Lionel RTPGRXV3 Thomas & Friends Ready to Play Set User Manual

Lionel L.L.C. Thomas & Friends Ready to Play Set

Contents

User Manual

      Mobile Bluetooth Sensor  User Manual        This  manual  does  not  contain  the  full  content  of  the function of the mobile Bluetooth sensor, please prevail in kind. Future changes to the  contents  of  the manual  will no  longer  be  individually  informed  of  the user. Please read  the  entire  manual  carefully  and  follow  the instructions.  Product model: ITL-DK6500A Last revision date: 29 September 2016
  Chapter I    Summary 1.1 Product Introduction Mobile Bluetooth Sensor using Bluetooth 4.0 Technology to realize the access control for door and elevator through data communication with Mobile APP.  Pic 1.1 Product diagram  1.2 Specifications  Power supply: DC 24V.  Working Currents: <100mA.  Usage Environment: Temperature:-10~60℃. Relative Humidity: 20%~90% non-condensing.  Storage Environment:
  Temperature: -20~70℃. Relative Humidity: 20%~90% non-condensing.  System Version: Android4.3 +, IOS7.0+  Communication  Distance:  0~10M,  there  are  some errors in different environment  Responsive Speed: 0~3S for IOS,Android is related to mobile phone.  RS485 external communication interface, Transformat : 9600bps,8,N,1.  External Dimension: L120*W100*H21.34mm.  ChapterⅡ    Hardware Instruction 2.1 P1—connect with Access Controller  Interface This interface is connected via shielded cables to the 24V power terminals and to the access control elevator or door, as described below:    Chart 2.1 Connected with access controller interface P1 Interface Instruction GND Negative Power output   24V Positive Power Input 485G 485 Ground Port 485A 485 A port 485B 485 B Port  2.2 SW1— Device DIP Setting The  DIP SW1.1  and  SW1.2  are  used  to  set  the  Mobile
  Bluetooth  Sensor  number,  if  the  access  controller connected with two or more sensors,The setting of SW1 of each device are different,specific setting described as below: Chart 2.2 Device DIP setting SW1.2 SW1.1 Implication OFF OFF 1st Sensor OFF ON 2nd Sensor ON OFF 3rd Sensor ON ON 4th Sensor  SW1.3  and  SW1.4  are  reserved  to  extension function,factory default is OFF. 2.3 LED1/LED2—Indicator Light instruction  Chart 2.4    LED instruction LED1/LED2 Implication The light is always on Unauthorized device or device fault Light Flash Rapidly (100ms/ times) Failed  communication with the controller Light Flash Slowly (1S/time) The  device  Bluetooth  is working properly  ChapterⅢ  User APP Instruction Mobile Bluetooth Sensor using Bluetooth 4.0 technology, it requires the mobile version should be Android 4.3 above or IOS 7.0 above.
  Users need to download our APP for application, you can directly scan the following QR code or search “Jia-R”in the Application Store for download and installation.  Pic 3.1 Jia- R App QR Code  Chapter IV  Instruction After  connecting  the  main  controller  with  the  mobile Bluetooth Sensor , power on the main controller, initialize the device, and download the corresponding parameters Device Authorization The mobile Bluetooth sensor have to be authorized again after  its  first  use  and  initialization.  The  authorized operation  setting  by  APP  and  completed  under  the guidance of our engineering staff.
  Installation and Register of App After  the  installation  of  user  APP,  open  the  APP  and register  through  user’s  mobile  number  and  verification message,  we  suggest  that  user  using  current  mobile number for registering  Authorization via Administrator For registered users, you must be authorized by the administrator in the background through the cloud user rights information which will be synchronized to the phone terminal, you can see the device permissions. If you can not see the authorized device icon after authorization, you can quit the App to log in again. Access modes The  APP  supports  three  access  modes  :  Manual  click, Auto-sensing and shake mode , Login the APP and enter the setting menu and do the modification of access mode as you like.  Manual  Click:When  user  enters  area  around  the mobile Bluetooth Sensor, the mobile app can detect the device,  and  the  icon  of  the  corresponding  device  is lighten, just manually click the icon, then the App will connect with the device and send the control signal to the sensor device to approve the access  Auto-sensing:After user turns on the auto-sensing mode, he or she enters area around mobile Bluetooth Sensor, the APP can detect the device and automatically connect and send the control signal to the device for access approval.                           NOTE: it will automatically turn on the device once from Non-sensing area into the sensing area, if you need to
  open repeatedly, you can use manual click or shake mode.  Shake  Mode:Shake  mode  and  manual  click  mode are similar, but the trigger from click to shake mode.  Chapter V    Device Installation and Debug 5.1 Precautions  Mobile Bluetooth sensor can be used for access control or  elevator  equipment,it  can  be  mix  used  with  the standard  split  access  reader  or  elevator  reader, controlling the same door or same elevator and does not affect the original functions of elevator.  As to the RS-485 communication, in order to ensure the communication quality, it requires double-shielded twisted-pair RVVP * 0.75m㎡ cable, the connection distance with controller should be limited within 50 meters  Due to the Bluetooth interfered by the metal environment, please try to install the device away from the metal environment.  5.2 Device Installation Position The  Mobile  Bluetooth  Sensor  can  be  installed  in  the exposed position or hidden installation. It depends on the construction site and customer requirements.  Normally  the  device  installed  around  gate  for access control.
   Device  installed  around  the  elevator  Hall  for calling elevator system.  Device installed hidden on the top of lift for floor access control.  5.3 Wiring and Debug P1 is connected with the controller interface, the P1 is connected to the controller 485 reader interface. NOTE:   485A and 485B do not reverse. Re-power the equipment after connection, other connections and debugging can refer to the previous indication  Chapter VI Trouble-shootings Here are  some possible  phenomena and simple ways to check them. Please cut off power before any operation on the hardware. Symptom 1: App is unable to detect device normally Possibility:  Please confirm if the device is authorized or not,     if not, please do the authorization for device by APP.  If the indicator LED flash rapidly, it maybe the       abnormal state of controller communication, please check the wiring, if it is working abnormally, try to connect the terminal resistance.  The mobile version too low with poor Bluetooth     compatibility, please try to change another mobile phone for testing.  Bluetooth signal is interfered or blocked by
  environment,please try to change the installation site or search device closely.  Symptom2: Manual click unsuccessfully or open failed Possibility:  No authorization,please confirm you click device is authorized.  Out  of  the  sensing  range  (Display  icon  is  in  black color),  gradually  close  to  the  device (till  the  display icon turn into white color)  Mobile  system  version  too  low with  poor  Bluetooth compatibility, try to change another mobile phone.  Restart mobile phone  Chapter VII Regulatory Note:This  equipment  has  been  tested  and  found  to comply  with  the  limits  for  a  Class  B  digital  device, pursuant  to  part  15  of  the  FCC  Rules.  These  limits aredesigned  to  provide  reasonable  protection  against harmful  interference  in  a  residential  installation.  This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However,  there  is  no  guarantee  that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
  correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase  the  separation  between  the  equipment  and receiver.  Connect  the  equipment  into  an  outlet  on  a  circuit different from that to which the receiver is connected.  Consult  the  dealer  or  an  experienced  radio/TV technician for help  Caution:Changes  or  modifications  not  expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.    Warning:This device complies with Part 15 of the FCC Rules.  Operation  is  subject  to  the  following  two conditions:  (1)  this  device  may  not  cause  harmful interference,  and(2)  this  device  must  accept  any interference  received,  including  interference  that  may cause undesired operation.

Navigation menu