Lightspeed Technologies HM016 Wireless Microphone User Manual

Lightspeed Technologies Inc. Wireless Microphone Users Manual

Users Manual

Download: Lightspeed Technologies HM016 Wireless Microphone User Manual
Mirror Download [FCC.gov]Lightspeed Technologies HM016 Wireless Microphone User Manual
Document ID1567663
Application IDKSY6yVy/Zw8I7XN0IZHlpA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize395.89kB (4948677 bits)
Date Submitted2011-10-26 00:00:00
Date Available2011-10-26 00:00:00
Creation Date2011-05-04 15:22:12
Producing SoftwareAdobe PDF Library 9.9
Document Lastmod2011-05-09 20:46:40
Document TitleUsers Manual
Document CreatorAdobe InDesign CS5 (7.0.4)

Delta PA
ON
Portable Public Address System
User Manual
TABLE OF CONTENTS
SECTION 1:
Safety Instructions
10
System Components and Unpacking
Optional Components
Top Panel Wireless Receiver Controls
Top Panel Controls & Connections
Rear Panel Controls & Connections
Installing or Replacing Receiver Module
SECTION 2:
11
Set-up & Use
12
13
18
19
20
21
22
23
24
Step 1. Connecting the Delta PA Receiver to
a Power Supply
Step 2A. Setting up one DeltaPA Receiver
Step 2B. Using More Than One Delta PA
Receiver
Handheld Transmitter
Step 3. Channel Selection
Step 4. Battery Life & Battery Type
Step 5. Replacing Battery
Step 6. Recharging Batteries
Belt-pack
Step 7. Connecting & Placement
Step 8. Channel Selection
Step 9. Gain Adjust
Step 10. Battery Life Indicator & Type
Step 11. Replacing Batteries
Step 12. Recharging Batteries
Daily Use Instructions
SECTION 3:
Optional Accessories
25
26
Hand Held Microphone Transmitter
Belt-Pack Transmitter
SECTION 4:
Troubleshooting
27
Troubleshooting Guide
SECTION 5:
Warranty &
Specifications
28
29
30
Warranty Statement
Safety Warnings
System Specifications
Overview
14
15
16
17
5. Warranty, Safety
& Specifications
4. Troubleshooting
3. Optional
Accessories
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use the apparatus near
water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation
openings. Install in accordance
with the manufacturer’s
instructions.
8.
1. Overview
2. Setup & Use
9.
Do not install near any heat
sources such as radiators,
heat registers, stoves, or
other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety
purpose of the polarized
or grounding-type plug.
A polarized plug has two
blades with one wider than
the other. A grounding- type
plug has two blades and a
third grounding prong. The
wide blade or the third prong
is provided for your safety. If
the provided plug does not
fit into your outlet, consult an
electrician for replacement of
the obsolete outlet.
10. Protect the power cord
from being walked on or
pinched particularly at plugs,
convenience receptacles, and
the point where they exit from
the apparatus.
11. Only use attachments/
accessories specified by the
manufacturer.
12. Use only with a cart, stand,
tripod, bracket or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during
lighting storms or when
unused for long periods of
time.
14. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus
has been damaged in any way,
such as power-supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus, the
apparatus has been exposed
to rain or moisture, does not
operate normally, or has been
dropped.
15. When the mains plug or
appliance coupler used as
the disconnect device, it shall
remain readily operable.
16. Please keep the unit in a good
ventilation environment.
OVERVIEW
SYSTEM COMPONENTS AND UNPACKING
The standard configuration of the Delta PA™ will contain:
1. Overview
2. Setup & Use
3. Optional
Accessories
Delta PA Public
Address System
and Power Supply
4. Troubleshooting
5. Warranty, Safety
& Specifications
SECTION 1:
ON
HM-016 Transmitter
Delta PA Carry Case
5. Warranty, Safety
& Specifications
OPTIONAL COMPONENTS
Optional equipment which may be part of your Delta PA system:
1. Overview
2. Setup & Use
3. Optional
Accessories
4. Troubleshooting
BP-016 Transmitter and
Charger
MK-TK270S NoiseCancelling Headset
Microphone
MC-831S Audio
-Technica 831 Lapel
Mic
Individual Components
RX-016R
TX-HM016
AC-MH7
TX-BP016
BC-TX900
MC831S
MC-TK270S
PS-15V-4.3
BA-NH1
AC-SPDELTA-PA
AC-831CLIP
AC-PWR-NA
100 Channel UHF Receiver Module
100 Channel UHF Handheld Transmitter
Mic Clip for HM900 Handheld Transmitter
100 Channel UHF Belt-Pack Transmitter
Battery Charger for BP900 or HM900
Audio-Technica 831 Lapel Mic
Lightspeed Noise-cancelling Headset Mic
AC Power Supply
AA NiMH Rechargeable Battery
Carry Bag for Delta PA
Mic clip for MC-831S
AC North American Power Cable
Optional Accessories
CA-GTC900
AC-TWBRK
AC-SS1
AC-SPSS1
MC-H10
Guitar/aux In Cable for BP900
Speaker Stand Bracket
Tripod Speaker Stand
Carry Bag for Tripod Speaker Stand
Wired Dynamic Handheld Mic
4. Troubleshooting
RECVR 2
GREEN: FULL
3. Optional
Accessories
GREEN: ON
CHARGE
RECVR 1
1. WIRELESS RECEIVER 1: One or
two wireless receiver modules are
located at the top panel.
