Locks 6111/6111DS Installation Instructions 107681

User Manual: Locks 6111/6111DS Installation Instructions Mayflower Sales - Von Duprin

Open the PDF directly: View PDF .
Page Count: 2

*931226-00*

931226-00

Note: Check with factory for retrot applications.

1

For lock or device preparation, see their directions. Also see application schedule on other side.

2

Prepare mullion for strike (see other side).

3

Wire strike (Figure 1). (Switches on 6111DS only.)

4

Test strike: Apply solenoid power. Fail secure (FSE) lip unlocks. Fail safe (FS) lip locks. Figure 1 shows status of switches.

5

Install strike with two #12-24 screws. Make sure clearance between latch bolt and strike lip is 1/32” (Figure 2).

6

If latch bolt does not extend far enough to actuate tripper, install extension (Figure 3). (Tripper on 6111DS only.)

7

Test door: With strike unlocked, door opens with latch bolt extended. When door closes, latch bolt rides over strike lip.

Figure 1

DC input is

nonpolarized.

NOTE

!

J1

J2 P2

Switches hown with tripper

depressed, strike lip closed and locked

(switches and tripper on 6111DS only)

P1

P1 J1A P1A

SO-12 or SO-24

12 VDC

or

24 VDC

12 VAC SO-12 12 VDC

or

24 VAC SO-24 24 VDC

{

{

J2

Fail safe (FS)

J2

Fail secure (FSE)

S1

S2

1

2

3

4

5

6

S1

S2

1

2

3

4

5

6

Wiring

for DC

supply

Wiring

for AC

supply

Solenoid

Standard: 5 A, 30 VDC

Gold: 0.25 A, 30 VDC

SWITCH RATINGS

}

P2

Red (C)

Blue

Yellow

White (C)

Gray

Violet }

S1

(monitors

tripper)

S2

(monitors

strike lip)

Use crimp

connectors to

splice field wiring

to P1 leads

Yellow solenoid wires = 12 VDC, 0.57 A

Black solenoid wires = 24 VDC, 0.29 A

(also shown on strike label)

SOLENOID POWER REQUIREMENTS

Use crimp connectors to

splice field wiring to P2

leads; insulate unused leads

Tripper

Figure 3

Extension

Figure 2

Top view;

faceplate not

shown for clarity

1/32”

Latch

bolt

Strike

lip

NOTE:

Static Strength Rating 1500 lb.

Dynamic Strength Rating 70ft.-lb.

Endurance Rating 250,000 c.

89/336/EEC

Electric Strike Double Door with Mullion Rim Application

6111/6111DS

Installation Instructions

© Allegion 2014

Printed in U.S.A.

931226-00 Rev. 01/14-c

Mullion Preparation for Strike

Von Duprin Device “B”

22 Rim and 98/99 Rim 3-7/16”

33/35 Rim EO/DT/NL/TP 2-13/32”

33A/35A Series Rim 2-15/32”

44/88 Rim EO/DT/NL/TP 3-1/2”

44/88 Rim K 3-3/8”

For other devices, consult factory.

“B”

Application Schedule

RHR shown active

LHR shown inactive

“B”

299 or

268 strike

3/16”

ref.

5/16”

minimum

2-5/8”

#16 drill and

#12-24 tap

2 places

Electric strike

4-1/2”

X

XX

X

Line X-X corresponds to

line X-X on device template

5-1/4”

1-3/32”

4854 or DL 4854

mullion

1/2” 3/4”

2-3/16”

1-7/16”

#25 drill and

#10-24 tap

2 places

1-15/16”

1/2”

2-1/8”

3/4”

1-1/16”

2-1/4”

C strike and

device

L

#25 drill and #10-24 tap

for 268 strike only

on DL 4854

Customer Service

1-877-671-7011 www.allegion.com/us