Lionda Technology Co M41001 900 MHz Analog Cordless Phone with Speakerphone User Manual FCC Information and End

Download:
Mirror Download [FCC.gov]
Document ID	138420
Application ID	ewweJ48sUvVqoT2GiKr1EA==
Document Description	FCC Information and End
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	66.48kB (830994 bits)
Date Submitted	2001-02-28 00:00:00
Date Available	2001-02-28 00:00:00
Creation Date	2001-01-04 16:10:56
Producing Software	Acrobat 3.0 Scan Plug-in
Document Lastmod	2001-01-04 16:11:55
Document Title	FCC Information and End
Document Creator	Acrobat 3.0 Scan Plug-in

[HE fit Mi
Recharging the ttery Pack
Battery Type
Use the following type and size of battery pack:
Cordless Telephone Battery Pack
3.6V. 600 mAh
U.$. Electronics Inc.
Ni-Cd Battery Pack: model 8650
This battery pack is available through:
us. Electronics Service Center
105 Madison Avenue
New York, NY 10016
1-800-828-5208
Recharging the Battery Pack
The nickel cadmium (Ni~Cd) battery pack in the HANDSET can be recharged many
times using the built-in chargerin the BASE UNIT.
When the BATTERY LOW indicator star1s to blink. a “beep‘ sound will be heard
every 12 seconds This indicates that the battery pack needs to be recharged
vCharge the battery pack at least once every 90 days of nonuse to avoid battery
failuret When the battery pack can no longer be charged. replacement oi the
battery pack will be necessary,
The battery pack used in your telephone may develop a condition known as
“MEMORYfl Once subjected to a regular short discharging routine. the battery
assumes the discharging pattern it was subjected to This is known as a ‘MEMORY'
condition which causes rapid discharging thereby shortening the battery paokcharge
span. If you believe your battery pack has developed a memory condition, do not
charge the HANDSET unfil the BATTERY LOW indicator oomes on. When it does
come on, charge the HANDSET fully for 12 hours.
IMPORTANT
Plziring your BASE UNIT rieai apriiiniices
such asteiewsieiis, refrigerators radios, or
microwave ovens may cause interference
sou~Eum pm is 4 mm. no A»
“in
Changing the Battery Pack
The battery pack provides power for the HAN Ds ET of your cordless telephone
To Replace the Battery Pack:
Remove the HAN 03 ET battery compartment cover by sliding it down,
Pull out the battery connector and remove the battery pack,
Plug the new battery pack into the battery connector.
Slide the HANDSET battery compartment cover firmly into place in its closed
position.
5. Before use. charge the new battery pack for 12 hours.
PPN?‘
ATTENTION:
The product that you have purchased contains a rechargeable battery pack. The
battery pack is recyclable At the l‘nd of its useful life, under various state and
local laws. it may be illegal to disuose ot this battery pack into the municipal
waste stream. Check with your local solid waste officials for details in your area for
recycling options or proper dispose
lmm
i . owscroa 5mm coummsm
,, —f—~ _ ‘ cos/en
l ,,
xi! ‘
i t r
j i 1 1 l l ‘ 3mm,
lm
H ,
1 E ,”
Remove lhe ballery amuser companmenl
cover by sliding it down.
sowsmnwe 20 MWJJOAM
Problem Solving
Problem Solving Section
For your assistance. we have listed below a lew common problems.
Phone does not work, check the following:
1. BASE UNIT is plugged into power source.
2. HANDSET is charged.
3. TONE/PULSE switch is in the right position.
4. TELEPHONE LINE CORD is plugged into the telephoneiack.
Range ofphone limited, check the following:
1. ANTENNA on BASE UNIT is raised.
2. BASE UNIT is centrally located in your residence.
3. BASE UNIT is not located near appliances.
No dial tone, check the following:
1. Telephone plug is connected to the telephone line.
2. BASE UNIT is plugged into power source.
Received signal flutters or fades, check the following:
1. Battery pack in HANDSET is fully charged.
2. HANDSET is not too far from the BASE UNIT.
3. ANTENNA on BASE UNIT is raised. “ "
Interference on reception, check the following:
1. Noise may be picked up from electrical products at home or electrical storms.
Generally, this noise is a minor annoyance and should not be interpreted as a
defect in your system. (See Technical Information on page 22.)
2. Choose an alternate channel using the button on the HANDSET.
Excess static, check the following:
1. Check to see that the ANTENNA is not touching another metal object.
Raise or reposition the BASE UNIT ANTENNA.
