Locks PS902 Instructions 106440
User Manual: Locks PS902 Instructions Mayflower Sales - Schlage Electronics
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
*44487023* PS902 44487023 Power Supply Installation Instructions DANGER To avoid risk of electric shock, turn off AC power before installing or servicing PS902 power supply These instructions cover the following parts: 900-KL Keylock (optional) - Page 2 : NING ! WAR : NING ! WAR ! ER NG DA F1 : ER NG ! DA 900-BB Battery Backup (optional) - Page 3 PS902 Power Supply - Pages 1-3 PS902 Power Supply Specifications: Input 120/240 VAC, 1.1 A, 50/60Hz, High Voltage Class 1 Wiring Required Output 2 Amp DC @ 12/24 VDC Enclosure 14” H x 12” W x 4” D (8 knockouts, 1/2” or 3/4” ) Temperature Range 32°-120° F (0°- 49° C) Fuse F1, T3.15A 250VAC CAUTION For protection against risk of fire, replace fuse with same type and rating Compliance UL 294, ULC-S318, RoHS, & FCC Part 15, Class 2 Output Compatible Boards 900-2RS INST. INSTRUCTIONS - 24125007 (Optional, 1 board maximum) 900-2Q INST. INSTRUCTIONS - 44487098 900-4R INST. INSTRUCTIONS - 44487106 900-4RL INST. INSTRUCTIONS - 44487080 900-8F INST. INSTRUCTIONS - 44487106 900-8P Fire Alarm Input Board (Optional) 900-FA INST. INSTRUCTIONS - 44487106 INST. INSTRUCTIONS - 44487072 Battery Backup Board (Optional) 900-BB INST. INSTRUCTIONS - 44487064 Mounting notes The PS902 must be installed in accordance with the article 760 of the National Electrical Code or NFPA 72, Canadian Electrical Code, or any other applicable codes. Install the PS902 indoors within the protected premises. Check national and local codes for additional installation requirements. Enclosure must be firmly mounted to a solid surface using hardware suitable for the surface. 1 Mount power supply 1a Mark 2 Top Holes 1b Secure Enclosure with 4 Screws x x Board not shown for clarity 2 Secure enclosure door If No Keylock If Keylock Enclosure will be secured with 2 screws as shown (done as last step) Remove knockout and insert key cylinder, then slide in clip OR a b 3 3a 3a PS902 setup and testing Connect AC Wiring DANGER AC Input Ensure AC breaker is turned off Green (Ground) White (Neutral) Black (Hot) NEU LINE AC (In) 120/240 VAC 900-BB Connector ! DANGER High Voltage 3b 24 VDC Output Setting 12 VDC Output Setting 24 If main board must be removed, turn off AC power and wait 8 minutes before removal Use Jumper to Select 24 VDC or 12 VDC Output 12 Do not remove this cover, no serviceable parts F1 OR NC C NO Note: 4 4a 4b Minimum of 1/4” separation between AC and DC wiring as well as power limited and nonpower limited. AC Input (Green LED) DANGER AC Monitor Active when AC present and F1 fuse not open (Form C dry contacts) If AC LED is off, turn AC breaker prior to checking F1 fuse 12/24 VDC Output Terminals 900-FA Connector DC Output (Red LED) Refer to 900-BB instructions for additional info Install 900-BB battery backup (If Included) Battery Supervision Terminals (Form C Dry Contacts) Place Batteries in Box with Terminals to the left NO C NC Attach Wire from Battery Board Red wires = (+) Black wire = (-) (Shown AC Off) Active Inactive AC On AC Off BB LED (Amber) Red Wires = (+) + Note: allow 24 hours for batteries to fully charge Fire Alarm Jumper Remove when 900-FA installed ry tte Ba 2 On-Blinking AC On AC Off Batteries Charging Batteries Supplying Power + On-Solid ry tte Ba 1 Black Wires = (-) 5 • • • Turn on AC breaker to test power supply Verify AC LED is On = GREEN Verify DC LED is On = RED Verify BB LED (if applicable) is On = AMBER 6 Refer to 900-FA instructions for additional info Wire 900-FA (fire alarm board) if included Terminal Definitions NC C NO Supervision Output Contacts Shown FA Active (open) One 900-FA Board - Automatic Reset NC C NO FA1 FA1 Note: If FA is installed on PS902: FA2 • • Fire Alarm Input Verify jumper J13 is removed Power will be removed from PS902 when fire alarm is active One 900-FA Board - Manual Reset NC FA2 C NO FA1 FA2 Manual Reset (Temporarily close to reset) Fire Alarm Contact Closed = no fire Open = fire Fire Alarm Contact Closed = no fire Open = fire Refer to appropriate instructions if any board shown below is factory-installed Option Boards Option 1 Option Board to be Plugged into Option Connector • See option board installation instructions for wiring info Notes: 1. When powering (2) QEL’s with a PS902, both cannot be activated at the same time, they must be sequenced. 2. Latchbolt retraction of (2) sequenced QEL’s requires more than 1 second to complete. 3. For double door QEL applications with auto operators, it is recommended to use a PS904, 906, or 914 power supply. Available option boards: 900-2RS (2 Relay) 900-2Q (2 Relay w/com) 900-4R (4 Relay) 900-4RL (4 Relay w/logic) 900-8F (8 Zone Distribution-fuse) 900-8P (8 Zone Distribution-PTC) NOTE: When installation is complete, secure enclosure door with screws (provided) or keylock Customer Service 1-877-671-7011 www.allegion.com/us © Allegion 2014 Printed in U.S.A. 44487023 Rev. 01/14-c
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2013:12:19 10:56:23-05:00 Creator : Adobe InDesign CS6 (Windows) Modify Date : 2016:02:11 12:44:05-05:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2016:02:11 12:44:05-05:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:90fcd14e-a672-4796-872e-3abb6c36bf70 Original Document ID : xmp.did:31E29F5C3D5CDF11BB6AEFFDF511A3FD Document ID : xmp.id:AC0A8415C668E311A82AD68785E9E205 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:AB0A8415C668E311A82AD68785E9E205 Derived From Document ID : xmp.did:59DEE055BE68E311A82AD68785E9E205 Derived From Original Document ID: xmp.did:31E29F5C3D5CDF11BB6AEFFDF511A3FD Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2013:12:19 10:56:23-05:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 4EXIF Metadata provided by EXIF.tools