2. CHANNEL DISPLAY: An LED
readout of the receiver module
indicates which channel you are on.
3. CHANNEL CONTROL (1-16): The
left button increments the channel
number (1-16). Each touch of the
button moves the number up one
until it gets to sixteen. The right
button decrements the channel
number (16-1).
4. RF CHANNEL A/B INDICATOR:
The “A” LED lights up indicating
the A channel tuner is receiving
the strongest RF signal. The “B”
LED lights up indicating the “B”
channel tuner is receiving the
strongest RF signal.
5. TRANSMITTER LOW BATTERY
INDICATOR: This LED will light
to indicate the batteries in the
corresponding transmitter are low.
2. Setup & Use
O/I
POWER/
RECVR 1
POWER
RED: LOW BATT
RED: CHARGING
1. Overview
RECVR 2
5. Warranty, Safety
& Specifications
TOP PANEL: WIRELESS RECEIVER CONTROLS
6. SCAN: Press this button to automatically select a channel that is
free from interference.
7. SQUELCH LEVEL ADJUSTMENT:
Covered with a plastic cap, the
squelch is adjusted at the factory
to provide the best signal level
and minimum noise. There is no
need to adjust the squelch level in
the field.
1
4. Troubleshooting
5. Warranty, Safety
& Specifications
TOP PANEL CONTROLS AND
CONNECTIONS
RECVR 2
3. Optional
Accessories
RECVR 2
O/I
POWER/
RECVR 1
POWER
RED: LOW BATT
GREEN: ON
CHARGE
2. Setup & Use
RED: CHARGING
GREEN: FULL
RECVR 1
1. Overview
1. BASS: Controls the level of low
frequency sound output for the
system.
2. TREBLE: Controls the level of high
frequency sound output for the
system.
NOTE: Reducing Feedback
The BASS and TREBLE controls
can be used to reduce feedback
(“squealing” or “howling”). If you
hear high-pitched squealing, lower
the treble setting. If you hear lowpitched howling, lower the bass
setting.
3. AUX IN/MIC IN: Controls the
volume of a wired microphone
plugged into MIC IN on the back
of the system and the volume of
an auxiliary piece of equipment
plugged into the AUX IN on the
back of the system.
4. WIRELESS RECVR 2: Controls the
volume of Wireless Microphone
2 if a second wireless receiver is
installed.
5. POWER/WIRELESS RECVR 1:
Turn this knob clockwise to power
up the system. Rotate to adjust the
volume of Wireless Microphone 1.
6. POWER LED: Green = Power On.
Red = Low Battery
7. CHARGING LED: Green = Full
Charge. Red = Charging
4. Troubleshooting
5. Warranty, Safety
& Specifications
REAR PANEL CONTROLS AND CONNECTIONS
3. Optional
Accessories
1. MIC IN: This ¼” jack provides
an input for a wired handheld
microphone.
2. AUX IN: This 3.5 mm jack provides
an input for audio from an external
device, such as a CD player, MP3
player, TV/VCR, computer, etc.
3. AUX OUT: This 3.5 mm jack
provides an adjustable-level audio
output that can be connected to
a recorder or assistive listening
device.
4. AUX OUT VOLUME: This knob
controls the level of the 3.5 mm
AUX OUT jack. Counterclockwise
represents a microphone level
signal, while fully clockwise
represents a line level signal.
connected to a recorder, assistive
listening device, etc.
6. SPEAKER OUT (SWITCHED): This
¼” jack can be used to connect
to an external passive speaker.
[NOTE: connection to this jack will
mute the internal speaker of the
Delta PA.]
1. Overview
2. Setup & Use
7. FUSE: The fuse holder is
accessible using a flat-blade
screwdriver. Push in and rotate ¼
turn counterclockwise to remove.
[NOTE: replacement is a 4A 250V
slow blow fuse.]
8. DC POWER: This jack provides a
connection for the Delta PA power
supply.
5. AUX OUT: This ¼” jack provides a
line level output signal that can be
5. Warranty, Safety
& Specifications
4. Troubleshooting
3. Optional
Accessories
NOTE: Make sure the Delta PA is
turned off.
1. Remove the two screws securing
the module panel using a small
phillips head screwdriver.
2. Remove the module from the
enclosure by carefully inserting
the blade of a small, flat-blade
screwdriver under the face plate
edge and nudging it upward.
3. Grasp the edges of the module
with both hands and slide
it out.
4. Install the new module by aligning
it with the guide rails and sliding
all the way in to engage the
connector at the rear of the
module.
5. Replace the two screws.
1. Overview
2. Setup & Use
INSTALLING OR REPLACING A RECEIVER
MODULE
RECVR 2
RECVR 2
O/I
POWER/
RECVR 1
10
POWER
RED: LOW BATT
GREEN: ON
SET-UP & USE
1. CONNECTING THE DELTA PA RECEIVER
TO A POWER SUPPLY
1. Locate the power supply.
2. Setup & Use
3. Optional
Accessories
2. Insert the DC connector into the
“POWER INPUT” connector on the
bottom of the Delta PA and plug
the other end to an electrical
outlet.
