Lightspeed Technologies HM016 Wireless Microphone User Manual

Lightspeed Technologies Inc. Wireless Microphone Users Manual

Users Manual

User ManualPortable Public Address SystemDelta PAON
TABLE OF CONTENTSSECTION 1: 4 Safety Instructions5 System Components and UnpackingOverview 6 Optional Components7 Top Panel Wireless Receiver Controls8 Top Panel Controls & Connections9 Rear Panel Controls & Connections10 Installing or Replacing Receiver ModuleSECTION 2: 11 Step 1. Connecting the Delta PA Receiver to a Power SupplySet-up & Use 12 Step 2A. Setting up one DeltaPA Receiver13 Step 2B. Using More Than One Delta PA ReceiverHandheld Transmitter14 Step 3. Channel Selection15 Step 4. Battery Life & Battery Type16 Step 5. Replacing Battery17 Step 6. Recharging BatteriesBelt-pack18 Step 7. Connecting & Placement19 Step 8. Channel Selection20 Step 9. Gain Adjust21 Step 10. Battery Life Indicator & Type22 Step 11. Replacing Batteries23 Step 12. Recharging Batteries24 Daily Use InstructionsSECTION 3: 25 Hand Held Microphone TransmitterOptional Accessories 26 Belt-Pack TransmitterSECTION 4: 27 Troubleshooting GuideTroubleshootingSECTION 5: 28 Warranty StatementWarranty & Specifications29 Safety Warnings 30 System Specifications
41. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsIMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use the apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding- type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.11. Only use attachments/ accessories specified by the manufacturer.12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. Unplug this apparatus during lighting storms or when unused for long periods of time.14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.15. When the mains plug or appliance coupler used as the disconnect device, it shall remain readily operable.16. Please keep the unit in a good ventilation environment.
51. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsSECTION 1: OVERVIEWSYSTEM COMPONENTS AND UNPACKINGThe standard configuration of the Delta PA™ will contain:Delta PA Carry CaseDelta PA Public Address System and Power SupplyHM-016 TransmitterON
61. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsOPTIONAL COMPONENTSOptional equipment which may be part of your Delta PA system:Individual ComponentsRX-016R 100 Channel UHF Receiver ModuleTX-HM016 100 Channel UHF Handheld TransmitterAC-MH7 Mic Clip for HM900 Handheld TransmitterTX-BP016 100 Channel UHF Belt-Pack TransmitterBC-TX900 Battery Charger for BP900 or HM900MC831S Audio-Technica 831 Lapel MicMC-TK270S Lightspeed Noise-cancelling Headset MicPS-15V-4.3 AC Power SupplyBA-NH1 AA NiMH Rechargeable BatteryAC-SPDELTA-PA Carry Bag for Delta PAAC-831CLIP Mic clip for MC-831SAC-PWR-NA AC North American Power CableOptional AccessoriesCA-GTC900 Guitar/aux In Cable for BP900AC-TWBRK Speaker Stand BracketAC-SS1 Tripod Speaker StandAC-SPSS1 Carry Bag for Tripod Speaker StandMC-H10 Wired Dynamic Handheld MicBP-016 Transmitter and ChargerMK-TK270S Noise-Cancelling Headset MicrophoneMC-831S Audio -Technica 831 Lapel Mic
71. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsPOWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1TOP PANEL: WIRELESS RECEIVER CONTROLS5. TRANSMITTER LOW BATTERY INDICATOR: This LED will light to indicate the batteries in the corresponding transmitter are low.6. SCAN: Press this button to auto-matically select a channel that is free from interference.7. SQUELCH LEVEL ADJUSTMENT: Covered with a plastic cap, the squelch is adjusted at the factory to provide the best signal level and minimum noise. There is no need to adjust the squelch level in the field.1. WIRELESS RECEIVER 1: One or two wireless receiver modules are located at the top panel.2. CHANNEL DISPLAY: An LED readout of the receiver module indicates which channel you are on.3. CHANNEL CONTROL (1-16): The left button increments the channel number (1-16). Each touch of the button moves the number up one until it gets to sixteen. The right button decrements the channel number (16-1).4. RF CHANNEL A/B INDICATOR: The “A” LED lights up indicating the A channel tuner is receiving the strongest RF signal. The “B” LED lights up indicating the “B” channel tuner is receiving the strongest RF signal.11236574
81. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsTOP PANEL CONTROLS AND CONNECTIONS1. BASS: Controls the level of low frequency sound output for the system.2. TREBLE: Controls the level of high frequency sound output for the system.NOTE: Reducing FeedbackThe BASS and TREBLE controls can be used to reduce feedback (“squealing” or “howling”). If you hear high-pitched squealing, lower the treble setting. If you hear low-pitched howling, lower the bass setting.3. AUX IN/MIC IN: Controls the volume of a wired microphone plugged into MIC IN on the back of the system and the volume of an auxiliary piece of equipment plugged into the AUX IN on the back of the system.4. WIRELESS RECVR 2: Controls the volume of Wireless Microphone 2 if a second wireless receiver is installed.5. POWER/WIRELESS RECVR 1: Turn this knob clockwise to power up the system. Rotate to adjust the volume of Wireless Microphone 1.6. POWER LED: Green = Power On. Red = Low Battery7. CHARGING LED: Green = Full Charge. Red = Charging123754POWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 16
91. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications12354REAR PANEL CONTROLS AND CONNECTIONSconnected to a recorder, assistive listening device, etc.6. SPEAKER OUT (SWITCHED): This ¼” jack can be used to connect to an external passive speaker. [NOTE: connection to this jack will mute the internal speaker of the Delta PA.]7. FUSE: The fuse holder is accessible using a flat-blade screwdriver. Push in and rotate ¼ turn counterclockwise to remove. [NOTE: replacement is a 4A 250V slow blow fuse.]8. DC POWER: This jack provides a connection for the Delta PA power supply.1. MIC IN: This ¼” jack provides an input for a wired handheld microphone.2. AUX IN: This 3.5 mm jack provides an input for audio from an external device, such as a CD player, MP3 player, TV/VCR, computer, etc. 3. AUX OUT: This 3.5 mm jack provides an adjustable-level audio output that can be connected to a recorder or assistive listening device.4. AUX OUT VOLUME: This knob controls the level of the 3.5 mm AUX OUT jack. Counterclockwise represents a microphone level signal, while fully clockwise represents a line level signal.5. AUX OUT: This ¼” jack provides a line level output signal that can be 678
101. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsINSTALLING OR REPLACING A RECEIVER MODULENOTE: Make sure the Delta PA is turned off.1. Remove the two screws securing the module panel using a small phillips head screwdriver.2. Remove the module from the enclosure by carefully inserting the blade of a small, flat-blade screwdriver under the face plate edge and nudging it upward.3. Grasp the edges of the module with both hands and slide it out.4. Install the new module by aligning it with the guide rails and sliding all the way in to engage the connector at the rear of the module.5. Replace the two screws.POWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1
111. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsSECTION 2: SET-UP & USE1. CONNECTING THE DELTA PA RECEIVER TO A POWER SUPPLY1. Locate the power supply. 2. Insert the DC connector into the “POWER INPUT” connector on the bottom of the Delta PA and plug the other end to an electrical outlet.3. Turn the RCVR 1/WIRELESS knob clockwise to turn the system on. 4. The GREEN LED light next to the knob will illuminate to confirm the system is powered up.POWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1POWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1
121. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications2A. SETTING UP ONE DELTA PA RECEIVER1. Turn the Delta PA ON by rotating the RCVR 1 knob clockwise. The GREEN LED will light.Channel Selection: Receiver Each Receiver has 16 user-selectable channels to choose from. You can either select a channel manually or by pressing the SCAN button, which will automatically select a clear channel. 2. Clear Channel SCAN (recommended): A) Make sure the transmitter(s) is OFF before pressing this button. When this button is pressed, the receiver will cycle through all 16 channels and select a clear frequency. (This process takes about 20 seconds.) B) Once the receiver selects the clear channel, you will need to select the same channel on the corresponding transmitter (handheld or belt-pack). See pages 11 and 16 for instructions.NOTE There are 3 different groupings of 16 channels available (620, 645, 670 MHz). Make sure the receiver module frequency group is the same frequency group as the transmitter.ONChannel 2POWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1POWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1
131. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications2B. USING MORE THAN ONE DELTA PA RECEIVERIf you have a second Delta PA: A) Verify that RECVR 1 transmitter and receiver are ON and set to the same clear channel. B) Make sure the transmitter for RECVR 2 is turned OFF. C) Press the SCAN button on the RECVR 2 receiver. D) After the RECVR 2 receiver selects a clear channel, set the RECVR 2 transmitter (handheld or belt-pack) to the selected channel. See pages 11 and 16 for instructions.3. Manual Channel Selection: A) Pressing the UP CHANNEL button increases the channel number by one. B) Pressing the DOWN CHANNEL button decreases the channel number by one. C) Once a frequency is selected, you will need to select the same channel on the corresponding transmitter (handheld or belt-pack). See pages 11 and 16 for instructions.4. Set the Receiver 1 and Receiver 2 channels to be the same as the first Delta PA.ONChannel 2
141. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications3. CHANNEL SELECTION: HANDHELD TRANSMITTEROnce a channel has been selected on the receiver, you now need to select that same channel on the handheld transmitter. If you have a belt-pack transmitter, go to page 18 for channel selection instructions.1. Turn on the microphone by sliding the power button on the barrel forward.2. Use a screwdriver to set the channel switch to the current channel shown on the RECVR screen.Transmitters and receivers are available in 3 different frequency groups (620, 645, 670 MHz). Verify that the receiver frequency matches the letter code on the silver sticker in the battery compartment of the transmitter. Model Number: HM016Serial NumberHM01614324024FREQUENCY 670 MADE IN TAIWANONSame ChannelONFrequency
151. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsON4. BATTERY LIFE INDICATOR AND BATTERY-TYPE ON HANDHELD MICROPHONEBattery Life IndicatorThe battery low indicator lights red when the battery charge is low.Battery TypeThe transmitter will operate with either standard AA alkaline batteries or nickel metal hydride (NiMH) rechargeable batteries. Since these types of batteries have different characteristics, it is important not to mix battery types. Use only AA NiMH batteries when recharging.NOTE: Do not mix battery types. WARNING: Do not use NiCad batteries! They will not charge properly and may cause damage to the transmitter.Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work.Low Battery Light
161. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsON5. REPLACING BATTERIES IN HANDHELD MICROPHONEReplacing the Batteries 1. Unscrew the end cap to reveal the battery compartment.2. Remove or replace the batteries as shown. The microphone requires two AA sized batteries stacked end to end.3. Note the polarity in the battery compartment.IMPORTANT: Replace batteries with the same type, (alkaline or NiMH), that were installed in your Handheld Microphone. Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work properly.
171. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications6. RECHARGING BATTERIES IN HANDHELD MICROPHONERecharging the Batteries (NiMH Rechargeable Batteries ONLY): Make sure there are NiMH rechargeable batteries in the transmitter before plugging in the charger. A full charge will be attained in 8-10 hours. Fully charged Lightspeed microphones will last over 7 hours.WARNING: Do not attempt to charge alkaline batteries. They can overheat and expand, creating a significant hazard and damaging the transmitter. (This is not covered by warranty.)1. Switch the transmitter power OFF.2. Insert the small DC plug into the jack on the bottom of the transmitter.3. Plug the other end of the charger into any standard 110 VAC outlet.4. The RED LED on the charger will light, indicating that charging is in progress.5. When the batteries are fully charged, the LED on the charger will glow GREEN.ON
181. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications7. CONNECTING AND PLACING BELT-PACK TRANSMITTERConnecting the MicrophoneTo connect the microphone, simply insert the microphone connector into the TA4F connector on top of the transmitter. To remove, press the black button on the microphone connector and pull out.Microphone OptionsLightspeed offers various types of microphones that can be used with this system. The BP-016 Transmitter can be used with either a lapel style microphone or a headset microphone. Both plug into the top of the transmitter as shown.Lapel Microphone PlacementSeveral varieties of lapel microphones are available. Simply connect the microphone cord directly into the jack on top of the transmitter and clip the microphone to lapel or collar. For optimal sound, position the microphone as close to the mouth as possible.Headset Microphone PlacementSeveral varieties of headset microphones are available. Simply connect the microphone cord directly into the jack on top of the transmitter and place the headset around the back of the head. For optimal sound, position the microphone at the corner of the mouth.
191. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications8. CHANNEL SELECTION: BELT-PACK TRANSMITTERChannel Selection:Once a channel has been selected on the receiver, you now need to select that same channel on the Belt-pack transmitter.1. Turn the transmitter power ON by sliding the PWR button to ON.2. Open the battery compartment door by depressing the latches on each side of the transmitter.3. Use the screwdriver channel set to switch to the current channel shown on the receiver. Transmitters and receivers are available in 3 different frequency groups (620, 645, 670 MHz). Verify that the frequency group of the receiver matches the letter code on the silver sticker in the battery compartment of the transmitter. Model Number: BP016Serial NumberBP01614324024FREQUENCY 670 MADE IN TAIWAN
201. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications9. GAIN ADJUST ON BELT-PACK TRANSMITTERNOTE: If you are using a high impedance source, such as a guitar, it will be necessary to adjust the GT dial. Using a high impedance source requires a special cable. Contact Lightspeed Customer Service at 800-732-8999 for more information.Gain Adjust:When changing microphones or users, it may be necessary to adjust the transmitter gain based on differing microphones sensitivities and voice levels.To adjust the gain:1. Open the battery compartment door by depressing the latches on each side of the transmitter.2. Turn the MT dial clockwise to increase the gain and counterclockwise to decrease the gain.
211. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications10. BATTERY LIFE INDICATOR AND TYPE ON BELT-PACK TRANSMITTERBattery Life IndicatorBattery low indicator is located next to the power switch. It glos red when the battery charge is low and recharging is necessary.Battery TypeThe transmitter will operate with either standard AA alkaline batteries or nickel metal hydride (NiMH) rechargeable batteries. Since these types of batteries have different characteristics, it is important not to mix battery types. use only AA NiMH batteries when recharging.NOTE: Do not mix battery types. WARNING: Do not use NiCad batteries! They will not charge properly and may cause damage to the transmitter.Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work.
221. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications11. REPLACING BATTERIES IN BELT-PACK TRANSMITTERReplacing the Batteries: 1. Open the battery compartment door by depressing the latches on each side of the transmitter.2. Remove or replace the batteries and snap the door shut. The belt-pack requires two AA sized batteries.3. Note the polarity in the battery compartment.IMPORTANT: Replace batteries with the same type, (alkaline or NiMH), that were installed in your Handheld Microphone. Lightspeed recommends Panasonic or Energizer batteries. Duracell may not work properly.
231. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications12. RECHARGING BATTERIES IN BELT-PACK TRANSMITTERRecharging the Batteries (NiMH Rechargeable Batteries ONLY): Make sure there are NiMH recharge-able batteries in the transmitter before plugging in the charger. Typical battery life is about 8 hours. Fully charged Lightspeed transmitters will last over 7 hours. A full charge will be attained in 8-10 hours.WARNING: Do not attempt to charge alkaline batteries. They can overheat and expand, creating a significant hazard and damaging the transmitter. (This is not covered by warranty.)1. Switch the transmitter power OFF.2. Insert the small DC plug into the jack on the side of the transmitter.3. Plug the other end of the charger into any standard 110 VAC outlet.4. The RED LED on the charger will light, indicating that charging is in progress.5. When the batteries are fully charged, the LED on the charger will glow GREEN.
241. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsPOWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1POWERCHARGERED: LOW BATT GREEN: ONRED: CHARGING GREEN: FULLRECVR 1RECVR 2RECVR 2O/IPOWER/RECVR 1DAILY USE INSTRUCTIONS1. Wireless Microphone Operation RF Indicator Lights: When both the system and the transmitter are ON and operating on the same channel you will see a BLUE glowing RF Indicator Light (either A or B) on the receiver.2. VOLUME ADJUSTMENT: While speaking into the microphone, slowly turn the RECVR1 volume knob (or RECVR2, depending on which microphone you are operating) clockwise until you reach the desired level.NOTE: Do not stand directly in front of the Delta PA speaker with the microphone on. This will result in feedback or ‘squealing.’ It is best to stand behind or to the side of the unit when setting volume level.3. SQUELCH ADJUSTMENT: Adjusting the squelch level may be necessary to block out potential interference in areas that have that have very high radio traffic.• Maximumsquelch(fullclockwise)reduces reception range but also reduces the potential for system interference.• Minimumsquelch(fullcounter-clockwise) increases reception range, but also increases the potential for system interference.NOTE: In most cases it will not be necessary to adjust the squelch level. The system already has a clear channel scanner to take care of most interference problems.4. TRANSMITTER LOW BATTERY INDICATOR: This LED will light to indicate the batteries in the corresponding transmitter are low and need to be replaced or recharged.