If after pressing the talk button, you receive three beeps and
no dial tone, check the following:
1. BASE UNIT is plugged into power source.
NOTE: It no telephones in the house are working. disconnect one set at a time
to verify that none of the phones are causing the problem. It you still have a
problem after doing this and yourtelephone still does not work. please contact
your local phone company.
DOM-EMA" pmfl 21 I «was. new
|qj 4h —i-|_~
Technical Information
Technical Information
This cordless telephone uses radio frequencies to allow mobility. There are
certain difficulties in using radio frequencies with cordless telephone While
these are normal, the following could affect operation of your system.
Noise
Electrical pulse noise is present in most homes at one time or another This
noise is most intense during electrical storms Certain kinds of electrical
equipment such as light dimmers, fluorescent bulbs, motors, and fans also
generate noise pulses, Because radio frequencies are susceptible to these noise
pulses, you may occasionally hear them in your HANDSET. Generally they are
a minor annoyance and should not be interpreted as a defect in your system,
Range
Because radio frequency is used. location of the BASE UNIT can affect the
operating range. Try several locations in your home or office and pick the one
that gives you the clearest signal to the HAN 05 ET
In terference
t Electronic circuits activate a relay to connect the cordless telephone to your
‘ j r telephone line These electronic circuits operate in the radio frequency spectrum “h
While several protection circuits are used to prevent unwanted signals. there
may be periods when these unwanted signals enter the BASE UNIT You may
hear clicks or hear the relay activate while you are not using the HAN DS ET. If
the interference occurs frequently. it can be minimized or eliminated by lowering
the height of your base antenna or by relocating the BASE UNIT, You can check
for interference before selecting the final BASE UNIT location by plugging in the
phone.
N O TICE:
This cordless telephone uses radio communication between the HANDSET and
the BASE UNIT and may not ensure privacy of communication. Other devices,
including other cordless telephone. may interfere with the operation of this
cordless telephone or cause noise during operation. Units not containing coded
access may be accessed by other radio communication systems Cordless
telephones must not cause interference to any licensed radio service,
IMPORTANT
if you Irve rrr an area winch gels frequent
thunderstorms, we strongly rccorrrmcnd
plugging yourAC adaptor into a surge protector
9034~EMAN pms 22 r 4/1299. no m
FCC Requirements
Federal Communications Commission Requirements
This equipment complies with Part 68 of FCC Rules A label on the BASE UNIT
of this equipment contains. among other information. the FCC Registration
Number and the Ringer Equivalence Number (REN) for this equipment. You
must, upon request, provide this information to your telephone company.
The REN is also useful in determining the quantity of devices that you may
connect to your telephone line and still allow these devices to ring when your
telephone number is called. In most areas, but not all. the sum of the REN‘s for
all devices connected to one line should not exceed five (50). To be certain of
the number of devices that you may connect to your line, you should contact
your local telephone company
If your equipment should cause harm to the telephone network, the telephone
company may temporarily disconnect your service If possible, they will notify
you in advance that temporary discontinuance of service may be required.
However, when advance written notice is not possible. the telephone company
may temporarily discontinue service without notice if such action is necessary
under the circumstances The telephone company may make changes in its
communication facilities. equipment, operations, or procedures where such
,action is reasonably required in the operation of its business and is not inconsis-
tent with the mles and regulations of the Federal Communications Commission.
Do not attempt to repair or modify this equipment.
Warning: Changes or modifications not expressly approved by the party
responsible for its compliance could void the user's authority to operate the
equipment.
Some cordless telephones operate at frequencies that may cause interference
to nearby TVs and VCR’st To minimize or prevent such interference, the base of
the cordless telephone should not be placed on or near a TV or VCR If interfer—
ence is experienced, moving the cordless telephone farther away from the TV or
VCR will often reduce or eliminate the Interference.
This equipment should not be used on loin telephone lines. Connection to party
line service is subject to state tariffs. lf trouble is experienced, disconnect this
equipment from the telephone line to di -termine if it is causing the malfunction. If
the equipment is determined to be maliunctioning. its use should be discon-
nected until the problem has been corn ctedt
9034~EMANM 2: mm. mom
FCC Requirements
Federal Communications Commission Requirements
(continued)
Note: This equipment has been tested and found to comply with the limits for a
class 8 digital device. pursuant to Part 15 of the FCC Rules These limits are
designed to provide reasonable protection against harmful interference in a
residential installation This equipment generates, uses and can radiate radio
frequency energy and, it not installed and used in accordance with the
instructions, may cause harmful interference to radio communications
However, there is no guarantee that interference will occur in a particular
installation If this equipment does cause harmful interference to radio or
television reception. which can be determined by turning the equipment oft and
on. the user is encouraged to try to correct the interference by one of the
tollowing measures
1. Reon'ent or relocate the receiving antenna.
2. Increase the distance between the equipment and the receiverr
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is conner ted.