4. Troubleshooting
5. Warranty, Safety
& Specifications
SECTION 2:
1. Overview
RECVR 2
3. Turn the RCVR 1/WIRELESS knob
clockwise to turn the system
on.
4. The GREEN LED light next to the
knob will illuminate to confirm the
system is powered up.
RECVR 2
RECVR 2
RECVR 2
O/I
POWER/
RECVR 1
POWER
RED: LOW BATT
GREEN: ON
CHARGE
RED: CHARGING
O/I
POWER/
RECVR 1
POWER
RED: LOW BATT
GREEN: ON
CHARGE
GREEN: FULL
RED: CHARGING
GREEN: FULL
RECVR 1
11
2A. SETTING UP ONE DELTA PA RECEIVER
RECVR 2
RECVR 2
1. Turn the Delta PA ON by rotating
the RCVR 1 knob clockwise. The
GREEN LED will light.
O/I
POWER/
RECVR 1
POWER
RECVR 2
RED: LOW BATT
O/I
POWER/
RECVR 1
GREEN: ON
CHARGE
GREEN: FULL
RED: CHARGING
1. Overview
GREEN: FULL
RECVR 1
Channel Selection: Receiver
Each Receiver has 16 user-selectable
channels to choose from. You can
either select a channel manually or by
pressing the SCAN button, which will
automatically select a clear channel.
RECVR 1
2. Clear Channel SCAN
(recommended):
A) Make sure the transmitter(s) is
OFF before pressing this button.
When this button is pressed, the
receiver will cycle through all
16 channels and select a clear
frequency. (This process takes
about 20 seconds.)
B) Once the receiver selects the
clear channel, you will need to
select the same channel on the
corresponding transmitter
(handheld or belt-pack). See pages
11 and 16 for instructions.
ON
Channel 2
NOTE There are 3 different groupings
of 16 channels available (620, 645,
670 MHz). Make sure the receiver
module frequency group is the same
frequency group as the transmitter.
12
GREEN: ON
CHARGE
POWER
RED: LOW BATT
RED: CHARGING
2. Setup & Use
3. Optional
Accessories
4. Troubleshooting
5. Warranty, Safety
& Specifications
RECVR 2
5. Warranty, Safety
& Specifications
2B. USING MORE THAN ONE DELTA PA
RECEIVER
If you have a second Delta PA:
4. Troubleshooting
A) Verify that RECVR 1
transmitter and receiver are ON
and set to the same clear channel.
B) Make sure the transmitter for
RECVR 2 is turned OFF.
C) Press the SCAN button on the
RECVR 2 receiver.
3. Optional
Accessories
D) After the RECVR 2 receiver
selects a clear channel, set 		
the RECVR 2 transmitter (handheld
or belt-pack) to the selected
channel. See pages 11 and 16 for
instructions.
2. Setup & Use
3. Manual Channel Selection:
A) Pressing the UP CHANNEL
button increases the channel
number by one.
B) Pressing the DOWN CHANNEL
button decreases the channel
number by one.
1. Overview
C) Once a frequency is selected,
you will need to select the same
channel on the corresponding
transmitter (handheld or beltpack). See pages 11 and 16 for
instructions.
ON
4. Set the Receiver 1 and Receiver
2 channels to be the same as the
first Delta PA.
Channel 2
13
5. Warranty, Safety
& Specifications
4. Troubleshooting
3. CHANNEL SELECTION: HANDHELD
TRANSMITTER
Once a channel has been selected on
the receiver, you now need to select
that same channel on the handheld
transmitter. If you have a belt-pack
transmitter, go to page 18 for channel
selection instructions.
ON
1. Turn on the microphone by sliding
the power button on the barrel
forward.
2. Use a screwdriver to set the
channel switch to the current
channel shown on the RECVR
screen.
1. Overview
ON
2. Setup & Use
3. Optional
Accessories
Same
Channel
Transmitters and receivers are
available in 3 different frequency
groups (620, 645, 670 MHz). Verify
that the receiver frequency matches
the letter code on the silver sticker
in the battery compartment of the
transmitter.
Model Number: HM016
Serial Number
HM01614324024
FREQUENCY 670 MADE IN TAIWAN
Frequency
14
5. Warranty, Safety
& Specifications
4. BATTERY LIFE INDICATOR AND BATTERYTYPE ON HANDHELD MICROPHONE
4. Troubleshooting
Battery Life Indicator
The battery low indicator lights red
when the battery charge is low.
3. Optional
Accessories
ON
Low Battery Light
1. Overview
The transmitter will operate with
either standard AA alkaline batteries
or nickel metal hydride (NiMH)
rechargeable batteries. Since these
types of batteries have different
characteristics, it is important not to
mix battery types. Use only AA NiMH
batteries when recharging.
2. Setup & Use
Battery Type
NOTE: Do not mix battery types.
WARNING: Do not use NiCad
batteries! They will not charge
properly and may cause damage to
the transmitter.
Lightspeed recommends Panasonic
or Energizer batteries. Duracell may
not work.
15
5. Warranty, Safety
& Specifications
5. REPLACING BATTERIES IN HANDHELD
MICROPHONE
1. Overview
2. Setup & Use
3. Optional
Accessories
16
1. Unscrew the end cap to reveal the
battery compartment.
