment need repair. FCC Warning and User Notification Requirement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Lifeline Systems, Inc. for compliance could void your authority to operate the equipment. INDUSTRY CANADA This apparatus complies with the class“B” limits for radio interference as specified in the Canadian Department of Communications Radio Interference regulations. One or more of the following US Patents may apply to this product: D277,465, 4,524,243, 4,656,319, 4,760,593, 4,622,544, 4,908,602, 4,884,059, D313,363, D313,362, 4,064,368, 3,989,900, 5,091,930 One or more of the following Canadian Patents may apply to this product: 1,274,930, 1,256,613
Installing the AT410 5Lifeline Systems Canada Lifeline Systems95 Barber Greene Road, Suite 105 111 Lawrence StreetToronto, Ontario M3C 3E9 Framingham, MA 01702-8156Telephone: 800-387-8120 Telephone: 800-451-0525www.lifelinesys.com www.lifelinesys.comLSI Part # 0940455 Rev. 01June 2004
6 AT410 Installation Instructions

Navigation menu