4. Consult the dealer or an ex: erienced radio/TV technician tor help.
IMPORTANT
Placing your BASE UNIT near appium
such as telewsicns, refrigerators
microwave ovens may Cause interference
sou-Emu me u l «mu: 30m
Warranty
Warranty Information
BellSouth Products
One-Year Limited Warranty
This limited warranty sets forth all BeIISouth Products responsibilities regarding
your product, There are no other expressed or implied warranties from BellSouth
Products.
Warranty Service Provided
If you purchased the new telephone from a retail vendor. BelISouth Products
warrants the telephone against defects in material and workmanship for a period
01 one (1) year from the original date of purchase. This warranty is in lieu of all
other express warranties. This warranty begins when you purchase the telephone
and continues for one (1) year unless you sell or rent the telephone, in which
case the warranty stops.
BeilSouth Products disclaims any implied warranty, including the warranty of
merchantability and the warranty of fitness for a particular purpose, as of the
date of 90 days from your original purchase of the telephone. BelISouth
' Products assumes no responsibility for any special, incidental, or consequential
damages.
t This warranty gives you specific legal rights and you mayhave other rights which
vary from state to state. Some states do not allow the exclusion or limitations of
special, incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitation may not apply to you.
Warranty Service Not Provided
This warranty does not cover damage I esulting from accident, misuse, abuse.
improper installation or operation. lack 1 it reasonable care, unauthorized
modification, the affixing of any attachn rent not provided by BellSouth Products
with the telephone and/or loss of parts This warranty is voided In the event any
unauthonzed person opens. alters or rt pairs the telephone All BellSouth
equipment being returned for repair must be suitably packaged. Telephone
companies use different types of equipi nent and offer various types of services to
customers BeIlSouth Products does not warrant that this telephone is
compatible with the type of equipment 4 if any particular telephone company or
the services provided by it.
sun-swim we 25 i 4mm, 9:30 AM
Warranty
he
What to Do for Warranty Service
During the first thirty (30) days, a defective product is eligible for over-the-counter
exchange at the retailer from whom it was purchased. After thirty (30) days. the
defective product should be returned to the authorized service center. Please
allow 2-3 weeks for the return of your telephone product. The shipping address of
the authorized service center is:
U.S, Electronics Service Centei
105 Madison Avenue
New York, NY 10016
NOTE: A product received which Vt as not made for BeIISouth Products or
which is not defective as determinr d by our test procedures will not be repaired
and will be returned CTO.D., freight
To Obtain Warranty Service
~ Provide proof of the date of pun hase within the package.
' Prepay all shipping costs to the authorized service center.
- Include a return shipping addre :s within the package.
‘r v Please retain your sales receipt, tl e canon, the packing materials, and the 4+“
printed material. The original carto 1 is the best shipping container for the
telephone should you have to retul n it
For your reference:
Serial number
Date of Purchase
Name of Dealer
Customer Service Telephone Number:
1-800-210-8950
OUTSIDE THE U.S.A. CALL 1-212-242-6978
90»sz we 2s ‘ 4mm. no m
9034~EMAN,pme 27 «mm, mo 1“
strum.”
This page serves as a template for attachment of screws to the
wall when mounting this telephone on the wall.
1 Cut out this page
Z Use this template to determine the distance between screws
when mounting this phone on the wall.
The two cross hairs identify where to attach the screws.
a i mane new
sou-mm pma
IMPORTANT
In orderto get maximum Itfe from the HANDSET
battery pack be sure to charge the HAN DSET
Ior 12 hours before rnttial use.
IMPORTANT
PIacrng your BASE UNIT near apleances
such as teIevisions, refrigerators, radios, or
microwave ovens maycausemterference.
IMPORTANT
When you hear Interference press the m
button to change the operattng channel
IMPORTANT
The AC ADAPTOR must aIways be ptugged
Into an electricaI outlet
IMPORTANT
To obtatn the best receptton, be sure to
ratse or reposttlonthe BASE UNIT antenna.
I M PO RTA N T
II you trve m an area whlch gets Irequent
thunderstorms we stroneg recommend
pIugging yourAC adaptorlntu a surge protector
a 4mm. mom
Make certain you receive the best
performance from your telephone.
Read this manual first.
@ BELLSOUTH
umm m M can

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:01:04 16:11:55+08:00
Create Date                     : 2001:01:04 16:10:56+08:00
Creator                         : Acrobat 3.0 Scan Plug-in
Producer                        : Acrobat 3.0 Scan Plug-in
Page Count                      : 12

EXIF Metadata provided by EXIF.tools