2. Remove or replace the batteries as
shown. The microphone requires
two AA sized batteries stacked
end to end.
3. Note the polarity in the battery
compartment.
IMPORTANT: Replace batteries
with the same type, (alkaline or
NiMH), that were installed in your
Handheld Microphone. Lightspeed
recommends Panasonic or Energizer
batteries. Duracell may not work
properly.
ON
4. Troubleshooting
Replacing the Batteries
4. Troubleshooting
Recharging the Batteries
(NiMH Rechargeable Batteries ONLY):
ON
2. Insert the small DC plug into the
jack on the bottom of
the transmitter.
3. Plug the other end of the charger
into any standard 110 VAC outlet.
4. The RED LED on the charger will
light, indicating that charging is in
progress.
1. Overview
WARNING: Do not attempt to
charge alkaline batteries. They can
overheat and expand, creating a
significant hazard and damaging the
transmitter. (This is not covered by
warranty.)
2. Setup & Use
3. Optional
Accessories
Make sure there are NiMH
rechargeable batteries in the
transmitter before plugging in
the charger. A full charge will be
attained in 8-10 hours. Fully charged
Lightspeed microphones will last over
7 hours.
1. Switch the transmitter power OFF.
5. Warranty, Safety
& Specifications
6. RECHARGING BATTERIES IN HANDHELD
MICROPHONE
5. When the batteries are fully
charged, the LED on the charger
will glow GREEN.
17
5. Warranty, Safety
& Specifications
7. CONNECTING AND PLACING BELT-PACK
TRANSMITTER
1. Overview
2. Setup & Use
3. Optional
Accessories
4. Troubleshooting
Connecting the Microphone
To connect the microphone, simply
insert the microphone connector
into the TA4F connector on top of
the transmitter. To remove, press
the black button on the microphone
connector and pull out.
Microphone Options
Lightspeed offers various types of
microphones that can be used with
this system. The BP-016 Transmitter
can be used with either a lapel
style microphone or a headset
microphone. Both plug into the top
of the transmitter as shown.
Lapel Microphone Placement
Several varieties of lapel microphones
are available. Simply connect the
microphone cord directly into the
jack on top of the transmitter and
clip the microphone to lapel or collar.
For optimal sound, position the
microphone as close to the mouth as
possible.
Headset Microphone Placement
Several varieties of headset
microphones are available. Simply
connect the microphone cord directly
into the jack on top of the transmitter
and place the headset around the
back of the head. For optimal sound,
position the microphone at the corner
of the mouth.
18
5. Warranty, Safety
& Specifications
8. CHANNEL SELECTION: BELT-PACK
TRANSMITTER
Channel Selection:
4. Troubleshooting
Once a channel has been selected on
the receiver, you now need to select
that same channel on the Belt-pack
transmitter.
1. Turn the transmitter power ON by
sliding the PWR button to ON.
2. Setup & Use
3. Optional
Accessories
2. Open the battery compartment
door by depressing the latches on
each side of the transmitter.
1. Overview
3. Use the screwdriver channel set
to switch to the current channel
shown on the receiver.
Transmitters and receivers are
available in 3 different frequency
groups (620, 645, 670 MHz). Verify that
the frequency group of the receiver
matches the letter code on the silver
sticker in the battery compartment of
the transmitter.
Model Number: BP016
Serial Number
BP01614324024
FREQUENCY 670 MADE IN TAIWAN
19
5. Warranty, Safety
& Specifications
9. GAIN ADJUST ON BELT-PACK
TRANSMITTER
4. Troubleshooting
Gain Adjust:
When changing microphones or
users, it may be necessary to adjust
the transmitter gain based on
differing microphones sensitivities
and voice levels.
1. Open the battery compartment
door by depressing the latches on
each side of the transmitter.
2. Turn the MT dial clockwise
to increase the gain and
counterclockwise to decrease the
gain.
1. Overview
2. Setup & Use
3. Optional
Accessories
To adjust the gain:
NOTE: If you are using a high
impedance source, such as a guitar,
it will be necessary to adjust the GT
dial. Using a high impedance source
requires a special cable. Contact
Lightspeed Customer Service at 800732-8999 for more information.
20
5. Warranty, Safety
& Specifications
10. BATTERY LIFE INDICATOR AND TYPE ON
BELT-PACK TRANSMITTER
Battery low indicator is located next
to the power switch. It glos red
when the battery charge is low and
recharging is necessary.
4. Troubleshooting
Battery Life Indicator
2. Setup & Use
The transmitter will operate with
either standard AA alkaline batteries
or nickel metal hydride (NiMH)
rechargeable batteries. Since these
types of batteries have different
characteristics, it is important not to
mix battery types. use only AA NiMH
batteries when recharging.
3. Optional
Accessories
Battery Type
WARNING: Do not use NiCad
batteries! They will not charge
properly and may cause damage to
the transmitter.
Lightspeed recommends Panasonic
or Energizer batteries. Duracell may
not work.
1. Overview
NOTE: Do not mix battery types.
21
5. Warranty, Safety
& Specifications
11. REPLACING BATTERIES IN BELT-PACK
TRANSMITTER
1. Overview
2. Setup & Use
3. Optional
Accessories
4. Troubleshooting
Replacing the Batteries:
22
1. Open the battery compartment
door by depressing the latches on
each side of the transmitter.