252. Setup & Use 3. Optional Accessories1. Overview 4. Troubleshooting 5. Warranty, Safety & SpecificationsONSECTION 3: OPTIONAL ACCESSORIESHANDHELD MICROPHONE TRANSMITTER1. RED LED: Lights up briefly when power is switched on, flashes continuously when audio is muted.2. POWER ON/OFF: Turns the audio ON and OFF. The RED LED will flash when power is turned ON.3. CHANNEL SWITCH: A screwdriver adjust to set channel 1-16 to match the channel setting of its receiver.4. BATTERY COMPARTMENT: Bottom section of microphone barrel unscrews to reveal battery compartment. 1234
261. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsBELT-PACK TRANSMITTER7. GT (TRANSMITTER GAIN): Provides adjustment for differing voice levels and microphone sensitivities.8. MT (MICROPHONE GAIN): Provides adjustment for differing voice levels and microphone sensitivities.9. CHANNEL SET SWITCH: Screwdriver adjust to set the channel 1-16 to match its receiver channel.10. BATTERY COMPARTMENT1. ON/OFF BUTTON2. RED LED: Lights up briefly when power is switched ON, flashes continuously when audio signal is muted.3. MICROPHONE JACK: Microphone connects to transmitter here.4. ANTENNA5. BATTERY CHARGER JACK: Optional battery charger plugs in here (for NiMH batteries only.)6. DOOR LATCHES: Press both latches to open the battery compartment door.1362 461079 85
271. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsIf you review these instructions and still have questions, write down the serial number and model number of your system and call Lightspeed Technical Services at 800.732.8999, 5 a.m. – 5 p.m., PST.No sound when someone speaks into the wireless microphone:1. Delta PA power should be ON. The GREEN LED should be lit. If it does not light when the system is switched on, make sure the AC power supply is plugged in.2. Microphone/transmitter power should be ON. If the low battery indicator is on (red) the batteries are most likely too weak. If the batteries are rechargeable, plug the microphone/transmitter into the charger. If the batteries are alkaline, replace them with new alkaline batteriesWARNING: Do not attempt to charge alkaline batteries. They can overheat and expand, creating a significant hazard and damaging the warranty. (This is not covered by warranty.).3. The transmitter and receiver should be set to the same channel. The BLUE RF LED (A or B) should be lit.4. Make sure the MUTE light is not flashing. Switch the transmitter/microphone off of MUTE.5. Verify that receiver and transmitter are in the same frequency group. Turn the Delta PA OFF and then ON again. The letter code from the frequency group will blink on the receiver module. Open the battery compartment on the transmitter and be sure that frequency group printed on the sticker matches the frequency group letter code that blinked when the Delta PA powered ON. If the letters are different, find a microphone or belt-pack with the same frequency group as the receiver indicates when the Delta PA is turned ON.The wireless mic is experiencing drop-out or interference: 1. The wireless frequency being used may not be a clear channel. Turn the transmitter OFF and press the SCAN button on the receiver to find a clear frequency. Then select the same channel on the transmitter.2. Transmitter is out of range of receiver. The transmitters have a maximum range of about 300-350 feet in an open field environment. This range can be dramatically reduced indoors and outdoors when large objects (such as a wall) may be obstructing the path directly between transmitter and receiver. If so, position the two closer together.3. Batteries are very weak. Right before the batteries are about to die, the overall performance of the system can be drastically lessened. Check the battery status of the transmitter.Low Volume or Feedback:1. Ensure microphone is positioned appropriately. 2. Check volume level on the amplifier. If the volume is too high, feedback will occur. Adjust accordingly.Note: Most problems are directly related to low battery power. Please run through the “Battery Check” items first. For remaining troubleshooting, use known good, fully-charged batteries.SECTION 4: TROUBLESHOOTINGCOMMON PROBLEMS AND SOLUTIONS
281. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications5. Warranty is void when equipment is subjected to adverse temperature, humidity, moisture, or other conditions that are not considered normal environmental conditions.6. This warranty excludes all damages or defects caused by shipping, transporting, or inadequate packaging for shipping.7. Customers are responsible for freight charges to Lightspeed Technologies for service. Lightspeed Technologies will pay for return freight to the end user by most reasonable method.The warranty period for each system and component type is listed below:Delta PA: Six (6) years from the date of original purchase.RF Wireless Transmitters and Receivers: Three (3) years from the date of purchase.Batteries: One (1) year from the date of purchase.Microphones and Cases: One (1) year from date of purchase.Products will be replaced or repaired at Lightspeed Technologies’ option during the warranty period.Lightspeed Classroom Audio Systems are guaranteed against malfunction due to defects in materials and workmanship for a period of THREE (3) YEARS, beginning at the date of the purchase invoice. If such malfunction occurs, the product will be repaired or replaced (at Lightspeed’s option) without charge during the warranty period, subject to the following conditions:1. The product must have been purchased from an authorized Lightspeed Technologies Dealer or representative. 2. Lightspeed Technologies must perform all warranty service. Any service performed without the authorization of Lightspeed Technologies will void the entire warranty.3. This warranty does not cover any product that has been subjected to negligent use, connection to improper power source, misuse, or operated beyond its manufactured specifications and limits, or has not been reasonably maintained.4. Warranty shall not apply to alkaline or NiMH batteries, exterior finish, AC power cords, bulbs, or any other failings due to normal wear.THREE-YEAR LIMITED WARRANTYFor warranty service, please contact Lightspeed Customer Service Department to obtain return authorization approval and an RA number.Our Service Department (800.732.8999, 5 a.m. – 5 p.m., PST) will handle all your repair/replacement needs.SECTION 5: WARRANTY, SAFETY & SPECIFICATIONS
291. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsSAFETY WARNINGSThe lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be sufficient magnitude to constitute a risk of electric shock.The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.This product is listed to UL standards and requirements for electrical safety by Underwriters Laboratories Inc. LIGHTSPEED TECHNOLOGIES, INC. PH: 1.800.732.8999FCC CautionThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).DELTA PA & BP016 & HM016 ：IC ID CautIonthIs DevICe ComplIes wIth InDustry CanaDa lICenCe-exempt rss-123 stanDarD.operatIon Is subjeCt to the followIng two ConDItIons: (1) thIs DevICe may not Cause InterferenCe, anD (2) thIs DevICe must aCCept any InterferenCe, InCluDIng InterferenCe that may Cause unDesIreD operatIon of the DevICe. BP016 & HM016 ：fCC CautIonthIs DevICe ComplIes wIth part 74 of the fCC rules.thIs equIpment ComplIes wIth fCC rf raDIatIon exposure lImIts set forth for an unControlleD envIronment.
301. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsOVERALL SPECIFICATIONSNominal SPL [1W/1M] 89 dBMaximum SPL 102 dBSystem Power [RMS] 30 W at 2 ΩMusic Power [RMS] 40 W at 2 ΩAmplifier Type Analog Class ABFrequency Response of amplifier 90 Hz - 18 kHzSpeaker System Full-Range 6.5”/4 ΩMicrophone Input ¼ inch phone jackWireless Microphones Up to two 100-Channel UHF True DiversityLine Input 3.5 mmLine Output 3.5mm and ¼ inchTone Controls Bass and TrebleSpeaker Output 1 switched 2 ΩDimensions [H x W x D inches] 9.75 x 12.5 x 6.25Weight 7.2 lbs./20.4 kgSYSTEM SPECIFICATIONS
311. Overview 2. Setup & Use 3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & SpecificationsRECEIVER SPECIFICATIONSCarrier System Microprocessor Controlled PLL SynthesizedMacro Frequency Range 620 ti 694.75 MHz [3 Macro-Groups]Micro Frequency Range 25 MHz each Macro-GroupSelectable Frequencies 100Deviation ± 40 KHz Nominal Sensitivity -100 dBm at S/N ratio of >80 dBTone-code Frequency 32.768 KHzImage Rejection >85 dBS/N Ration [Max] >105 dBTRANSMITTER SPECIFICATIONSHM-016 Handheld MicrophoneRF Power Output 50 mW MaximumSpurious Emission >60 dB below the carrierMacro Frequency Range 620 MHz to 694.75 MHz [3 Macro-Groups]Selectable Frequencies 16Tone-Code Frequency 32.768 KHzPre-Emphasis 50 µsecLimiter Range >30 dB or audio overloadBattery Type 2 AABattery Life [Alkaline] Approx. 8 HoursWeight w/o Batteries 4.2 oz/120 gBP-016 Belt-packRF Power Output 50 mW MaximumSpurious Emission >60 dB below the carrierMacro Frequency Range 620 MHz to 694.75 MHz [3 Macro-Groups]Selectable Frequencies 16Tone-Code Frequency 32.768 KHzPre-Emphasis 50 µsecLimiter Range >30 dB or audio overloadBattery Type 2 AABattery Life [Alkaline] Approx. 8 HoursMicrophone Connector TA4FWeight w/o Batteries 3 oz/85 gSYSTEM SPECIFICATIONS CONT’DCHANNEL FREQUENCY ASSIGNMENTEE 620.000 - 639.750HH 640.000 - 659.750LL 660.000 - 679.750
LIGHTSPEED TECHNOLOGIES 11509 SW HERMAN ROAD / TUALATIN, OR 97062TOLL FREE: 800.732.8999 / PHONE: 503.684.5538 / FAX: 503.684.3197LIGHTSPEED-TEK.COMMN0374US01-0

Navigation menu