Lightolier Lytecaster 1000Lv Users Manual Downlights Instruction Sheets

2015-02-09

: Lightolier Lightolier-Lytecaster-1000Lv-Users-Manual-573065 lightolier-lytecaster-1000lv-users-manual-573065 lightolier pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadLightolier Lightolier-Lytecaster-1000Lv-Users-Manual- Lytecaster Downlights Instruction Sheets Lightolier-lytecaster-1000lv-users-manual
Open PDF In BrowserView PDF
INSTRUCTIONSHEETNO.
INSTALLATION

REFLECTOR

PROCEDURE

TRIM

IN THE

lS:1052LV

LOW VOLTAGE
1000LV FRAME-IN
KIT
FOR

Page 1 of 2

0s90

EAD

AND

UNDERSTAND

THESE

INSTRUCTIONS

BEFORE

INSTALLING

FIXTURE.

his fixture is intsndsd for installation
in accordance with the National Electrical Code or Iocsl regulations.
3 assure full compliance
with local codes and regulations, check with your local electrical inepector before
wtallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
ietain these Instruction
for maintenance
referenc~

?~%~

FIG. C
3, eNAP-ON

FIG. B
2. CLOSE4N

1. FRAME-IN

FIG. D
4. PuSH-UP

WARNING:
BEFORE INSTALLING REFLEClOR TIRM TO FRAME4N KIT, READ MARKINGS IN REFLEClOR
TRIM AND fN SOCK~
CUP OF FRAME4N KIT TO DEf’ERMINE LAMP WAITAGE AND TYPE APPLICABLE FOR
YOUR lNSTALLATfON. IF IC. TYPE FRAME.fN KIT IS USED, IT MAY BE INSTALLED fN DIRECT CONTACT WITH
INSULATED CEILING. IF A NON IC. TYPE FRAME4N KIT IS USED, DO No INSTALL lNSULATfON WITHIN
3 INCHSS OF FIXWRE SIDES OR WIRING .COMPARTMENT, NOR ABOVE FfXTURE IN SUCH A MANNER AS ~
ENTRAP HEAT.
1. FRAME-IN (Fig. A)
See Frame-In Kit Instruction
procedwe.

r-.
Sheet for installation
,–
,.,’
... $1..... .. . . . . ..
: ,,..,.
,, ::.:,.;.

!.

R~ATE RUIO-CLIPS
As shown in Fig. E.

L

SNARON (Fig. C).
Disconnect SOCKET from FRAME-IN KIT WIRES
by pulling off the insulated FEMALE
CONNECTORS. Insert FRAME-IN KIT WIRES with
FEMALE CONNECTORS through %“ dia HOLE
on top of REFLECTOR TRIM. Reconnect SOCKET
(provided with REFLECTOR TRIM) by pushing
MALE CONNECTORS into FEMALE CONNECTORS
(Fig. G.)
Engage TAB from SOCKET CUP into one of the
SLOTS on top of REFLECTOR TRIM and push
other end of SOCKET CUP with LANCING into
the other SLOT (Fig. F).

4.

(Fig. B)

PUSH-UP (Fig. D).
Push REFLECTCR TRIM into ceiling
is flush to ceiling (Fig. D).

4

FRAMINGKIT
MOUNTSFLUSH
ON CEILINGMATERIAL

!.;
0“

\

CEILING
MATERIAL

-.: .“.~.-:.
R~-CLIP
“ “:-~~< ;
POSITION
,., ,.
FIG. E

– SOCKETGUp
LANCING
i“ HOLE
SLOTS

. ..
,*

.
,=
,}

*
FIG. F

until flange

REFLECTOR
TRIM

SOCKET
MALECONNECTORS
[Altachedto Sooketwires)

INSULATING
SLEEVING
SEE BACK PAGE FOR LAMPING
AND ADJUSTMENT.

TAe

INSTALLATION

FEMALEGONNECTORS
(Attachedto FixtureWires)
FIG. G

D-9

C31”ITC>I-I

Is

1?

:V:::::;,N:;::::,E:;

:Y::

IS1052LV
0890
Page 2 of 2
5. INSTALL LAMP
NOTE Socket manufacturers have auggeeted that
eocket may fail after 3 to 6 relampings. If this occurs,
socket can be replaced by disconnecting male
connectors (attached to socket leads) from female
connectors (attached to fixture leads) and replacing it
with a new eocket procured through Lightolier (Fig. G).
A, Check to see that power is OFF before Iamping or
relamping.
B. Remove PINHOLE FACE PLATE fmm HOUSING by
inserting fingera in aperture and pull apari from
HOUSING (Fig. H).

PINHOLE
FACE PLATE

~\
G Remove IAMP RING fmm LAMPIYOKE
by pulling straight down (Fig. l).

HOLDER

FIG.

H

LAMPNOKE
HOLDER

D. Insert correct LAMP (MR16) between LAMP
SPRINGS until face of LAMP sits firmly on GLASS
IAMP GUARD (Fig. J). See warninge below.
E. Attach

SOCKET to hi-pin pmnga on LAMP (Fig. J).

E Insert LAMP RING with LAMP and GIASS LAMP
GUARD attached back into LAMP/YOKE HOLDER
(Fig. K or l).
FIG. I

6. VERTfCAL/ANGLE
ADJUSTMENT
Insert a screwdriver into the SLOT in LEG of
lAMPIYOKE
HOLDER, and ueing the screwdriver as
a lever, tilt the entire IAMPIYOKE HOLDER to the
desired angle (Fig. K).
7. HORIZONTAL ADJLKWMENT
A. The entire LAMP/YOKE HOLDER can be
horizontally rotated to aim the angle of light aa it
Ieavea the hole in the APERTURE TRIM (Fig. K).
B. Graspin
the YOKES on either eide of the
LAMP/Y KE HOLDER, rotate the LAMP to the
deeired angle.

8

FIG, J

NOIE
LOW VOLTAGE FIXTURES should be
dimmed only with special dimmers intended
specifically for that purpoea Use Llghtolier
Lytemode, Scenist, Crescendo VA, Neptune VA
Praolslon VA, Easyaet VA, Sunrise VA, Redlent VA
or equivalent produots by others or verleble
autotraneformera
or eleatronlo dlmmera intended
for uae with low voltege fixture% 2. fmw voltage
fixtures may produce audible sound whan ua6d
with dimme~
which may be ob}eotlonsl in
acoustically criticsl erea~

1-
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Modify Date                     : 2001:03:19 16:03:47-05:00
Create Date                     : 2001:03:19 15:58:59-05:00
Title                           : Lytecaster Downlights Instruction Sheets
Subject                         : Lightolier CD-ROM Specifier V3
Author                          : G.Tashian/Lightolier
Creator                         : Acrobat Capture 1.0
Producer                        : Acrobat PDFWriter 2.01 for Windows
Page Count                      : 2
EXIF Metadata provided by EXIF.tools

Navigation menu