2. Remove or replace the batteries
and snap the door shut. The
belt-pack requires two AA sized
batteries.
3. Note the polarity in the battery
compartment.
IMPORTANT: Replace batteries
with the same type, (alkaline or
NiMH), that were installed in your
Handheld Microphone. Lightspeed
recommends Panasonic or Energizer
batteries. Duracell may not work
properly.
WARNING: Do not attempt to
charge alkaline batteries. They can
overheat and expand, creating a
significant hazard and damaging the
transmitter. (This is not covered by
warranty.)
1. Switch the transmitter power OFF.
2. Insert the small DC plug into the
jack on the side of the transmitter.
5. Warranty, Safety
& Specifications
4. Troubleshooting
Make sure there are NiMH rechargeable batteries in the transmitter
before plugging in the charger.
Typical battery life is about 8 hours.
Fully charged Lightspeed transmitters
will last over 7 hours. A full charge will
be attained in 8-10 hours.
3. Optional
Accessories
Recharging the Batteries
(NiMH Rechargeable Batteries ONLY):
2. Setup & Use
12. RECHARGING BATTERIES IN BELT-PACK
TRANSMITTER
4. The RED LED on the charger will
light, indicating that charging is in
progress.
5. When the batteries are fully
charged, the LED on the charger
will glow GREEN.
1. Overview
3. Plug the other end of the charger
into any standard 110 VAC outlet.
23
5. Warranty, Safety
& Specifications
4. Troubleshooting
3. Optional
Accessories
2. Setup & Use
1. Overview
DAILY USE INSTRUCTIONS
1. Wireless Microphone Operation
RF Indicator Lights: When both
the system and the transmitter
are ON and operating on the
same channel you will see a BLUE
glowing RF Indicator Light (either
A or B) on the receiver.
2. VOLUME ADJUSTMENT: While
speaking into the microphone,
slowly turn the RECVR1 volume
knob (or RECVR2, depending
on which microphone you are
operating) clockwise until you
reach the desired level.
NOTE: Do not stand directly in front
of the Delta PA speaker with the
microphone on. This will result in
feedback or ‘squealing.’ It is best to
stand behind or to the side of the unit
when setting volume level.
3. SQUELCH ADJUSTMENT:
Adjusting the squelch level may be
necessary to block out potential
interference in areas that have that
have very high radio traffic.
• Maximum squelch (full clockwise)
reduces reception range but also
reduces the potential for system
interference.
• Minimum squelch (full counterclockwise) increases reception
range, but also increases the
potential for system interference.
NOTE: In most cases it will not be
necessary to adjust the squelch
level. The system already has a clear
channel scanner to take care of most
interference problems.
4. TRANSMITTER LOW BATTERY
INDICATOR: This LED will light
to indicate the batteries in the
corresponding transmitter are
low and need to be replaced or
recharged.
24
RECVR 2
RECVR 2
RECVR 2
O/I
POWER/
RECVR 1
POWER
RED: LOW BATT
RECVR 2
GREEN: ON
CHARGE
RED: CHARGING
GREEN: FULL
O/I
POWER/
RECVR 1
POWER
RED: LOW BATT
GREEN: ON
CHARGE
RED: CHARGING
GREEN: FULL
RECVR 1
RECVR 1
OPTIONAL ACCESSORIES
3. Optional
Accessories
4. Troubleshooting
HANDHELD MICROPHONE TRANSMITTER
5. Warranty, Safety
& Specifications
SECTION 3:
1. RED LED: Lights up briefly when
power is switched on, flashes
continuously when audio is muted.
1. Overview
2. Setup & Use
ON
2. POWER ON/OFF: Turns the audio
ON and OFF. The RED LED will
flash when power is turned ON.
3. CHANNEL SWITCH: A
screwdriver adjust to set channel
1-16 to match the channel setting
of its receiver.
4. BATTERY COMPARTMENT:
Bottom section of microphone
barrel unscrews to reveal battery
compartment.
25
5. Warranty, Safety
& Specifications
3. Optional
Accessories
4. Troubleshooting
BELT-PACK TRANSMITTER
1. Overview
2. Setup & Use
1. ON/OFF BUTTON
2. RED LED: Lights up briefly when
power is switched ON, flashes
continuously when audio signal is
muted.
3. MICROPHONE JACK: Microphone
connects to transmitter here.
4. ANTENNA
5. BATTERY CHARGER JACK:
Optional battery charger plugs in
here (for NiMH batteries only.)
6. DOOR LATCHES: Press both
latches to open the battery
compartment door.
26
10
7. GT (TRANSMITTER GAIN):
Provides adjustment for differing
voice levels and microphone
sensitivities.
8. MT (MICROPHONE GAIN):
Provides adjustment for differing
voice levels and microphone
sensitivities.
9. CHANNEL SET SWITCH:
Screwdriver adjust to set the
channel 1-16 to match its receiver
channel.
10. BATTERY COMPARTMENT
No sound when someone speaks
into the wireless microphone:
1. Delta PA power should be ON.
The GREEN LED should be lit. If
it does not light when the system
is switched on, make sure the AC
power supply is plugged in.
