Manual
LINNO LAMPS
MESH NETWORKING
SMART DEVICE APP
SENSING CALCULATION S/W
CONTROLLER S/W & SERVER
RECEIVE DATA & MONETIZE
REMOTE
CONTROL
SMART SENSOR
MESH NETWORKING
HOW IT WORKS
LINNO LAMPS
MESH NETWORKING
SMART DEVICE APP
SENSING CALCULATION S/W
CONTROLLER S/W & SERVER
RECEIVE DATA & MONETIZE
REMOTE
CONTROL
SMART SENSOR
MESH NETWORKING
Group 1 Group 2
window
WHAT SMART SENSOR SCEANARIO IS
LINNO LAMPS
MESH NETWORKING
SMART DEVICE APP
SENSING CALCULATION S/W
CONTROLLER S/W & SERVER
RECEIVE DATA & MONETIZE
REMOTE
CONTROL
SMART SENSOR
MESH NETWORKING
window
WHAT SMART SENSOR SCEANARIO IS
LINNO LAMPS
MESH NETWORKING
SMART DEVICE APP
SENSING CALCULATION S/W
CONTROLLER S/W & SERVER
RECEIVE DATA & MONETIZE
REMOTE
CONTROL
SMART SENSOR
MESH NETWORKING
window
WHAT SMART SENSOR SCEANARIO IS
LINNO LAMPS
MESH NETWORKING
SMART DEVICE APP
SENSING CALCULATION S/W
CONTROLLER S/W & SERVER
RECEIVE DATA & MONETIZE
REMOTE
CONTROL
SMART SENSOR
MESH NETWORKING
brightness
70%
brightness
70%
window
WHAT SMART SENSOR SCEANARIO IS
LINNO LAMPS
MESH NETWORKING
SMART DEVICE APP
SENSING CALCULATION S/W
CONTROLLER S/W & SERVER
RECEIVE DATA & MONETIZE
REMOTE
CONTROL
SMART SENSOR
MESH NETWORKING
brightness
10%
brightness
50%
window
WHAT SMART SENSOR SCEANARIO IS
1
2
3
4
5
6
6
HIGH EFFICIENCY
LIGHT
FOR SPACE
Space and light's efficiency
6
SECURITY MODE
FOR USER
Upgrade security
360 120
MOTOIN SENSOR
LIGHT SENSOR
LUX CONTROL MOOD LAMP
SECURITY 3 PIR SENSOR
For large Space
1 PIR SENSOR
For Small Space
.. !!
ITEM : SMART SENSOR
Specifications
1) Operating voltage: AC 110 V
2) Communication Method: Wireless (Bluetooth)
3) Operating distance: 10 M
4) Output: Max +10 dBm
5) Receive sensitivity: -102 dBm typ.
6) Operating frequency
Send: 2.402 ~ 2.480 MHz, 2.4G ISM band
Reception: 2.402 ~ 2.480 MHz, 2.4G ISM band
7) Channel: 40 channels
8) Modulation scheme: GFSK
9) Channel spacing: 2 MHz
10) Profile: Bluetooth Ver 4.0
11) Protocol: Asynchronous serial communication
12) Size: 85 X 85 X 26 mm
13) Weight: About : 150 g
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation
IMPORTANT NOTE:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 Cm from
all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this equipment near water.
6) Do not using near any heat sources such as radiators, heat resisters, stove, or other equipment that produce
heat.
CONTACT INFORMATION
Manufacturer Address : 96-22, Yangji-ro 281beon-gil, Onam-eup, Namyangju-si, Gyeonggi-do, Korea
To locate in-country Linno Inc., distributors of the SSL3
please refer to the Linno Inc. Website http://linno.co.kr/
These distributor(s) represent local contacts for this product.
CORPORATE HEADQUARTERS:
Linno Inc
96-22, Yangji-ro 281beon-gil, Onam-eup, Namyangju-si, Gyeonggi-do, Korea
Tel: +82-2-546-9820
Fax: +82-2-546-9622
Web: http://linno.co.kr/
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is Subject to the following two condition: (1) this device may not cause interference
,and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.