2. Microphone/transmitter power
should be ON. If the low battery
indicator is on (red) the batteries
are most likely too weak. If the
batteries are rechargeable, plug
the microphone/transmitter into
the charger. If the batteries are
alkaline, replace them with new
alkaline batteries
WARNING: Do not attempt to
charge alkaline batteries. They can
overheat and expand, creating a
significant hazard and damaging
the warranty. (This is not covered by
warranty.).
3. The transmitter and receiver
should be set to the same channel.
The BLUE RF LED (A or B) should
be lit.
4. Make sure the MUTE light is not
flashing. Switch the transmitter/
microphone off of MUTE.
5. Verify that receiver and transmitter
are in the same frequency group.
Turn the Delta PA OFF and then
ON again. The letter code from
the frequency group will blink
on the receiver module. Open
the battery compartment on
the transmitter and be sure that
frequency group printed on the
sticker matches the frequency
group letter code that blinked
when the Delta PA powered ON.
If the letters are different, find
a microphone or belt-pack with
the same frequency group as the
receiver indicates when the Delta
PA is turned ON.
The wireless mic is experiencing
drop-out or interference:
1. The wireless frequency being used
may not be a clear channel. Turn
the transmitter OFF and press
the SCAN button on the receiver
to find a clear frequency. Then
select the same channel on the
transmitter.
2. Transmitter is out of range of
receiver. The transmitters have a
maximum range of about 300-350
feet in an open field environment.
This range can be dramatically
reduced indoors and outdoors
when large objects (such as a
wall) may be obstructing the path
directly between transmitter and
receiver. If so, position the two
closer together.
3. Batteries are very weak. Right
before the batteries are about
to die, the overall performance
of the system can be drastically
lessened. Check the battery status
of the transmitter.
Low Volume or Feedback:
5. Warranty, Safety
& Specifications
4. Troubleshooting
Note: Most problems are directly related to low battery power. Please run
through the “Battery Check” items first. For remaining troubleshooting, use
known good, fully-charged batteries.
3. Optional
Accessories
COMMON PROBLEMS AND SOLUTIONS
2. Setup & Use
TROUBLESHOOTING
1. Overview
SECTION 4:
1. Ensure microphone is positioned
appropriately.
2. Check volume level on the
amplifier. If the volume is too
high, feedback will occur. Adjust
accordingly.
If you review these instructions and still have questions, write down the
serial number and model number of your system and call Lightspeed
Technical Services at 800.732.8999, 5 a.m. – 5 p.m., PST.
27
5. Warranty, Safety
& Specifications
WARRANTY, SAFETY &
SPECIFICATIONS
Lightspeed Classroom Audio Systems
are guaranteed against malfunction
due to defects in materials and
workmanship for a period of THREE
(3) YEARS, beginning at the date
of the purchase invoice. If such
malfunction occurs, the product
will be repaired or replaced (at
Lightspeed’s option) without charge
during the warranty period, subject to
the following conditions:
1. The product must have been
purchased from an authorized
Lightspeed Technologies Dealer or
representative.
1. Overview
3. Optional
Accessories
THREE-YEAR LIMITED WARRANTY
2. Setup & Use
4. Troubleshooting
SECTION 5:
2. Lightspeed Technologies must
perform all warranty service.
Any service performed without
the authorization of Lightspeed
Technologies will void the entire
warranty.
3. This warranty does not cover any
product that has been subjected
to negligent use, connection to
improper power source, misuse, or
operated beyond its manufactured
specifications and limits, or has not
been reasonably maintained.
4. Warranty shall not apply to alkaline
or NiMH batteries, exterior finish,
AC power cords, bulbs, or any
other failings due to normal wear.
5. Warranty is void when equipment is
subjected to adverse temperature,
humidity, moisture, or other
conditions that are not considered
normal environmental conditions.
6. This warranty excludes all damages
or defects caused by shipping,
transporting, or inadequate
packaging for shipping.
7. Customers are responsible for
freight charges to Lightspeed
Technologies for service.
Lightspeed Technologies will pay
for return freight to the end user
by most reasonable method.
The warranty period for each system
and component type is listed below:
Delta PA: Six (6) years from the date
of original purchase.
RF Wireless Transmitters and
Receivers: Three (3) years from the
date of purchase.
Batteries: One (1) year from the date
of purchase.
Microphones and Cases: One (1) year
from date of purchase.
Products will be replaced or repaired
at Lightspeed Technologies’ option
during the
warranty period.
For warranty service, please contact Lightspeed Customer Service Department
to obtain return authorization approval and an RA number.
Our Service Department (800.732.8999, 5 a.m. – 5 p.m., PST)
will handle all your repair/replacement needs.
28
5. Warranty, Safety
& Specifications
SAFETY WARNINGS
This product is listed to UL standards
and requirements for electrical safety by
Underwriters Laboratories Inc.
FCC Caution
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
3. Optional
Accessories
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
2. Setup & Use
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure, that may be sufficient magnitude to
constitute a risk of electric shock.
4. Troubleshooting
LIGHTSPEED TECHNOLOGIES, INC. PH: 1.800.732.8999
DELTA PA & BP016 & HM016 ：
IC ID Caution
1. Overview
To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment. (Example - use
only shielded interface cables when connecting to computer or
peripheral devices).
This device complies with Industry Canada licence-exempt RSS-123
standard.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
BP016 & HM016 ：
FCC Caution
THIS DEVICE COMPLIES WITH PART 74 OF THE FCC RULES.
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment.
29
5. Warranty, Safety
& Specifications
4. Troubleshooting
3. Optional
Accessories
2. Setup & Use
1. Overview
30
SYSTEM SPECIFICATIONS
OVERALL SPECIFICATIONS
Nominal SPL [1W/1M]
Maximum SPL
System Power [RMS]
Music Power [RMS]
Amplifier Type
Frequency Response of amplifier
Speaker System
Microphone Input
Wireless Microphones
Line Input
Line Output
Tone Controls
Speaker Output
Dimensions [H x W x D inches]
Weight
89 dB
102 dB
30 W at 2 Ω
40 W at 2 Ω
Analog Class AB
90 Hz - 18 kHz
Full-Range 6.5”/4 Ω
¼ inch phone jack
Up to two 100-Channel UHF True
Diversity
3.5 mm
3.5mm and ¼ inch
Bass and Treble
1 switched 2 Ω
9.75 x 12.5 x 6.25
7.2 lbs./20.4 kg
Micro Frequency Range
Selectable Frequencies
Deviation
Sensitivity
Tone-code Frequency
Image Rejection
S/N Ration [Max]
TRANSMITTER SPECIFICATIONS
HM-016 Handheld Microphone
RF Power Output
50 mW Maximum
Spurious Emission
Macro Frequency Range
>60 dB below the carrier
620 MHz to 694.75 MHz
[3 Macro-Groups]
Selectable Frequencies
Tone-Code Frequency
Pre-Emphasis
Limiter Range
Battery Type
Battery Life [Alkaline]
Weight w/o Batteries
16
32.768 KHz
50 µsec
>30 dB or audio overload
2 AA
Approx. 8 Hours
4.2 oz/120 g
BP-016 Belt-pack
RF Power Output
Spurious Emission
Macro Frequency Range
Selectable Frequencies
Tone-Code Frequency
Pre-Emphasis
Limiter Range
Battery Type
Battery Life [Alkaline]
Microphone Connector
Weight w/o Batteries
50 mW Maximum
>60 dB below the carrier
620 MHz to 694.75 MHz
[3 Macro-Groups]
16
32.768 KHz
50 µsec
>30 dB or audio overload
2 AA
Approx. 8 Hours
TA4F
3 oz/85 g
5. Warranty, Safety
& Specifications
4. Troubleshooting
Macro Frequency Range
Microprocessor Controlled
PLL Synthesized
620 ti 694.75 MHz
[3 Macro-Groups]
25 MHz each Macro-Group
100
± 40 KHz Nominal
-100 dBm at S/N ratio of >80 dB
32.768 KHz
>85 dB
>105 dB
3. Optional
Accessories
Carrier System
2. Setup & Use
RECEIVER SPECIFICATIONS
1. Overview
SYSTEM SPECIFICATIONS CONT’D
CHANNEL FREQUENCY ASSIGNMENT
EE
HH
LL
620.000 - 639.750
640.000 - 659.750
660.000 - 679.750
31
LI GHTSPEED TE C HNOL OG I E S
11509 S W HERM A N R O A D / TUA L ATIN , O R 9 7062
TOLL F REE: 80 0 .7 3 2 .8 9 9 9 / PHO N E : 5 0 3 .6 8 4 . 5538 / FAX : 503. 684. 3197
LIGHTS PEED-T E K.CO M
MN0374US01-0
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-702
Instance ID                     : uuid:47bbbc62-fa6f-4982-a836-6ba333f2d6ae
Document ID                     : xmp.did:1EF8DFFDBA2068118A6D9DB7E1EFB4F8
Original Document ID            : adobe:docid:indd:993ec0ad-22e1-11df-b09b-d2d71210f68c
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:33A1F3F7BA2068118A6D9DB7E1EFB4F8
Derived From Document ID        : xmp.did:84392BD9472068118C1496FDDFE0B8F7
Derived From Original Document ID: adobe:docid:indd:993ec0ad-22e1-11df-b09b-d2d71210f68c
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:333E64C119206811871FDF60399BAD91, xmp.iid:343E64C119206811871FDF60399BAD91, xmp.iid:71DA78801B206811871FDF60399BAD91, xmp.iid:9DEE151C1D206811871FDF60399BAD91, xmp.iid:916EE2911D206811871FDF60399BAD91, xmp.iid:39E12CB61D206811871FDF60399BAD91, xmp.iid:6D660C3A1F206811871FDF60399BAD91, xmp.iid:808E8D631F206811871FDF60399BAD91, xmp.iid:8729ECF71F206811871FDF60399BAD91, xmp.iid:D322DD74072068118F62B0AEB1E5E8B0, xmp.iid:681D5ADA072068118F62B0AEB1E5E8B0, xmp.iid:691D5ADA072068118F62B0AEB1E5E8B0, xmp.iid:EC6ED7340A2068118F62B0AEB1E5E8B0, xmp.iid:3C3456730A2068118F62B0AEB1E5E8B0, xmp.iid:9BEDA6BC0B2068118F62B0AEB1E5E8B0, xmp.iid:3601252F0C2068118F62B0AEB1E5E8B0, xmp.iid:FD8D9F3C0C2068118F62B0AEB1E5E8B0, xmp.iid:AE2D56740720681188C6BFE402B79204, xmp.iid:D119D1F60B20681188C697A819296DA4, xmp.iid:E72D8D310C20681188C697A819296DA4, xmp.iid:77ECAE74072068118A6DC5F994FDF118, xmp.iid:AFB735C5072068118A6DC5F994FDF118, xmp.iid:9BA1B13E082068118A6DC5F994FDF118, xmp.iid:F77F117407206811871FD3901D863C74, xmp.iid:48A65C7407206811871FD3901D863C74, xmp.iid:F77F1174072068118C14ABBBBA1EC7DB, xmp.iid:62224974072068118C14ABBBBA1EC7DB, xmp.iid:3153A2740720681188C6AAE3FF988121, xmp.iid:8B6302930820681188C6AAE3FF988121, xmp.iid:691470920A20681188C6AAE3FF988121, xmp.iid:B7A92A140C20681188C6AAE3FF988121, xmp.iid:CD3105100E20681188C6AAE3FF988121, xmp.iid:02D453200E20681188C6AAE3FF988121, xmp.iid:9FB825CE1520681188C6AAE3FF988121, xmp.iid:32B17CAF1B20681188C6AAE3FF988121, xmp.iid:ECD02BA81C20681188C6AAE3FF988121, xmp.iid:6CFA43ED1C20681188C6AAE3FF988121, xmp.iid:66576B111D20681188C6AAE3FF988121, xmp.iid:8C1E3D982E20681188C6C2551CC56389, xmp.iid:B29E1CA23220681188C6C2551CC56389, xmp.iid:733D274A462068118C1496FDDFE0B8F7, xmp.iid:1DAA8ABF472068118C1496FDDFE0B8F7, xmp.iid:1EAA8ABF472068118C1496FDDFE0B8F7, xmp.iid:84392BD9472068118C1496FDDFE0B8F7, xmp.iid:C63C120C482068118C1496FDDFE0B8F7, xmp.iid:31A1F3F7BA2068118A6D9DB7E1EFB4F8, xmp.iid:32A1F3F7BA2068118A6D9DB7E1EFB4F8, xmp.iid:33A1F3F7BA2068118A6D9DB7E1EFB4F8, xmp.iid:1EF8DFFDBA2068118A6D9DB7E1EFB4F8, xmp.iid:6F3F8074072068118A6DEFE74E1F053B, xmp.iid:9674D46F5F2068118A6D80D068D62927
History When                    : 2010:11:05 19:39:53-07:00, 2010:11:05 19:39:53-07:00, 2010:11:05 19:52:24-07:00, 2010:11:05 20:03:54-07:00, 2010:11:05 20:07:12-07:00, 2010:11:05 20:08:13-07:00, 2010:11:05 20:19:03-07:00, 2010:11:05 20:20:13-07:00, 2010:11:05 20:24:22-07:00, 2010:11:09 19:23:32-08:00, 2010:11:09 19:26:22-08:00, 2010:11:09 19:32:09-08:00, 2010:11:09 19:43:13-08:00, 2010:11:09 19:44:58-08:00, 2010:11:09 19:54:10-08:00, 2010:11:09 19:57:22-08:00, 2010:11:09 19:57:45-08:00, 2010:11:09 20:31:05-08:00, 2010:12:14 11:31:41-08:00, 2010:12:14 11:33:20-08:00, 2010:12:14 11:56:33-08:00, 2010:12:14 11:58:48-08:00, 2010:12:14 12:02:12-08:00, 2011:02:15 20:47:59-08:00, 2011:02:15 20:48-08:00, 2011:03:27 22:28:36-07:00, 2011:03:27 22:28:36-07:00, 2011:03:28 21:20:55-07:00, 2011:03:28 21:28:56-07:00, 2011:03:28 21:43:14-07:00, 2011:03:28 21:54:01-07:00, 2011:03:28 22:08:13-07:00, 2011:03:28 22:08:40-07:00, 2011:03:28 23:03:39-07:00, 2011:03:28 23:45:44-07:00, 2011:03:28 23:52:42-07:00, 2011:03:28 23:54:38-07:00, 2011:03:28 23:55:38-07:00, 2011:04:15 15:37:33-07:00, 2011:04:15 15:37:33-07:00, 2011:04:19 17:04:38-07:00, 2011:04:19 17:15:05-07:00, 2011:04:19 17:15:47-07:00, 2011:04:19 17:15:48-07:00, 2011:04:19 17:17:13-07:00, 2011:04:29 09:51:16-07:00, 2011:04:29 09:51:16-07:00, 2011:04:29 09:51:26-07:00, 2011:04:29 09:51:26-07:00, 2011:04:29 12:37:45-07:00, 2011:05:04 15:21:58-07:00
History Software Agent          : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /;/metadata
Create Date                     : 2011:05:04 15:22:12-07:00
Modify Date                     : 2011:05:09 20:46:40+08:00
Metadata Date                   : 2011:05:09 20:46:40+08:00
Creator Tool                    : Adobe InDesign CS5 (7.0.4)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 6517 bytes, use -b option to extract), (Binary data 2961 bytes, use -b option to extract)
Doc Change Count                : 3913
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 32
Creator                         : Adobe InDesign CS5 (7.0.4)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ORV-HM016

Navigation menu